ROUTING-MIB Table View

This table augments the MIB-II ipNetToMediaTable by providing
per-interface ARP entry information.

agentSwitchArpEntry row .1.3.6.1.4.1.7244.2.2.1.10.1

Indexes

agentSwitchArpIpAddress

Column	Syntax	OID
agentSwitchArpAgeobsolete This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.	SNMPv2-SMITimeTicks Constraints: range: 0-63	.1.3.6.1.4.1.7244.2.2.1.10.1.1
agentSwitchArpIpAddressobsolete The IP Address assigned to each interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.1.10.1.2
agentSwitchArpMacAddressobsolete The hardware MAX Address that each interface maps to.	RFC1213-MIBPhysAddressr/w Constraints: range: 0-63	.1.3.6.1.4.1.7244.2.2.1.10.1.3
agentSwitchArpInterfaceobsolete The Associated IfIndex which identified the ARP Entry.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.1.10.1.4
agentSwitchArpTypeobsolete The type of ARP entry.	Enumeration Enumerated Values: 1 local 2 gateway 3 static 4 dynamic	.1.3.6.1.4.1.7244.2.2.1.10.1.5
agentSwitchArpStatusobsolete The status of this ARP entry. Setting this object destroy will remove the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.1.10.1.6

This table contains the per-interface configuration
parameters for Local Proxy Arp.

agentSwitchLocalProxyArpEntry row .1.3.6.1.4.1.7244.2.2.1.11.1

Represents a logical row in the
agentSwitchLocalProxyArpTable

Indexes

IF-MIBifIndex

Column	Syntax	OID
agentSwitchLocalProxyArpMode The Local Proxy Arp Mode for the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.1.11.1.1

This table augments the MIB-II ipNetToMediaTable by providing
per-interface ARP entry information.

agentSwitchIntfArpEntry row .1.3.6.1.4.1.7244.2.2.1.12.1

Indexes

agentSwitchIntfArpIpAddress agentSwitchIntfArpIfIndex

Column	Syntax	OID
agentSwitchIntfArpIpAddress The Type of Address assigned to this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.1.12.1.1
agentSwitchIntfArpIfIndex The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface	IF-MIBInterfaceIndex Constraints: range: 1-250000 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.7244.2.2.1.12.1.2
agentSwitchIntfArpAge This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.	SNMPv2-SMITimeTicks Constraints: range: 1-500000	.1.3.6.1.4.1.7244.2.2.1.12.1.3
agentSwitchIntfArpMacAddress The hardware MAX Address that each interface maps to.	RFC1213-MIBPhysAddressr/w Constraints: range: 0-100	.1.3.6.1.4.1.7244.2.2.1.12.1.4
agentSwitchIntfArpType The type of ARP entry.	Enumeration Enumerated Values: 1 local 2 gateway 3 static 4 dynamic Constraints: range: 0-1000000	.1.3.6.1.4.1.7244.2.2.1.12.1.5
agentSwitchIntfArpStatus The status of this ARP entry. Setting this object destroy will remove the entry.	SNMPv2-TCRowStatusr/w Constraints: range: 0-16 Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.1.12.1.6

There is no global administrative flag for router discovery.  The global
routing flag (agentSwitchIpRoutingMode) will be used for this purpose.  If routing
is disabled, router discovery is disabled as well.

agentSwitchIpRouterDiscoveryEntry row .1.3.6.1.4.1.7244.2.2.2.4.1

Indexes

agentSwitchIpRouterDiscoveryIfIndex

Column	Syntax	OID
agentSwitchIpRouterDiscoveryIfIndex Interface Number to configure Router Discovery on.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.7244.2.2.2.4.1.1
agentSwitchIpRouterDiscoveryAdvertiseMode Enable or disable router discovery on the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.2.4.1.2
agentSwitchIpRouterDiscoveryMaxAdvertisementInterval Maximum time allowed between sending router advertisements from the interface.	Integer32r/w Constraints: range: 4-1800	.1.3.6.1.4.1.7244.2.2.2.4.1.3
agentSwitchIpRouterDiscoveryMinAdvertisementInterval Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.	Integer32r/w Constraints: range: 3-1800	.1.3.6.1.4.1.7244.2.2.2.4.1.4
agentSwitchIpRouterDiscoveryAdvertisementLifetime Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.	Integer32r/w Constraints: range: 4-9000	.1.3.6.1.4.1.7244.2.2.2.4.1.5
agentSwitchIpRouterDiscoveryPreferenceLevel Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.2.4.1.6
agentSwitchIpRouterDiscoveryAdvertisementAddress Address used when sending router advertisements from the interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.2.4.1.7

Contains a list of secondary IP Addresses associated with an interface.

agentSwitchSecondaryAddressEntry row .1.3.6.1.4.1.7244.2.2.2.6.1

A secondary IP Address for a given interface. This IP Address must not
conflict with the IP Address configured in the agentSwitchIpInterfaceTable.

Indexes

agentSwitchIpInterfaceIfIndex agentSwitchSecondaryIpAddress

Column	Syntax	OID
agentSwitchSecondaryIpAddress The Secondary IP Address assigned to this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.2.6.1.1
agentSwitchSecondaryNetMask The Secondary Net Mask assigned to this interface. This value must be set during creation, and can not be changed.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.2.6.1.2
agentSwitchSecondaryStatus Creates a new entry in the Secondary Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitch…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.2.6.1.3

Replaced by agentSwitchIntfIpHelperAddressTable.

agentSwitchHelperAddressEntry row .1.3.6.1.4.1.7244.2.2.2.7.1

A Helper IP Address for a given interface.

Indexes

agentSwitchIpInterfaceIfIndex agentSwitchHelperIpAddress

Column	Syntax	OID
agentSwitchHelperIpAddressobsolete The Helper IP Address assigned to this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.2.7.1.1
agentSwitchHelperStatusobsolete Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchHel…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.2.7.1.2

Contains a list of IP helper addresses associated with an interface.

agentSwitchIntfIpHelperAddressEntry row .1.3.6.1.4.1.7244.2.2.2.10.1

An IP helper address for a given interface.

Indexes

agentSwitchIpInterfaceIfIndex agentSwitchIntfIpHelperUdpPort agentSwitchIntfIpHelperIpAddress

Column	Syntax	OID
agentSwitchIntfIpHelperIpAddress An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.2.10.1.1
agentSwitchIntfIpHelperUdpPort UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry.	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.7244.2.2.2.10.1.2
agentSwitchIntfIpHelperDiscardobsolete Variable obsoleted. To create a discard entry, set the helper address to 0.0.0.0.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.2.10.1.3
agentSwitchIntfIpHelperHitCount The number of times a packet has been forwarded or discarded according to this entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.2.10.1.4
agentSwitchIntfIpHelperStatus Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.2.10.1.5

This table contains the MIB objects required to configure 
route-redistribution for RIP. Here, RIP is the Destination
protocol and the source protocols can be any of : BGP, OSPF,
Static, Connected.

agentRipRouteRedistEntry row .1.3.6.1.4.1.7244.2.2.3.9.1

Indexes

agentRipRouteRedistSource

Column	Syntax	OID
agentRipRouteRedistSource Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.	Enumeration Enumerated Values: 1 connected 2 static 3 ospf	.1.3.6.1.4.1.7244.2.2.3.9.1.1
agentRipRouteRedistMode User enabels/disables route-redistribution for a particular source protocol.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.3.9.1.2
agentRipRouteRedistMetric Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.7244.2.2.3.9.1.3
agentRipRouteRedistMetricConfigured Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.3.9.1.4
agentRipRouteRedistMatchInternal If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.3.9.1.5
agentRipRouteRedistMatchExternal1 If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.3.9.1.6
agentRipRouteRedistMatchExternal2 If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.3.9.1.7
agentRipRouteRedistMatchNSSAExternal1 If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.3.9.1.8
agentRipRouteRedistMatchNSSAExternal2 If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.3.9.1.9
agentRipRouteRedistDistList Access-list number of the access-list, which filters routes received from a source-protocol.	Unsigned32r/w Constraints: range: 1-199	.1.3.6.1.4.1.7244.2.2.3.9.1.10
agentRipRouteRedistDistListConfigured Flag to determine whether Access-list is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.3.9.1.11

A list of subnets which require separate
configuration in RIP.  Augments rip2IfConfTable
 in the RIPv2-MIB.

agentRip2IfConfEntry row .1.3.6.1.4.1.7244.2.2.3.10.1

A Single Routing Domain in a single Subnet.
Augments rip2IfConfEntry in RIPv2-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
agentRip2IfConfAuthKeyId The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7244.2.2.3.10.1.1

This table contains the MIB objects required to configure 
route-redistribution for OSPF. Here, OSPF is the Destination
protocol and the source protocols can be any of : BGP, RIP,
Static, Connected.

agentOspfRouteRedistEntry row .1.3.6.1.4.1.7244.2.2.4.8.1

Indexes

agentOspfRouteRedistSource

Column	Syntax	OID
agentOspfRouteRedistSource Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.	Enumeration Enumerated Values: 1 connected 2 static 3 rip	.1.3.6.1.4.1.7244.2.2.4.8.1.1
agentOspfRouteRedistMode User enabels/disables route-redistribution for a particular source protocol.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.4.8.1.2
agentOspfRouteRedistMetric Metric used for redistributing a particular source protocol route into OSPF.	Integer32r/w Constraints: range: 0-16777214	.1.3.6.1.4.1.7244.2.2.4.8.1.3
agentOspfRouteRedistMetricConfigured Flag to determine whether OSPF redistribute-metric is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.4.8.1.4
agentOspfRouteRedistMetricType Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).	Enumerationr/w Enumerated Values: 1 externalType1 2 externalType2	.1.3.6.1.4.1.7244.2.2.4.8.1.5
agentOspfRouteRedistTag It specifies the tag field in routes redistributed by OSPF. The size list from 0 to 4294967295.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.4.8.1.6
agentOspfRouteRedistSubnets If this value is false, then OSPF will not redistribute subnetted routes.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.4.8.1.7
agentOspfRouteRedistDistList Access-list number of the access-list, which filters routes received from a source-protocol.	Unsigned32r/w Constraints: range: 1-199	.1.3.6.1.4.1.7244.2.2.4.8.1.8
agentOspfRouteRedistDistListConfigured Flag to determine whether Access-list is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.4.8.1.9

The OSPF Interface Table describes the  inter-
faces from the viewpoint of OSPF.  Augments 
 ospfIfTable from the OSPF-MIB.

agentOspfIfEntry row .1.3.6.1.4.1.7244.2.2.4.9.1

The OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF. Augments
ospfIfEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
agentOspfIfAuthKeyId The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7244.2.2.4.9.1.1
agentOspfIfIpMtuIgnoreFlag Configures the IP MTU Ignore Flag value for this OSPF interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.4.9.1.2
agentOspfIfPassiveMode Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.4.9.1.3
agentOspfIfAdvertiseSecondaries Configures the advertisability of the secondary addresses configured on this interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.4.9.1.4

Information about this router's virtual inter-
faces.  Augments ospfVirtIfTable from the OSPF-MIB.

agentOspfVirtIfEntry row .1.3.6.1.4.1.7244.2.2.4.10.1

Information about a single Virtual Interface.
Augments ospfVirtIfEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
agentOspfVirtIfAuthKeyId The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.7244.2.2.4.10.1.1

The OSPF Process's Area Link State Database (LSDB). 
The LSDB contains type-10 Link State Advertisements 
from throughout the areas that the device is attached to.

agentOspfAreaOpaqueLsdbEntry row .1.3.6.1.4.1.7244.2.2.4.16.1

A single AreaOpaque Link State Advertisement.

Indexes

agentOspfAreaOpaqueLsdbAreaId agentOspfAreaOpaqueLsdbType agentOspfAreaOpaqueLsdbLsid agentOspfAreaOpaqueLsdbRouterId

Column	Syntax	OID
agentOspfAreaOpaqueLsdbAreaId The 32 bit identifier of the Area from which the LSA was received.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.16.1.1
agentOspfAreaOpaqueLsdbType The type of the link state advertisement. Each link state type has a separate advertisement format.	Enumeration Enumerated Values: 10 areaOpaqueLink	.1.3.6.1.4.1.7244.2.2.4.16.1.2
agentOspfAreaOpaqueLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.16.1.3
agentOspfAreaOpaqueLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.16.1.4
agentOspfAreaOpaqueLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.16.1.5
agentOspfAreaOpaqueLsdbAge This field is the age of the link state advertisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.16.1.6
agentOspfAreaOpaqueLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.16.1.7
agentOspfAreaOpaqueLsdbAdvertisement The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.4.16.1.8

The OSPF Process's Link-Local Link State Database 
for non-virtual links. 
This table is identical to the OSPF LSDB Table 
in format, but contains only Link-Local Link State 
Advertisements for non-virtual links. The purpose is 
to allow Link-Local LSAs to be displayed for each 
non-virtual interface. This table is implemented to 
support type-9 LSAs which are defined 
in 'The OSPF Opaque LSA Option'.

agentOspfLocalLsdbEntry row .1.3.6.1.4.1.7244.2.2.4.17.1

A single Link State Advertisement.

Indexes

agentOspfLocalLsdbIpAddress agentOspfLocalLsdbAddressLessIf agentOspfLocalLsdbType agentOspfLocalLsdbLsid agentOspfLocalLsdbRouterId

Column	Syntax	OID
agentOspfLocalLsdbIpAddress The IP Address of the interface from which the LSA was received if the interface is numbered.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.17.1.1
agentOspfLocalLsdbAddressLessIf The Interface Index of the interface from which the LSA was received if the interface is unnumbered.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.7244.2.2.4.17.1.2
agentOspfLocalLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 9 localOpaqueLink	.1.3.6.1.4.1.7244.2.2.4.17.1.3
agentOspfLocalLsdbLsid The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.17.1.4
agentOspfLocalLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.7244.2.2.4.17.1.5
agentOspfLocalLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.17.1.6
agentOspfLocalLsdbAge This field is the age of the link state adver- tisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.17.1.7
agentOspfLocalLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The check…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.17.1.8
agentOspfLocalLsdbAdvertisement The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.4.17.1.9

The OSPF Process's AS-scope LSA Link State Database. 
The Database contains the AS-scope Link State 
Advertisements from throughout the areas that 
the device is attached to. 
          
This table is identical to the OSPF LSDB Table 
in format, but contains only AS-scope Link State 
Advertisements.  The purpose is to allow AS-scope 
LSAs to be displayed once for the router rather 
than once in each non-stub area.

agentOspfAsLsdbEntry row .1.3.6.1.4.1.7244.2.2.4.18.1

A single Link State Advertisement.

Indexes

agentOspfAsLsdbType agentOspfAsLsdbLsid agentOspfAsLsdbRouterId

Column	Syntax	OID
agentOspfAsLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 11 asOpaqueLink	.1.3.6.1.4.1.7244.2.2.4.18.1.1
agentOspfAsLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.18.1.2
agentOspfAsLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.7244.2.2.4.18.1.3
agentOspfAsLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.18.1.4
agentOspfAsLsdbAge This field is the age of the link state adver- tisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.18.1.5
agentOspfAsLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The check…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.4.18.1.6
agentOspfAsLsdbAdvertisement The entire Link State Advertisement, including its header.	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.4.18.1.7

The OSPF Global Area Id Configuration Table.

agentOspfNetworkAreaEntry row .1.3.6.1.4.1.7244.2.2.4.23.1

The OSPF Global Area Id Configuration Table.

Indexes

agentOspfNetworkAreaIpAddress agentOspfNetworkAreaWildcardMask agentOspfNetworkAreaId

Column	Syntax	OID
agentOspfNetworkAreaIpAddress The OSPF Ip Address of Global Area Id Configuration Table.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.23.1.1
agentOspfNetworkAreaWildcardMask The OSPF Wildcard Mask of Global Area Id Configuration Table.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.23.1.2
agentOspfNetworkAreaId The OSPF Area Id of Global Area Id Configuration Table.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.4.23.1.3
agentOspfNetworkAreaRowStatus The OSPF Row Status of Global Area Id Configuration Table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.4.23.1.4

Operations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
`agentRouterVrrpConfiguredEntry' items.

agentRouterVrrpConfiguredEntry row .1.3.6.1.4.1.7244.2.2.8.2.1

An entry in the table contains operational priority that is
associated with a virtual router.

Indexes

IF-MIBifIndex VRRP-MIBvrrpOperVrId

Column	Syntax	OID
agentRouterVrrpConfiguredPriority This object specifies the value set by the vrrpOperPriority object. The GET operation on 'vrrpOperPriority' will be affected by both the tracking process and the configured priority set by the vrrpOperPriority object.	Integer32 Constraints: range: 1-254	.1.3.6.1.4.1.7244.2.2.8.2.1.1

Operations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
`agentRouterVrrpOperEntry' items.

agentRouterVrrpOperEntry row .1.3.6.1.4.1.7244.2.2.9.1.1

An entry in the table contains operational priority that is
associated with a virtual router.

Indexes

IF-MIBifIndex VRRP-MIBvrrpOperVrId

Column	Syntax	OID
agentRouterVrrpOperPriorityobsolete This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.7244.2.2.9.1.1.1

Tracking table for a VRRP router which consists of
agentRouterVrrpTrackIntfEntry items.

agentRouterVrrpTrackIntfEntry row .1.3.6.1.4.1.7244.2.2.10.1.1

An entry in the table contains tracked IP interfaces
associated with a virtual router.

Indexes

IF-MIBifIndex VRRP-MIBvrrpOperVrId agentRouterVrrpTrackIntf

Column	Syntax	OID
agentRouterVrrpTrackIntf This object specifies the interface to be tracked.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.7244.2.2.10.1.1.1
agentRouterVrrpTrackIfPrioDec This object specifies the decrement priority of the VRRP router.	Integer32r/w Constraints: range: 1-254	.1.3.6.1.4.1.7244.2.2.10.1.1.2
agentRouterVrrpTrackIfState This object specifies the IP state of the tracked interface for the virtual router.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.10.1.1.3
agentRouterVrrpTrackIfStatus The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.10.1.1.4

Tracking table for a VRRP router which consists of a
'agentRouterVrrpTrackRouteEntry' items.

agentRouterVrrpTrackRouteEntry row .1.3.6.1.4.1.7244.2.2.10.2.1

An entry in the table contains tracked Routes
associated with a virtual router.

Indexes

IF-MIBifIndex VRRP-MIBvrrpOperVrId agentRouterVrrpTrackRtPfx agentRouterVrrpTrackRtPfxLen

Column	Syntax	OID
agentRouterVrrpTrackRtPfx This object specifies the prefix of the route to be tracked.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.10.2.1.1
agentRouterVrrpTrackRtPfxLen This object specifies prefix length of the route to be tracked.	Integer32 Constraints: range: 0-32	.1.3.6.1.4.1.7244.2.2.10.2.1.2
agentRouterVrrpTrackRtPrioDec This object specifies the decrement priority of the VRRP router.	Integer32r/w Constraints: range: 1-254	.1.3.6.1.4.1.7244.2.2.10.2.1.3
agentRouterVrrpTrackRtReachable This object specifies the reachability of the tracked route.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.10.2.1.4
agentRouterVrrpTrackRtStatus The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.10.2.1.5

Contains a list of IP helper addresses configured globally.

agentSwitchIpHelperAddressEntry row .1.3.6.1.4.1.7244.2.2.11.8.1

An IP Helper address that applies to packets received on any interface.

Indexes

agentSwitchIpHelperAddress agentSwitchIpHelperUdpPort

Column	Syntax	OID
agentSwitchIpHelperAddress The IP Helper address assigned to this interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7244.2.2.11.8.1.1
agentSwitchIpHelperUdpPort UDP port number. 0 is the default port.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.7244.2.2.11.8.1.2
agentSwitchIpHelperHitCount The number of times a packet has been forwarded or discarded according to this entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.11.8.1.3
agentSwitchIpHelperStatus Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.11.8.1.4

Contains a list of VLAN IDs used internally for port-based routing interfaces.

agentSwitchInternalVlanEntry row .1.3.6.1.4.1.7244.2.2.12.3.1

A VLAN ID internally assigned to a port-based routing interface.

Indexes

agentSwitchInternalVlanId

Column	Syntax	OID
agentSwitchInternalVlanId A VLAN ID internally assigned to a port-based routing interface.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.7244.2.2.12.3.1.1
agentSwitchInternalVlanIfIndex Interface index of port-based routing interface using this VLAN ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7244.2.2.12.3.1.2

Contains a list of IP helper addresses configured globally.

agentRouterIsisConfigEntry row .1.3.6.1.4.1.7244.2.2.13.1.1

An IP Helper address that applies to packets received on any interface.

Indexes

agentRouterIsisConfigAreaIndex

Column	Syntax	OID
agentRouterIsisConfigAreaIndex Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.1
agentRouterIsisConfigAreaTag Sets the area tag for isis area.	OctetStringr/w Constraints: range: 1-20	.1.3.6.1.4.1.7244.2.2.13.1.1.2
agentRouterIsisConfigSpfLevel1Interval Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.3
agentRouterIsisConfigSpfLevel2Interval Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.4
agentRouterIsisConfigLspLifeTimeIntervalobsolete Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.5
agentRouterIsisConfigLspRefreshTimeIntervalobsolete Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.6
agentRouterIsisConfigGenaralInterval1TimeIntervalobsolete Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.7
agentRouterIsisConfigGenaralInterval2TimeIntervalobsolete Sets the area index for isis area.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.8
agentRouterIsisConfigIsTypeobsolete level1 is mean level 1, level2 is mean level 2, level12 is mean both level 1 and 2	Enumerationr/w Enumerated Values: 1 level1 2 level2 3 level12	.1.3.6.1.4.1.7244.2.2.13.1.1.9
agentRouterIsisConfigMetricTypeobsolete narrow is mean old style, wide is mean new style, transition is mean both style	Enumerationr/w Enumerated Values: 0 narrow 1 wide 2 transition	.1.3.6.1.4.1.7244.2.2.13.1.1.10
agentRouterIsisConfigHostnameobsolete Set the hostname option	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.7244.2.2.13.1.1.11
agentRouterIsisConfigDistantobsolete Set the ISIS distant	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.12
agentRouterIsisConfigDefaultMetricobsolete Set the ISIS default metric	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7244.2.2.13.1.1.13
agentRouterIsisConfigDefaultInformationobsolete Set the hostname option	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.7244.2.2.13.1.1.14
agentRouterIsisConfigDomainPasswoad Sets the domain password string.	OctetStringr/w Constraints: range: 1-256	.1.3.6.1.4.1.7244.2.2.13.1.1.15
agentRouterIsisConfigDomainPasswoadAuthTypeobsolete Set the domain password auth type	Enumerationr/w Enumerated Values: 0 none 1 sendOnly 3 validate	.1.3.6.1.4.1.7244.2.2.13.1.1.16
agentRouterIsisConfigAreaPasswoad Sets the domain password string.	OctetStringr/w Constraints: range: 1-256	.1.3.6.1.4.1.7244.2.2.13.1.1.17
agentRouterIsisConfigAreaPasswoadAuthTypeobsolete Set the domain password auth type	Enumerationr/w Enumerated Values: 0 none 1 sendOnly 3 validate	.1.3.6.1.4.1.7244.2.2.13.1.1.18
agentRouterIsisConfigAreaNET1 Sets the area tag for isis area.	OctetStringr/w Constraints: range: 1-50	.1.3.6.1.4.1.7244.2.2.13.1.1.19
agentRouterIsisConfigAreaNET2 Sets the area tag for isis area.	OctetStringr/w Constraints: range: 1-50	.1.3.6.1.4.1.7244.2.2.13.1.1.20
agentRouterIsisConfigAreaNET3 Sets the area tag for isis area.	OctetStringr/w Constraints: range: 1-50	.1.3.6.1.4.1.7244.2.2.13.1.1.21
agentRouterIsisConfigStatusobsolete Sets the area index for isis area.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.13.1.1.22

This table contains the MIB objects required to configure 
route-redistribution for RIP. Here, ISIS is the Destination
protocol and the source protocols can be any of : BGP, OSPF, Rip
Static, Connected.

agentIsisRouteRedistEntry row .1.3.6.1.4.1.7244.2.2.13.2.1

Indexes

agentRouterIsisConfigAreaIndex agentIsisRouteRedistSource

Column	Syntax	OID
agentIsisRouteRedistSource Source route, from which ISIS can redistribute routes. This object also acts as the identifier for the ISIS redistribution Table entry.	Enumeration Enumerated Values: 1 connected 2 static 3 ospf 4 rip	.1.3.6.1.4.1.7244.2.2.13.2.1.1
agentIsisRouteRedistMode User enabels/disables route-redistribution for a particular source protocol.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.7244.2.2.13.2.1.2
agentIsisRouteRedistMetric Metric used for redistributing a particular source protocol route into Isis. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).	Integer32r/w Constraints: range: 0-16777214	.1.3.6.1.4.1.7244.2.2.13.2.1.3
agentIsisRouteRedistMetricConfigured Flag to determine whether Isis redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.13.2.1.4
agentIsisRouteRedistMatchInternal If this flag is true, Isis redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.13.2.1.5
agentIsisRouteRedistMatchExternal1 If this flag is true, Isis redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.13.2.1.6
agentIsisRouteRedistMatchExternal2 If this flag is true, Isis redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.13.2.1.7
agentIsisRouteRedistMatchNSSAExternal1 If this flag is true, Isis redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.13.2.1.8
agentIsisRouteRedistMatchNSSAExternal2 If this flag is true, Isis redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.7244.2.2.13.2.1.9
agentIsisRouteRedistDistList Access-list number of the access-list, which filters routes received from a source-protocol.	Unsigned32r/w Constraints: range: 1-199	.1.3.6.1.4.1.7244.2.2.13.2.1.10
agentIsisRouteRedistDistListConfigured Flag to determine whether Access-list is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.7244.2.2.13.2.1.11

The ISIS Interface Table describes the  inter-
faces from the viewpoint of ISIS.

agentIsisConfigIfEntry row .1.3.6.1.4.1.7244.2.2.13.3.1

The ISIS Interface Entry describes one inter-
face from the viewpoint of Ripng.

Indexes

agentIsisConfigIfIndex

Column	Syntax	OID
agentIsisConfigIfIndex The IfIndex associated with this instance.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.7244.2.2.13.3.1.1
agentIsisConfigIfArea Configures interface isis area.	OctetStringr/w	.1.3.6.1.4.1.7244.2.2.13.3.1.2
agentIsisConfigIfCircuitTypeobsolete level1 is mean level 1, level2 is mean level 2, level12 is mean both level 1 and 2	Enumerationr/w Enumerated Values: 1 level1 2 level2 3 level12	.1.3.6.1.4.1.7244.2.2.13.3.1.3
agentIsisConfigIfCSNPIntervalL1 Set Level CSNP transition interval	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.13.3.1.4
agentIsisConfigIfCSNPIntervalL2 Set Leve2 CSNP transition interval	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.13.3.1.5
agentIsisConfigIfHelloIntervalL1 Set Leve1 Hello transition interval	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.13.3.1.6
agentIsisConfigIfHelloIntervalL2 Set Leve2 Hello transition interval	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.7244.2.2.13.3.1.7
agentIsisConfigIfHelloMultiL1 Set Leve1 Hello multipliter	Unsigned32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.7244.2.2.13.3.1.8
agentIsisConfigIfHelloMultiL2 Set Leve2 Hello multipliter	Unsigned32r/w Constraints: range: 3-1000	.1.3.6.1.4.1.7244.2.2.13.3.1.9
agentIsisConfigIfHelloPadobsolete Set Hello packet padding mode	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.7244.2.2.13.3.1.10
agentIsisConfigIfMetricL1 Set Leve1 interface metric	Unsigned32r/w Constraints: range: 1-16777214	.1.3.6.1.4.1.7244.2.2.13.3.1.11
agentIsisConfigIfMetricL2 Set Leve2 interface metric	Unsigned32r/w Constraints: range: 1-16777214	.1.3.6.1.4.1.7244.2.2.13.3.1.12
agentIsisConfigIfPriorityL1 Set Leve1 interface priority	Unsigned32r/w Constraints: range: 0-127	.1.3.6.1.4.1.7244.2.2.13.3.1.13
agentIsisConfigIfPriorityL2 Set Leve2 interface priority	Unsigned32r/w Constraints: range: 0-127	.1.3.6.1.4.1.7244.2.2.13.3.1.14
agentIsisConfigIfPasswoad Sets the interface password string.	OctetStringr/w Constraints: range: 1-256	.1.3.6.1.4.1.7244.2.2.13.3.1.15
agentIsisConfigIfPasswoadAuthTypeobsolete Set the interface password auth type	Enumerationr/w Enumerated Values: 0 none 1 sendOnly 3 validate	.1.3.6.1.4.1.7244.2.2.13.3.1.16
agentIsisConfigifStatusobsolete Sets the area index for isis area.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7244.2.2.13.3.1.17