RAISECOM-DOT1AG-MIB Table View

There is one CFM Stack table per bridge. It permits
the retrieval of information about the Maintenance Points
configured on any given interface.

rcDot1agCfmStackEntry row .1.3.6.1.4.1.8886.6.1.32.1.1.1.1

The Stack table entry

Indexes

rcDot1agCfmStackifIndex rcDot1agCfmStackVlanIdOrNone rcDot1agCfmStackMdLevel rcDot1agCfmStackDirection

Column	Syntax	OID
rcDot1agCfmStackifIndex This object represents the Bridge Port or aggregated port on which MEPs or MHFs might be configured. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable, and …	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.1
rcDot1agCfmStackVlanIdOrNone VLAN ID to which the MP is attached, or 0, if none.	Q-BRIDGE-MIBVlanIdOrNone Type Constraints: range: 0..4094	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.2
rcDot1agCfmStackMdLevel MD Level of the Maintenance Point.	IEEE8021-CFM-MIBDot1agCfmMDLevel Type Constraints: range: 0..7	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.3
rcDot1agCfmStackDirection Direction in which the MP faces on the Bridge Port	IEEE8021-CFM-MIBDot1agCfmMpDirection Type Values: 1 down 2 up	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.4
rcDot1agCfmStackMdIndex The index of the Maintenance Domain in the rcDot1agCfmMdTable to which the MP is associated, or 0, if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.5
rcDot1agCfmStackMaIndex The index of the MA in the rcDot1agCfmMaNetTable and rcDot1agCfmMaCompTable to which the MP is associated, or 0, if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.6
rcDot1agCfmStackMepId If an MEP is configured, the MEPID, else 0	IEEE8021-CFM-MIBDot1agCfmMepIdOrZero Type Constraints: range: 0..8191	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.7
rcDot1agCfmStackMacAddress MAC address of the MP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.1.1.1.8

For each bridge component, the Default MD Level Managed Object
controls MHF creation for VIDs that are not attached to a
specific Maintenance Association Managed Object, and Sender ID
TLV transmission by those MHFs.
          
For each Bridge Port, and for each VLAN ID whose data can
pass through that Bridge Port, an entry in this table is
used by the algorithm in subclause 22.2.3 only if there is no
entry in the Maintenance Association table defining an MA
for the same VLAN ID and MD Level as this table's entry, and
on which MA an Up MEP is defined.  If there exists such an
MA, that MA's objects are used by the algorithm in
subclause 22.2.3 in place of this table entry's objects.  The
agent maintains the value of rcDot1agCfmDefaultMdStatus to
indicate whether this entry is overridden by an MA.
          
When first initialized, the agent creates this table
automatically with entries for all VLAN IDs,
with the default values specified for each object.
          
After this initialization, the writable objects in this
table need to be persistent upon reboot or restart of a
device.

rcDot1agCfmDefaultMdEntry row .1.3.6.1.4.1.8886.6.1.32.1.2.4.1

The Default MD Level table entry.

Indexes

rcDot1agCfmDefaultMdComponentId rcDot1agCfmDefaultMdPrimaryVid

Column	Syntax	OID
rcDot1agCfmDefaultMdComponentId The bridge component within the system to which the information in this rcDot1agCfmDefaultMdEntry applies. If the system is not a Bridge, or if only one component is present in the Bridge, then this variable (index) mu…	IEEE8021-CFM-MIBDot1agCfmPbbComponentIdentifier Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.1
rcDot1agCfmDefaultMdPrimaryVid The Primary VID of the VLAN to which this entry's objects apply.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.2
rcDot1agCfmDefaultMdStatus State of this Default MD Level table entry. True if there is no entry in the Maintenance Association table defining an MA for the same VLAN ID and MD Level as this table's entry, and on which MA an Up MEP is defined, e…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.3
rcDot1agCfmDefaultMdLevel A value indicating the MD Level at which MHFs are to be created, and Sender ID TLV transmission by those MHFs is to be controlled, for the VLAN to which this entry's objects apply. If this object has the value -1, the …	IEEE8021-CFM-MIBDot1agCfmMDLevelOrNoner/w Type Constraints: range: -1..7	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.4
rcDot1agCfmDefaultMdMhfCreation A value indicating if the Management entity can create MHFs (MIP Half Function) for this VID at this MD Level. If this object has the value defMHFdefer, MHF creation for this VLAN is controlled by rcDot1agCfmDefaultMdD…	IEEE8021-CFM-MIBDot1agCfmMhfCreationr/w Type Values: 1 defMHFnone 2 defMHFdefault 3 defMHFexplicit 4 defMHFdefer	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.5
rcDot1agCfmDefaultMdIdPermission Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MHFs created by the Default Maintenance Domain. If this object has the value sendIdDefer, Sender ID TLV tran…	IEEE8021-CFM-MIBDot1agCfmIdPermissionr/w Type Values: 1 sendIdNone 2 sendIdChassis 3 sendIdManage 4 sendIdChassisManage 5 sendIdDefer	.1.3.6.1.4.1.8886.6.1.32.1.2.4.1.6

This table defines the association of VIDs into VLANs.  There
is an entry in this table, for each component of the bridge,
for each VID that is:
    a) a VID belonging to a VLAN associated with more than
       one VID; and
    b) not the Primary VLAN of that VID.
The entry in this table contains the Primary VID of the VLAN.
          
By default, this table is empty, meaning that every VID is
the Primary VID of a single-VID VLAN.
          
VLANs that are associated with only one VID SHOULD NOT have
an entry in this table.
          
The writable objects in this table need to be persistent
upon reboot or restart of a device.

rcDot1agCfmVlanEntry row .1.3.6.1.4.1.8886.6.1.32.1.3.1.1

The VLAN table entry.

Indexes

rcDot1agCfmVlanComponentId rcDot1agCfmVlanVid

Column	Syntax	OID
rcDot1agCfmVlanComponentId The bridge component within the system to which the information in this rcDot1agCfmVlanEntry applies. If the system is not a Bridge, or if only one component is present in the Bridge, then this variable (index) must be…	IEEE8021-CFM-MIBDot1agCfmPbbComponentIdentifier Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.3.1.1.1
rcDot1agCfmVlanVid This is a VLAN ID belonging to a VLAN that is associated with more than one VLAN ID, and this is not the Primary VID of the VLAN.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.8886.6.1.32.1.3.1.1.2
rcDot1agCfmVlanPrimaryVid This is the Primary VLAN ID of the VLAN with which this entry's rcDot1agCfmVlanVid is associated. This value must not equal the value of rcDot1agCfmVlanVid.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.8886.6.1.32.1.3.1.1.3
rcDot1agCfmVlanRowStatus The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.3.1.1.4

The CFM Configuration Error List table provides a list of
Interfaces and VIDs that are incorrectly configured.

rcDot1agCfmConfigErrorListEntry row .1.3.6.1.4.1.8886.6.1.32.1.4.1.1

The Config Error List Table entry

Indexes

rcDot1agCfmConfigErrorListVid rcDot1agCfmConfigErrorListIfIndex

Column	Syntax	OID
rcDot1agCfmConfigErrorListVid The VLAN ID of the VLAN with interfaces in error.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.8886.6.1.32.1.4.1.1.1
rcDot1agCfmConfigErrorListIfIndex This object is the IfIndex of the interface. Upon a restart of the system, the system SHALL, if necessary, change the value of this variable so that it indexes the entry in the interface table with the sa…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.8886.6.1.32.1.4.1.1.2
rcDot1agCfmConfigErrorListErrorType A vector of Boolean error conditions from 22.2.4, any of which may be true: 0) CFMleak; 1) ConflictingVids; 2) ExcessiveLevels; 3) OverlappedLevels.	IEEE8021-CFM-MIBDot1agCfmConfigErrors Type Values: 0 cfmLeak 1 conflictingVids 2 excessiveLevels 3 overlappedLevels	.1.3.6.1.4.1.8886.6.1.32.1.4.1.1.3

The Maintenance Domain table. Each row in the table
represents a different Maintenance Domain.
          
A Maintenance Domain is described in 802.1ag (3.21) as the
network or the part of the network for which faults in
connectivity are to be managed. The boundary of a Maintenance
Domain is defined by a set of DSAPs, each of which can become
a point of connectivity to a service instance.

rcDot1agCfmMdEntry row .1.3.6.1.4.1.8886.6.1.32.1.5.2.1

The Maintenance Domain table entry. This entry is not lost
upon reboot. It is backed up by stable storage.

Indexes

rcDot1agCfmMdIndex

Column	Syntax	OID
rcDot1agCfmMdIndex The index to the Maintenance Domain table. rcDot1agCfmMdTableNextIndex needs to be inspected to find an available index for row-creation. Referential integrity is required, i.e., the index …	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.1
rcDot1agCfmMdFormat The type (and thereby format) of the Maintenance Domain Name.	IEEE8021-CFM-MIBDot1agCfmMaintDomainNameTyper/w Type Values: 1 none 2 dnsLikeName 3 macAddressAndUint 4 charString	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.2
rcDot1agCfmMdName The Maintenance Domain name. The type/format of this object is determined by the value of the rcDot1agCfmMdNameType object. Each Maintenance Domain has unique name amongst all those used or available to…	IEEE8021-CFM-MIBDot1agCfmMaintDomainNamer/w Type Constraints: range: 1..43	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.3
rcDot1agCfmMdMdLevel The Maintenance Domain Level.	IEEE8021-CFM-MIBDot1agCfmMDLevelr/w Type Constraints: range: 0..7	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.4
rcDot1agCfmMdMhfCreation Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is n…	IEEE8021-CFM-MIBDot1agCfmMhfCreationr/w Type Values: 1 defMHFnone 2 defMHFdefault 3 defMHFexplicit 4 defMHFdefer	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.5
rcDot1agCfmMdMhfIdPermission Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Dom…	IEEE8021-CFM-MIBDot1agCfmIdPermissionr/w Type Values: 1 sendIdNone 2 sendIdChassis 3 sendIdManage 4 sendIdChassisManage 5 sendIdDefer	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.6
rcDot1agCfmMdMaNextIndex Value to be used as the index of the MA table entries, both the rcDot1agCfmMaNetTable and the rcDot1agCfmMaCompTable, for this Maintenance Domain when the management entity wants to create a new row in those tables.	IEEE8021-CFM-MIBDot1afCfmIndexIntegerNextFree Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.7
rcDot1agCfmMdRowStatus The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.5.2.1.8

The Maintenance Association table.  Each row in the table
represents an MA.  An MA is a set of MEPs, each configured
with a single service instance.
          
This is the part of the complete MA table that is constant
across all Bridges in a Maintenance Domain, and across all
components of a single Bridge.  That part of the MA table that
can vary from Bridge component to Bridge component is contained
in the rcDot1agCfmMaCompTable.
          
Creation of a Service Instance establishes a connectionless
association among the selected DSAPs.  Configuring a
Maintenance association End Point (MEP) at each of the
DSAPs creates a Maintenance Association (MA) to monitor
that connectionless connectivity.  The MA is identified by a
Short MA Name that is unique within the Maintenance Domain
and chosen to facilitate easy identification of the Service
Instance.  Together, the Maintenance Domain Name and the
Short MA Name form the Maintenance Association Identifier
(MAID) that is carried in CFM Messages to identify
incorrect connectivity among Service Instances.  A small
integer, the Maintenance association End Point Identifier
(MEPID), identifies each MEP among those configured on a
single MA (802.1ag clauses 3.16 and 18.2).
          
This table uses two indices, first index is the index of the
Maintenance Domain table.  The second index is the same as the
index of the rcDot1agCfmMaCompEntry for the same MA.
          
The writable objects in this table need to be persistent
upon reboot or restart of a device.

rcDot1agCfmMaNetEntry row .1.3.6.1.4.1.8886.6.1.32.1.6.1.1

The MA table entry.

Indexes

rcDot1agCfmMdIndex rcDot1agCfmMaIndex

Column	Syntax	OID
rcDot1agCfmMaIndex Index of the MA table rcDot1agCfmMdMaNextIndex needs to be inspected to find an available index for row-creation.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.8886.6.1.32.1.6.1.1.1
rcDot1agCfmMaNetFormat The type (and thereby format) of the Maintenance Association Name.	IEEE8021-CFM-MIBDot1agCfmMaintAssocNameTyper/w Type Values: 1 primaryVid 2 charString 3 unsignedInt16 4 rfc2865VpnId 32 iccFormat	.1.3.6.1.4.1.8886.6.1.32.1.6.1.1.2
rcDot1agCfmMaNetName The Short Maintenance Association name. The type/format of this object is determined by the value of the rcDot1agCfmMaNetNameType object. This name must be unique within a maintenance domain.	IEEE8021-CFM-MIBDot1agCfmMaintAssocNamer/w Type Constraints: range: 1..45	.1.3.6.1.4.1.8886.6.1.32.1.6.1.1.3
rcDot1agCfmMaNetCcmInterval Interval between CCM transmissions to be used by all MEPs in the MA.	IEEE8021-CFM-MIBDot1agCfmCcmIntervalr/w Type Values: 0 intervalInvalid 1 interval300Hz 2 interval10ms 3 interval100ms 4 interval1s 5 interval10s 6 interval1min 7 interval10min	.1.3.6.1.4.1.8886.6.1.32.1.6.1.1.4
rcDot1agCfmMaNetRowStatus The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.6.1.1.5

The Maintenance Association table.  Each row in the table
represents an MA.  An MA is a set of MEPs, each configured
with a single service instance.
          
This is the part of the complete MA table that is variable
across the Bridges in a Maintenance Domain, or across the
components of a single Bridge.  That part of the MA table that
is constant across the Bridges and their components in a
Maintenance Domain is contained in the rcDot1agCfmMaNetTable.
          
This table uses three indices, first index is the
rcDot1agCfmPbbComponentIdentifier that identifies the component
within the Bridge for which the information in the
rcDot1agCfmMaCompEntry applies.  The second is the index of the
Maintenance Domain table.  The third index is the same as the
index of the rcDot1agCfmMaNetEntry for the same MA.
          
The writable objects in this table need to be persistent
upon reboot or restart of a device.

rcDot1agCfmMaCompEntry row .1.3.6.1.4.1.8886.6.1.32.1.6.2.1

The MA table entry.

Indexes

rcDot1agCfmMaComponentId rcDot1agCfmMdIndex rcDot1agCfmMaIndex

Column	Syntax	OID
rcDot1agCfmMaComponentId The bridge component within the system to which the information in this rcDot1agCfmMaCompEntry applies. If the system is not a Bridge, or if only one component is present in the Bridge, then this variable (index) must …	IEEE8021-CFM-MIBDot1agCfmPbbComponentIdentifier Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.1
rcDot1agCfmMaCompPrimaryVlanId The Primary VLAN ID with which the Maintenance Association is associated, or 0 if the MA is not attached to any VID. If the MA is associated with more than one VID, the rcDot1agCfmVlanTable lists them.	Q-BRIDGE-MIBVlanIdOrNoner/w Type Constraints: range: 0..4094	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.2
rcDot1agCfmMaCompMhfCreation Indicates if the Management entity can create MHFs (MIP Half Function) for this MA.	IEEE8021-CFM-MIBDot1agCfmMhfCreationr/w Type Values: 1 defMHFnone 2 defMHFdefault 3 defMHFexplicit 4 defMHFdefer	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.3
rcDot1agCfmMaCompIdPermission Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this MA.	IEEE8021-CFM-MIBDot1agCfmIdPermissionr/w Type Values: 1 sendIdNone 2 sendIdChassis 3 sendIdManage 4 sendIdChassisManage 5 sendIdDefer	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.4
rcDot1agCfmMaCompNumberOfVids The number of VIDs associated with the MA.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.5
rcDot1agCfmMaCompRowStatus The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.6.2.1.6

List of MEPIDs that belong to this MA.
          
Clause 12.14.6.1.3 specifies that a list of MEPIDs in all
bridges in that MA, but since SNMP SMI does not allow to
state in a MIB that an object in a table is an array, the 
information has to be stored in another table with two
indices, being the first index, the index of the table that 
contains the list or array.
          
For all bridges in which the same MAID {rcDot1agCfmMdFormat,
rcDot1agCfmMdName, rcDot1agCfmMaNetFormat, and rcDot1agCfmMaNetName}
is configured, the same set of rcDot1agCfmMaMepListIdentifiers
must be configured in the bridges' rcDot1agCfmMaMepListTables.
This allows each MEP to determine whether or not it is
receiving CCMs from all of the other MEPs in the MA.
          
For example, if one were creating a new MA whose MAID were
{charString, 'Dom1', charString, 'MA1'}, that had 2 MEPs, whose
MEPIDs were 1 and 3, one could, in Bridge A:
 1. Get a new MD index d from rcDot1agCfmMdTableNextIndex.
 2. Create the Maintenance Domain {charString, 'Dom1'}.
 3. Get a new MA index a from rcDot1agCfmMdMaNextIndex [d].
 4. Create the Maintenance Association {charString, 'MA1'}.
 5. Create a new rcDot1agCfmMaMepListEntry for each of the MEPs
    in the MA: [d, a, 1] and [d, a, 3].
 6. Create one of the new MEPs, say [d, a, 1].
Then, in Bridge B:
 7. Do all of these steps 1-6, except for using the other MEPID
    for the new MEP in Step 6, in this example, MEPID 3.
Note that, when creating the MA, MEP List Table, and MEP
entries in the second bridge, the indices 'd' and 'a'
identifying the MAID {charString, 'Dom1', charString, 'MA1'}
may have different values than those in the first Bridge.

rcDot1agCfmMaMepListEntry row .1.3.6.1.4.1.8886.6.1.32.1.6.3.1

The known MEPS table entry.

Indexes

rcDot1agCfmMdIndex rcDot1agCfmMaIndex rcDot1agCfmMaMepListIdentifier

Column	Syntax	OID
rcDot1agCfmMaMepListIdentifier MEPID	IEEE8021-CFM-MIBDot1agCfmMepId Type Constraints: range: 1..8191	.1.3.6.1.4.1.8886.6.1.32.1.6.3.1.1
rcDot1agCfmMaMepListRowStatus The status of the row. Read SNMPv2-TC (RFC1903) for an explanation of the possible values this object can take.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.6.3.1.2

The Maintenance Association End Point (MEP) table.
          
Each row in the table represents a different MEP.  A MEP is
an actively managed CFM entity, associated with a specific
DSAP of a Service Instance, which can generate and receive
CFM PDUs and track any responses.  It is an end point of a
single Maintenance Association, and is an endpoint of a
separate Maintenance Entity for each of the other MEPs in
the same Maintenance Association (802.1ag clause 3.17).
          
This table uses three indices. The first two indices are the
indices of the Maintenance Domain and MA tables, the reason
being that a MEP is always related to an MA and Maintenance
Domain.
          
The MEP table also stores all the managed objects for sending
LBM and LTM.
          
*LBM Managed objects
          
LBM Managed objects in the MEP table 
enables the management entity to initiate
transmission of Loopback messages.  It will signal the MEP
that it should transmit some number of Loopback messages
and detect the detection (or lack thereof) of the
corresponding Loopback messages.
          
Steps to use entries in this table:
          
1) Wait for rcDot1agCfmMepTransmitLbmStatus value to be
   true.  To do this do this sequence:
   a. an SNMP GET for both SnmpSetSerialNo and
      rcDot1agCfmMepTransmitLbmStatus objects (in same SNMP
      PDU).
   b. Check if value for rcDot1agCfmMepTransmitLbmStatus is true.
      - if not, wait x seconds, go to step a above.
      - if yes, save the value of SnmpSetSerialNo and go
        to step 2) below
2) Change rcDot1agCfmMepTransmitLbmStatus value from true to
   false to ensure no other management entity will use
   the service. In order to not disturb a possible other NMS
   do this by sending an SNMP SET for both SnmpSetSerialNo 
   and rcDot1agCfmMepTransmitLbmStatus objects (in same SNMP
   PDU,  and make sure SNmpSetSerialNo is the first varBind).
   For the SnmpSetSerialNo varBind, use the value that you
   obtained in step 1)a.. This ensures that two cooperating
   NMSes will not step on each others toes.
3) Setup the different data to be sent (number of messages,
   optional TLVs,...), except do not set
   rcDot1agCfmMepTransmitLbmMessages.
4) Record the current values of rcDot1agCfmMepLbrIn,
   rcDot1agCfmMepLbrInOutOfOrder, and rcDot1agCfmMepLbrBadMsdu.
6) Set rcDot1agCfmMepTransmitLbmMessages to a non-zero value to
   initiate transmission of Loopback messages.
7) Check the value of rcDot1agCfmMepTransmitLbmResultOK to
   find out if the operation was successfully initiated or
   not.
8) Monitor the value of rcDot1agCfmMepTransmitLbmMessages.
   When it reaches 0, the last LBM has been transmitted.
   Wait an additional 5 seconds to ensure that all LBRs have
   been returned.
9) Compare rcDot1agCfmMepLbrIn, rcDot1agCfmMepLbrInOutOfOrder,
   and rcDot1agCfmMepLbrBadMsdu to their old values from step
   4, above, to get the results of the test.
10) Change the rcDot1agCfmMepTransmitLbmStatus value back to
   true to allow other management entities to use the table.
          
*LTM Managed objects
The LTM Managed objects in the MEP table are used in a manner
similar to that described for LBM transmission, above, except
transmission is initiated by writing a value to the
rcDot1agCfmMepTransmitLtmFlags object.  Upon
successfully initiating the transmission, the variables
rcDot1agCfmMepTransmitLtmSeqNumber and
rcDot1agCfmMepTransmitLtmEgressIdentifier return the information
required to recover the results of the LTM from the
rcDot1agCfmLtrTable.

rcDot1agCfmMepEntry row .1.3.6.1.4.1.8886.6.1.32.1.7.1.1

The MEP table entry

Indexes

rcDot1agCfmMdIndex rcDot1agCfmMaIndex rcDot1agCfmMepIdentifier

Column	Syntax	OID
rcDot1agCfmMepIdentifier Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.18). …	IEEE8021-CFM-MIBDot1agCfmMepId Type Constraints: range: 1..8191	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.1
rcDot1agCfmMepIfIndex This object is the interface index of the interface either a bridge port, or an aggregated IEEE 802.1 link within a bridge port, to which the MEP is attached. Upon a restart of the system, the system SHAL…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.2
rcDot1agCfmMepDirection The direction in which the MEP faces on the Bridge port.	IEEE8021-CFM-MIBDot1agCfmMpDirectionr/w Type Values: 1 down 2 up	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.3
rcDot1agCfmMepPrimaryVid An integer indicating the Primary VID of the MEP, always one of the VIDs assigned to the MEP's MA. The value 0 indicates that either the Primary VID is that of the MEP's MA, or that the MEP's MA is associated with no V…	Unsigned32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.4
rcDot1agCfmMepActive Administrative state of the MEP A Boolean indicating the administrative state of the MEP. True indicates that the MEP is to function normally, and false that it is to cease functioning.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.5
rcDot1agCfmMepFngState Current state of the MEP Fault Notification Generator State Machine.	IEEE8021-CFM-MIBDot1agCfmFngState Type Values: 1 fngReset 2 fngDefect 3 fngReportDefect 4 fngDefectReported 5 fngDefectClearing	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.6
rcDot1agCfmMepCciEnabled If set to true, the MEP will generate CCM messages.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.7
rcDot1agCfmMepCcmLtmPriority The priority value for CCMs and LTMs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default va…	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.8
rcDot1agCfmMepMacAddress MAC address of the MEP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.9
rcDot1agCfmMepLowPrDef An integer value specifying the lowest priority defect that is allowed to generate fault alarm.	IEEE8021-CFM-MIBDot1agCfmLowestAlarmPrir/w Type Values: 1 allDef 2 macRemErrXcon 3 remErrXcon 4 errXcon 5 xcon 6 noXcon	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.10
rcDot1agCfmMepFngAlarmTime The time that defects must be present before a Fault Alarm is issued (fngAlarmTime. 20.33.3) (default 2.5s).	Integer32r/w Constraints: range: 250-1000	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.11
rcDot1agCfmMepFngResetTime The time that defects must be absent before resetting a Fault Alarm (fngResetTime, 20.33.4) (default 10s).	Integer32r/w Constraints: range: 250-1000	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.12
rcDot1agCfmMepHighestPrDefect The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state.	IEEE8021-CFM-MIBDot1agCfmHighestDefectPri Type Values: 0 none 1 defRDICCM 2 defMACstatus 3 defRemoteCCM 4 defErrorCCM 5 defXconCCM	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.13
rcDot1agCfmMepDefects A vector of Boolean error conditions from Table 20-1, any of which may be true: DefRDICCM(0) DefMACstatus(1) DefRemoteCCM(2) DefErrorCCM(3) DefXconCCM(4)	IEEE8021-CFM-MIBDot1agCfmMepDefects Type Values: 0 bDefRDICCM 1 bDefMACstatus 2 bDefRemoteCCM 3 bDefErrorCCM 4 bDefXconCCM	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.14
rcDot1agCfmMepErrorCcmLastFailure The last-received CCM that triggered an DefErrorCCM fault.	OctetString Constraints: range: 1-1522	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.15
rcDot1agCfmMepXconCcmLastFailure The last-received CCM that triggered a DefXconCCM fault.	OctetString Constraints: range: 1-1522	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.16
rcDot1agCfmMepCcmSequenceErrors The total number of out-of-sequence CCMs received from all remote MEPs.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.17
rcDot1agCfmMepCciSentCcms Total number of Continuity Check messages transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.18
rcDot1agCfmMepNextLbmTransId Next sequence number/transaction identifier to be sent in a Loopback message. This sequence number can be zero because it wraps around.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.19
rcDot1agCfmMepLbrIn Total number of valid, in-order Loopback Replies received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.20
rcDot1agCfmMepLbrInOutOfOrder The total number of valid, out-of-order Loopback Replies received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.21
rcDot1agCfmMepLbrBadMsdu The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.22
rcDot1agCfmMepLtmNextSeqNumber Next transaction identifier/sequence number to be sent in a Linktrace message. This sequence number can be zero because it wraps around.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.23
rcDot1agCfmMepUnexpLtrIn The total number of unexpected LTRs received (20.39.1).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.24
rcDot1agCfmMepLbrOut Total number of Loopback Replies transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.25
rcDot1agCfmMepTransmitLbmStatus A Boolean flag set to true by the bridge port to indicate that another LBM may be transmitted.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.26
rcDot1agCfmMepTransmitLbmDestMacAddress The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column rcDot1agCfmMepTransmitLbmDestIsMepId is 'false'.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.27
rcDot1agCfmMepTransmitLbmDestMepId The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the column rcDot1agCfmMepTransmitLbmDestIsMep…	IEEE8021-CFM-MIBDot1agCfmMepIdOrZeror/w Type Constraints: range: 0..8191	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.28
rcDot1agCfmMepTransmitLbmDestIsMepId True indicates that MEPID of the target MEP is used for Loopback transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.29
rcDot1agCfmMepTransmitLbmMessages The number of Loopback messages to be transmitted.	Integer32r/w Constraints: range: 1-1024	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.30
rcDot1agCfmMepTransmitLbmDataTlv An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent.	OctetStringr/w Constraints: range: 0-1500	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.31
rcDot1agCfmMepTransmitLbmVlanPriority Priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.32
rcDot1agCfmMepTransmitLbmVlanDropEnable Drop Enable bit value to be used in the VLAN tag, if present in the transmitted frame. For more information about VLAN Drop Enable, please check IEEE 802.1ad.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.33
rcDot1agCfmMepTransmitLbmResultOK Indicates the result of the operation: - true The Loopback Message(s) will be (or has been) sent. - false The Loopback Message(s) will not be sent.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.34
rcDot1agCfmMepTransmitLbmSeqNumber The Loopback Transaction Identifier (rcDot1agCfmMepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if rcDot1agCfmMepTransmitLbmResultOK is false.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.35
rcDot1agCfmMepTransmitLtmStatus A Boolean flag set to true by the bridge port to indicate that another LTM may be transmitted. Reset to false by the MEP Linktrace Initiator State Machine.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.36
rcDot1agCfmMepTransmitLtmFlags The flags field for LTMs transmitted by the MEP.	Bitsr/w Enumerated Values: 0 useFDBonly	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.37
rcDot1agCfmMepTransmitLtmTargetMacAddress The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column rcDot1agCfmMepTransmitLtmTargetIsMepId is 'false'.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.38
rcDot1agCfmMepTransmitLtmTargetMepId An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address will be used if the value of the column r…	IEEE8021-CFM-MIBDot1agCfmMepIdOrZeror/w Type Constraints: range: 0..8191	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.39
rcDot1agCfmMepTransmitLtmTargetIsMepId True indicates that MEPID of the target MEP is used for Linktrace transmission. False indicates that unicast destination MAC address of the target MEP is used for Loopback transmission.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.40
rcDot1agCfmMepTransmitLtmTtl The LTM TTL field. Default value, if not specified, is 64. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each Linktrace Responder that handles the LTM. The value returned in the …	Unsigned32r/w Constraints: range: 0-255	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.41
rcDot1agCfmMepTransmitLtmResult Indicates the result of the operation: - true The Linktrace Message will be (or has been) sent. - false The Linktrace Message will not be sent	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.42
rcDot1agCfmMepTransmitLtmSeqNumber The LTM Transaction Identifier (rcDot1agCfmMepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if rcDot1agCfmMepTransmitLtmResult is false.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.43
rcDot1agCfmMepTransmitLtmEgressIdentifier Identifies the MEP Linktrace Initiator that is originating, or the Linktrace Responder that is forwarding, this LTM. The low-order six octets contain a 48-bit IEEE MAC address unique to the system in which the MEP Linkt…	OctetStringr/w Constraints: range: 8-8	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.44
rcDot1agCfmMepRowStatus The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.32.1.7.1.1.45

This table extends the MEP table and contains a list of
Linktrace replies received by a specific MEP in response to
a linktrace message.
          
SNMP SMI does not allow to state in a MIB that an object in
a table is an array.  The solution is to take the index (or
indices) of the first table and add one or more indices.

rcDot1agCfmLtrEntry row .1.3.6.1.4.1.8886.6.1.32.1.7.2.1

The Linktrace Reply table entry.

Indexes

rcDot1agCfmMdIndex rcDot1agCfmMaIndex rcDot1agCfmMepIdentifier rcDot1agCfmLtrSeqNumber rcDot1agCfmLtrReceiveOrder

Column	Syntax	OID
rcDot1agCfmLtrSeqNumber Transaction identifier/Sequence number returned by a previous transmit linktrace message command, indicating which LTM's response is going to be returned.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.1
rcDot1agCfmLtrReceiveOrder An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. rcDot1agCfmLtrReceiveOrder are assigned sequentially from 1, in the order that the Linktrace Initiator received the LTRs.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.2
rcDot1agCfmLtrTtl TTL field value for a returned LTR.	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.3
rcDot1agCfmLtrForwarded Indicates if a LTM was forwarded by the responding MP, as returned in the 'FwdYes' flag of the flags field.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.4
rcDot1agCfmLtrTerminalMep A boolean value stating whether the forwarded LTM reached a MEP enclosing its MA, as returned in the Terminal MEP flag of the Flags field.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.5
rcDot1agCfmLtrLastEgressIdentifier An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP Linktrace Initiator that originated, or the Linktrace Responder that…	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.6
rcDot1agCfmLtrNextEgressIdentifier An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the Linktrace Responder that transmitted this LTR, and can forward the LTM t…	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.7
rcDot1agCfmLtrRelay Value returned in the Relay Action field.	IEEE8021-CFM-MIBDot1agCfmRelayActionFieldValue Type Values: 1 rlyHit 2 rlyFdb 3 rlyMpdb	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.8
rcDot1agCfmLtrChassisIdSubtype This object specifies the format of the Chassis ID returned in the Sender ID TLV of the LTR, if any. This value is meaningless if the rcDot1agCfmLtrChassisId has a length of 0.	LLDP-MIBLldpChassisIdSubtype Type Values: 1 chassisComponent 2 interfaceAlias 3 portComponent 4 macAddress 5 networkAddress 6 interfaceName 7 local	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.9
rcDot1agCfmLtrChassisId The Chassis ID returned in the Sender ID TLV of the LTR, if any. The format of this object is determined by the value of the rcDot1agCfmLtrChassisIdSubtype object.	LLDP-MIBLldpChassisId Type Constraints: range: 1..255	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.10
rcDot1agCfmLtrManAddressDomain The TDomain that identifies the type and format of the related rcDot1agCfmMepDbManAddress object, used to access the SNMP agent of the system transmitting the LTR. Received in the LTR Sender ID TLV from that system. …	SNMPv2-TCTDomain Description: Denotes a kind of transport service. Some possible values, such as snmpUDPDomain, are defined in the SNMPv2-TM MIB module. Other possible values are defined in other MIB modules.	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.11
rcDot1agCfmLtrManAddress The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object rcDot1agCfmLtrManAddressDomain contains…	SNMPv2-TCTAddress Type Constraints: range: 1..255 Description: Denotes a transport service address. A TAddress value is always interpreted within the context of a TDomain value. Thus, each definition of a TDomain value must be accompanied by a definition of a textual co…	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.12
rcDot1agCfmLtrIngress The value returned in the Ingress Action Field of the LTM. The value ingNoTlv(0) indicates that no Reply Ingress TLV was returned in the LTM.	IEEE8021-CFM-MIBDot1agCfmIngressActionFieldValue Type Values: 0 ingNoTlv 1 ingOk 2 ingDown 3 ingBlocked 4 ingVid	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.13
rcDot1agCfmLtrIngressMac MAC address returned in the ingress MAC address field. If the rcDot1agCfmLtrIngress object contains the value ingNoTlv(0), then the contents of this object are meaningless.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.14
rcDot1agCfmLtrIngressPortIdSubtype Format of the Ingress Port ID. If the rcDot1agCfmLtrIngress object contains the value ingNoTlv(0), then the contents of this object are meaningless.	LLDP-MIBLldpPortIdSubtype Type Values: 1 interfaceAlias 2 portComponent 3 macAddress 4 networkAddress 5 interfaceName 6 agentCircuitId 7 local	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.15
rcDot1agCfmLtrIngressPortId Ingress Port ID. The format of this object is determined by the value of the rcDot1agCfmLtrIngressPortIdSubtype object. If the rcDot1agCfmLtrIngress object contains the value ingNoTlv(0), then the contents of this objec…	LLDP-MIBLldpPortId Type Constraints: range: 1..255	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.16
rcDot1agCfmLtrEgress The value returned in the Egress Action Field of the LTM. The value egrNoTlv(0) indicates that no Reply Egress TLV was returned in the LTM.	IEEE8021-CFM-MIBDot1agCfmEgressActionFieldValue Type Values: 0 egrNoTlv 1 egrOK 2 egrDown 3 egrBlocked 4 egrVid	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.17
rcDot1agCfmLtrEgressMac MAC address returned in the egress MAC address field. If the rcDot1agCfmLtrEgress object contains the value egrNoTlv(0), then the contents of this object are meaningless.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.18
rcDot1agCfmLtrEgressPortIdSubtype Format of the egress Port ID. If the rcDot1agCfmLtrEgress object contains the value egrNoTlv(0), then the contents of this object are meaningless.	LLDP-MIBLldpPortIdSubtype Type Values: 1 interfaceAlias 2 portComponent 3 macAddress 4 networkAddress 5 interfaceName 6 agentCircuitId 7 local	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.19
rcDot1agCfmLtrEgressPortId Egress Port ID. The format of this object is determined by the value of the rcDot1agCfmLtrEgressPortIdSubtype object. If the rcDot1agCfmLtrEgress object contains the value egrNoTlv(0), then the contents of this object a…	LLDP-MIBLldpPortId Type Constraints: range: 1..255	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.20
rcDot1agCfmLtrOrganizationSpecificTlv All Organization specific TLVs returned in the LTR, if any. Includes all octets including and following the TLV Length field of each TLV, concatenated together.	OctetString Constraints: range: 4-1500 range: 0-0	.1.3.6.1.4.1.8886.6.1.32.1.7.2.1.21

The MEP Database. A database, maintained by every MEP, that
maintains received information about other MEPs in the
Maintenance Domain.
          
The SMI does not allow to state in a MIB that an object in
a table is an array. The solution is to take the index (or
indices) of the first table and add one or more indices.

rcDot1agCfmMepDbEntry row .1.3.6.1.4.1.8886.6.1.32.1.7.3.1

The MEP Database table entry.

Indexes

rcDot1agCfmMdIndex rcDot1agCfmMaIndex rcDot1agCfmMepIdentifier rcDot1agCfmMepDbRMepIdentifier

Column	Syntax	OID
rcDot1agCfmMepDbRMepIdentifier Maintenance association End Point Identifier of a remote MEP whose information from the MEP Database is to be returned.	IEEE8021-CFM-MIBDot1agCfmMepId Type Constraints: range: 1..8191	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.1
rcDot1agCfmMepDbRMepState The operational state of the remote MEP IFF State machines.	IEEE8021-CFM-MIBDot1agCfmRemoteMepState Type Values: 1 rMepIdle 2 rMepStart 3 rMepFailed 4 rMepOk	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.2
rcDot1agCfmMepDbRMepFailedOkTime The time (SysUpTime) at which the IFF Remote MEP state machine last entered either the RMEP_FAILED or RMEP_OK state.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.3
rcDot1agCfmMepDbMacAddress The MAC address of the remote MEP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.4
rcDot1agCfmMepDbRdi State of the RDI bit in the last received CCM (true for RDI=1), or false if none has been received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.5
rcDot1agCfmMepDbPortStatusTlv An enumerated value of the Port status TLV received in the last CCM from the remote MEP or the default value psNoPortStateTLV indicating either no CCM has been received, or that nor port status TLV was received in the l…	IEEE8021-CFM-MIBDot1agCfmPortStatus Type Values: 0 psNoPortStateTLV 1 psBlocked 2 psUp	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.6
rcDot1agCfmMepDbInterfaceStatusTlv An enumerated value of the Interface status TLV received in the last CCM from the remote MEP or the default value isNoInterfaceStatus TLV indicating either no CCM has been received, or that no interface status TLV was r…	IEEE8021-CFM-MIBDot1agCfmInterfaceStatus Type Values: 0 isNoInterfaceStatusTLV 1 isUp 2 isDown 3 isTesting 4 isUnknown 5 isDormant 6 isNotPresent 7 isLowerLayerDown	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.7
rcDot1agCfmMepDbChassisIdSubtype This object specifies the format of the Chassis ID received in the last CCM.	LLDP-MIBLldpChassisIdSubtype Type Values: 1 chassisComponent 2 interfaceAlias 3 portComponent 4 macAddress 5 networkAddress 6 interfaceName 7 local	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.8
rcDot1agCfmMepDbChassisId The Chassis ID. The format of this object is determined by the value of the rcDot1agCfmLtrChassisIdSubtype object.	LLDP-MIBLldpChassisId Type Constraints: range: 1..255	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.9
rcDot1agCfmMepDbManAddressDomain The TDomain that identifies the type and format of the related rcDot1agCfmMepDbManAddress object, used to access the SNMP agent of the system transmitting the CCM. Received in the CCM Sender ID TLV from that system. …	SNMPv2-TCTDomain Description: Denotes a kind of transport service. Some possible values, such as snmpUDPDomain, are defined in the SNMPv2-TM MIB module. Other possible values are defined in other MIB modules.	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.10
rcDot1agCfmMepDbManAddress The TAddress that can be used to access the SNMP agent of the system transmitting the CCM, received in the CCM Sender ID TLV from that system. If the related object rcDot1agCfmMepDbManAddressDomain contai…	SNMPv2-TCTAddress Type Constraints: range: 1..255 Description: Denotes a transport service address. A TAddress value is always interpreted within the context of a TDomain value. Thus, each definition of a TDomain value must be accompanied by a definition of a textual co…	.1.3.6.1.4.1.8886.6.1.32.1.7.3.1.11