RADWARE-MIB Table View

The community table of the agent

rndCommunityEntry row .1.3.6.1.4.1.89.2.7.2.1

The row definition for this table.

Indexes

rndCommunityMngStationAddr rndCommunityString

Column	Syntax	OID
rndCommunityMngStationAddrmandatory The management station that will be allowed to communicate with the agent IP address	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.2.7.2.1.1
rndCommunityStringmandatory The community string with which the management station will communicate with the agent	OctetStringr/w Constraints: range: 1-20	.1.3.6.1.4.1.89.2.7.2.1.2
rndCommunityAccessmandatory The allowed access to this management station	Enumerationr/w Enumerated Values: 1 readOnly 2 readWrite 3 super	.1.3.6.1.4.1.89.2.7.2.1.3
rndCommunityTrapsEnablemandatory Should the agent send traps to the management station	Enumerationr/w Enumerated Values: 1 trapsEnable 2 trapsDisable	.1.3.6.1.4.1.89.2.7.2.1.4
rndCommunityStatusmandatory The status of this entry. If the status is invalid the community entry will be deleted	Enumerationr/w Enumerated Values: 1 enable 2 invalid	.1.3.6.1.4.1.89.2.7.2.1.5

RND-specific interface table.  Each table entry includes an
index, Board number, Network Address, interface status, clock
indicator and interface cost.

rndIfEntry row .1.3.6.1.4.1.89.4.1.1

The row definition for this table.

Indexes

rndIfIndex

Column	Syntax	OID
rndIfIndexmandatory Index to the RND Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII).	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.4.1.1.1
rndIfBoardNummandatory The interface defined by this entry correspTnds to the board defined by the same value of rndSlotBoardNum in the rndSlotTab.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.4.1.1.2
rndIfNetAddressmandatory The IP address of the interface defined by the particular value of rndIfIndex.	RFC1155-SMINetworkAddress	.1.3.6.1.4.1.89.4.1.1.3
rndIfStatusmandatory The current status of the interface.	Enumeration Enumerated Values: 1 ok 2 okSingleBrg 3 okMultiBrg 4 connctFault 5 rxFault 6 txFault 7 channelLoopback 8 rxClockFault 9 t1Alarm	.1.3.6.1.4.1.89.4.1.1.4
rndIfClockTypemandatory rndIfClockType defines the type of clock each interface uses: internal or external.	Enumerationr/w Enumerated Values: 1 external 2 internal 3 t1 4 g703	.1.3.6.1.4.1.89.4.1.1.5
rndIfBaudRatemandatory Defines the baud rate of use by the interface. The valid rates are determined by the type of the media for which this baud rate is defined.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.4.1.1.6
rndIfCostmandatory This variable assigns a transmission cost to the interface (channel or LAN). These costs are used in Level II routing. The costs aretypically inversly proportional to the channel quality.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.4.1.1.7
rndIfCompressionmandatory Defines whether data compression is enabled or disabled for the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.4.1.1.8
rndIfCompressionStatusmandatory Defines the status of the compression component: not-inserted - Compression component is not in the device active - Compression is enabled and operates correctly not-active - Compression is enables but does not oper…	Enumeration Enumerated Values: 1 not-inserted 2 active 3 not-active 4 disable	.1.3.6.1.4.1.89.4.1.1.9
rndIfCompressionRatemandatory Percentage of compression. This variable applies only if rndCompressionStatus is active.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.4.1.1.10
rndIfLATCompressionmandatory Enable/Disable the LAT Compression.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.4.1.1.11
rndIfCompressionTypemandatory This parameter indicates the type of compression option available in the device. none(1) - indicates that there is no compression option in the device lowSpeed(2) - indicates a compression option which is operation…	Enumeration Enumerated Values: 1 none 2 lowSpeed 3 highSpeed	.1.3.6.1.4.1.89.4.1.1.12
rndIfFilterModemandatory This parameter indicates the type of filtering in the device.	Enumerationr/w Enumerated Values: 1 destinationOnly 2 sourceAndDestination 3 none	.1.3.6.1.4.1.89.4.1.1.13
rndIfChannelTypemandatory The type of the WAN channel	Enumerationr/w Enumerated Values: 1 wanChannel 2 ogRanPort 3 routerToBridge 4 spsFramRelay 5 dialBackup 6 snar 7 lan 8 spsX25 9 frameRelay1490 10 frameRelay1490CAR 11 frameRelayCAR 12 ppp	.1.3.6.1.4.1.89.4.1.1.14
rndIfBridgemandatory This variable indicates whether this interface forward Layer II pakages.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.4.1.1.15
rndHighPriorityIfmandatory This variable indicates whether this interface will forward pakages that fit HighPriority set by the manager.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.4.1.1.16
rndWanHeadermandatory This variable indicates the RND WAN header type used for frames which pass through this interface. 'regular' specifies a 14 bytes header compatible with older OG versions and 'short' a 4 byte header compatible with the …	Enumerationr/w Enumerated Values: 1 regular 2 short	.1.3.6.1.4.1.89.4.1.1.17
rndDuplexModemandatory This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode.	Enumerationr/w Enumerated Values: 1 half 2 full	.1.3.6.1.4.1.89.4.1.1.18

The table of  FACS action.

rndFACSActEntry row .1.3.6.1.4.1.89.16.2.1

Each rndFACSActEntry consist of the following parameters

Indexes

rndFACSActType rndFACSActIfIndex

Column	Syntax	OID
rndFACSActTypemandatory This parameter indicate on which FACS Table the FACS action will preform.	Enumeration Enumerated Values: 1 tx 2 rx 4 activeDB 5 tempDB	.1.3.6.1.4.1.89.16.2.1.1
rndFACSActIfIndexmandatory The interface to which this FACS entry is applicable.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.2.1.2
rndFACSActionmandatory The management station that sends a SET request for one of these actions with indexes rndFACSType and rndFACSIfIndex defines the type and the interface Id for which all FACS statements are to be erased. If no interfac…	Enumerationr/w Enumerated Values: 1 none 2 eraseIP 3 eraseDECnet 4 eraseIPX 5 eraseBrg 6 replaceIP 8 replaceIPX 9 replaceBrg 10 backupIP 12 backupIPX 13 backupBrg	.1.3.6.1.4.1.89.16.2.1.3

The table of  FACS statment.

rndFACSEntry row .1.3.6.1.4.1.89.16.3.1

Each FACS statment consist of the following parameters

Indexes

rndFACSIfIndex rndFACSProtocolType rndFACSType rndFACSIndex

Column	Syntax	OID
rndFACSIfIndexmandatory The interface to which this FACS entry is applicable.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.3.1.1
rndFACSProtocolTypemandatory This parameter define the protocol the Security Access Control is applicable.	Enumeration Enumerated Values: 1 ip 2 ipx 3 dec 4 bridge	.1.3.6.1.4.1.89.16.3.1.2
rndFACSTypemandatory The Mode of in which this FACS statement operates.	Enumeration Enumerated Values: 1 tx 2 rx 3 cod 4 activeDB 5 tempDB	.1.3.6.1.4.1.89.16.3.1.3
rndFACSIndexmandatory Index to the FACS Table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.3.1.4
rndFACSSrcAddmandatory The size of the octet string will be according to the protocol type define in rndFACSProtocolType.	OctetStringr/w	.1.3.6.1.4.1.89.16.3.1.5
rndFACSSrcAddMaskmandatory Source-address mask .	OctetStringr/w	.1.3.6.1.4.1.89.16.3.1.6
rndFACSDesAddmandatory Destination-address The size of the octet string will be according to the protocol type define in rndFACSProtocolType .	OctetStringr/w	.1.3.6.1.4.1.89.16.3.1.7
rndFACSDesAddMaskmandatory Destination-address mask .	OctetStringr/w	.1.3.6.1.4.1.89.16.3.1.8
rndFACSOperationmandatory ... .	Enumerationr/w Enumerated Values: 1 block 2 forward 3 permit 4 deny 5 blockZHRP 129 blockAndReport	.1.3.6.1.4.1.89.16.3.1.9
rndFACSNetFilteringmandatory ... .	Enumerationr/w Enumerated Values: 1 none 2 l2multicast 3 arp 4 icmp 5 ip 6 udp 7 tcp 8 decnet 9 ipx	.1.3.6.1.4.1.89.16.3.1.10
rndFACSSoketNummandatory Port/socket number for different applications 0 is default meaning not applicable.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.3.1.11
rndFACSMask1Idmandatory Index into RND mask table FACS/COD Type) .	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.3.1.12
rndFACSMask2Idmandatory Index into RND mask table FACS/COD according to the value of rndFACSType .	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.16.3.1.13
rndFACSStatusmandatory The status of a table entry.	Enumerationr/w Enumerated Values: 1 valid 2 createRequest 3 underCreation 4 invalid	.1.3.6.1.4.1.89.16.3.1.14

This table is parralel to MIB II IpAddrTable, and is used to
add/delete entries to/from that table. In addition it contains
private objects.

rsIpAddrEntry row .1.3.6.1.4.1.89.26.1.1

The addressing information for one of this
entity's IP addresses.

Indexes

rsIpAdEntAddr

Column	Syntax	OID
rsIpAdEntAddrmandatory The IP address to which this entry's addressing information pertains.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.1.1.1
rsIpAdEntIfIndexmandatory The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.1.1.2
rsIpAdEntNetMaskmandatory The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.1.1.3
rsIpAdEntForwardIpBroadcastmandatory This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.1.1.4
rsIpAdEntReasmMaxSizemandatory The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.89.26.1.1.5
rsIpAdEntStatusmandatory The validity of this entry. Invalid indicates that this entry is invalid in IpAddrTable (MIB II).	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.89.26.1.1.6
rsIpAdEntBcastAddrmandatory Indicates how the host part of ip subnet broadcast messages will be filled: 0 - host part will be filled by 0 1 - host part will be filled by 1.	Integer32r/w Constraints: range: 0-1	.1.3.6.1.4.1.89.26.1.1.7
rsIpAdEntVlanTagmandatory The vlan Tag value that represent this ip interface this filed include both vlna tag and vlan priority	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.1.1.8
rsIpAdEntOneIpModemandatory the one-ip mode. Relevant only for LinkProof devices. disable - regular interface. Enable - the specific ip can be ip-to-me (to device) and/or forwarding ip	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.1.1.9
rsIpAdEntTypemandatory Ip interface type. The way the ip-interface was set determine its type	Enumeration Enumerated Values: 1 static 2 dhcp 3 pppoe 4 pptp	.1.3.6.1.4.1.89.26.1.1.10
rsIpAdEntPeerAddrmandatory IP of same interface on the peer device.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.1.1.11
rsIpAdEntPeerAddrStatusmandatory Indicating the relevancy of PeerAddr for this row	Enumerationr/w Enumerated Values: 1 relevant 2 nonrelevant	.1.3.6.1.4.1.89.26.1.1.12

This table contains ICMP Router Discovery parameters
configurated per IP interface.

rsIcmpRdEntry row .1.3.6.1.4.1.89.26.2.2.1

The ICMP parameters configurated for IP interface.

Indexes

rsIcmpRdIpAddr

Column	Syntax	OID
rsIcmpRdIpAddrmandatory The IP address to which this entry's information pertains.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.2.2.1.1
rsIcmpRdIpAdvertAddrmandatory The IP destination address to be used for multicast Router Advertisements sent from the interface. The only permissible values are the all-systems multicast address, 224.0.0.1, or the limited-broadcast address, 255.255.…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.2.2.1.2
rsIcmpRdMaxAdvertIntervalmandatory The maximum time allowed between sending multicast Router Advertisements from the interface, in seconds. Must be no less than 4 seconds and no greater than 1800 seconds.	Integer32r/w Constraints: range: 4-1800	.1.3.6.1.4.1.89.26.2.2.1.3
rsIcmpRdMinAdvertIntervalmandatory The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface, in seconds. Must be no less than 3 seconds and no greater than rsIcmpRdMaxAdvertInterval. Default: 0.75 * rsIcmpR…	Integer32r/w Constraints: range: 3-1800	.1.3.6.1.4.1.89.26.2.2.1.4
rsIcmpRdAdvertLifetimemandatory The maximum length of time that the advertised addresses are to be considered as valid. Must be no less than rsIcmpRdMaxAdvertInterval and no greater than 9000 seconds. Default: 3 * rsIcmpRdMaxAdvertInterval.	Integer32r/w Constraints: range: 4-9000	.1.3.6.1.4.1.89.26.2.2.1.5
rsIcmpRdAdvertisemandatory A flag indicating whether or not the address is to be advertised.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.2.2.1.6
rsIcmpRdPreferenceLevelmandatory The preferability of the address as a default router address, relative to other router addresses on the same subnet.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.2.2.1.7
rsIcmpRdEntStatusmandatory Setting of any value to this object set values of all fields to the default values.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.2.2.1.8

This table is extension of rip2IfConfTable (RFC 1389 ,RIP 2)

rsRip2IfConfEntry row .1.3.6.1.4.1.89.26.3.1.1

Indexes

rsRip2IfConfAddress

Column	Syntax	OID
rsRip2IfConfAddressmandatory The IP Address of this system on the indicated subnet.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.3.1.1.1
rsRip2IfConfVirtualDismandatory This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.3.1.1.2
rsRip2IfConfAutoSendmandatory This variable controls RIP automatic send behavior. If enabled and no routers were heard on the interface, RIP will only send default route with high metric. Otherwise RIP will send updates according to configuration.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.3.1.1.3

A list of subnets which require separate configuration in RIP. 
This is a combination of rip2IfConfTable and rsRip2IfConfTable.

rdwrRip2IfConfEntry row .1.3.6.1.4.1.89.26.3.2.1

A Single Routing Domain in a single Subnet.

Indexes

rdwrRip2IfConfAddress

Column	Syntax	OID
rdwrRip2IfConfAddressmandatory The IP Address of this system on the indicated subnet. For unnumbered interfaces, the value 0.0.0.N, where the least significant 24 bits (N) is the ifIndex for the IP Interface in network byte order.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.3.2.1.1
rdwrRip2IfConfDomainobsolete Value inserted into the Routing Domain field of all RIP packets sent on this interface.	RouteTagr/w Type Constraints: range: 2	.1.3.6.1.4.1.89.26.3.2.1.2
rdwrRip2IfConfAuthTypemandatory The type of Authentication used on this interface.	Enumerationr/w Enumerated Values: 1 noAuthentication 2 simplePassword	.1.3.6.1.4.1.89.26.3.2.1.3
rdwrRip2IfConfAuthKeymandatory The value to be used as the Authentication Key whenever the corresponding instance of rip2IfConfAuthType has the value simplePassword word. A modification of the corresponding instance of rip2IfConfAuthType does not mo…	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.89.26.3.2.1.4
rdwrRip2IfConfSendmandatory What the router sends on this interface. ripVersion1 implies sending RIP updates compliant with RFC 1058. rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route subsumption rules. ripVersion2 implie…	Enumerationr/w Enumerated Values: 1 doNotSend 2 ripVersion1 3 rip1Compatible 4 ripVersion2 5 ripV1Demand 6 ripV2Demand	.1.3.6.1.4.1.89.26.3.2.1.5
rdwrRip2IfConfReceivemandatory This indicates which version of RIP updates are to be accepted. Note that rip2 and rip1OrRip2 implies reception of multicast packets.	Enumerationr/w Enumerated Values: 1 rip1 2 rip2 3 rip1OrRip2 4 doNotRecieve	.1.3.6.1.4.1.89.26.3.2.1.6
rdwrRip2IfConfDefaultMetricmandatory This variable indicates the metric that is to be used for the default route entry in RIP updates originated on this interface. A value of zero indicates that no default route should be originated; in this case, a defau…	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.89.26.3.2.1.7
rdwrRip2IfConfStatusmandatory Writing invalid has the effect of deleting this interface.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.89.26.3.2.1.8
rdwrRip2IfConfSrcAddressmandatory The IP Address this system will use as a source address on this interface. If it is a numbered interface, this MUST be the same value as rip2IfConfAddress. On unnumbered interfaces, it must be the value of rip2IfConfA…	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.3.2.1.9
rdwrRip2IfConfVirtualDismandatory This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.3.2.1.10
rdwrRip2IfConfAutoSendmandatory This variable controls RIP automatic send behavior. If enabled and no routers were heard on the interface, RIP will only send default route with high metric. Otherwise RIP will send updates according to configuration.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.3.2.1.11

List of IP addresses backed up by this router.

ipRedundRoutersEntry row .1.3.6.1.4.1.89.26.6.3.1

The row definition for this table.

Indexes

ipRedundRoutersIfAddr ipRedundRoutersMainRouterAddr

Column	Syntax	OID
ipRedundRoutersIfAddrmandatory The Ip address of the IP interface on which the redundancy feature is operational.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.6.3.1.1
ipRedundRoutersMainRouterAddrmandatory The Ip address of the polled main router.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.6.3.1.2
ipRedundRoutersOperStatusmandatory If active, the main router is considered inoperational and the IP interface operates as its backup.	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.89.26.6.3.1.3
ipRedundRoutersPollIntervalmandatory Polling interval for this router (in seconds). If 0 the router is not polled.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.6.3.1.4
ipRedundRoutersTimeoutmandatory Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating as backup.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.6.3.1.5
ipRedundRoutersStatusmandatory Entry status	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.26.6.3.1.6

Row holding the device redundancy information.

rdwrRedundancyInfoEntry row .1.3.6.1.4.1.89.26.6.5.1

Row definition for the table.

Indexes

rdwrRedundancyInfoIdx

Column	Syntax	OID
rdwrRedundancyInfoIdxmandatory The entry index. Starting from 1	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.6.5.1.1
rdwrRedundancyInfoInterfacemandatory The entry attached interface	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.6.5.1.2
rdwrRedundancyInfoVRIDmandatory Supporting VRRP, the entry indicates the entry VRID	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.6.5.1.3
rdwrRedundancyInfoModemandatory This variable indicates the IP Redundancy method in the device	Enumeration Enumerated Values: 1 arp 2 not-used 3 vrrp	.1.3.6.1.4.1.89.26.6.5.1.4
rdwrRedundancyInfoMyAddressmandatory The entry indicates the device interfece address	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.6.5.1.5
rdwrRedundancyInfoNeighborAddressmandatory Acting as backup, the entry indicates the master associated address	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.6.5.1.6
rdwrRedundancyInfoStatusmandatory The redundancy entry status	Enumeration Enumerated Values: 1 active 2 backup	.1.3.6.1.4.1.89.26.6.5.1.7

The table of RIP global filters per IP router.

rsIpRipFilterGlbEntry row .1.3.6.1.4.1.89.26.8.1.1

An entry in the RIP global filter table

Indexes

rsIpRipFilterGlbType rsIpRipFilterGlbNumber

Column	Syntax	OID
rsIpRipFilterGlbTypemandatory Type of filter - input/output	Enumeration Enumerated Values: 1 input 2 output	.1.3.6.1.4.1.89.26.8.1.1.1
rsIpRipFilterGlbNumbermandatory Number of RIP filter.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.1.1.2
rsIpRipFilterGlbStatusmandatory The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.	Enumerationr/w Enumerated Values: 1 valid 2 invalid 3 underCreation	.1.3.6.1.4.1.89.26.8.1.1.3
rsIpRipFilterGlbIpAddrmandatory network prefix IP address, as in the forwarding table.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.8.1.1.4
rsIpRipFilterGlbNetworkMaskBitsmandatory the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.1.1.5
rsIpRipFilterGlbMatchBitsmandatory the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this va…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.1.1.6
rsIpRipFilterGlbActionmandatory Filter action - permit/deny for this network	Enumerationr/w Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.89.26.8.1.1.7

Table of input/output  RIP filters used per IP Interface.

rsIpRipFilterLclEntry row .1.3.6.1.4.1.89.26.8.2.1

An entry in the Intf RIP filter table

Indexes

rsIpRipFilterLclIpIntf rsIpRipFilterLclType rsIpRipFilterLclNumber

Column	Syntax	OID
rsIpRipFilterLclIpIntfmandatory The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.26.8.2.1.1
rsIpRipFilterLclTypemandatory Type of filter - input/output	Enumeration Enumerated Values: 1 input 2 output	.1.3.6.1.4.1.89.26.8.2.1.2
rsIpRipFilterLclNumbermandatory Number of RIP filter for this Interface	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.2.1.3
rsIpRipFilterLclStatusmandatory The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.	Enumerationr/w Enumerated Values: 1 valid 2 invalid 3 underCreation	.1.3.6.1.4.1.89.26.8.2.1.4
rsIpRipFilterLclIpAddrmandatory network prefix IP address, as in the forwarding table.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.89.26.8.2.1.5
rsIpRipFilterLclNetworkMaskBitsmandatory the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.2.1.6
rsIpRipFilterLclMatchBitsmandatory the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this va…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.8.2.1.7
rsIpRipFilterLclActionmandatory Filter action - permit/deny	Enumerationr/w Enumerated Values: 1 deny 2 permit	.1.3.6.1.4.1.89.26.8.2.1.8

This table is parralel to IPv6 MIB (RFC4293) ipIfTable, and is 
used to
          
add/delete entries to/from that table. In addition it contains
private objects.

ipIfEntry row .1.3.6.1.4.1.89.26.11.1

The addressing information for one of this
entity's IP addresses.

Indexes

ipIfAddr

Column	Syntax	OID
ipIfAddrmandatory The IP address to which this entry's addressing information pertains.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.89.26.11.1.1
ipIfPrefixmandatory The IP address's prefix.	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.89.26.11.1.2
ipIfIndexmandatory The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.11.1.3
ipIfFwdBroadcastmandatory This variable controls forwarding of IP (sub)net-directed broadcasts destined for an attached sub(net).	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.26.11.1.4
ipIfBcastAddrmandatory Indicates how the host part of ip subnet broadcast messages will be filled: 0 - host part will be filled by 0 1 - host part will be filled by 1.	Integer32r/w Constraints: range: 0-1	.1.3.6.1.4.1.89.26.11.1.5
ipIfVlanTagmandatory The vlan Tag value that represent this ip interface this filed include both vlna tag and vlan priority	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.11.1.6
ipIfLabelmandatory User textual dscription of the ip interface.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.89.26.11.1.7
ipIfEntryStatusmandatory It is used to delete an entry	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.26.11.1.8
ipIfBackupAddrmandatory The ip address of the peer address. It is used by CDE and High Availability.	IPV6-TCIpv6Addressr/w Type Constraints: range: 16	.1.3.6.1.4.1.89.26.11.1.9

This entity's IP Routing table.

ipSpecRouteEntry row .1.3.6.1.4.1.89.26.12.1

A particular route to a particular destination, under a
particular policy (as reflected in the ipSpecRoutePolicy object).

Dynamically created rows will survive an agent reboot.

Implementers nee…

Indexes

ipSpecRouteDest ipSpecRoutePfxLen ipSpecRouteNextHop

Column	Syntax	OID
ipSpecRouteDestmandatory The destination IP address of this route. The values for the index objects ipSpecRouteDest and ipSpecRoutePfxLen must be consistent. When the value of ipSpecRouteDest (excluding the zone index, if one is…	IPV6-TCIpv6Addressr/w Type Constraints: range: 16	.1.3.6.1.4.1.89.26.12.1.1
ipSpecRoutePfxLenmandatory The prefix length. For IPv4 must be <=32, for IPv6 <= 128. The values for the index objects ipSpecRouteDest and ipSpecRoutePfxLen must be consistent. For IPv4 must be <=32, for IPv6 <= 128. If not, then …	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.89.26.12.1.2
ipSpecRouteNextHopmandatory On remote routes, the address of the next system en route. For non-remote routes, a zero length string. The type of this address is determined by the value of the ipSpecRouteNextHopType object.	IPV6-TCIpv6Addressr/w Type Constraints: range: 16	.1.3.6.1.4.1.89.26.12.1.3
ipSpecRouteMetricmandatory The primary routing metric for this route. The semantics of this metric are determined by the routing- protocol specified in the route's ipSpecRouteProto value. The default value is 1.	Integer32r/w Constraints: range: 1-9999	.1.3.6.1.4.1.89.26.12.1.4
ipSpecRoutePortmandatory The Port value that identifies the local port/interface through which the next hop of this route should be reached.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.12.1.5
ipSpecRouteLabelmandatory User defined data.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.89.26.12.1.6
ipSpecRouteStatusmandatory The row status variable, used according to row installation and removal conventions. A row entry cannot be modified when the status is marked as active(1).	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.26.12.1.7

This entity's ND table.

ip6NetToMediaEntry row .1.3.6.1.4.1.89.26.13.1

The addressing information for one of this
entity's ND addresses.

Indexes

ip6NetToMediaIfIndex ip6NetToMediaNetAddress

Column	Syntax	OID
ip6NetToMediaIfIndexmandatory The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.26.13.1.1
ip6NetToMediaPhysAddressmandatory The media-dependent `physical' address.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.89.26.13.1.2
ip6NetToMediaNetAddressmandatory The IpAddress corresponding to the media- dependent `physical' address.	IPV6-TCIpv6Addressr/w Type Constraints: range: 16	.1.3.6.1.4.1.89.26.13.1.3
ip6NetToMediaTypemandatory The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface ident…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 dynamic 4 static	.1.3.6.1.4.1.89.26.13.1.4

An entry of this table specifies an new ifIndex with a type of
propVirtual(53).

virtualLanEntry row .1.3.6.1.4.1.89.27.1.1

A list of information for each virtual LAN.

Indexes

vlIfIndex

Column	Syntax	OID
vlIfIndexmandatory An logical interface number, corresponded this VL	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.27.1.1.1
vlProtomandatory The protocol, supported by this VL. The meanings of the values are: other: none of the following. This VL includes any protocol except the following protocols. It is a bridging VL. RS relies on a third-pa…	Enumerationr/w Enumerated Values: 1 other 2 ip 3 ipmulticast 4 ipxRaw 5 ipxET 6 ipxLLC 7 ipxSNAP 8 decNET 9 decLAT 10 netBios 11 appleTalk 12 xns 13 sna 14 userDefined	.1.3.6.1.4.1.89.27.1.1.2
vlAutoConfigEnablemandatory It is used only in the case of IP. The meanings of the values are: true(1): Autolearning is used for this VL false(2): Autolearning isn't used for this VL from ports, specified in the table virtualLanAutoConf…	TruthValuer/w Type Values: 1 true 2 false	.1.3.6.1.4.1.89.27.1.1.3
vlStatusmandatory It is used to delete an entry	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.27.1.1.4
vlTypemandatory regular - ordinary type specBroadcast - for switches that support VLANs as a set of ports and only as a broadcast domain: broadcast frames do not cross VLAN's bounders, but unicast …	Enumerationr/w Enumerated Values: 1 regular 2 specBroadcast 3 specArpReq 4 specBroadcastAndUnicast 5 specArpReqAndUnicast	.1.3.6.1.4.1.89.27.1.1.5

For each VL (a ifIndex with a type of propVirtual(53)) an entry of  this
table specifies a set of ports, which it contains.

virtualLanPortEntry row .1.3.6.1.4.1.89.27.2.1

A entry of this table specifies a VL and a port belonging to it

Indexes

vLIfIndex vLPortIfIndex

Column	Syntax	OID
vLIfIndexmandatory An logical interface number, corresponding to this VL	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.27.2.1.1
vLPortIfIndexmandatory A physical port belonging to the VL specified by vlIfIndex.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.27.2.1.2
vLPortTypemandatory static means configured by user dynamic means autoconfigured by the RS	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.89.27.2.1.3
vLPortStatusmandatory It is used to delete an entry	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.27.2.1.4

This table specifies per a routing protocol a set of ports, from which
RS will automatically  learning VL in accordance with rules, defined
by the protocol.

virtualLanAutoConfEntry row .1.3.6.1.4.1.89.27.3.1

One port, specified by vlAutoConfPortIfIndex, for which the RS will
automatically learn its VL in accordance with rules, defined
by the protocol specified in vlAutoConfProto.

Indexes

vlAutoConfPortIfIndex vlAutoConfProto

Column	Syntax	OID
vlAutoConfPortIfIndexmandatory Port on which the autoconfig option should be supported	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.27.3.1.1
vlAutoConfProtomandatory Protocol for which the autoconfig option is supported for the port specified by vlAutoConfPortIfIndex	Enumeration Enumerated Values: 2 ip	.1.3.6.1.4.1.89.27.3.1.2
vlAutoConfStatusmandatory It is used to delete an entry	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.27.3.1.3

This table enable the user to add interface  to the RS.
RS will automatically  add the new interface to the interface Table

rsIfConfEntry row .1.3.6.1.4.1.89.28.1.1

Each entry defines a configured interface.

Indexes

rsIfConfIndex

Column	Syntax	OID
rsIfConfIndexmandatory This variable uniquely identifies the interface. It is used as a cross reference in other system tables	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.28.1.1.1
rsIfConfTypemandatory This variable identifies the type of the specific entry in the rsIfConfTable. This field is writable only at creation time (i.e., when value of status is underCreation).	RsIfTyper/w Type Values: 23 ppp 32 frameRelay 500 virtualNet 1000 rndWan 1001 cod 1002 backup 1003 fr1490 1010 b1isdn 1011 b2isdn 1100 unknown	.1.3.6.1.4.1.89.28.1.1.2
rsIfConfNamemandatory This variable provides a logical name to a specific entry in rsIfConfTable	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.89.28.1.1.3
rsIfConfStatusmandatory The status of the ConfigEntry. The choices are those defined in SNMPv2-TC. Only: active, createAndWait, and destroy will be used. active - The conceptual row is available for use by the managed device. createAndWait - …	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.28.1.1.4

The Event Message table of the agent

eventMessageEntry row .1.3.6.1.4.1.89.29.6.1

The row definition for this table.

Indexes

eventNum

Column	Syntax	OID
eventNummandatory The event number,the index of this table.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.6.1.1
eventDescmandatory The event discription, this text will include time and severity.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.89.29.6.1.2

The Bridge Fast Forwarding Table

reaBridgeFftEntry row .1.3.6.1.4.1.89.29.7.12.1

The row definition for this table.

Indexes

reaBrgFftEntryNum

Column	Syntax	OID
reaBrgFftEntryNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.12.1.1
reaBrgFftMacAddrmandatory	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.89.29.7.12.1.2
reaBrgFftReNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.12.1.3
reaBrgFftPortNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.12.1.4
reaBrgFftFacsSrcIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.12.1.5
reaBrgFftFacsDstIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.12.1.6

The IP Fast Forwarding Table

reaIpFftEntry row .1.3.6.1.4.1.89.29.7.15.1

The row definition for this table.

Indexes

reaIpFftEntryNum

Column	Syntax	OID
reaIpFftEntryNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.15.1.1
reaIpFftDstIpAddrmandatory	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.29.7.15.1.2
reaIpFftDstIpMaskmandatory	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.29.7.15.1.3
reaIpFftRangeTypemandatory	Enumeration Enumerated Values: 1 direct 2 remote	.1.3.6.1.4.1.89.29.7.15.1.4
reaIpFftSrcMacAddrmandatory	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.89.29.7.15.1.5
reaIpFftDstMacAddrmandatory	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.89.29.7.15.1.6
reaIpFftReNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.15.1.7
reaIpFftPortNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.15.1.8
reaIpFftFacsSrcIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.15.1.9
reaIpFftFacsDstIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.15.1.10
reaIpFftApplFlagsmandatory A bit mask that defines the applications associated with this entry: __________________________________________ | Byte 1|Byte 2 |Byte 3 | ....|Byte 20 | |87654321| | 87654321| |________|___________…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.89.29.7.15.1.11

The IPX Fast Forwarding Table

reaIpxFftEntry row .1.3.6.1.4.1.89.29.7.16.1

The row definition for this table.

Indexes

reaIpxFftEntryNum

Column	Syntax	OID
reaIpxFftEntryNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.1
reaIpxFftDstNetidmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.2
reaIpxFftRangeTypemandatory	Enumeration Enumerated Values: 1 direct 2 remote	.1.3.6.1.4.1.89.29.7.16.1.3
reaIpxFftSrcMacAddrmandatory	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.89.29.7.16.1.4
reaIpxFftDstMacAddrmandatory	RFC1213-MIBPhysAddress	.1.3.6.1.4.1.89.29.7.16.1.5
reaIpxFftReNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.6
reaIpxFftPortNummandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.7
reaIpxFftFacsSrcIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.8
reaIpxFftFacsDstIndexmandatory	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.16.1.9

The Bridge Responsibility Table

lreVnResposibilityEntry row .1.3.6.1.4.1.89.29.7.17.1

The row definition for this table.

Indexes

lreVnRespVn

Column	Syntax	OID
lreVnRespVnmandatory	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.29.7.17.1.1
lreVnRespStatusmandatory	RowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.29.7.17.1.2

A table holding STP instances running on device

rsStpInstanceEntry row .1.3.6.1.4.1.89.30.7.1

An entry in the STP instances table

Indexes

rsStpInstanceVlanId

Column	Syntax	OID
rsStpInstanceVlanIdmandatory Vlan of STP instance.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.30.7.1.1
rsStpInstanceBridgePrioritymandatory Current bridge priority.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.89.30.7.1.2
rsStpInstanceHelloTimemandatory Hello Time (in seconds).	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.89.30.7.1.3
rsStpInstanceMaxAgingTimemandatory Max Aging Time (in seconds).	Integer32r/w Constraints: range: 6-40	.1.3.6.1.4.1.89.30.7.1.4
rsStpInstanceForwardDelayTimemandatory Forward Delay Time (in seconds).	Integer32r/w Constraints: range: 4-30	.1.3.6.1.4.1.89.30.7.1.5
rsStpInstanceEnabledmandatory Whether this STP instance is enabled	FeatureStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.89.30.7.1.6
rsStpInstanceRootIdmandatory Spanning Tree Root Id.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.89.30.7.1.7
rsStpInstanceRootPathCostmandatory Spanning Tree Root Path Cost.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.30.7.1.8
rsStpInstanceDesignatedBridgeIdmandatory Designated Bridge Id.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.89.30.7.1.9
rsStpInstanceDesignatedPortIdmandatory Designated Port Id.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.30.7.1.10

A table holding STP Information and instance mapping for each port

rsStpPortEntry row .1.3.6.1.4.1.89.30.8.1

An entry in the STP ports table

Indexes

rsStpPortId

Column	Syntax	OID
rsStpPortIdmandatory Port Id.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.30.8.1.1
rsStpPortVlanIdmandatory Vlan this port belongs to.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.30.8.1.2
rsStpPortPrioritymandatory STP Priority for this port.	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.89.30.8.1.3
rsStpPortPathCostmandatory Port Path Cost.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.89.30.8.1.4
rsStpPortModeFastmandatory Whether this port is an Edge port, and should start forwarding immediately.	FeatureStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.89.30.8.1.5
rsStpPortEnabledmandatory Whether this port participates in spanning tree	FeatureStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.89.30.8.1.6
rsStpPortStatemandatory Port State according to STP Algorithm.	Enumeration Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.89.30.8.1.7
rsStpPortRolemandatory Port Role according to STP Algorithm.	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup	.1.3.6.1.4.1.89.30.8.1.8

In this table the WSD collects statistics per servers.

rsWSDServerStatEntry row .1.3.6.1.4.1.89.35.1.12.1

The row definition for this table.

Indexes

rsWSDSerStatName

Column	Syntax	OID
rsWSDSerStatNamemandatory This variable indicate the name assigned by the user to the serve.	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.89.35.1.12.1.1
rsWSDSerStatAttUsersNummandatory The total number of currently active users attached to this server.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.2
rsWSDSerStatPeakLoadmandatory Maximal number of frames per second dispatched to server since last reset.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.3
rsWSDSerStatFramesRatemandatory Number of frames per second dispatched to server.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.4
rsWSDSerStatFramesLoadmandatory Number of frames per second dispatched to server.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.89.35.1.12.1.5
rsWSDSerStatRecoveryTimemandatory Number of seconds after server initialization during which ISD won't send any requests.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.6
rsWSDSerStatWarmUpTimemandatory Number of seconds after server recovery during which the server will get less requests than permitted by his weight and load.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.7
rsWSDSerStatConnectionLimitmandatory The maximal number of client sessions which can be opened on this sever.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.8
rsWSDSerStatAdminStatusmandatory Administrative status of physical server. enable - activates the server. The rsADServerOperStatus will change to active. connectionsShutdown - gracefully shuts down connections to the server by allowing exi…	Enumerationr/w Enumerated Values: 1 enable 2 connectionsShutdown 3 sessionsShutdown	.1.3.6.1.4.1.89.35.1.12.1.9
rsWSDSerStatConnectionLimitReachedmandatory Connection limit reached flag.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.12.1.10

List of Farm IP addresses backed up by this router.

wsdRedundEntry row .1.3.6.1.4.1.89.35.1.16.1

The row definition for this table.

Indexes

wsdRedundFarmAddr wsdRedundMainWsdAddr

Column	Syntax	OID
wsdRedundFarmAddrmandatory The Farm Virtual Ip address on which the redundancy feature operates.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.35.1.16.1.1
wsdRedundMainWsdAddrmandatory The Ip address of the polled main wsd.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.89.35.1.16.1.2
wsdRedundOperStatusmandatory If active, the main wsd is considered inactive and the IP interface operates as its backup.	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.89.35.1.16.1.3
wsdRedundPollIntervalmandatory Polling interval for the main wsd (in seconds). If 0 the wsd is not polled.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.16.1.4
wsdRedundTimeoutmandatory Interval in seconds during which the backed-up wsd must signal. If it does not signal, it is considered inactive and the IP interface starts operating as backup.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.16.1.5
wsdRedundStatusmandatory Entry status	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.89.35.1.16.1.6

In this table the WSD collects NT statistics per servers.

rsWSDNTCheckEntry row .1.3.6.1.4.1.89.35.1.28.1

The row definition for this table.

Indexes

rsWSDNTSerialNum

Column	Syntax	OID
rsWSDNTSerialNummandatory The serial number of the algorithm.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.1
rsWSDNTFrequentCheckPeriodmandatory The period for getting the frequent NT variables.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.2
rsWSDNTOpenSessionsWeightmandatory The weight for currently open sessions consideration.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.3
rsWSDNTIncomingTrafficWeightmandatory The weight for incoming traffic consideration.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.4
rsWSDNTOutgoingTrafficWeightmandatory The weight for outgoing traffic consideration.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.5
rsWSDNTRegularCheckPeriodmandatory The period for getting the regular NT variables.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.6
rsWSDNTAvResponseWeightmandatory The weight for average response time.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.7
rsWSDNTUsersLimitWeightmandatory The weight for the users limit on the server.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.8
rsWSDNTTCPLimitWeightmandatory The weight for the TCP connections limit on the server.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.9
rsWSDNTRetriesmandatory The number of retries before issuing a trap.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.28.1.10
rsWSDNTCommunitymandatory The SNMP community name with which we access the servers.	OctetStringr/w Constraints: range: 1-30	.1.3.6.1.4.1.89.35.1.28.1.11

In this table the WSD collects private statistics per server.

rsWSDPrivateCheckEntry row .1.3.6.1.4.1.89.35.1.29.1

The row definition for this table.

Indexes

rsWSDPrivateSerialNum

Column	Syntax	OID
rsWSDPrivateSerialNummandatory The serial number of the algorithm.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.29.1.1
rsWSDPrivateSpecialCheckPeriodmandatory The period for getting the private variables.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.29.1.2
rsWSDPrivateExtraVar1IDmandatory This MIB variable will be retrieved from the server.	ObjectIdentifierr/w	.1.3.6.1.4.1.89.35.1.29.1.3
rsWSDPrivateExtraVar1Weightmandatory The weight for variable number 1.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.29.1.4
rsWSDPrivateExtraVar2IDmandatory This MIB variable will be retrieved from the server.	ObjectIdentifierr/w	.1.3.6.1.4.1.89.35.1.29.1.5
rsWSDPrivateExtraVar2Weightmandatory The weight for variable number 2.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.29.1.6
rsWSDPrivateRetriesmandatory The number of retries before issuing a trap.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.29.1.7
rsWSDPrivateCommunitymandatory The SNMP community name with which we access the servers.	OctetStringr/w Constraints: range: 1-30	.1.3.6.1.4.1.89.35.1.29.1.8
rsWSDPrivateExtraVar1Modemandatory Specify the type of parameter. Ascending means that the value of 100 is the best (Idle CPU percentage). Descending means that the value of 0 is the best (CPU utilization percentage)	Enumerationr/w Enumerated Values: 1 ascending 2 descending	.1.3.6.1.4.1.89.35.1.29.1.9
rsWSDPrivateExtraVar2Modemandatory Specify the type of parameter. Ascending means that the value of 100 is the best (Idle CPU percentage). Descending means that the value of 0 is the best (CPU utilization percentage)	Enumerationr/w Enumerated Values: 1 ascending 2 descending	.1.3.6.1.4.1.89.35.1.29.1.10

RND-specific interface table.  Each table entry includes an
index, Board number, Network Address, interface status, clock
indicator and interface cost.

rsWSDIfEntry row .1.3.6.1.4.1.89.35.1.41.1

The row definition for this table.

Indexes

rsWSDIfIndex

Column	Syntax	OID
rsWSDIfIndexmandatory Index to the RND Interface Table. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIBII).	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.41.1.1
rsWSDIfBoardNummandatory The interface defined by this entry correspTnds to the board defined by the same value of rndSlotBoardNum in the rndSlotTab.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.41.1.2
rsWSDIfNetAddressmandatory The IP address of the interface defined by the particular value of rsWSDIfIndex.	RFC1155-SMINetworkAddress	.1.3.6.1.4.1.89.35.1.41.1.3
rsWSDIfStatusmandatory The current status of the interface.	Enumeration Enumerated Values: 1 ok 2 okSingleBrg 3 okMultiBrg 4 connctFault 5 rxFault 6 txFault 7 channelLoopback 8 rxClockFault 9 t1Alarm	.1.3.6.1.4.1.89.35.1.41.1.4
rsWSDIfClockTypemandatory rsWSDIfClockType defines the type of clock each interface uses: internal or external.	Enumerationr/w Enumerated Values: 1 external 2 internal 3 t1 4 g703	.1.3.6.1.4.1.89.35.1.41.1.5
rsWSDIfBaudRatemandatory Defines the baud rate of use by the interface. The valid rates are determined by the type of the media for which this baud rate is defined.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.41.1.6
rsWSDIfCostmandatory This variable assigns a transmission cost to the interface (channel or LAN). These costs are used in Level II routing. The costs aretypically inversly proportional to the channel quality.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.41.1.7
rsWSDIfCompressionmandatory Defines whether data compression is enabled or disabled for the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.35.1.41.1.8
rsWSDIfCompressionStatusmandatory Defines the status of the compression component: not-inserted - Compression component is not in the device active - Compression is enabled and operates correctly not-active - Compression is enables but does not oper…	Enumeration Enumerated Values: 1 not-inserted 2 active 3 not-active 4 disable	.1.3.6.1.4.1.89.35.1.41.1.9
rsWSDIfCompressionRatemandatory Percentage of compression. This variable applies only if rndCompressionStatus is active.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.89.35.1.41.1.10
rsWSDIfLATCompressionmandatory Enable/Disable the LAT Compression.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.35.1.41.1.11
rsWSDIfCompressionTypemandatory This parameter indicates the type of compression option available in the device. none(1) - indicates that there is no compression option in the device lowSpeed(2) - indicates a compression option which is operation…	Enumeration Enumerated Values: 1 none 2 lowSpeed 3 highSpeed	.1.3.6.1.4.1.89.35.1.41.1.12
rsWSDIfFilterModemandatory This parameter indicates the type of filtering in the device.	Enumerationr/w Enumerated Values: 1 destinationOnly 2 sourceAndDestination 3 none	.1.3.6.1.4.1.89.35.1.41.1.13
rsWSDIfChannelTypemandatory The type of the WAN channel	Enumerationr/w Enumerated Values: 1 wanChannel 2 ogRanPort 3 routerToBridge 4 spsFramRelay 5 dialBackup 6 snar 7 lan 8 spsX25 9 frameRelay1490 10 frameRelay1490CAR 11 frameRelayCAR 12 ppp	.1.3.6.1.4.1.89.35.1.41.1.14
rsWSDIfBridgemandatory This variable indicates whether this interface forward Layer II pakages.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.35.1.41.1.15
rsWSDHighPriorityIfmandatory This variable indicates whether this interface will forward pakages that fit HighPriority set by the manager.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.89.35.1.41.1.16
rsWSDWanHeadermandatory This variable indicates the RND WAN header type used for frames which pass through this interface. 'regular' specifies a 14 bytes header compatible with older OG versions and 'short' a 4 byte header compatible with the …	Enumerationr/w Enumerated Values: 1 regular 2 short	.1.3.6.1.4.1.89.35.1.41.1.17
rsWSDDuplexModemandatory This variable indicates whether this interface operates in half duplex full duplex or auto negotiation mode.	Enumerationr/w Enumerated Values: 1 half 2 full 3 auto	.1.3.6.1.4.1.89.35.1.41.1.18