RAD-ds1Interface-MIB Table View

A list of current statistics entries.  This table
contains additional objects for the current table.

dsx1XCurrentEntry row .1.3.6.1.4.1.164.3.1.6.4.1.2.1

An entry containing additional statistical counters
applicable to a particular current table.

Indexes

DS1-MIBdsx1CurrentIndex

Column	Syntax	OID
dsx1CurrentLOS The counter associated with the number of LOS seconds, encountered by a DS1 interface in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.1
dsx1CurrentLOF The counter associated with the number of LOF seconds, encountered by a DS1 interface in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.2
dsx1CurrentLOC Loss Of Cell delineation. Counts number of cells the ATM UNI cells receiver lost cells delineation .	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.3
dsx1CurrentAIS The counter associated with the number of AIS seconds, encountered by a DS1 interface in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.4
dsx1CurrentRAI Remote Alarm Indication: Transmitted in the outgoing direction (toward the PABX) over FDL bits when the DS1 device detected an incoming Loss Of Frame. Received from the far end (PABX) over FDL when it detects a Loss of…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.5
dsx1CurrentLOMF Loss of Multi-Frame sequence in E1 time slot 16.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.6
dsx1CurrentFEBE Far End Block Errors, as reported in the first bit of frames 13 and 15, on multiframe E1 lines with CRC4, in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.7
dsx1CurrentStatus The statuses of the current interval: 0 - Valid. 1 - redundantLinkSwitch - the link has been switched by a redundancy mechanism. 2 - discontinuity - module was partialy out. 4 - notValid - module is out.	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.8
dsx1CurrentBPV The counter associated with the number of BPVs (Bi-Polar Violations) encountered by a DS1 interface in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.9
dsx1CurrentLOCRCMF Loss of CRC4 Multi-Frame sequence in E1. encountered in the current 15 minute interval	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.10
dsx1CurrentLOFC Counts the number of loss of frame events measured. encountered in the current 15 minute interval	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.11
dsx1CurrentCRCErrors Counts the number of CRC error events, encountered in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.12
dsx1CurrentLSES Counts the number of LSES (Line Severely Errored Seconds) encountered in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.13
dsx1CurrentFC Counts the number of FC (Path failure events) encountered in the current 15 minute interval.	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.3.1.6.4.1.2.1.14

A list of Total statistics entries.  This table
contains additional objects for the Total table.

dsx1XTotalEntry row .1.3.6.1.4.1.164.3.1.6.4.1.4.1

An entry containing additional statistical counters
applicable to a particular total table.

Indexes

DS1-MIBdsx1TotalIndex

Column	Syntax	OID
dsx1TotalLOS The counter associated with the number of LOS (Loss of Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.1
dsx1TotalLOF The counter associated with the number of LOF (Loss of Frame) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.2
dsx1TotalAIS The counter associated with the number of AIS (Alarm Indication Signal) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.4
dsx1TotalRAI The counter associated with the number of RAIS (Remote Alarm Indication) seconds encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.5
dsx1TotalBPV The counter associated with the number of BPV (Bi-Polar Violations) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.9
dsx1TotalLOFC The counter associated with the number loss of frames encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.11
dsx1TotalLSES Counts the number of LSES (Line Severely Errored Seconds) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.13
dsx1TotalFC Counts the number of FC (Path failure events) encountered by a DS1 interface in the previous 24 hour interval. Invalid 15 minute intervals count as 0.	PerfHist-TC-MIBPerfTotalCount	.1.3.6.1.4.1.164.3.1.6.4.1.4.1.14

The DS1 Data Stream Statistics table.

dsx1DataStreamStatEntry row .1.3.6.1.4.1.164.3.1.6.4.1.5.1

An entry in the DS1 Data Stream Statistics table.

Indexes

dsx1DataStreamStatIfIndex dsx1DataStreamStatIndex

Column	Syntax	OID
dsx1DataStreamStatIfIndex The index of the DS1 interface. It may be ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.1
dsx1DataStreamStatIndex The DS1 Data Stream Index. For Vmux - the following indices are used: 1 for Transparent 2-3 for SS71-SS72 (respectively) 4-7 for Data1-Data4 (respectively) 8 for HDLC Ph2 Compatible 9-16 for Sub-CH1-1...…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.2
dsx1DataStreamStatValid Indicates whether this Data Stream is valid or not. When invalid - all counters are irrelevant.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.3
dsx1DataStreamStatInFrames The counter associated with the number of received frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.4
dsx1DataStreamStatInBytes The counter associated with the number of received bytes, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.5
dsx1DataStreamStatInDiscards The counter associated with the number of Discarded incoming frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.6
dsx1DataStreamStatInErrors The counter associated with the number of received Errored frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.7
dsx1DataStreamStatOutFrames The counter associated with the number of transmitted frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.8
dsx1DataStreamStatOutBytes The counter associated with the number of transmitted bytes, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.9
dsx1DataStreamStatOutDiscards The counter associated with the number of Discarded outgoing frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.10
dsx1DataStreamStatOutErrors The counter associated with the number of errored transmitted frames, encountered by the DS1 Data Stream.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.1.5.1.11

An extension to the DS1 Configuration table.

dsx1XConfigEntry row .1.3.6.1.4.1.164.3.1.6.4.2.1

An entry containing additional configuration
parameters.

Indexes

DS1-MIBdsx1LineIndex

Column	Syntax	OID
dsx1IdleCode Byte pattern of the data received/transmitted in the E1T1 framer idle timeslots. Valid range: (0 - FF HEX).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.1
dsx1LineMode T1 device operation mode. Valid for T1 only.	Enumerationr/w Enumerated Values: 1 csu 2 dsu	.1.3.6.1.4.1.164.3.1.6.4.2.1.2
dsx1dBTxGain Transmit line Gain for T1 CSU line mode.	Enumerationr/w Enumerated Values: 1 notApplicable 2 neg75dB 3 neg15dB 4 neg225dB 5 zerodB	.1.3.6.1.4.1.164.3.1.6.4.2.1.3
dsx1RxSensitivity Low Sensitivity is considered Short Haul while High Sensitivity is considered Long Haul. The actual values depend on the LIU. Examples: - E1: -12dB is considered Short Haul ; -43dB is considered Long Haul - T1: -12dB is…	Enumerationr/w Enumerated Values: 1 notApplicable 2 longHaul 3 shortHaul 4 monitor	.1.3.6.1.4.1.164.3.1.6.4.2.1.4
dsx1RestoreTime Used to change the sync. algorithms to reduce the time required for the port to return to normal operation after a RED alarm. 'sec1' = Fast, 'sec10' = TR-6211, 'immediate' = CCITT	Enumerationr/w Enumerated Values: 1 other 2 sec1 3 sec10 4 immediate	.1.3.6.1.4.1.164.3.1.6.4.2.1.5
dsx1TcFirstSignal Trunk conditioning signal - value to be sent as a signal during the first 2.5 seconds after alarm detection. Range is 0x0..0xF. 0xFF is a NULL value. This variable is used also for Space Signaling Code (in this cas…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.6
dsx1TcSignal Trunk conditioning signal value after alarm detection. Range is 0x1..0xF for E1, and 0x0..0xF for T1. This variable is used also for Space Signaling Code (E1 and T1).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.7
dsx1TcPattern Trunk conditioning data pattern to be sent upon a DS0 fail. Range is 0x0..0xFF. This variable used also for Out of Service Code.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.8
dsx1Scramble Scrambling is an operation that randomizes the bits of the payload of the ATM cell by a polynom. This operation helps with the error detection mechanism of the HEC. Not applicable for E1. active - will scramble/descram…	Enumerationr/w Enumerated Values: 1 notApplicable 2 notActive 3 active	.1.3.6.1.4.1.164.3.1.6.4.2.1.9
dsx1LineAdaptiveTimingMode Enables end to end clock synchronization. Default value - off.	Enumerationr/w Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.164.3.1.6.4.2.1.10
dsx1TxClockSource The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'localTiming' indicates that a local clock source is used or when an external clock i…	Enumerationr/w Enumerated Values: 1 loopTiming 2 localTiming 3 throughTiming 4 adaptive 5 system	.1.3.6.1.4.1.164.3.1.6.4.2.1.11
dsx1AisEnable Enable/ disable AIS transmit when Ethernet cable (for TDMoIP) is out (disconnected).	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.3.1.6.4.2.1.12
dsx1TsEchoCancel This parameter defines for each TS whether Echo-Cancellation is on. Each bit represents one TS as follow: First octet bit'0' = TS#1, bit'7' = TS#8, .. 2nd octet bit'0' = TS#9,.., 4th octet bit'7' = TS#32. Octets and bi…	OctetStringr/w Constraints: range: 4-4	.1.3.6.1.4.1.164.3.1.6.4.2.1.13
dsx1EchoCancelerModule This parameter indicates whether echo-cancellation module exists for this line.	Enumeration Enumerated Values: 2 notExist 3 exist	.1.3.6.1.4.1.164.3.1.6.4.2.1.14
dsx1PortFunction This object determines the ATM Mode over the physical port. uni - The port will function as an ATM UNI. ces - The port will function as a CES. ima - The port will function as an IMA-ATM. cesPsn - The port will…	Enumerationr/w Enumerated Values: 1 notApplicable 2 uni 3 ces 4 ima 5 cesPsn 6 abis	.1.3.6.1.4.1.164.3.1.6.4.2.1.15
dsx1PortMultiplier This object determines the data rate of each TS (Kbps units). This parameter is applicable for T1 only.	Enumerationr/w Enumerated Values: 1 notApplicable 2 r56 3 r64	.1.3.6.1.4.1.164.3.1.6.4.2.1.16
dsx1LeasedLine This parameter defines whether Line mode is regular (non Leased Line mode) or transparent (Leased Line mode).	Enumerationr/w Enumerated Values: 1 notApplicable 2 disable 3 enable	.1.3.6.1.4.1.164.3.1.6.4.2.1.17
dsx1CsuLoop This parameter defines where the CSU loop will be done: local - locally (by IPmux) towards the TDM device transparent - transferred to Remote Device that will send it to its connected TDM device. remote - …	Enumerationr/w Enumerated Values: 1 notApplicable 2 local 3 transparent 4 remote	.1.3.6.1.4.1.164.3.1.6.4.2.1.18
dsx1ClockSource This entry specifies the source from which the clock will be taken. Refer to device specification for source Index	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.19
dsx1OosSignal This parameter defines the value to be sent as a signal after alarm detection: 'Space' = both A and B signaling bits are forced to '0' during out-of-service periods. 'Mark' = both A and B signaling bits a…	Enumerationr/w Enumerated Values: 1 notApplicable 2 space 3 mark 4 spaceMark 5 markSpace	.1.3.6.1.4.1.164.3.1.6.4.2.1.20
dsx1BundleNextIndex This parameter indicates the Next free Bundle Index for this DS1 port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.3.1.6.4.2.1.21
dsx1CRC6CalcMode This object determines the CRC6 Calculation mode. jtG704 =JT-G704 = the Japanese standard ituG704=ITU-G704 = the International standard This parameter is applicable for J1 only.	Enumerationr/w Enumerated Values: 1 jtG704 2 ituG704	.1.3.6.1.4.1.164.3.1.6.4.2.1.22
dsx1SendUponFail This object determines which notification will be sent to the other side upon fail of another interface. In Ipmux14 the notification is sent upon failure of the Ethernet link.	Enumerationr/w Enumerated Values: 2 oosCode 3 ais	.1.3.6.1.4.1.164.3.1.6.4.2.1.23
dsx1InbandLoopSignal This parameter defines the signal pattern for inband loopback activation and deactivation: csu Applicable only for SF (D4) and ESF line types Defined in AT&T TR54016 and ANSI T1.403. Loop-up pattern - 000…	Enumerationr/w Enumerated Values: 1 notApplicable 2 csu 3 fdlLine 4 fdlNetwork 5 niuFac1 6 niuFac2 99 program	.1.3.6.1.4.1.164.3.1.6.4.2.1.24
dsx1InbandLoopUpCode This parameter specifies the inband signal pattern that shall cause activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuLoop is local(2) or remote(4), and the value…	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.4.2.1.25
dsx1InbandLoopUpLength This parameter specifies the length, in bits, of the inband signal pattern that shall cause activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuLoop is local(2) or …	bitsUnsigned32r/w Constraints: range: 3-8	.1.3.6.1.4.1.164.3.1.6.4.2.1.26
dsx1InbandLoopDownCode This parameter specifies the inband signal pattern that shall cause de-activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuLoop is local(2) or remote(4), and the va…	OctetStringr/w	.1.3.6.1.4.1.164.3.1.6.4.2.1.27
dsx1InbandLoopDownLength This parameter specifies the length, in bits, of the inband signal pattern that shall cause de-activation of a loopback. The specified pattern is applicable only when the value of dsx1CsuLoop is local(2) …	bitsUnsigned32r/w Constraints: range: 3-8	.1.3.6.1.4.1.164.3.1.6.4.2.1.28
dsx1TxClockInstance When dsx1TransmitClockSource is set to throughTiming(3) or adaptive(4), this parameter specifies the instance of the clock domain or recovered clock, respectively, that shall be used for transmission.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.3.1.6.4.2.1.29
dsx1TxPortQuality This object indicates the port clock quality.	Enumerationr/w Enumerated Values: 1 notApplicable 2 stratum1 3 stratum2 4 stratum3 5 stratum3e 6 stratum4	.1.3.6.1.4.1.164.3.1.6.4.2.1.30

An extension to the DS1 Configuration table that defines
DS1 statistics thresholds.
'Line' means a physical transport of digital information at
    nominal rate of 2.048Mbps or 1.544Mbps.
'Path' means a framed digital signal at nominal rate of
    2.048Mbps or 1.544Mbps independent of the specific
    transmission equipment.

dsx1XStatThresholdEntry row .1.3.6.1.4.1.164.3.1.6.4.3.1

An entry containing statistics thresholds for DS1 port.

Indexes

DS1-MIBdsx1LineIndex

Column	Syntax	OID
dsx1LineIntervalLesThreshold This object configures the threshold for the number of Error Seconds (ES) within any given 15-minute performance Line data collection interval. If the value of Error Seconds in a particular 15-minute collection interval…	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.1
dsx1PathIntervalCvThreshold This object configures the threshold for the number of Code Violations (CV) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minute collection interv…	Unsigned32r/w Constraints: range: 0-16383	.1.3.6.1.4.1.164.3.1.6.4.3.1.2
dsx1PathIntervalEsThreshold This object configures the threshold for the number of Error Seconds (ES) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minute collection interval…	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.3
dsx1PathIntervalSesThreshold This object configures the threshold for the number of Severe Error Seconds (SES) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minute collection …	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.4
dsx1PathIntervalSefsThreshold This object configures the threshold for the number of Severely Errored Framing Seconds (SEFS) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minut…	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.5
dsx1PathIntervalCssThreshold This object configures the threshold for the number of Controlled Slip Seconds (CSS) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minute collecti…	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.6
dsx1PathIntervalUasThreshold This object configures the threshold for the number of Unavailable Seconds (UAS) within any given 15-minute performance Path data collection interval. If the value of Error Seconds in a particular 15-minute collection i…	Unsigned32r/w Constraints: range: 0-900	.1.3.6.1.4.1.164.3.1.6.4.3.1.7