RAD-NtePrtCo-MIB Table View

The Physical interface configuration table.

atmNteConfIfEntry row .1.3.6.1.4.1.164.12.3.2.1.1.1

An entry in the Physical interface configuration table.
The ifIndex is of the lowest physical layer.

Indexes

IF-MIBifIndex

Column	Syntax	OID
atmConfIfTransmitClk The transmit clock of the port.	Enumerationr/w Enumerated Values: 2 internal 3 external 4 loopback 5 adaptive	.1.3.6.1.4.1.164.12.3.2.1.1.1.1
atmConfIfLoopback Interface Loopback.	Enumerationr/w Enumerated Values: 2 internal 3 external 4 disable	.1.3.6.1.4.1.164.12.3.2.1.1.1.2
atmConfIfFrameType The frame type. Valid values for a 155M interface: sonet(2), sdh(3). Valid values for a T3 interface: direct(4), plcpInternal(5), plcpExternal(6), directNoScrmbling(10), plcpInternalNoScrmbling(11), plcpExternalNoScrmbl…	Enumerationr/w Enumerated Values: 1 other 2 sonet 3 sdh 4 direct 5 plcpInternal 6 plcpExternal 7 e3 8 ethCrcTrans 9 ethCrcNotTrans 10 directNoScrmbling 11 plcpInternalNoScrmbling 12 plcpExternalNoScrmbling	.1.3.6.1.4.1.164.12.3.2.1.1.1.3
atmConfIfCardTypedeprecated The card type.	Enumeration Enumerated Values: 1 notApplicable 2 sc13m-155 3 st13s-155 4 st13l-155 5 utp-155 6 cx-bnc-155 7 e3 8 t3 9 e1 10 e1-ltu 11 fc13l-155 12 fc13lh-155 13 fc15lh-155 14 fc13l-e3 15 fc13lh-e3 16 fc15lh-e3 17 fc13l-t3 18 fc13lh-t3 19 fc15lh-t3	.1.3.6.1.4.1.164.12.3.2.1.1.1.4
atmConfAtmIfVpiVciLimit The limit on the sum of the VPI+VCI bits for this interface.	Enumeration Enumerated Values: 2 bits15 3 bits17	.1.3.6.1.4.1.164.12.3.2.1.1.1.5
atmConfIfHwFeatures HW features command.	Enumerationr/w Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.164.12.3.2.1.1.1.6
atmConfIfOutputRate This parameter indicates the output rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.1.1.7
atmConfIfInputRate This parameter indicates the input rate in cells/sec, which is supported per port. Successfully setting this parameter is dependent on all other ports values calculations, which are described in the NMS SRS.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.1.1.8
atmConfAlarmForwarding Enables Path AIS Alarm forwarding upon a failure detection. The following might be considered as a failure: LOS, LOF, LOC, SLM, LOP, Path AIS and Line AIS. disable(2) - will not forward an alarm upon a f…	Enumerationr/w Enumerated Values: 2 disable 3 enable	.1.3.6.1.4.1.164.12.3.2.1.1.1.9
atmConfIfAllocatedBw Total VC Bandwidth Allocation.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.1.1.10
atmConfIfLowerVpi The Lower possible VPI.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.1.1.11
atmConfIfOamMode OAM support Mode, which determines the interface's location in a segment wise.	Enumerationr/w Enumerated Values: 2 segmentTermination 3 endToEndTermination	.1.3.6.1.4.1.164.12.3.2.1.1.1.12
atmConfIfOamFailureInd This object allows user to define the type of indication (if any) that will be created upon a LB cell failure, for all VCs on which OAM loopback traffic is activated. disabled(2) - no indication will be created. …	Enumerationr/w Enumerated Values: 2 disabled 3 ais 4 rdi 5 aisAndRdi	.1.3.6.1.4.1.164.12.3.2.1.1.1.13

The interface Alarm table.

atmNteAlarmIfEntry row .1.3.6.1.4.1.164.12.3.2.1.2.1

An entry in the interface Alarm table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
atmInterfaceActiveAlarms A Bit String of the active alarms on this interface. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - LOS 2 - LOF 3 - Lin…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.1
atmThresholdSectionBIP When Section BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.2
atmThresholdLineBIP When Line BIPs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.3
atmThresholdLineFEBE When Line FEBEs are greater than this threshold, an active alarm is raised. N/A for ds3/e3 interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.4
atmThresholdPathBIP When Path BIPs are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.5
atmThresholdPathFEBE When Path FEBEs are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.6
atmThresholdErroredCells When Errored Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.7
atmThresholdLostCells When Lost Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.8
atmThresholdMisinsertedCells When Misinserted Cells are greater than this threshold, an active alarm is raised.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.9
atmInterfaceAlarmStatus The variable is on(3) when there is any active alarm on this interface.	Enumeration Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.12.3.2.1.2.1.10
atmInterfaceMaskAlarms A Bit String of alarms mask on this interface. An up bit (1) means that the respective alarm is masked. A down bit (0) means no mask. The mask is supported for the following alarms: 1 - LOS	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.2.1.11

The ATM VP configuration table.
The table is an extension to the atmVplTable of
RFC-1695.

atmNteConfVpEntry row .1.3.6.1.4.1.164.12.3.2.1.3.1

An entry in the ATM VP configuration table.
ifIndex of the ATM layer.

Indexes

IF-MIBifIndex ATM-MIBatmVplVpi

Column	Syntax	OID
atmConfVpPolicing Policing method desired for this VPL.	Enumerationr/w Enumerated Values: 1 none 2 police 3 monitor 4 shaping 5 policingAndShaping	.1.3.6.1.4.1.164.12.3.2.1.3.1.1
atmConfVpCCAdminStatus up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activat…	Enumerationr/w Enumerated Values: 2 up 3 down 4 source 5 sink 6 listenToActivationCells 7 originateActivationCells	.1.3.6.1.4.1.164.12.3.2.1.3.1.2
atmConfVpLoopbackAdminStatus up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. …	Enumerationr/w Enumerated Values: 2 up 3 down 4 llid 5 segment 6 endToEnd 7 segmentLlid 8 endToEndLlid	.1.3.6.1.4.1.164.12.3.2.1.3.1.3
atmConfVpLoopbackSinkAddress Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.164.12.3.2.1.3.1.4
atmConfVpCongestionControl Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI	OctetStringr/w	.1.3.6.1.4.1.164.12.3.2.1.3.1.5
atmConfVpCCDirection both(2) - Agent send OAM CC cells and check received OAM CC cells source(4)- Agent send OAM CC cells. sink(5) - Agent checks received OAM CC cells.	Enumerationr/w Enumerated Values: 2 both 4 source 5 sink	.1.3.6.1.4.1.164.12.3.2.1.3.1.6
atmConfVpCreationTime A date-time in which the VP was created.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.164.12.3.2.1.3.1.7
atmConfVpOamSupport OAM support mode, which determines the device location in a segment wise.	Enumerationr/w Enumerated Values: 1 intermediate 2 segmentTermination 3 endToEndTermination	.1.3.6.1.4.1.164.12.3.2.1.3.1.8
atmConfVpCCOperStatus initial(1) - The CC activation process is not started. source(4) - Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC cells. both (8) - OAM CC of local and remote agents activation. timeout (9) - Timeo…	Enumeration Enumerated Values: 1 initial 4 source 5 sink 8 both 9 timeout 10 denied 11 conflict 12 manual	.1.3.6.1.4.1.164.12.3.2.1.3.1.9
atmConfVpLoopbackTraffic This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting …	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.12.3.2.1.3.1.10
atmConfVpLoopbackFailureInd This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of…	Enumerationr/w Enumerated Values: 2 disabled 3 segmentAis 4 segmentRdi 5 segmentAisAndRdi 6 endToEndAis 7 endToEndRdi 8 endToEndAisAndRdi	.1.3.6.1.4.1.164.12.3.2.1.3.1.11
atmConfVpLoopbackFailureThreshold The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.3.1.12
atmConfVpOamDirection The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.	Enumerationr/w Enumerated Values: 1 notApplicable 2 downStream 3 upStream	.1.3.6.1.4.1.164.12.3.2.1.3.1.13
atmConfVpOamDescrIndex This parameter indicates the VPL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.3.1.14
atmConfVpConnected This object indicates whether this VP is connected and if connected, what is it connected to.	Enumerationr/w Enumerated Values: 1 notConnected 2 mng 3 bridgePort 4 ds0Bundle 5 atm 6 pw	.1.3.6.1.4.1.164.12.3.2.1.3.1.15

The ATM VC configuration table.
The table is an extension to the atmVclTable of
RFC-2515.

atmNteConfVcEntry row .1.3.6.1.4.1.164.12.3.2.1.4.1

An entry in the ATM VC configuration table.
ifIndex of the ATM layer.

Indexes

IF-MIBifIndex ATM-MIBatmVclVpi ATM-MIBatmVclVci

Column	Syntax	OID
atmConfVcPolicing Policing method desired for this VCL.	Enumerationr/w Enumerated Values: 1 none 2 police 3 monitor 4 shaping 5 policingAndShaping 255 notApplicable	.1.3.6.1.4.1.164.12.3.2.1.4.1.1
atmConfVcCCAdminStatus up(2) - Activate Continuity Check (CC). down(3) - Deactivate CC. source(4) - Activate OAM CC(Continuity Check) of local agent ( start sending Oam cells to the remote side ). sink(5) - Activate CC of r…	Enumerationr/w Enumerated Values: 2 up 3 down 4 source 5 sink 6 listenToActivationCells 7 originateActivationCells	.1.3.6.1.4.1.164.12.3.2.1.4.1.2
atmConfVcLoopbackAdminStatus up(2) - Start loopback OAM cells. down(3) - Stop sending loopback OAM cells. For ace2002: up(2) - Transmitting LB cells with llid all ones (i.e. FFFF..FF) down(3) - Not transmitting LB cells. …	Enumerationr/w Enumerated Values: 2 up 3 down 4 llid 5 segment 6 endToEnd 7 segmentLlid 8 endToEndLlid	.1.3.6.1.4.1.164.12.3.2.1.4.1.3
atmConfVcLoopbackSinkAddress Destination address. For ace101: 2 bytes are used. For ace2002: 16 bytes are used.	OctetStringr/w Constraints: range: 2-20	.1.3.6.1.4.1.164.12.3.2.1.4.1.4
atmConfVcCongestionControl Each bit indicates a selection of one option as the following description. All combinations are possible and legal. The codes are: 1 - EPD 2 - CLP 4 - EFCI. For ace2002: 1 - Packet Discard.	OctetStringr/w	.1.3.6.1.4.1.164.12.3.2.1.4.1.5
atmConfVcCCDirection both(2) - Agent sends OAM CC cells and checks received OAM CC cells. none(3) - Agent does not send and does not check received OAM CC cells. source(4)- Agent sends OAM CC cells. sink(5) - Agent checks received OAM CC …	Enumerationr/w Enumerated Values: 2 both 3 none 4 source 5 sink	.1.3.6.1.4.1.164.12.3.2.1.4.1.6
atmConfVcCreationTime A date-time in which the VC was created.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.164.12.3.2.1.4.1.7
atmConfVcOamSupport OAM support mode, which determines the device location in a segment wise. endToEndAndSegment - In this mode the OAM cells are generated before the ABM (ATM Buffer Manager), so …	Enumerationr/w Enumerated Values: 1 intermediate 2 segmentTermination 3 endToEndTermination 4 endToEndAndSegment	.1.3.6.1.4.1.164.12.3.2.1.4.1.8
atmConfVcCCActivationCtrl manual(1) - CC Activation process is disable activator(2) - ACE-101 initiate CC Activation process listener(3) - ACE-101 wait to CC Activation request from remote side.	Enumerationr/w Enumerated Values: 1 manual 2 activator 3 listener	.1.3.6.1.4.1.164.12.3.2.1.4.1.9
atmConfVcCCOperStatus initial (1) - The CC activation process is not started. up (2) - Continuity Check (CC) activated. down (3) - CC deactivated. source (4) - OAM CC(Continuity Check) of local agent activated. sink (5) - OAM CC of remo…	Enumeration Enumerated Values: 1 initial 2 up 3 down 4 source 5 sink 8 both 9 timeout 10 denied 11 conflict 12 manual	.1.3.6.1.4.1.164.12.3.2.1.4.1.10
atmConfVcLoopbackTraffic This parameter has both command and status meanings: off(2) - Set to 'Off' will Stop traffic loop. Getting this value means that the loop is not running. on (3) - Set to 'On' will start traffic loop. Getting …	Enumerationr/w Enumerated Values: 2 off 3 on	.1.3.6.1.4.1.164.12.3.2.1.4.1.11
atmConfVcLoopbackFailureInd This object allows user to define the Indication that will be created upon a LB cell failure. disabled(2) - no indication will be created. segmentAis(3) - will cause Tx of a segment AIS. segmentRdi(4) - will cause Tx of…	Enumerationr/w Enumerated Values: 2 disabled 3 segmentAis 4 segmentRdi 5 segmentAisAndRdi 6 endToEndAis 7 endToEndRdi 8 endToEndAisAndRdi	.1.3.6.1.4.1.164.12.3.2.1.4.1.12
atmConfVcLoopbackFailureThreshold The number of the LB failures before starting transmission of the Indication defined by atmConfVcLoopbackFailureInd. Range: 1..16. Default: 1.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.4.1.13
atmConfVcOamDirection The direction of OAM cell insertion. downStream(2) - The OAM cell will be inserted in downStream. upStream(3) - The OAM cell will be inserted in upStream.	Enumerationr/w Enumerated Values: 1 notApplicable 2 downStream 3 upStream	.1.3.6.1.4.1.164.12.3.2.1.4.1.14
atmConfVcName VC Name.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.164.12.3.2.1.4.1.15
atmConfVcConnected This object indicates whether this VC is connected and if connected, what is it connected to. Originally, it was read-only.	Enumerationr/w Enumerated Values: 1 notConnected 2 mng 3 bridgePort 4 ds0Bundle 5 atm 6 pw 7 routerInterface 8 qos 9 other 10 logicalMac 11 atmAal2	.1.3.6.1.4.1.164.12.3.2.1.4.1.16
atmConfVcOamDescrIndex This parameter indicates the VCL's OAM Descriptor index, according to the OAM Descriptor Configuration Table.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.4.1.17
atmConfVcNoOfUsages This object indicates the number of times this VCL is used.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.12.3.2.1.4.1.18

The ATM VP Alarm table.

atmNteAlarmVpEntry row .1.3.6.1.4.1.164.12.3.2.1.5.1

An entry in the ATM VP Alarm table.
ifIndex of the ATM layer.

Indexes

IF-MIBifIndex atmNteVpAlarmVpi

Column	Syntax	OID
atmNteVpAlarmVpi The VPI on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.5.1.1
atmNteVpActiveAlarms A Bit String of the active alarms on this VP. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VP AIS 2 - VP Loss Of Cont…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.5.1.2

The ATM VC Alarm table.

atmNteAlarmVcEntry row .1.3.6.1.4.1.164.12.3.2.1.6.1

An entry in the ATM VC Alarm table.
ifIndex of the ATM layer.

Indexes

IF-MIBifIndex atmNteVcAlarmVpi atmNteVcAlarmVci

Column	Syntax	OID
atmNteVcAlarmVpi The VPI of the VC on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.6.1.1
atmNteVcAlarmVci The VCI of the VC on which there is an active alarm.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.6.1.2
atmNteVcActiveAlarms A Bit String of the active alarms on this VC. An up bit (1) means there is an active alarm of this type. A down bit (0) means there is no such alarm. The meaning of the bits is as follows: 1 - VC AIS 2 - VC Loss Of Cont…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.164.12.3.2.1.6.1.3