RAD-LanRger-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
15
Rows
15
Columns
126

lanrangerBootPTable

table
.1.3.6.1.4.1.164.4.2.1.6.4.4 · 1 row entry · 3 columns
Open in standard view 
A list of BootP entries.  The number of entries is up to
BootP current entries, according to the LANRANger model.
lanrangerBootPEntry entry .1.3.6.1.4.1.164.4.2.1.6.4.4.1
BootP parameters per entry of the BootP table.
Indexes
lanrangerBootPIpAddress
Column Syntax OID
lanrangerBootPIpAddress
BootP Ip Address.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.1.6.4.4.1.1
lanrangerBootPIfIndex
The number is the same as the ifIndex of the link.
Enumeration
Enumerated Values:
255notAllocated
 .1.3.6.1.4.1.164.4.2.1.6.4.4.1.2
lanrangerBootPOperation
This object indicates the status of this entry.
active(1) - this entry is currently in use
and will remain so even after the next
reset of the LANRANger.
delete(2) - writing this value to the obj…
Enumerationr/w
Enumerated Values:
1active
2delete
 .1.3.6.1.4.1.164.4.2.1.6.4.4.1.3

lanrangerLinkTable

table
.1.3.6.1.4.1.164.4.2.2.1 · 1 row entry · 16 columns
Open in standard view 
A list of link entries.  The number of entries is
up to 8, according to the LANRANger model.
lanrangerLinkEntry entry .1.3.6.1.4.1.164.4.2.2.1.1
LANRANger-specific parameter values for a link.
Indexes
lanrangerLinkIndex
Column Syntax OID
lanrangerLinkIndex
A unique value for each link, equal to the value of ifIndex.
The value for each link must remain constant at least
from one re-initialization of the network management agent to
the next.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.1.1.1
lanrangerLinkType
The link type .
Enumerationr/w
Enumerated Values:
1synchronous
2asynchronous
3x25FRconfig
4x25FRchannel
5isdn
6frameRelay
7pcmcia
8dm2wire
254notExist
255unknown
 .1.3.6.1.4.1.164.4.2.2.1.1.2
lanrangerLinkState
The link is disabled, enabled or backup.
Enumerationr/w
Enumerated Values:
2disable
3enable
4backup
 .1.3.6.1.4.1.164.4.2.2.1.1.3
lanrangerLinkDTRMode
The link DTR mode.
Enumeration
Enumerated Values:
2off
3on
255unknown
 .1.3.6.1.4.1.164.4.2.2.1.1.4
lanrangerLinkStatus
The link physical status .
Enumeration
Enumerated Values:
1ok
2fail
3rxNoClock
4txProblem
5noCarrierD
255unknown
 .1.3.6.1.4.1.164.4.2.2.1.1.5
lanrangerLinkConnectionStatus
The link connection status.
Enumeration
Enumerated Values:
1fail
2disconnect
3connect
4wait
5down
6trying
7testing
255unknown
 .1.3.6.1.4.1.164.4.2.2.1.1.6
lanrangerLinkNumOfLogLinks
The number of logical links on this physical link.
0 = noLogicalLink
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.1.1.7
lanrangerLinkReset
Setting this attribute to ON will reset the link . Upon completion the value will be set to OFF
Enumerationr/w
Enumerated Values:
2off
3on
 .1.3.6.1.4.1.164.4.2.2.1.1.8
lanrangerLinkRxMaskedFrames
The number of masked frames received on this physical link.
SNMPv2-SMICounter32
Textual Convention: SNMPv2-SMICounter32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.1.1.9
lanrangerLinkLayer2Type
The link layer 2 type indicates whether the link is Bridge
or Router and specifies the Router's type.
Enumerationr/w
Enumerated Values:
1unknown
2bridge
3ipRouter
4ipxRouter
5ipAndIpxRouter
6bRouter
7ipBrouter
8ipxBrouter
9ipAndIpxBrouter
10bridgeAndStp
 .1.3.6.1.4.1.164.4.2.2.1.1.10
lanrangerLinkLayer3Type
The link layer 3 type indicates the protocol type.
Enumerationr/w
Enumerated Values:
1unknown
2proprietary
3terminalServer
30slip
31cSlip
40ppp
41rfc1490
42hdlcFraming
43mlPpp
 .1.3.6.1.4.1.164.4.2.2.1.1.11
lanrangerBackupLink
The backup link interface index located in the two LSB bytes.
If the link is FR type, the two MSB will contain a DLCi number.
For other link types the two MSB will equal to 0.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.1.1.12
wrWanThrottle
Throttle controls the baud rate of the WAN.
For example if we have a WAN rate of 2M but we want only 1/2 M as
the baud rate we set the Wan Throttle to 512k.

These are the values:
Full (2),
1M (3),
512k (…
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.1.1.13
wrIpTransparentMode
This parameter shows whether the IP Transparent mode is enabled.
When this mode is enabled, all frames (including broadcast and multicast frames)
are forwarded from E1/T1 to LAN and from LAN to E1/T1.
Enumerationr/w
Enumerated Values:
1notApplicable
2disable
3enableAll
 .1.3.6.1.4.1.164.4.2.2.1.1.14
wrIpTransparentGateway
The gateway used for transparent IP.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.2.1.1.15
lanrangerLinkProtocolType
This parameter indicates the routing protocol running on this Interface.
Enumerationr/w
Enumerated Values:
1notApplicable
2noRoutingProtocol
3rip1
4rip2
5rip1OrRip2
6ospf
 .1.3.6.1.4.1.164.4.2.2.1.1.16

lanrangerLinkConnTable

table
.1.3.6.1.4.1.164.4.2.2.2.3 · 1 row entry · 9 columns
Open in standard view 
A list of Connection entries.  The number of entries is
up to Max entries, according to the LANRANger model.
lanrangerLinkConnEntry entry .1.3.6.1.4.1.164.4.2.2.2.3.1
Information about LANRANger Connection.
Indexes
lanrangerLinkConnPhysLink lanrangerLinkConnAid lanrangerLinkConnMacAddr
Column Syntax OID
lanrangerLinkConnPhysLink
The lanrangerLinkIndex for the physical link with which this logical link is associated.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.2.3.1.1
lanrangerLinkConnAid
A unique value for each logical link. The maximum number
of logical links is 256, according to the LANRANger model.
The value for each logical link must remain constant at least
from one re-initialization of the ne…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.2.3.1.2
lanrangerLinkConnMacAddr
The MAC address of the device that the logical link is connected to
on the remote LAN.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.164.4.2.2.2.3.1.3
lanrangerLinkConnStatus
The link connection status.
Enumeration
Enumerated Values:
1unknown
2none
3fail
4connect
5wait
6down
 .1.3.6.1.4.1.164.4.2.2.2.3.1.4
lanrangerLinkConnDeviceType
The type of device that the logical link is connected to on the remote LAN.
Enumeration
Enumerated Values:
1tre1
2tre8
3tre1D
4tre8D
5tre8M
6rrTre
7rrTre1D
8rrTre8D
9iTre1
10iTre2
11mpTre8
12kTre8
13treRasA
14treRasS
15trePCAsync
16trePCSync
17mbe1
18mbe8
19mbe1D
20mbe8D
21ete8M
22iEre1
23iEe2
24mpMbe8
25kMbe8
26mbePCAsync
27mbePCSync
28mbeRasA
29mbeRasS
255other
 .1.3.6.1.4.1.164.4.2.2.2.3.1.5
lanrangerLinkConnDeviceName
The logical name of the device that the logical link is connected to on the remote LAN.
SNMPv2-TCDisplayString
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.2.3.1.6
lanrangerLinkConnDeviceSWVer
SW Version of the device that the logical link is
connected to, on the remote LAN.
SNMPv2-TCDisplayString
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.2.3.1.7
lanrangerLinkConnNumLanStation
The number of stations of the remote LAN.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.2.3.1.8
lanrangerLinkSyncStatus
The Sync link status.
Enumeration
Enumerated Values:
1synchronized
2syncNotObtained
3waitForSync
4codDisconnected
5lcp
6ip
7ipvj
8ipx
9ipIpx
10ipvj-ipx
11mlPpp
12mlPpp-ip
13mlPpp-ip-ipvj
14mlPpp-ip-ipx
15mlPpp-ipvj-ipx
16mlPpp-ipx
17frUp
18frDown
19dlciUp
20dlciDown
21extLoop
22ipcp
23lcpIpcp
24redAlarm
26yellowAlarm
27localSyncLoss
28remoteSyncLoss
29networkLoop
30networkLoopRedAlarm
31networkLoopYelAlarm
32networkLocSyncLoss
33networkRemSyncLoss
34fdlLoop
35fdlLoopRedAlarm
36fdlLoopYellowAlarm
37fdlLoopLocSyncLoss
38fdlLoopRemSyncLoss
39loopback
40loopbackLocSyncLoss
41loopbackRemSyncLoss
 .1.3.6.1.4.1.164.4.2.2.2.3.1.9

lanrangerModemTable

table
.1.3.6.1.4.1.164.4.2.2.3 · 1 row entry · 11 columns
Open in standard view 
A list of Modem entries.  The number of entries is
up to ifIndex.
lanrangerModemEntry entry .1.3.6.1.4.1.164.4.2.2.3.1
LANRANger-specific parameter values for a Modem.
Indexes
lanrangerModemLinkIndex
Column Syntax OID
lanrangerModemLinkIndex
A list of asynchronous ports of the link, according to
ifIndex.
Synchronous ports will not appear in this table. Their
port number will be skipped.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.3.1.1
lanrangerModemName
The Modem Name identifier for MBE/TRE.
Up to 50 characters.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.3.1.2
lanrangerModemSettingString
Modem setting String.
Up to 80 characters.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.3.1.3
lanrangerModemAutobaudingSpeed
Enable or disable autobauding.
When the Autobauding feature is enabled, the MBE/TRE
automatically ranges over various Baud rates, starting
with 115.2 Kbps, until the correct Baud rate of the modem
is detected.
Enumerationr/w
Enumerated Values:
2disable
3enable
 .1.3.6.1.4.1.164.4.2.2.3.1.4
lanrangerModemResetBeforeSetup
Reset the modem before setup is performed.
It is recommended to reset the modem before modem setup
session.
Enumerationr/w
Enumerated Values:
2no
3yes
 .1.3.6.1.4.1.164.4.2.2.3.1.5
lanrangerModemAnalyzeAnswers
Enable this option if a modem using non-standard answering is used.
When this mode is enabled, the MBE/TRE awaits modem answers
'CONNECT', 'CARRIER', or 'OK', after it transmits a modem command.
Modem answers acknowledg…
Enumerationr/w
Enumerated Values:
2disable
3enable
 .1.3.6.1.4.1.164.4.2.2.3.1.6
lanrangerModemSpeaker
Toggle the Modem Speaker On or Off .
Enumerationr/w
Enumerated Values:
2off
3on
 .1.3.6.1.4.1.164.4.2.2.3.1.7
lanrangerModemDialingNumber
Various command switches listed in Modem Dialing Number Menu
allows selection of tone, pulse-dialing, or various wait states.
P - Set Pulse dialing number .
T - Set Tone dialing number .
W - Wait for dialing tone befor…
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.3.1.8
wrLocalDialBackNumber
This is the number that the Remote Modem will use to call the local
Modem at Dial Back.

Various command switches listed in Modem Dialing Number Menu
allows selection of tone, pulse-dialing, or various wai…
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.3.1.9
wrRingsBeforeAnswer
Determines which ring the modem will wait to answer the
phone on.
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.3.1.10
lanrangerModemDialRetries
The number of dialing retries requested.
Default = 0
Integer32r/w
Constraints:
range: 0-8
 .1.3.6.1.4.1.164.4.2.2.3.1.11

lanrangerLinkPktSwTable

table
.1.3.6.1.4.1.164.4.2.2.4 · 1 row entry · 7 columns
Open in standard view 
A list of X.25/FR modules entries.  The number of entries is
up to ifIndex.
lanrangerLinkPktSwEntry entry .1.3.6.1.4.1.164.4.2.2.4.1
LANRANger-specific parameter values for X.25/FR modules.
Indexes
lanrangerLinkPktSwIndex
Column Syntax OID
lanrangerLinkPktSwIndex
A unique value for each X.25/FR of the link, according to
numbering system of ifIndex. The maximum number of links is
ifIndex. The value for each link must remain constant at
least from one re-initialization of the n…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.4.1.1
lanrangerLinkPktSwType
Packet Switch Type.
Enumeration
Enumerated Values:
1x25FRChannel
2x25FRConfig
 .1.3.6.1.4.1.164.4.2.2.4.1.2
lanrangerLinkPktSwControlSignal
Packet Switch control command.
Enumerationr/w
Enumerated Values:
2off
3on
 .1.3.6.1.4.1.164.4.2.2.4.1.3
lanrangerLinkPktSwSpeed
The Pkt Switch port's speed in bits per second.
Range: 1200bps .. 1544000bps
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.4.1.4
lanrangerLinkPktSwConfigParity
The Pkt Switch Config port's character parity bit.
Applicable only for x25FRConfigChannel. For x25FRChannel
the value notApplicable applies.
Enumerationr/w
Enumerated Values:
1none
2odd
3even
255notApplicable
 .1.3.6.1.4.1.164.4.2.2.4.1.5
lanrangerLinkPktSwConfigStopBit
The Pkt Switch Config port's number of stop bits.
Applicable only for x25FRConfigChannel. For x25FRChannel
the value notApplicable applies.
Enumerationr/w
Enumerated Values:
1one
2two
255notApplicable
 .1.3.6.1.4.1.164.4.2.2.4.1.6
lanrangerLinkPktSwResetModule
Reset command to Pkt Switch module.
Applicable only for x25FRChannel.
The command will have no effect on x25FRConfigChannel.
Enumerationr/w
Enumerated Values:
2off
3on
 .1.3.6.1.4.1.164.4.2.2.4.1.7

wrPPPTable

table
.1.3.6.1.4.1.164.4.2.2.5 · 1 row entry · 16 columns
Open in standard view 
This table contains only parameters that do not exist in the PPP
standard MIBS.
The table contains a list of PPP entries.  
The number of entries is up to ifIndex.
wrPPPEntry entry .1.3.6.1.4.1.164.4.2.2.5.1
LANRANger-specific parameter values for a PPP.
Indexes
IF-MIBifIndex
Column Syntax OID
wrPPPCompressionHeaderField
This configuration option provides a method to negotiate the
compression of the Data Link Layer Address and Control fields.
This configuration option is sent to inform the peer that the
implementation can receive compre…
Enumerationr/w
Enumerated Values:
2compressionOff
3compressionOn
 .1.3.6.1.4.1.164.4.2.2.5.1.1
wrPPPCompressionProtocolFields
This configuration option provides a method to negotiate the
compression of the PPP Protocol field. This configuration option
is sent to inform the peer that the implementation can receive
such single octet Protocol fie…
Enumerationr/w
Enumerated Values:
2compressionOff
3compressionOn
 .1.3.6.1.4.1.164.4.2.2.5.1.2
wrPPPSTACCompressionType
The PPP compression control protocol provides a method to negotiate
and utilize compression protocol over PPP encapsulated links.
These are Different types of data compression algorithm for PPP
encapsulated packets.
Enumerationr/w
Enumerated Values:
1disable
2noHistory
3lCB
4sequence
5extended
 .1.3.6.1.4.1.164.4.2.2.5.1.3
wrPPPAuthProtocol
The type of authentication protocol being used. The left parameter
is the maximum authentication, the right parameter is minimum authentication.
Enumerationr/w
Enumerated Values:
1noneNone
2chapNone
3chapPap
4chapChap
5papNone
6papPap
 .1.3.6.1.4.1.164.4.2.2.5.1.4
wrPPPSecurityType
Type of unit.
Enumerationr/w
Enumerated Values:
1host
2guest
 .1.3.6.1.4.1.164.4.2.2.5.1.5
wrPPPUserName
PPP User name.
OctetStringr/w
Constraints:
range: 0-36
 .1.3.6.1.4.1.164.4.2.2.5.1.6
wrPPPPassword
PPP Password .
OctetStringr/w
Constraints:
range: 0-36
 .1.3.6.1.4.1.164.4.2.2.5.1.7
wrPPPLinkActiveTime
PPP link active time in seconds
Values range: 2 - 900.
Default value = 2
SNMPv2-SMIInteger32r/w
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.2.5.1.8
wrPPPIPCPSubnetMaskNegotiation
This object indicates the ifIndex of the link (LAN port)
through which IPCP Subnet Mask negotiation is allowed.
The distinguished value of zero may be used if no link
is enabled for IPCP Subnet Mask negotiation.
…
IF-MIBInterfaceIndexOrZeror/w
Textual Convention: IF-MIBInterfaceIndexOrZero Integer32
Type Constraints:
range: 0..2147483647
 .1.3.6.1.4.1.164.4.2.2.5.1.9
wrPPPLinkControlProtocolStatus
PPP Link Control Protocol(LCP) Status
Enumeration
Enumerated Values:
1notApplicable
2close
3open
 .1.3.6.1.4.1.164.4.2.2.5.1.10
wrPPPAuthenticationStatus
PPP Authentication status.
Enumeration
Enumerated Values:
1notApplicable
2failed
3passed
 .1.3.6.1.4.1.164.4.2.2.5.1.11
wrPPPIpcpStatus
IPCP (IP Control Protocol) status.
Enumeration
Enumerated Values:
1notApplicable
2close
3open
 .1.3.6.1.4.1.164.4.2.2.5.1.12
wrPPPAssignedIPAddress
IP Address assigned by PPP.
SNMPv2-SMIIpAddress
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.2.5.1.13
wrPPPActualAuthProtocol
The Actual type of Authentication Protocol that is used.
Enumeration
Enumerated Values:
1none
2pap
3chap
 .1.3.6.1.4.1.164.4.2.2.5.1.14
wrPPPIpTranslationMode
This object enables the IP Translation Mode.
Enumerationr/w
Enumerated Values:
2disable
3enable
 .1.3.6.1.4.1.164.4.2.2.5.1.15
wrPPPTranslatedIpAddr
This object represents the Translated IP Address.
It is relevant only when IP Translation Mode is 'enable'.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.2.5.1.16

wrMLPPPTable

table
.1.3.6.1.4.1.164.4.2.2.6 · 1 row entry · 3 columns
Open in standard view 
This table contains a list of ML-PPP entries.
wrMLPPPEntry entry .1.3.6.1.4.1.164.4.2.2.6.1
Specific parameter values for a ML-PPP.
Indexes
IF-MIBifIndex
Column Syntax OID
wrMLPPPEpDiscriminatorEnable
Indicates whether the Endpoint Discriminator Option is enabled.

The Endpoint Discriminator Option represents identification of the
system transmitting the packet. This option advises a system that
th…
Enumerationr/w
Enumerated Values:
2no
3yes
 .1.3.6.1.4.1.164.4.2.2.6.1.1
wrMLPPPReorderingEnable
Indicates whether packets reordering option is enabled.
yes - packets received from MLPPP not in order are
reordered, according to sequence number,
before being transmitted to egress port.
no - received p…
Enumerationr/w
Enumerated Values:
1notApplicable
2no
3yes
 .1.3.6.1.4.1.164.4.2.2.6.1.2
wrMLPPPTxQueueSize
Indicates the number of frames in the Tx Queue.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.6.1.3

pPPoETable

table
.1.3.6.1.4.1.164.4.2.2.7.1 · 1 row entry · 19 columns
Open in standard view 
The PPPoE (Point-to-Point Protocol over Ethernet) Table.
pPPoEEntry entry .1.3.6.1.4.1.164.4.2.2.7.1.1
An entry in the PPPoE Table.
Indexes
pPPoECnfgIdx pPPoEID
Column Syntax OID
pPPoECnfgIdx
Usually the ifIndex of the PPP link the PPPoE session is on.
Some applications may use this index otherwise.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.1
pPPoEID
PPPoE session unique identifier.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.2
pPPoERowStatus
This object enables the user to create/delete entries in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.164.4.2.2.7.1.1.3
pPPoEACName
The access concentrator
the PPPoE session should be established with.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.7.1.1.4
pPPoEServiceName
The service requested on the PPPoE session.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.7.1.1.5
pPPoEEntityPointer
This parameter represents the entity (interface/port etc)
that is connected to this PPPoE.

The value of this parameter is a pointer to an existing row of a table,
where the entity connected to this PP…
SNMPv2-TCRowPointerr/w
Textual Convention: SNMPv2-TCRowPointer ObjectIdentifier
 .1.3.6.1.4.1.164.4.2.2.7.1.1.6
pPPoESessionStatus
notApplicable - none of the other states applies
down - session not established
up - session established
lowerLayerDown - session not established due to lower layer failure
adminDisabled - a user has disabled the session
Enumeration
Enumerated Values:
1notApplicable
2down
3up
4lowerLayerDown
5adminDisabled
 .1.3.6.1.4.1.164.4.2.2.7.1.1.7
pPPoESessionID
This object represents PPPoE Session ID.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.8
pPPoERemoteMacAddr
This object represents the MAC Address of the Access Concentrator,
with which the PPPoE session is established.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.164.4.2.2.7.1.1.9
pPPoENoOfUsages
This object represents the number of times this PPPoE is used.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.10
pPPoESchedRestartMode
This object represents Scheduled Restart Mode.
Enumerationr/w
Enumerated Values:
1notApplicable
2disable
3enable
 .1.3.6.1.4.1.164.4.2.2.7.1.1.11
pPPoESchedRestartTime
This object represents Scheduled Restart Time.
It is relevant only when Scheduled Restart Mode is 'enable'.
SNMPv2-TCDisplayStringr/w
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.7.1.1.12
pPPoESchedRestartRandomRange
This object represents Scheduled Restart Random Range (in seconds).
It is relevant only when Scheduled Restart Mode is 'enable'.

A scheduled restart Random VALUE (number of seconds) is selected
within thi…
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.13
pPPoESchedRestartActualTime
This object represents Scheduled Restart Actual Time.
It is relevant only when Scheduled Restart Mode is 'enable'.
For calculation of this time - see pPPoESchedRestartRandomRange.
SNMPv2-TCDisplayString
Textual Convention: SNMPv2-TCDisplayString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.7.1.1.14
pPPoEInitDelayRandomRange
This object represents the Initialization Delay Random Range (in seconds).
An initialization DELAY (number of seconds) is selected within this Random Range.

This DELAY is used to delay the initialization …
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.15
pPPoEInitActualDelay
This object represents Initialization Delay (in seconds),
as selected within Initialization Delay Random Range (pPPoEInitDelayRandomRange).
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.16
pPPoEVlanTagging
This object represents the VLAN Tagging.
Enumerationr/w
Enumerated Values:
1notApplicable
2untag
3tag
 .1.3.6.1.4.1.164.4.2.2.7.1.1.17
pPPoEVlanId
This object represents the VLAN ID.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.18
pPPoEVlanPriority
This object represents the VLAN Priority.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.1.1.19

pppoeClientReceivedTagsTable

table
.1.3.6.1.4.1.164.4.2.2.7.2 · 1 row entry · 3 columns
Open in standard view 
This table contains the PPPoE tags
received in the offer (PADO packet) of the access concentrator
with which a PPPoE session has been established.
pppoeClientReceivedTagsEntry entry .1.3.6.1.4.1.164.4.2.2.7.2.1
Each entry contains the details of one PPPoE tag.
Indexes
pPPoECnfgIdx pPPoEID pppoeClientReceivedTagNumber
Column Syntax OID
pppoeClientReceivedTagNumber
A running index. 1 for the first tag received
in the PADO packet, 2 for the second, and so on.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.2.1.1
pppoeClientReceivedTagType
The TAG_TYPE of the PPPoE tag in the received packet.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.7.2.1.2
pppoeClientReceivedTagValue
The TAG_VALUE of the PPPoE tag in the received packet.
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.7.2.1.3

pppSecurityTable

table
.1.3.6.1.4.1.164.4.2.2.8 · 1 row entry · 7 columns
Open in standard view 
This table contains user credentials
used by various methods (CHAP, PAP...)
during the PPP authentication phase.
pppSecurityEntry entry .1.3.6.1.4.1.164.4.2.2.8.1
Each entry contains one authentication parameter or more,
depending of the entry's type.
Indexes
IF-MIBifIndex pppSecurityType pppSecurityPriority
Column Syntax OID
pppSecurityType
The type of the credentials in this entry.
chapHostname - hostname to send to the authenticator in CHAP
authentication, instead of the (by default) device sysName
chapPassword - default password to use in CHAP authe…
Enumeration
Enumerated Values:
1chapHostname
2chapPassword
3papUsername
 .1.3.6.1.4.1.164.4.2.2.8.1.1
pppSecurityPriority
If there are multiple entries of the same type, one with
lower priority has precedence over one with higher priority.
SNMPv2-SMIUnsigned32
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.8.1.2
pppSecurityRowStatus
User credentials are added and removed by users using this object.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.164.4.2.2.8.1.3
pppSecurityDirection
The direction in which the credentials in this entry are used.
localToRemote - the device is authenticated by a peer
RemoteToLocal - The device authenticates a peer
Enumerationr/w
Enumerated Values:
1localToRemote
2remoteToLocal
 .1.3.6.1.4.1.164.4.2.2.8.1.4
pppSecurityIdentity
A string representing name, such as hostname or username,
to be used in the PPP authentication phase.
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.8.1.5
pppSecuritySecret
A password to be used in the PPP authentication phase.
The password is always saved in an encrypted form; if a
user sets a clear password, the device must encrypt it before
saving it in this object.
This object always r…
SNMP-FRAMEWORK-MIBSnmpAdminStringr/w
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.8.1.6
pppSecuritySecretType
This object is used by users to denote whether the string set
in pppSecuritySecret is a clear or encrypted password. The device
sets it to 'off' after saving the password in pppSecuritySecret.
Enumerationr/w
Enumerated Values:
1off
2clear
3encrypted
 .1.3.6.1.4.1.164.4.2.2.8.1.7

pppLinkStatusXTable

table
.1.3.6.1.4.1.164.4.2.2.9 · 1 row entry · 15 columns
Open in standard view 
This table contains PPP monitoring objects.
It augments the standard pppLinkStatusTable (rfc 1471).
pppLinkStatusXEntry entry .1.3.6.1.4.1.164.4.2.2.9.1
Each entry contains monitoring objects of one PPP link.
Indexes
No indexes recorded
Column Syntax OID
pppLinkStatusXLcpState
LCP phase state.
PppState
Textual Convention: PppState Enumeration
Type Values:
1initial
2starting
3closed
4stopped
5closing
6stopping
7requestSent
8ackReceived
9ackSent
10opened
 .1.3.6.1.4.1.164.4.2.2.9.1.1
pppLinkStatusXUsAuthProtocol
The method used by the peer to authenticate the device.
PppAuthMethod
Textual Convention: PppAuthMethod Enumeration
Type Values:
1noAuth
2chap
3pap
 .1.3.6.1.4.1.164.4.2.2.9.1.2
pppLinkStatusXUsAuthState
The state of the process of the peer authenticating the device.
PppAuthStatus
Textual Convention: PppAuthStatus Enumeration
Type Values:
1notApplicable
2initial
3completed
4inProgress
5failed
 .1.3.6.1.4.1.164.4.2.2.9.1.3
pppLinkStatusXUsAuthIdentity
The identity used in the process of the peer authenticating the
device, or empty string if the peer does not authenticate the device.
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.9.1.4
pppLinkStatusXPeerAuthProtocol
The method used to authenticate the peer.
PppAuthMethod
Textual Convention: PppAuthMethod Enumeration
Type Values:
1noAuth
2chap
3pap
 .1.3.6.1.4.1.164.4.2.2.9.1.5
pppLinkStatusXPeerAuthState
The state of the process of authenticating the peer.
PppAuthStatus
Textual Convention: PppAuthStatus Enumeration
Type Values:
1notApplicable
2initial
3completed
4inProgress
5failed
 .1.3.6.1.4.1.164.4.2.2.9.1.6
pppLinkStatusXPeerAuthIdentity
The identity used in the process of authenticating the peer,
or empty string if the peer is not required to be authenticated.
SNMP-FRAMEWORK-MIBSnmpAdminString
Textual Convention: SNMP-FRAMEWORK-MIBSnmpAdminString OctetString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.164.4.2.2.9.1.7
pppLinkStatusXIpcpState
IPCP phase state.
PppState
Textual Convention: PppState Enumeration
Type Values:
1initial
2starting
3closed
4stopped
5closing
6stopping
7requestSent
8ackReceived
9ackSent
10opened
 .1.3.6.1.4.1.164.4.2.2.9.1.8
pppLinkStatusXIpcpLocalIp
Address of this device, used for encapsulating IPv4 packets
in the PPP session.
If no IP address is used or if IPCP negotiation was not completed
this object is set to 0.
INET-ADDRESS-MIBInetAddressIPv4
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.2.9.1.9
pppLinkStatusXIpcpLocalIpNegotiated
This object is true if the IPv4 address in pppLinkStatusXIpcpLocalIp
was negotiated with the peer, and false oterwise.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.164.4.2.2.9.1.10
pppLinkStatusXIpcpRemoteIp
Address of remote device, used for encapsulating IPv4 packets
in the PPP session.
If no IP address is used or if IPCP negotiation was not completed
this object is set to 0.
INET-ADDRESS-MIBInetAddressIPv4
Textual Convention: INET-ADDRESS-MIBInetAddressIPv4 OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.164.4.2.2.9.1.11
pppLinkStatusXIpv6cpState
IPV6CP phase state.
PppState
Textual Convention: PppState Enumeration
Type Values:
1initial
2starting
3closed
4stopped
5closing
6stopping
7requestSent
8ackReceived
9ackSent
10opened
 .1.3.6.1.4.1.164.4.2.2.9.1.12
pppLinkStatusXIpv6cpLocalIp
Address of this device, used for encapsulating IPv6 packets
in the PPP session.
If no IP address is used or if IPV6CP negotiation was not completed
this object is set to 0.
INET-ADDRESS-MIBInetAddressIPv6
Textual Convention: INET-ADDRESS-MIBInetAddressIPv6 OctetString
Type Constraints:
range: 16
 .1.3.6.1.4.1.164.4.2.2.9.1.13
pppLinkStatusXIpv6cpLocalIpNegotiated
This object is true if the IPv6 address in pppLinkStatusXIpv6cpLocalIp
was negotiated with the peer, and false oterwise.
SNMPv2-TCTruthValue
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.164.4.2.2.9.1.14
pppLinkStatusXIpv6cpRemoteIp
Address of remote device, used for encapsulating IPv6 packets
in the PPP session.
If no IP address is used or if IPV6CP negotiation was not completed
this object is set to 0.
INET-ADDRESS-MIBInetAddressIPv6
Textual Convention: INET-ADDRESS-MIBInetAddressIPv6 OctetString
Type Constraints:
range: 16
 .1.3.6.1.4.1.164.4.2.2.9.1.15

pppLinkConfigXTable

table
.1.3.6.1.4.1.164.4.2.2.10 · 1 row entry · 4 columns
Open in standard view 
This table is used to configure PPP sessions.
It augments the standard pppLinkConfigTable (rfc 1471).
pppLinkConfigXEntry entry .1.3.6.1.4.1.164.4.2.2.10.1
Each entry contains configuration of one PPP link.
Indexes
No indexes recorded
Column Syntax OID
pppLinkConfigXLowerLayer
ifIndex of the lower layer (e.g. Ethernet) the PPP link is bound to,
or 0 if the PPP link is not bound to a lower layer.
SNMPv2-SMIUnsigned32r/w
Textual Convention: SNMPv2-SMIUnsigned32 Unsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.164.4.2.2.10.1.1
pppLinkConfigXRefuseChap
If true, the device will not accept being authenticated by CHAP.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.164.4.2.2.10.1.2
pppLinkConfigXRefuseNoAuth
If true, the device will not accept not being authenticated.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.164.4.2.2.10.1.3
pppLinkConfigXRefusePap
If true, the device will not accept being authenticated by PAP.
SNMPv2-TCTruthValuer/w
Textual Convention: SNMPv2-TCTruthValue Enumeration
Type Values:
1true
2false
 .1.3.6.1.4.1.164.4.2.2.10.1.4

lanrangerStationTable

table
.1.3.6.1.4.1.164.4.2.3.1 · 1 row entry · 5 columns
Open in standard view 
A table that contains information about the stations 
on the remote LAN(s).
A remote LANRANger contains a list of stations on its 
LAN, while a main LANRANger contains a list of 
stations at all the remote sites it is connected to.
lanrangerStationEntry entry .1.3.6.1.4.1.164.4.2.3.1.1
Information about a specific station, that the LANRANger
lists as being on a remote LAN.
Indexes
lanrangerStationPhysLink lanrangerStationLogLink lanrangerStationAddress
Column Syntax OID
lanrangerStationPhysLink
The number of the physical link that is connected to the
remote LAN on which the station with the associated
instance of lanrangerStationAddress is located. The number
is the same as the ifIndex of the link. The valu…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.1.1.1
lanrangerStationLogLink
The number of the logical link that is connected
to the remote LAN on which the station with the associated
instance of lanrangerStationAddress is located. The value
will be zero on a remote LANRANger.
noLogicLink = …
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.1.1.2
lanrangerStationAddress
The unicast MAC address of a station that the LANRANger
lists as being on a remote LAN.
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.164.4.2.3.1.1.3
lanrangerStationStatus
The status of this entry. The meanings of the
values are:
unknown(1) :
learned(2) : the value of the corresponding
instance of lanrangerStationAddress was
learned and is being used.
…
Enumeration
Enumerated Values:
1unknown
2learned
3self
4static
 .1.3.6.1.4.1.164.4.2.3.1.1.4
lanrangerStationSpoofingStatus
The spoofing status of this entry.
Enumeration
Enumerated Values:
2off
3on
 .1.3.6.1.4.1.164.4.2.3.1.1.5

lanrangerPermanentTable

table
.1.3.6.1.4.1.164.4.2.3.4.3 · 1 row entry · 4 columns
Open in standard view 
A table containing address information
configured into the LANRANger by (local or network)
management, specifying addresses on a remote LAN. 
This table objects can be set only on a Remote LANRANger.
lanrangerPermanentEntry entry .1.3.6.1.4.1.164.4.2.3.4.3.1
Address information configured into the remote LANRANger
by (local or network) management specifying addresses
on a remote LAN.
Indexes
lanrangerPermanentIfIndex lanrangerPermanentLogLink lanrangerPermanentAddress
Column Syntax OID
lanrangerPermanentIfIndex
The number of the physical link that is connected to
the remote LAN, on which the station with the
associated instance of lanrangerStationAddress is
located.
The number is the same as the ifIndex of the link.
This da…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.4.3.1.1
lanrangerPermanentLogLink
The number of the logical link that is connected to the
remote LAN, on which the station with the associated
instance of lanrangerPermanentAddress is located.
The value will be noLogicLink on a remote LANRANger.
This d…
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.4.3.1.2
lanrangerPermanentAddress
The MAC address entered by management to this entry.
Only the remote LANRANger will accept Set for this object !
----------------
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.164.4.2.3.4.3.1.3
lanrangerPermanentOperation
This object indicates the status of this entry.
active(1) - this entry is currently in use
and will remain so even after the next
reset of the LANRANger.
delete(2) - writing this value to the obj…
Enumerationr/w
Enumerated Values:
1active
2delete
 .1.3.6.1.4.1.164.4.2.3.4.3.1.4

lanrangerSpoofingTable

table
.1.3.6.1.4.1.164.4.2.3.6.3 · 1 row entry · 4 columns
Open in standard view 
A list of Spoofing entries. The number of entries is 
up to the current number of entries, according to the 
LANRANger model. 
Only the LOCAL LANRANger will show this table !
         ---------------
lanrangerSpoofingEntry entry .1.3.6.1.4.1.164.4.2.3.6.3.1
Spoofing parameters per entry of the Spoofing table.
Indexes
lanrangerSpoofingGroup lanrangerSpoofingMacAddress
Column Syntax OID
lanrangerSpoofingGroup
The spoofing group.
Only the LOCAL Lanranger will show this table !
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.6.3.1.1
lanrangerSpoofingMacAddress
MAC Address of the Remote Lanrangers.
Only the LOCAL Lanranger will show this table !
SNMPv2-TCMacAddress
Textual Convention: SNMPv2-TCMacAddress OctetString
Type Constraints:
range: 6
 .1.3.6.1.4.1.164.4.2.3.6.3.1.2
lanrangerSpoofingAging
Aging time defined for a whole group, in minutes.
Only the LOCAL Lanranger will show this table !
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.6.3.1.3
lanrangerSpoofingTimeLeft
Time until aging expires, per station, in minutes.
Only the LOCAL Lanranger will show this table !
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.164.4.2.3.6.3.1.4