This trap is sent whenever the status of tftp changed.
clkSrcChangeTrap
.1.3.6.1.4.1.164.6.1.0.10
This trap is sent upon any change in Clock Source.
systemSerialPortDisabled
.1.3.6.1.4.1.164.6.1.0.100
This trap is sent if the serial port is disabled.
systemSerialPortEnabled
.1.3.6.1.4.1.164.6.1.0.101
This trap is sent if the serial port is enabled.
systemFactoryDefaultButtonPushed
.1.3.6.1.4.1.164.6.1.0.102
This trap is sent if the factory default button has been pressed
for five seconds, triggering the factory-default command.
agnUploadDataTrap
.1.3.6.1.4.1.164.6.1.0.11
This trap is sent upon an upload data session termination.
For more details see product specification.
enrollmentTrap
.1.3.6.1.4.1.164.6.1.0.12
This trap is a periodically trap, which sent to manager
untill Agent get any response (Get or Set) from this manager.
agnPowerFailureTrap
.1.3.6.1.4.1.164.6.1.0.13
This trap is sent upon power failure. It is applicable for
the following devices:
1. Devices having one PS unit, which sense the failure in advance,
and still have time to send this trap before it goes off.
2. Devices having 2 PS units and send this trap in order to notify a
failure in one of the units.
agnFanFailureTrap
.1.3.6.1.4.1.164.6.1.0.14
This trap is sent upon fan failure/recovery.
agnSystemParameterChangeTrap
.1.3.6.1.4.1.164.6.1.0.15
This trap is sent upon any change of the systemParameter value.
agnConfigDBChecksumError
.1.3.6.1.4.1.164.6.1.0.16
This trap indicates that the database currently
stored in the non-volatile memory of the device is corrupted
agnAlarmBufferOverflow
.1.3.6.1.4.1.164.6.1.0.17
This trap indicates that the quantity of
alarm messages which have been written
in the alarm buffer, since the last clear command,
exceeds predefined threshold. (Buffer size)
The new alarms are overwriting the oldest alarms
(the first alarms written in the buffer).
For LA-110,threshold value is 200 alarms.
agnAlarmBufferClear
.1.3.6.1.4.1.164.6.1.0.18
This trap indicates that
alarm buffer has been cleared.
agnParametersValueChanged
.1.3.6.1.4.1.164.6.1.0.19
This trap indicates that due to software upgrade,
some of the parameters are assigned new values
agnStatusChangeTrap
.1.3.6.1.4.1.164.6.1.0.2
This trap is sent whenever the state of the entity the agent is
responsible for changed.
TDM devices will send agnTestStatus variable to indicate the current test status.
agnDriverSwMismatch
.1.3.6.1.4.1.164.6.1.0.20
There is mismatch between the SW driver and
the HW of the device uplink interface.
agnActualLowRate
.1.3.6.1.4.1.164.6.1.0.21
The main link is synchronized
at a rate lower than expected.
xModemFileTransferStatusTrap
.1.3.6.1.4.1.164.6.1.0.22
This trap is sent in the following cases:
- When an xModem File Transfer Session begins. In this case,
the trapVal.1 string sent will be: 'Start'.
- When an xModem File Transfer Session ends. In this case,
the trapVal.1 string sent will be one of the following,
according to the way the session ended :
- 'End: OK'
- 'End: Failed'
agnStationClkFailureTrap
.1.3.6.1.4.1.164.6.1.0.23
This trap is sent upon Station Clock failure.
successfulLogin
.1.3.6.1.4.1.164.6.1.0.24
This trap is sent when a user performed successful Login via
Terminal/Telnet/Web. This trap is used when the device is located
at End-User's premises while management is at Service Provider's
premises.
failedLogin
.1.3.6.1.4.1.164.6.1.0.25
This trap is sent when a user tried to Login via Terminal/Telnet/Web
and failed. This trap is used when the device is located
at End-User's premises while management is at Service Provider's
premises.
modlChangeTrap
.1.3.6.1.4.1.164.6.1.0.26
This trap is sent whenever a module is inserted or removed.
The trap should include the new module type (e.g. modlParamType).
licenseUpdateTrap
.1.3.6.1.4.1.164.6.1.0.27
This trap is sent whenever a license is successfully downloaded
or whenever a license's demo duration is expired.
agnClkSrcStateChangeTrap
.1.3.6.1.4.1.164.6.1.0.28
The trap is sent upon change in Recovery Clock State.
agnSelfTestResultChangeTrap
.1.3.6.1.4.1.164.6.1.0.29
The trap is sent upon each change in the result of a Self State operation.
prtStatusChangeTrap
.1.3.6.1.4.1.164.6.1.0.3
This trap is sent whenever the state of a port changed.
Attached, will be parameter/s that indicate the new port status.
The attached variables will be specified in the specifications
of the products supporting this trap.
agnCurrClkStateChangeTrap
.1.3.6.1.4.1.164.6.1.0.30
The trap is sent upon change in the state of the current (active) clock,
when it is a Recovery Clock.
agnClkSrcFrequencyAlarmTrap
.1.3.6.1.4.1.164.6.1.0.31
The trap is sent upon Recovered Clock Frequency alarm.
prtLoopDetectTrap
.1.3.6.1.4.1.164.6.1.0.32
This trap is sent upon Loop Detect (On/Off) on a certain port.
swdlStatusResult
.1.3.6.1.4.1.164.6.1.0.4
This notification is sent when Software Down Load is finished.
The attached object indicates the File Name.
systemDeviceTemperatureOra
.1.3.6.1.4.1.164.6.1.0.41
This trap indicates that Device Temprature is
above or below range.
systemAlternateConfigLoaded
.1.3.6.1.4.1.164.6.1.0.45
This trap indicates that one of the following files:
factory-default-config,
rollback-config,
user-default-config
or other file
was loaded as running-config.
Note that this notification should be sent only
if running-config is not startup-config
systemConfigurationSanity
.1.3.6.1.4.1.164.6.1.0.47
This notification MUST be sent if error has occurred while loading a configuration file.
It MUST only be sent once per file and only if the error policy is either 'ignore' or 'stop'
systemDyingGasp
.1.3.6.1.4.1.164.6.1.0.49
This Trap Indicates power Dying Gasp
intSwdlSlotFileMismatch
.1.3.6.1.4.1.164.6.1.0.5
This notification is sent when the card in the chosen slot doesn't match
the chosen file.
The attached object indicates the File Name.
systemDyingGaspRecovery
.1.3.6.1.4.1.164.6.1.0.50
This Trap Indicates power Dying Gasp Recovery
systemTraceMsgFatalError
.1.3.6.1.4.1.164.6.1.0.51
This Trap indicates that a critical error has occured in the device.
A corresponding message was added to the Trace Log Buffer.
systemTraceMsgException
.1.3.6.1.4.1.164.6.1.0.52
This Trap indicates that an error has occured in the device.
A corresponding message was added to the Trace Log Buffer.
systemDeviceStartup
.1.3.6.1.4.1.164.6.1.0.55
This Trap indicates that warm start or cold start of the device has occurred.
systemHardwareFailure
.1.3.6.1.4.1.164.6.1.0.58
This Trap indicates that a Hardware Failure has occured.
agnCounterChange
.1.3.6.1.4.1.164.6.1.0.6
This notification is sent when the value of a specific Counter is changed.
Agent can send as attached object the updated Counter.
For details about this Counter and attached object, see spec of the relevant
application.
systemStartupConfigUnconfirmed
.1.3.6.1.4.1.164.6.1.0.63
This Trap is sent during SW installation, if the user asked for a startup configuration
confirmation and the device didn't receive a confirmation from the user.
If the user didn't ask for confirmation - this trap will not be sent.
fanFailure
.1.3.6.1.4.1.164.6.1.0.64
This Trap indicates that there is a failure on the current fan.
prtClkSrcChangeTrap
.1.3.6.1.4.1.164.6.1.0.7
This trap is sent upon any port clock change.
systemSuccessfulLogin
.1.3.6.1.4.1.164.6.1.0.70
This Trap indicates that a successful login occurred.
systemFailedLogin
.1.3.6.1.4.1.164.6.1.0.71
This Trap indicates that an unsuccessful login occurred.
systemLogout
.1.3.6.1.4.1.164.6.1.0.72
This Trap indicates that logout was performed from the device.
systemTrapHardSyncStart
.1.3.6.1.4.1.164.6.1.0.77
This Trap indicates that hard trap synchronization process between the device
and NMS has started.
systemTrapHardSyncEnd
.1.3.6.1.4.1.164.6.1.0.78
This Trap indicates that hard trap synchronization process between the device
and NMS has ended.
moduleFailTrap
.1.3.6.1.4.1.164.6.1.0.8
This trap is sent upon a module failure.
systemUserReset
.1.3.6.1.4.1.164.6.1.0.82
This Trap Indicates that the user reset the device.
faultPropagation
.1.3.6.1.4.1.164.6.1.0.87
This trap indicates that an interface/port/card received fault propagation.
moduleInitFailTrap
.1.3.6.1.4.1.164.6.1.0.9
This trap is sent upon a module initialization failure.
systemResourceOverflow
.1.3.6.1.4.1.164.6.1.0.90
This notification is sent when a system resource overflows.
systemRemoteTerminalStarted
.1.3.6.1.4.1.164.6.1.0.91
This notification is sent when remote terminal to a virtual engine starts.
systemRemoteTerminalEnded
.1.3.6.1.4.1.164.6.1.0.92
This notification is sent when remote terminal to a virtual engine is terminated,
either by a user or by an inactivity timeout.
systemNtpAccuracyOutOfLimit
.1.3.6.1.4.1.164.6.1.0.93
This alarm notification is sent when NTP client accuracy becomes 'out of limit'.
systemSummerTimeStarted
.1.3.6.1.4.1.164.6.1.0.95
This event is sent when the agent enters summer time.
The event was obsoleted by systemTimeChanged.
systemSummerTimeEnded
.1.3.6.1.4.1.164.6.1.0.96
This event is sent when the agent exits summer time.
The event was obsoleted by systemTimeChanged.
systemFileOverflow
.1.3.6.1.4.1.164.6.1.0.97
This event is sent if a file reaches its maximum size.
The file name can be inferred from the
indices of the fileSystemValidIndication attached variable.
systemTimeChanged
.1.3.6.1.4.1.164.6.1.0.98
This event is sent when the system local time changes.
systemTimeSourceChanged
.1.3.6.1.4.1.164.6.1.0.99
This event is sent when the source providing time for the system changes.
hardSyncTrap
.1.3.6.1.4.1.164.6.2.61.2.0.1
This trap is sent whenever Hard Synchronization process starts or ends
(Hard Synchronization retrieves current status of Agent).