QTECH-MPLSOAM-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
43

qtechMplsOamIgrTable

table
.1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2 · 1 row entry · 12 columns
Open in standard view
Uses the qtech variant from /opt/observium/mibs/qtech.
Command help
Walk qtechMplsOamIgrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'QTECH-MPLSOAM-MIB' -M '/opt/observium/mibs/qtech:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'QTECH-MPLSOAM-MIB::qtechMplsOamIgrTable' 
This table specifies information for configuring
and monitoring LSP(or te tunnel).
qtechMplsOamIgrEntry row .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1
A row in this table represents information for configuring
and monitoring LSP(or te tunnel). It is indexed by
qtechMplsOamIgrIndex, which uniquely identifies a single LSP(or te tunnel).
Indexes
Column Syntax OID
qtechMplsOamIgrIndex
This is a unique index in the ingress table.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.1
qtechMplsOamIgrLspName
The name of an LSP(or te tunnel).
OctetStringr/w .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.2
qtechMplsOamIgrLspId
The ID of an LSP.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.3
qtechMplsOamIgrDetType
The OAM defect detection function is based on the periodic transmission
of CV or FFD packets from ingress to egress of an LSP. Each CV and FFD packet
carries a unique TTSI (Trail Termination Source Identifier), which …
Enumerationr/w
Enumerated Values:
1cv
2ffd
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.4
qtechMplsOamIgrDetFreq
For CV: the frequency is 1s.
For FFD: the frequency is one of
50ms,100ms,200ms,500ms.
0: 1s(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.5
qtechMplsOamIgrRevType
The BDI flow is injected on a return path (such as a return LSP) to inform the upstream LSR
(which is the source of the forward LSP) that there is a defect at the downstream LSP's LSR sink
point.BDI and loopback transac…
Enumerationr/w
Enumerated Values:
1private
2share
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.6
qtechMplsOamIgrRevLspName
The name of a return LSP.
OctetStringr/w .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.7
qtechMplsOamIgrEnable
The detection of OAM is enabled/disabled on the ingress of an LSP.
0: The OAM detection is disabled on the ingress;
1: The OAM detection is enabled on the ingress.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.8
qtechMplsOamIgrValid
0: stop detection of OAM;
1: start detection of OAM.
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.9
qtechMplsOamIgrAvaState
If the LSP Timer (T3) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after fir…
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.10
qtechMplsOamIgrDefectType
There are 6 types of defect in total, among which there are 4 MPLS layer user-plane
defects(i.e., dLOCV, dTTSI_Mismatch, dTTSI_Mismerge and dExcess), 1 Server layer defect,
1 peer maintenance entity defect:
0: no defect…
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.11
qtechMplsOamIgrRowStatus
It is used to create and
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.2.1.12

qtechMplsOamEgrTable

table
.1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3 · 1 row entry · 16 columns
Open in standard view
Uses the qtech variant from /opt/observium/mibs/qtech.
Command help
Walk qtechMplsOamEgrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'QTECH-MPLSOAM-MIB' -M '/opt/observium/mibs/qtech:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'QTECH-MPLSOAM-MIB::qtechMplsOamEgrTable' 
This table specifies information for configuring
and monitoring LSP(or te tunnel).
qtechMplsOamEgrEntry row .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1
A row in this table represents information for configuring
and monitoring LSP(or te tunnel). It is indexed by
qtechMplsOamEgrIndex, which uniquely identifies a single LSP(or te tunnel).
Indexes
Column Syntax OID
qtechMplsOamEgrIndex
This is a unique index in the egress table.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.1
qtechMplsOamEgrLspName
The name of static LSP at egress.
OctetStringr/w .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.2
qtechMplsOamEgrLsrId
The Ingress LSR ID of an LSP.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.3
qtechMplsOamEgrLspId
The ID of an LSP.
Integer32r/w
Constraints:
range: 1-65535
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.4
qtechMplsOamEgrDetType
0: adaptability;
1: CV;
2: FFD.
Enumerationr/w
Enumerated Values:
0adaptability
1cv
2ffd
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.5
qtechMplsOamEgrDetFreq
0: 1000ms(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms;
5: invalid.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
5invalid6
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.6
qtechMplsOamEgrRevType
The BDI flow is injected on a return path (such as a return LSP) to inform the upstream LSR
(which is the source of the forward LSP) that there is a defect at the downstream LSP's LSR sink
point.BDI and loopback transac…
Enumerationr/w
Enumerated Values:
0private
1share
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.7
qtechMplsOamEgrRevLspName
The name of a return LSP.
OctetStringr/w .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.8
qtechMplsOamEgrAutoEn
The adaptability is enabled/disabled.
0: disable;
1: enable.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.9
qtechMplsOamEgrAutoOvertime
The wait-time of adaptability.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.10
qtechMplsOamEgrBDIFreq
For CV: the frequency is 1s.
For FFD: the frequency is one of
50ms,100ms,200ms,500ms.
0: 1000ms(only for cv);
1: 50ms;
2: 100ms;
3: 200ms;
4: 500ms.
Enumerationr/w
Enumerated Values:
0cv1000ms
1ffd50ms2
2ffd100ms3
3ffd200ms4
4ffd500ms5
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.11
qtechMplsOamEgrEnable
The detection of OAM is enabled/disabled on the egress of an LSP.
0: The OAM detection is disabled on the egress;
1: The OAM detection is enabled on the egress.
Enumerationr/w
Enumerated Values:
0disable
1enable
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.12
qtechMplsOamEgrValid
1: stop detection of OAM;
2: start detection of OAM.
Enumeration
Enumerated Values:
1stop
2start
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.13
qtechMplsOamEgrAvaState
If the LSP Timer (T1) expires, then the LSP enters the
Unavailable state. The start point of the Unavailable state
is deemed to be at the entry into the LSP defect state.
An LSP re-enters the Available state after the…
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.14
qtechMplsOamEgrDefectType
There are 6 types of defect in total, among which there are 4 MPLS layer user-plane
defects(i.e., dLOCV, dTTSI_Mismatch, dTTSI_Mismerge and dExcess), 1 Server layer defect,
1 peer maintenance entity defect:
0: no defect…
Integer32
Constraints:
range: 0-7
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.15
qtechMplsOamEgrRowStatus
It is used to create and
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.1.3.1.16

qtechMplsPsTable

table
.1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1 · 1 row entry · 15 columns
Open in standard view
Uses the qtech variant from /opt/observium/mibs/qtech.
Command help
Walk qtechMplsPsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'QTECH-MPLSOAM-MIB' -M '/opt/observium/mibs/qtech:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'QTECH-MPLSOAM-MIB::qtechMplsPsTable' 
This table specifies information for configuring
and monitoring LSP protection group(or te tunnel protection group).
qtechMplsPsEntry row .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1
A row in this table represents information for configuring
and monitoring LSP protection group(or te tunnel protection group). It is indexed by
qtechMplsPsIndex, which uniquely identifies a single LSP protection group(o…
Indexes
Column Syntax OID
qtechMplsPsIndex
This is a unique index in the protection group table.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.1
qtechMplsPsGroupName
The protection group name.
OctetString .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.2
qtechMplsPsType
The MPLS PS architecture can be a 1+1 type, a 1:1 type, a shared mesh type,
or a packet 1+1 type.
1. In the 1+1 architecture type, a protection LSP is dedicated to each working
LSP with the working LSP bridged onto t…
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.3
qtechMplsPsWorkLspName
The name of work-lsp(or work-tunnel).
OctetString .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.4
qtechMplsPsWorkLspId
The ID of work-lsp(or work-tunnel).
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.5
qtechMplsPsProtectLspName
The name of protect-lsp.
OctetString .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.6
qtechMplsPsProtectLspId
The ID of protect-lsp(or protect-tunnel).
Integer32
Constraints:
range: 1-65535
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.7
qtechMplsPsRevertiveMode
The protection group revertive mode can be non-revertive and revertive
protection switching.
1. In revertive mode of operation, under conditions where working traffic
is being transmitted via the protection LSP and w…
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.8
qtechMplsPsWTR
Wait to restore is only applicable for the revertive mode and
applies to a working LSP. It prevents reversion back to select
the working LSP until the wait to restore timer has expired.
The wait to restore time may be c…
Integer32
Constraints:
range: 0-60
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.9
qtechMplsPsHoldOff
In general, if lower layer(e.g., SDH or optical) protection
mechanisms are being utilized in conjunction with MPLS layer
protection mechanisms, then the lower layers should have a
chance to restore working traffic befor…
Integer32
Constraints:
range: 0-100
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.10
qtechMplsPsSwitchCondition
The following switch initiation criteria exist:
1. an externally initiated command(clear, lockout of protection,
forced switch, manual switch);
2. an automatically initiated command(signal fail) associated with
a…
Integer32
Constraints:
range: 1-9
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.11
qtechMplsPsWorkLspState
The state of working lsp state lists below:
1: defect state;
2: non-defect state.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.12
qtechMplsPsProtLspState
The state of protection lsp state lists below:
1: defect state;
2: non-defect state.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.13
qtechMplsPsSwitchResult
Which lsp is user traffic being transmitted:
1: working-lsp;
2: protection-lsp.
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.14
qtechMplsPsRowStatus
It is used to create and
delete a row in this table.
1: active;
2: notInService;
3: notReady;
4: createAndGo;
5: createAndWait;
6: destroy.
SNMPv2-TCRowStatus
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.27514.1.1.10.2.93.1.3.1.1.15