QTECH-INTERFACE-MIB Table View

list of interface basic configuration objects.

qtechIfEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1

Entry contains interface basic configurations.

Indexes

qtechIfIndex

Column	Syntax	OID
qtechIfIndex	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.1
qtechIfPortType Port type of this port, list as above. port100MBASEFX indicates that port is port100MBASEFXL or port100MBASEFXS, and system doesn't distinguish. port1000MBASEFX indicates that port is port1000MBASEFLX or port1000MBASEFS…	Enumeration Enumerated Values: 1 unknown 2 port10M100MBASETX 3 port100MBASEFXL 4 port100MBASEFXS 5 port1000MBASESX 6 port1000MBASELX 7 port1000MBASETX 8 portGBIC 9 port100MBASEFX 10 port1000MBASEFX 11 portSFP 12 port10GBASESR 13 port10GBASELR 14 port10GBASEER 15 port10GBASELX4 16 port10GBASESW 17 port10GBASELW 18 port10GBASEEW 19 port10GBASE 20 port40GBASEKR 21 port40GBASECR 22 port40GBASELR 23 port40GBASESR 24 port40GBASE 25 port100GBASECR 26 port100GBASESR 27 port100GBASELR 28 port100GBASEER 29 port100GBASE 50 port155MCPOS 51 port622MCPOS 52 port2G5CPOS 53 port10GCPOS 54 port155MPOS 55 port622MPOS 56 port2G5POS 57 port10GPOS 58 port155MATM 59 port622MATM 60 port2G5ATM 61 port10GATM 62 portE1ELC	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.2
qtechIfFlowControlAdminStatus Flow control of a port management status. This attribute apply physical port and aggreate port	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 3 autonego 4 unknown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.3
qtechIfFlowControlOperStatus Oper status: after the negotiation between two ports connetted the flow contrl status. This attribute apply physical port and aggreate port	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.4
qtechIfAdminSpeed port speed settings. This attribute apply physical port and aggreate port	Enumerationr/w Enumerated Values: 1 speed10Mb 2 speed100Mb 3 speed1000Mb 4 autonego 5 speed10Gb 6 unknown 7 speed40Gb 8 speed100Gb	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.5
qtechIfAdminDuplex port duplex settings. This attribute apply physical port and aggreate port	Enumerationr/w Enumerated Values: 1 full 2 half 3 autonego 4 unknown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.6
qtechIfOperSpeed After two port have negotiated the speed status,and this object is the working speed status. while the port link status is down , then the speed status is unknown(4). This attribute apply physical port a…	Enumeration Enumerated Values: 1 speed10Mb 2 speed100Mb 3 speed1000Mb 4 unknown 5 speed10Gb 6 speed40Gb 7 speed100Gb	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.7
qtechIfOperDuplex After two port have negotiated the duplex status, and this object is the working duplex status. while the port link status is down , then the speed status is unknown(3). This attribute apply physical por…	Enumeration Enumerated Values: 1 full 2 half 3 unknown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.8
qtechIfManageStatus Management status of the interface.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.9
qtechIfIpBroadcast Broadcast address of the interface. if broadcast address not configured on interface, return 0.0.0.0	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.10
qtechIfLayer	Enumerationr/w Enumerated Values: 1 layer-2 2 layer-3	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.11
qtechIfMode This value is meaning for only physical port and aggreate port	Enumerationr/w Enumerated Values: 1 access 2 trunk 3 dot1q-tunnel 4 hybrid 5 other 6 uplink 7 host 8 promiscuous	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.12
qtechIfCounterClear Setting its to any value but 0, will clear counters of this interface. Setting its value to 0 will cause no action of the agent. and when query will always return 0.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.13
qtechIfEntryStatus Status of this entry, set this object to valid will create a interface, and set its value to invalid will delete the interface of this entry.	QTECH-TCConfigStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.14
qtechIfMediumType Port medium type of this port,fiber or copper.	Enumerationr/w Enumerated Values: 0 unknown 1 copper 2 fiber	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.15
qtechIfDownCounter The counters of linkdown times of the interface.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.16
qtechIfInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated b…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.17
qtechIfOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indi…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.18
qtechIfBcastInhibit The percentage of the broadcast storm restraint on the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.19
qtechIfNegotiation The negotiation status of the interface.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.20
qtechIfPhysAddress The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the for…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.21
qtechIfAdminSpeedRW port speed settings. This attribute apply physical port and aggreate port	Enumerationr/w Enumerated Values: 1 speed10Mb 2 speed100Mb 3 speed1000Mb 4 autonego 5 speed10Gb 6 unknown 7 speed40Gb 8 speed100Gb	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.22
qtechIfAdminDuplexRW port duplex settings. This attribute apply physical port and aggreate port	Enumerationr/w Enumerated Values: 1 full 2 half 3 autonego 4 unknown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.23
qtechIfModeRW This value is meaning for only physical port and aggreate port	Enumerationr/w Enumerated Values: 1 access 2 trunk 3 dot1q-tunnel 4 hybrid 5 other 6 uplink 7 host 8 promiscuous	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.24
qtechIfSpeed An estimate of the interface's current bandwidth in units of Mbits per second.	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.25
qtechifAdminStatus the interface keeps the admin state .	Enumerationr/w Enumerated Values: 1 adminup 2 admindown 3 admintest	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.26
qtechifOperStatus the interface keeps the oper state .	Enumeration Enumerated Values: 1 up 2 down 3 test 4 unknow 5 dormant	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.27
qtechIfInNUcastPkts The counter of receiving packets contain BROADCAST and PACKET_MULTICAST .	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.28
qtechIfOutNUcastPkts The counter of sending packets contain BROADCAST and PACKET_MULTICAST .	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.29
qtechIfUpDownTimes The counters of linkup and linkdown times of the interface.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.30
qtechifAdminStatusw The desired state of the interface. When a managed system initializes, all interfaces start with ifAdminStatus in the admindown(1) state. As a result of either explicit management action or per configuration informati…	Enumerationr/w Enumerated Values: 0 up 1 admindown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.31
qtechifOperStatusw The current operational state of the interface. If qtechApIfAdminStatus is admindown(2) then qtechApIfOperStatus should be admindown(2). If qtechApIfAdminStatus is changed to up(0) then qtechApIfOperStatus should cha…	Enumeration Enumerated Values: 0 up 1 down 2 admindown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.32
qtechifSpeedw An estimate of the interface's current bandwidth in units of Mbits per second.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.33
qtechifMacAddress The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the form…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.34
qtechifLastChange The length of the time that comes current state .	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.35
qtechIfInPkts The number of packets received on this interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as …	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.36
qtechIfDiscard The number of bound packets which were chosen to be discarded even though no errors. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.37
qtechIfBandwidthUsage Current bandwidth utilization of interface.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.38
qtechIfInBitsRate The average input packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.39
qtechIfInPktRate The average input packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.40
qtechIfOutBitsRate The average output packet-rate over a period of time(configuration by interface command 'load-interval') in bits per second on this interface.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.41
qtechIfOutPktRate The average output packet-rate over a period of time(configuration by interface command 'load-interval') in packets per second on this interface.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.1.1.42

A list of interface ip configuration entries.

qtechIfIpEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1

An entry containing configuration information applicable
to a Layer3 interface.

Indexes

qtechIfIpIfIndex qtechIfIpId qtechIfIp

Column	Syntax	OID
qtechIfIpIfIndex A unique value, for each Layer3 interface.	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1.1
qtechIfIpId Type of interface ip address.	Enumeration Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1.2
qtechIfIp Ip address of the interface qtechIfIndex refer to.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1.3
qtechIfIpMask Ip mask of the interface ip address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1.4
qtechIfIpEntryStatus entry status of this entry. and the means in this enviraments can reffer to the text-convention definition of the RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.27514.1.1.10.2.10.1.2.1.5

list of interface status. Status information include some error state and
result of examining to the interface,etc.

qtechIfStatusEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.3.1

Entry contains interface status information.

Indexes

qtechIfStatusIndex

Column	Syntax	OID
qtechIfStatusIndex	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.3.1.1
qtechIfStatusLoopBackExamine Setting its to any value but 0, will Checking whether this port or aggreate can receive and send packets normally, It indicates that port or aggreate is normal if opertion is success. Setting its value to 0 will ca…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.3.1.2
qtechIfErrorStatus Port's error status information	Enumeration Enumerated Values: 1 no-error 2 err-disable-bpduguard 3 err-disable-ptsecurity	.1.3.6.1.4.1.27514.1.1.10.2.10.1.3.1.3
qtechIfLineDetect When reading this object, system detects the quality of line connecting the port. Detect whether the line is broken or short circuit or not. The meaning of the obtained value: Return value=N*10000000+M N…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.3.1.4

Table of entrance to choose port type.

qtechPortTypeChooseEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.5.1

Entrance to choose port type.

Indexes

qtechPortTypeChooseIndex

Column	Syntax	OID
qtechPortTypeChooseIndex The logic port number.	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.5.1.1
qtechPortTypeChooseType The chosen port type. This object is used to choose one of the multiple physical ports of different types, when the same logical port is correspondent with them. Apply this attribute to the physical port only.	Enumeration Enumerated Values: 1 fiber 2 copper	.1.3.6.1.4.1.27514.1.1.10.2.10.1.5.1.2

Access table of MTU on interface.

qtechIfMTUEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.6.1

Interfac MTU access.

Indexes

qtechIfMTUIndex

Column	Syntax	OID
qtechIfMTUIndex Interface number	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.6.1.1
qtechIfMTU Interface MTU.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.6.1.2

Access table of Available Bandwidth on interface.

qtechIfAvailableBWEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.7.1

Interfac available bandwidth access.

Indexes

qtechIfAvailableBWIfIndex

Column	Syntax	OID
qtechIfAvailableBWIfIndex Interface number	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.7.1.1
qtechIfAvailableBWIfBW Interface available bandwidth(bit).	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.7.1.2

Access table of Available Bandwidth on interface.

qtechIfSVICreatEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.8.1

Interfac available bandwidth access.

Indexes

qtechIfSVICreatVlanNum

Column	Syntax	OID
qtechIfSVICreatVlanNum Interface Vlan number	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.27514.1.1.10.2.10.1.8.1.1
qtechIfHandleSVI 0 creat,1 delete.	Enumerationr/w Enumerated Values: 0 create 1 delete	.1.3.6.1.4.1.27514.1.1.10.2.10.1.8.1.2

Access table of Available Bandwidth on interface.

qtechIfLinkUPTimesEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.10.1

Interfac available bandwidth access.

Indexes

qtechInterfaceIndex

Column	Syntax	OID
qtechInterfaceIndex Interface Index	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.10.1.1
qtechIfLinkUPTimes Vlaues Of Linkup Times.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.10.1.2

Access table of Encapsulation dot1q VLAN on interface.

qtechIfEncapsulationEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.11.1

Interfac encapsulation dot1q VLAN access.

Indexes

qtechIfEncapsulationIndex

Column	Syntax	OID
qtechIfEncapsulationIndex A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system …	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.11.1.1
qtechIfEncapsulationVlan The value indicate the VID of the dot1q vlan encapsulation. The value 0 means de-encapsulation.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.27514.1.1.10.2.10.1.11.1.2

Access table of ap interface number.

qtechApIfNumberEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.12.1

Interfac number of ap.

Indexes

qtechApPhyAddress

Column	Syntax	OID
qtechApPhyAddress The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial …	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.27514.1.1.10.2.10.1.12.1.1
qtechApIfNumber Vlaues Of interface number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.12.1.2
qtechApIfPhyIntNum Vlaues Of physical interface number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.12.1.3

A list of qtechAp interface entries.  The number of entries
is given by the value of qtechApIfNumber.

qtechApIfEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1

An entry containing management information qtechApplicable
to a particular interface.

Indexes

qtechApPhysAddress qtechApIfIndex

Column	Syntax	OID
qtechApPhysAddress The ap's address at its protocol sub-layer. The ap's media-specific MIB must define the bit and byte ordering and the format of the value of this object. For interfaces which do not have such an address (e.g., a serial …	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.1
qtechApIfIndex A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initiali…	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.2
qtechApIfDescr A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.3
qtechApIfType The type of interface. Additional values for ifType are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention.	IANAifType-MIBIANAifType Type Values: 1 other 2 regular1822 3 hdh1822 4 ddnX25 5 rfc877x25 6 ethernetCsmacd 7 iso88023Csmacd 8 iso88024TokenBus 9 iso88025TokenRing 10 iso88026Man 11 starLan 12 proteon10Mbit 13 proteon80Mbit 14 hyperchannel 15 fddi 16 lapb 17 sdlc 18 ds1 19 e1 20 basicISDN 21 primaryISDN 22 propPointToPointSerial 23 ppp 24 softwareLoopback 25 eon 26 ethernet3Mbit 27 nsip 28 slip 29 ultra 30 ds3 31 sip 32 frameRelay 33 rs232 34 para 35 arcnet 36 arcnetPlus 37 atm 38 miox25 39 sonet 40 x25ple 41 iso88022llc 42 localTalk 43 smdsDxi 44 frameRelayService 45 v35 46 hssi 47 hippi 48 modem 49 aal5 50 sonetPath 51 sonetVT 52 smdsIcip 53 propVirtual 54 propMultiplexor 55 ieee80212 56 fibreChannel 57 hippiInterface 58 frameRelayInterconnect 59 aflane8023 60 aflane8025 61 cctEmul 62 fastEther 63 isdn 64 v11 65 v36 66 g703at64k 67 g703at2mb 68 qllc 69 fastEtherFX 70 channel 71 ieee80211 72 ibm370parChan 73 escon 74 dlsw 75 isdns 76 isdnu 77 lapd 78 ipSwitch 79 rsrb 80 atmLogical 81 ds0 82 ds0Bundle 83 bsc 84 async 85 cnr 86 iso88025Dtr 87 eplrs 88 arap 89 propCnls 90 hostPad 91 termPad 92 frameRelayMPI 93 x213 94 adsl 95 radsl 96 sdsl 97 vdsl 98 iso88025CRFPInt 99 myrinet 100 voiceEM 101 voiceFXO 102 voiceFXS 103 voiceEncap 104 voiceOverIp 105 atmDxi 106 atmFuni 107 atmIma 108 pppMultilinkBundle 109 ipOverCdlc 110 ipOverClaw 111 stackToStack 112 virtualIpAddress 113 mpc 114 ipOverAtm 115 iso88025Fiber 116 tdlc 117 gigabitEthernet 118 hdlc 119 lapf 120 v37 121 x25mlp 122 x25huntGroup 123 transpHdlc 124 interleave 125 fast 126 ip 127 docsCableMaclayer 128 docsCableDownstream 129 docsCableUpstream 130 a12MppSwitch 131 tunnel 132 coffee 133 ces 134 atmSubInterface 135 l2vlan 136 l3ipvlan 137 l3ipxvlan 138 digitalPowerline 139 mediaMailOverIp 140 dtm 141 dcn 142 ipForward 143 msdsl 144 ieee1394 145 if-gsn 146 dvbRccMacLayer 147 dvbRccDownstream 148 dvbRccUpstream 149 atmVirtual 150 mplsTunnel 151 srp 152 voiceOverAtm 153 voiceOverFrameRelay 154 idsl 155 compositeLink 156 ss7SigLink 157 propWirelessP2P 158 frForward 159 rfc1483 160 usb 161 ieee8023adLag 162 bgppolicyaccounting 163 frf16MfrBundle 164 h323Gatekeeper 165 h323Proxy 166 mpls 167 mfSigLink 168 hdsl2 169 shdsl 170 ds1FDL 171 pos 172 dvbAsiIn 173 dvbAsiOut 174 plc 175 nfas 176 tr008 177 gr303RDT 178 gr303IDT 179 isup 180 propDocsWirelessMaclayer 181 propDocsWirelessDownstream 182 propDocsWirelessUpstream 183 hiperlan2 184 propBWAp2Mp 185 sonetOverheadChannel 186 digitalWrapperOverheadChannel 187 aal2 188 radioMAC 189 atmRadio 190 imt 191 mvl 192 reachDSL 193 frDlciEndPt 194 atmVciEndPt 195 opticalChannel 196 opticalTransport 197 propAtm 198 voiceOverCable 199 infiniband 200 teLink 201 q2931 202 virtualTg 203 sipTg 204 sipSig 205 docsCableUpstreamChannel 206 econet 207 pon155 208 pon622 209 bridge 210 linegroup 211 voiceEMFGD 212 voiceFGDEANA 213 voiceDID 214 mpegTransport 215 sixToFour 216 gtp 217 pdnEtherLoop1 218 pdnEtherLoop2 219 opticalChannelGroup 220 homepna 221 gfp 222 ciscoISLvlan 223 actelisMetaLOOP 224 fcipLink 225 rpr 226 qam 227 lmp 228 cblVectaStar 229 docsCableMCmtsDownstream 230 adsl2 231 macSecControlledIF 232 macSecUncontrolledIF 233 aviciOpticalEther 234 atmbond 235 voiceFGDOS 236 mocaVersion1 237 ieee80216WMAN 238 adsl2plus 239 dvbRcsMacLayer 240 dvbTdm 241 dvbRcsTdma 242 x86Laps 243 wwanPP 244 wwanPP2 245 voiceEBS 246 ifPwType 247 ilan 248 pip 249 aluELP 250 gpon 251 vdsl2 252 capwapDot11Profile 253 capwapDot11Bss 254 capwapWtpVirtualRadio 255 bits 256 docsCableUpstreamRfPort 257 cableDownstreamRfPort 258 vmwareVirtualNic 259 ieee802154 260 otnOdu 261 otnOtu 262 ifVfiType 263 g9981 264 g9982 265 g9983 266 aluEpon 267 aluEponOnu 268 aluEponPhysicalUni 269 aluEponLogicalLink 270 aluGponOnu 271 aluGponPhysicalUni 272 vmwareNicTeam 277 docsOfdmDownstream 278 docsOfdmaUpstream 279 gfast 280 sdci 281 xboxWireless 282 fastdsl 283 docsCableScte55d1FwdOob 284 docsCableScte55d1RetOob 285 docsCableScte55d2DsOob 286 docsCableScte55d2UsOob 287 docsCableNdf 288 docsCableNdr 289 ptm 290 ghn 291 otnOtsi 292 otnOtuc 293 otnOduc 294 otnOtsig 295 microwaveCarrierTermination 296 microwaveRadioLinkTerminal 297 ieee8021axDrni 298 ax25 299 ieee19061nanocom 300 cpri 301 omni 302 roe 303 p2pOverLan	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.4
qtechApIfMtu The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.5
qtechApIfSpeed An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal…	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.6
qtechApIfPhysAddress The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the form…	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.7
qtechApIfAdminStatus The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with ifAdminStatus in the admindown(2) state. As a…	Enumerationr/w Enumerated Values: 1 up 2 admindown 3 testing	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.8
qtechApIfOperStatus The current operational state of the interface. If qtechApIfAdminStatus is admindown(2) then qtechApIfOperStatus should be admindown(3). If qtechApIfAdminStatus is changed to up(1) then qtechApIfOperStatus should cha…	Enumeration Enumerated Values: 1 up 2 down 3 admindown 4 unknown 5 dormant 6 notPresent 7 lowerLayerDown	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.9
qtechApIfLastChange The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object c…	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.10
qtechApIfInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.11
qtechApIfInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.12
qtechApIfInNUcastPktsdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.13
qtechApIfInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.14
qtechApIfInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of in…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.15
qtechApIfInUnknownProtos For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protoc…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.16
qtechApIfOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at othe…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.17
qtechApIfOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.18
qtechApIfOutNUcastPktsdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.19
qtechApIfOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.20
qtechApIfOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could no…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.21
qtechApIfOutQLendeprecated The length of the output packet queue (in packets).	RFC1155-SMIGauge Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.22
qtechApIfLinkUPTimes Vlaues Of Linkup Times.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.23
qtechApIfInDataOctets The data octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicat…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.24
qtechApIfOutDataOctets The data octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as …	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.25
qtechApIfMgmtUploadOctets The upload octets received on the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.26
qtechApIfMgmtDownloadOctets The download octets transmitted out of the mgmt interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.27
qtechApIfSpeedw An estimate of the interface's current bandwidth in units of Mbits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.28
qtechApIfMtuw The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.29
qtechApIfPhysAddressw The interface's address at its protocol sub-layer. For example, for an 802.x interface, this object normally contains a MAC address. The interface's media-specific MIB must define the bit and byte ordering and the form…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.30
qtechApIfInUcastPktsw The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.31
qtechApIfInNUcastPktswdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.32
qtechApIfOutUcastPktsw The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.33
qtechApIfOutNUcastPktswdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.34
qtechApIfLinkUPTimesw The counters of linkup and linkdown times of the interface.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.35
qtechApIfInPkts The total number of packets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other time…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.13.1.36

A list of interface entries.  The number of entries is
given by the value of ifNumber.

qtechIfLinkEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1

An entry containing management information applicable to a
particular interface.

Indexes

qtechIfLinkIndex

Column	Syntax	OID
qtechIfLinkIndex A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initiali…	QTECH-TCIfIndex Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.1
qtechIfUplinkInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.2
qtechIfUplinkInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.3
qtechIfUplinkInNUcastPktsdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.4
qtechIfUplinkInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.5
qtechIfUplinkInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of i…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.6
qtechIfUplinkOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at othe…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.7
qtechIfUplinkOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.8
qtechIfUplinkOutNUcastPktsdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.9
qtechIfUplinkOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.10
qtechIfUplinkOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.11
qtechIfDownlinkInOctets The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.12
qtechIfDownlinkInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.13
qtechIfDownlinkInNUcastPktsdeprecated The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.14
qtechIfDownlinkInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.15
qtechIfDownlinkInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of i…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.16
qtechIfDownlinkOutOctets The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at othe…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.17
qtechIfDownlinkOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.18
qtechIfDownlinkOutNUcastPktsdeprecated The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.19
qtechIfDownlinkOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.20
qtechIfDownlinkOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.21
qtechIfUplinkInBcastPkts The number of upbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counte…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.22
qtechIfUplinkOutBcastPkts The number of upbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this count…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.23
qtechIfDownlinkInBcastPkts The number of downbound and inbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this coun…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.24
qtechIfDownlinkOutBcastPkts The number of downbound and outbound packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this cou…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.14.1.25

A table of link traffic statistics, including interface rate and bandwidth utilization.

qtechIfLinkTrafficEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1

The link traffic statistics entry.

Indexes

qtechIfLinkTrafficIndex

Column	Syntax	OID
qtechIfLinkTrafficIndex The link traffic interface index.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1.1
qtechIfLinkAvgRate An estimate of the interface's average bandwidth in units of bits per second.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1.2
qtechIfLinkPeakRate An estimate of the interface's current peak bandwidth in units of bits per second.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1.3
qtechIfLinkAvgBWUtilization An estimate of the interface's average bandwidth Utilization.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1.4
qtechIfLinkPeakBWUtilization An estimate of the interface's current peak bandwidth Utilization.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.1.1.1.5

The results of these operations are stored in the qtechLinkQosResultsTable

qtechLinkQosCtlEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1

Defines an entry in the qtechLinkQosCtlTable. The first index
element, qtechLinkQosCtlOwnerIndex, is of type SnmpAdminString,
a textual convention that allows for use of the SNMPv3
View-Based Access Control Model (RFC …

Indexes

qtechLinkQosCtlOwnerIndex qtechLinkQosCtlTestName

Column	Syntax	OID
qtechLinkQosCtlOwnerIndex To facilitate the provisioning of access control by a security administrator using the View-Based Access Control Model (RFC 2575, VACM) for tables in which multiple users may need to create or modify entries independent…	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.1
qtechLinkQosCtlTestName The name of the ping-based test. This is locally unique, within the scope of a qtechLinkQosCtlOwnerIndex.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.2
qtechLinkQosCtlTargetAddressType Specifies the type of host address to be used at a remote host for performing a ping-based operation.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.3
qtechLinkQosCtlTargetAddress Specifies the host address to be used at a remote host for performing a ping-based operation. The host address type is determined by the value of the corresponding qtechLinkQosCtlTargetAddressType.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.4
qtechLinkQosCtlAdminStatus Reflects the desired state that a qtechLinkQosCtlEntry should be in: enabled(1) - Attempt to activate the test as defined by this qtechLinkQosCtlEntry. disabled(2) - Deactivate the test as define…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.5
qtechLinkQosCtlRowStatus This variable is used to create, modify, and/or delete a row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.1.1.6

The results of these operations are stored in the qtechLinkQosResultsTable.

qtechLinkQosResultsEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1

Defines an entry in the qtechLinkQosResultsTable. The
qtechLinkQosResultsTable has the same indexing as the
qtechLinkQosCtlTable so that a qtechLinkQosResultsEntry
corresponds to the qtechLinkQosCtlEntry that caused it…

Indexes

qtechLinkQosCtlOwnerIndex qtechLinkQosCtlTestName

Column	Syntax	OID
qtechLinkQosResultsOperStatus Reflects the operational state of a qtechLinkQosCtlEntry: enabled(1) - Test is active. disabled(2) - Test has stopped. completed(3) - Test is completed.	Enumeration Enumerated Values: 1 enabled 2 disabled 3 completed	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.1
qtechLinkQosResultsIpTargetAddressType This object indicates the type of address stored in the corresponding qtechLinkQosResultsIpTargetAddress object.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.2
qtechLinkQosResultsIpTargetAddress This object reports the IP address associated with a qtechLinkQosCtlTargetAddress value when the destination address is specified as a DNS name. The value of this object should be a zero-length octet string when a DN…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.3
qtechLinkQosResultsMaxRtt The maximum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received.	millisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.4
qtechLinkQosResultsMinRtt The minimum packet round-trip-time (RTT) that received. A value of 0 for this object implies that no RTT has been received.	millisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.5
qtechLinkQosResultsAverageRtt The current average packet round-trip-time (RTT).	millisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.6
qtechLinkQosResultsDelayJitter This object contains the sum of the squares for all ping responses received. Its purpose is to enable standard deviation calculation. The estimate value of the delay jitter.	millisecondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.7
qtechLinkQosResultsPktsLossRate The packets loss rate of the link.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.8
qtechLinkQosResultsNetworkAF The network availability factor.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.2.2.1.9

A table of device traffic statistics.

qtechIfDeviceTrafficEntry row .1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1

Device traffic statistics entry

Indexes

qtechIfDeviceTrafficIndex

Column	Syntax	OID
qtechIfDeviceTrafficIndex The device traffic interface index.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.1
qtechIfFC The FC type. 2--BASE_X_10 4--BASE_X_100 6--BASE_X_1000 8--BASE_X_10000 9--BASE_ERROR	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.2
qtechIfFCTransRate The transmission rate of the FC.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.3
qtechIfFCTransPktsNum The transmission packets number of the FC.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.4
qtechIfFCDiscardRate The discard rate of the FC.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.5
qtechIfFCDiscardPktsNum The discard packets number of the FC.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.6
qtechIfFCPktsLossRate The packets loss rate of the FC.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.7
qtechIfFCBandwidthRate The bandwidth rate of the FC.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.8
qtechIfFCBandwidthPercentage The bandwidth percentage of the FC.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.9
qtechIfDeviceFCGathers Gathers of the device FC.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.10
qtechIfFullMeshFCGathers Gathers of the whole network FC.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.11
qtechIfClassBasedGathers Class-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.12
qtechIfNodeBasedGathers Node-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.13
qtechIfNodeClassBasedGathers Node&class-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.14
qtechIfNodeFCBasedGathers Node&FC-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.15
qtechIfNodeDeviceFCBasedGathers Node&device&FC-based Gathers.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.27514.1.1.10.2.10.1.15.3.1.1.16