PW-STD-R-MIB Table View

This table specifies information for configuring and 
status monitoring which are common to all service types 
and PSN types.

pwEntry row .1.3.6.1.4.1.164.20.10.1.2.1

A row in this table represents a pseudo-wire (PW) virtual
connection across a packet network. It is indexed by
pwIndex, which uniquely identifies a singular
connection.
A row can be created by an operator command …

Indexes

pwIndex

Column	Syntax	OID
pwIndex A unique index for the conceptual row identifying a PW within this table.	PW-TC-STD-R-MIBPwIndexType Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.1
pwType This value indicates the emulated service to be carried over this PW.	IANA-PWE3-R-MIBIANAPwTypeTCr/w Type Values: 0 other 1 frameRelayDlciMartiniMode 2 atmAal5SduVcc 3 atmTransparent 4 ethernetTagged 5 ethernet 6 hdlc 7 ppp 8 cem 9 atmCellNto1Vcc 10 atmCellNto1Vpc 11 ipLayer2Transport 12 atmCell1to1Vcc 13 atmCell1to1Vpc 14 atmAal5PduVcc 15 frameRelayPortMode 16 cep 17 e1Satop 18 t1Satop 19 e3Satop 20 t3Satop 21 basicCesPsn 22 basicTdmIp 23 tdmCasCesPsn 24 tdmCasTdmIp 25 frDlci 32767 wildcard	.1.3.6.1.4.1.164.20.10.1.2.1.2
pwOwner This object is set by the operator to indicate the protocol responsible for establishing this PW. 'manual' is used in all cases where no maintenance protocol (PW signaling) is used to set-up the PW, i.e. require c…	Enumerationr/w Enumerated Values: 1 manual 2 pwIdFecSignaling 3 genFecSignaling 4 l2tpControlProtocol 5 other	.1.3.6.1.4.1.164.20.10.1.2.1.3
pwPsnType This object is set by the operator to indicate the PSN type. Based on this object, the relevant PSN table's entry is created in the PSN specific MIB modules.	IANA-PWE3-R-MIBIANAPwPsnTypeTCr/w Type Values: 1 mpls 2 l2tp 3 udpOverIp 4 mplsOverIp 5 mplsOverGre 6 other	.1.3.6.1.4.1.164.20.10.1.2.1.4
pwSetUpPriority This object defines the relative priority of the PW during set-up in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated with equal priority. PW that have not yet succee…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.164.20.10.1.2.1.5
pwHoldingPriority This object defines the relative holding priority of the PW in a lowest-to-highest fashion, where 0 is the highest priority. PWs with the same priority are treated equally. This value is significant if there are co…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.164.20.10.1.2.1.6
pwPeerAddrType Denotes the address type of the peer node. It should be set to 'unknown' if PE/PW maintenance protocol is not used and the address is unknown.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.164.20.10.1.2.1.8
pwPeerAddr This object contains the value of the peer node address of the PW/PE maintenance protocol entity. This object SHOULD contain a value of all zeroes if not applicable (pwPeerAddrType is 'unknown').	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.9
pwAttachedPwIndex If the PW is attached to another PW instead of a local native service, this item indicates the pwIndex of the attached PW. Otherwise, this object MUST be set to zero. Attachement to another PW will have no PW speci…	PW-TC-STD-R-MIBPwIndexOrZeroTyper/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.10
pwIfIndex This object indicates the ifIndex of the PW if the PW is represented in the ifTable. Otherwise, it MUST be set to zero.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.164.20.10.1.2.1.11
pwID Used in the outgoing PW ID field within the 'Virtual Circuit FEC Element'. Applicable if pwOwner equal 'pwIdFecSignaling' or 'l2tpControlProtocol', otherwise it SHOULD be set to zero.	PW-TC-STD-R-MIBPwIDTyper/w	.1.3.6.1.4.1.164.20.10.1.2.1.12
pwLocalGroupID Used in the Group ID field sent to the peer PWES within the maintenance protocol used for PW setup. It SHOULD be set to zero if maintenance protcol is not used.	PW-TC-STD-R-MIBPwGroupIDr/w	.1.3.6.1.4.1.164.20.10.1.2.1.13
pwGroupAttachmentID This object is an octet string representing the attachment group identifier (AGI) that this PW belongs too, which typically identifies the VPN ID. Applicable if pwOwner equal 'genFecSignaling'.	PW-TC-STD-R-MIBPwAttachmentIdentifierTyper/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.14
pwLocalAttachmentID This object is an octet string representing the local forwarder attachment individual identifier (AII) to be used by this PW. It is used as the SAII for outgoing signaling messages and the TAII in the incoming mes…	PW-TC-STD-R-MIBPwAttachmentIdentifierTyper/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.15
pwPeerAttachmentID This object is an octet string representing the peer forwarder attachment individual identifier (AII) to be used by this PW. It is used as the TAII for outgoing signaling messages and the SAII in the incoming mess…	PW-TC-STD-R-MIBPwAttachmentIdentifierTyper/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.16
pwCwPreference Defines if the control word will be sent with each packet by the local node. Some PW types mandate the use of a control word, and in such cases the value configured for this object has no effect on the existence of …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.10.1.2.1.17
pwLocalIfMtu If not equal to zero, the optional IfMtu object in the signaling protocol will be sent with this value, which represents the locally-supported MTU size over the interface (or the virtual interface) associated with…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.164.20.10.1.2.1.18
pwLocalIfString A PW MAY be associated to an interface (or a virtual interface) in the ifTable of the node as part of the service configuration. This object defines if the maintenance protocol will send the interface's name (ifAl…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.10.1.2.1.19
pwLocalCapabAdvert If maintenance protcol is used, it indicates the capabilities the local node will advertize to the peer. The operator MAY selectively assign partial set of capabilities. In case of manual configuration of the PW, …	IANA-PWE3-R-MIBIANAPwCapabilitiesr/w Type Values: 0 pwStatusIndication 1 pwVCCV	.1.3.6.1.4.1.164.20.10.1.2.1.20
pwRemoteGroupID This object is obtained from the Group ID field as received via the maintenance protocol used for PW setup. Value zero will be reported if not used. Value of 0xFFFF shall be used if the object is yet to be defined …	PW-TC-STD-R-MIBPwGroupID	.1.3.6.1.4.1.164.20.10.1.2.1.21
pwCwStatus If signaling is used for PW establishment, this object indicates the status of the control word negotiation, and in both; signaling or manual configuration it indicates if CW is to be present for this PW.	PW-TC-STD-R-MIBPwCwStatusTC Type Values: 1 waitingForNextMsg 2 sentWrongBitErrorCode 3 rxWithdrawWithWrongBitErrorCode 4 illegalReceivedBit 5 cwPresent 6 cwNotPresent 7 notYetKnown	.1.3.6.1.4.1.164.20.10.1.2.1.22
pwRemoteIfMtu The remote interface MTU as (optionally) received from the remote node via the maintenance protocol. The object SHOULD report zero if MTU is not available.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.23
pwRemoteIfString Indicates the interface description string as received by the maintenance protocol. It MUST be a NULL string if maintenance protocol is not used or the value is not known yet.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.164.20.10.1.2.1.24
pwRemoteCapabilities Indicates the capabilities as recieved from the peer.	IANA-PWE3-R-MIBIANAPwCapabilities Type Values: 0 pwStatusIndication 1 pwVCCV	.1.3.6.1.4.1.164.20.10.1.2.1.25
pwFragmentCfgSize If set to a value other than zero, indicates that fragmentation is desired for this PW. This object MAY be changed only if the PW is not active.	bytesPW-TC-STD-R-MIBPwFragSizer/w	.1.3.6.1.4.1.164.20.10.1.2.1.26
pwRmtFragCapability The status of the fragmentation based on the local configuration and the peer capabilities as recieved from the peer when control protocol is used.	PW-TC-STD-R-MIBPwFragStatus Type Values: 0 noFrag 1 cfgFragGreaterThanPsnMtu 2 cfgFragButRemoteIncapable 3 remoteFragCapable 4 fragEnabled	.1.3.6.1.4.1.164.20.10.1.2.1.27
pwFcsRetentionCfg The local configuration of FCS retention for this PW. FCS retention can be configured for PW types HDLC, PPP and Ethernet only. If the implementation does not support FCS retention, error MUST be reported in pwFcsR…	Enumerationr/w Enumerated Values: 1 fcsRetentionDisable 2 fcsRetentionEnable	.1.3.6.1.4.1.164.20.10.1.2.1.28
pwFcsRetentionStatus The status of the FCS retention negotiation process based on local configuration and the remote advertisement. remoteIndicationUnknown - set if a FEC has not been received from the remote. …	Bits Enumerated Values: 0 remoteIndicationUnknown 1 remoteRequestFcsRetention 2 fcsRetentionEnabled 3 fcsRetentionDisabled 4 localFcsRetentionCfgErr 5 fcsRetentionFcsSizeMismatch	.1.3.6.1.4.1.164.20.10.1.2.1.29
pwOutboundLabel The PW label used in the outbound direction (i.e. toward the PSN). It might be set manually if pwOwner is 'manual', otherwise setting done automatically. For MPLS, MPLS over IP or MPLS over GRE PSN, it represents t…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.30
pwInboundLabel The PW label used in the inbound direction (i.e. packets received from the PSN). It may be set manually if pwOwner is 'manual',otherwise setting done automatically. For MPLS, MPLS over IP or MPLS over GRE PSN, it r…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.31
pwName The canonical name assigned to the PW. This object MAY be changed at any time.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.32
pwDescr A textual string containing information about the PW. If there is no description this object contains a zero length string. This object MAY be changed at any time.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.2.1.33
pwCreateTime The value of sysUpTime at the time this PW was created.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.164.20.10.1.2.1.34
pwUpTime Specifies the time since last change of pwOperStatus to Up(1).	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.35
pwLastChange The value of sysUpTime at the time the PW entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object conta…	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.164.20.10.1.2.1.36
pwAdminStatus The desired operational status of this PW. This object MAY be set at any time.	Enumerationr/w Enumerated Values: 1 up 2 down 3 testing	.1.3.6.1.4.1.164.20.10.1.2.1.37
pwOperStatus This object indicates the operational status of the PW, it does not reflect the status of the CE bound interface. It is set to down only if pwNotForwarding, psnFacingPwRxFault, or psnFacingPwTxFault indications ar…	PW-TC-STD-R-MIBPwOperStatusTC Type Values: 1 up 2 down 3 testing 4 dormant 5 notPresent 6 lowerLayerDown	.1.3.6.1.4.1.164.20.10.1.2.1.38
pwLocalStatus Indicates the status of the PW in the local node. The various indications in this object SHOULD be available independent of the ability of the local node to advertise them or the remote node to accept these status …	PW-TC-STD-R-MIBPwStatus Type Values: 0 pwNotForwarding 1 servicePwRxFault 2 servicePwTxFault 3 psnPwRxFault 4 psnPwTxFault	.1.3.6.1.4.1.164.20.10.1.2.1.39
pwRemoteStatusCapable Indicates the remote node capability to advertise the PW status notification. notAppicable SHOULD be reported for manually set PW, or if the local node is not capable of accepting the status notification object. …	Enumeration Enumerated Values: 1 notApplicable 2 notYetKnown 3 remoteCapable 4 remoteNotCapable	.1.3.6.1.4.1.164.20.10.1.2.1.40
pwRemoteStatus Indicates the status of the PW as was advertised by the remote. If the remote is not capable of advertising the status object, or the local node is not able to accept the status object through signaling, then the …	PW-TC-STD-R-MIBPwStatus Type Values: 0 pwNotForwarding 1 servicePwRxFault 2 servicePwTxFault 3 psnPwRxFault 4 psnPwTxFault	.1.3.6.1.4.1.164.20.10.1.2.1.41
pwTimeElapsed The number of seconds, including partial seconds, that have elapsed since the beginning of the current interval measurement period.	HC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.4.1.164.20.10.1.2.1.42
pwValidIntervals The number of previous 15-minute intervals for which data was collected.	HC-PerfHist-TC-MIBHCPerfValidIntervals Type Constraints: range: 0..96	.1.3.6.1.4.1.164.20.10.1.2.1.43
pwRowStatus For creating, modifying, and deleting this row. This object MAY be changed at any time.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.164.20.10.1.2.1.44
pwStorageType This variable indicates the storage type for this object.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.164.20.10.1.2.1.45
pwOamEnable This variable indicates if OAM is enabled for this PW. It MAY be changed at any time.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.10.1.2.1.46

This table provides per-PW performance information for  
the current interval.

pwPerfCurrentEntry row .1.3.6.1.4.1.164.20.10.1.3.1

An entry in this table is created by the agent for
every PW.

Indexes

pwIndex

Column	Syntax	OID
pwPerfCurrentInHCPackets High capacity counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInPackets, if pwPerfCurrentInHCPackets is supported accord…	HC-PerfHist-TC-MIBHCPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.1
pwPerfCurrentInHCBytes High capacity counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentInBytes, if pwPerfCurrentInHCBytes is supported according t…	HC-PerfHist-TC-MIBHCPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.2
pwPerfCurrentOutHCPackets High capacity counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutPackets, if pwPerfCurrentOutHCPackets is supported accor…	HC-PerfHist-TC-MIBHCPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.3
pwPerfCurrentOutHCBytes High capacity counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. This is the 64 bit version of pwPerfCurrentOutBytes, if pwPerfCurrentOutHCBytes is supported according t…	HC-PerfHist-TC-MIBHCPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.4
pwPerfCurrentInPackets The counter for number of packets received by the PW (from the PSN) in the current 15-minute interval. This is the 32 bit version of pwPerfCurrentInHCPackets, if pwPerfCurrentInHCPackets is supported according to …	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.5
pwPerfCurrentInBytes The counter for number of bytes received by the PW (from the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentInHCBytes, if pwPerfCurrentInHCBytes is supp…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.6
pwPerfCurrentOutPackets The counter for number of packets forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCPackets, if pwPerfCurrentOutHCPackets i…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.7
pwPerfCurrentOutBytes The counter for number of bytes forwarded by the PW (to the PSN) in the current 15-minute interval. It MUST be equal to the least significant 32 bits of pwPerfCurrentOutHCBytes, if pwPerfCurrentOutHCBytes is suppo…	PerfHist-TC-MIBPerfCurrentCount	.1.3.6.1.4.1.164.20.10.1.3.1.8

This table provides per-PW performance information for  
each interval.

pwPerfIntervalEntry row .1.3.6.1.4.1.164.20.10.1.4.1

An entry in this table is created by the agent for every
PW.

Indexes

pwIndex pwPerfIntervalNumber

Column	Syntax	OID
pwPerfIntervalNumber A number N, between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified b…	Integer32 Constraints: range: 1-96	.1.3.6.1.4.1.164.20.10.1.4.1.1
pwPerfIntervalValidData This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.10.1.4.1.2
pwPerfIntervalTimeElapsed The duration of this interval in seconds.	HC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.4.1.164.20.10.1.4.1.3
pwPerfIntervalInHCPackets High capacity counter for number of packets received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInPackets, if pwPerfIntervalInHCPackets is supported according to the …	HC-PerfHist-TC-MIBHCPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.4
pwPerfIntervalInHCBytes High capacity counter for number of bytes received by the PW (from the PSN) during the interval. This is the 64 bit version of pwPerfIntervalInBytes, if pwPerfIntervalInHCBytes is supported according to the rule…	HC-PerfHist-TC-MIBHCPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.5
pwPerfIntervalOutHCPackets High capacity counter for number of packets forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutPackets, if pwPerfIntervalOutHCPackets is supported according to th…	HC-PerfHist-TC-MIBHCPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.6
pwPerfIntervalOutHCBytes High capacity counter for number of bytes forwarded by the PW (to the PSN) during the interval. This is the 64 bit version of pwPerfIntervalOutBytes, if pwPerfIntervalOutHCBytes is supported according to the rule…	HC-PerfHist-TC-MIBHCPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.7
pwPerfIntervalInPackets This value represents the number of packets received by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalInHCPackets if pwPerfIntervalInHCPackets is supported accor…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.8
pwPerfIntervalInBytes This value represents the number of bytes received by this PW during the interval. It MUST be equal to the least significant 32 bits of if pwPerfIntervalInHCBytes is supported according to the rules spelled out i…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.9
pwPerfIntervalOutPackets This value represents the number of packets sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCPackets if pwPerfIntervalOutHCPackets is supported accordi…	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.10
pwPerfIntervalOutBytes This value represents the number of bytes sent by this PW during the interval. It MUST be equal to the least significant 32 bits of pwPerfIntervalOutHCBytes if pwPerfIntervalOutHCBytes is supported according to …	PerfHist-TC-MIBPerfIntervalCount	.1.3.6.1.4.1.164.20.10.1.4.1.11

This table provides per-PW Performance information for
the current day measurment and the previous days interval.

pwPerf1DayIntervalEntry row .1.3.6.1.4.1.164.20.10.1.5.1

An entry in this table is created by the agent for every
PW.

Indexes

pwIndex pwPerf1DayIntervalNumber

Column	Syntax	OID
pwPerf1DayIntervalNumber History Data Interval number. Interval 1 is the current day measurement period, interval 2 is the most recent previous day, and interval 30 is 31 days ago. Intervals 3..31 are optional.	Unsigned32 Constraints: range: 1-31	.1.3.6.1.4.1.164.20.10.1.5.1.1
pwPerf1DayIntervalValidData This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.164.20.10.1.5.1.2
pwPerf1DayIntervalTimeElapsed The number of seconds in the 1-day interval over which the performance monitoring information is actually counted. This value will be the same as the interval duration except in a situation where performance monitoring …	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.4.1.164.20.10.1.5.1.3
pwPerf1DayIntervalInHCPackets High capacity counter for the total number of packets received by the PW (from the PSN).	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.164.20.10.1.5.1.4
pwPerf1DayIntervalInHCBytes High capacity counter for the total number of bytes received by the PW (from the PSN).	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.164.20.10.1.5.1.5
pwPerf1DayIntervalOutHCPackets High capacity counter for the total number of packets forwarded by the PW (to the PSN).	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.164.20.10.1.5.1.6
pwPerf1DayIntervalOutHCBytes High capacity counter for the total number of bytes forwarded by the PW (to the PSN).	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.164.20.10.1.5.1.7

This table enables the reverse mapping the unique PWid 
parameters [peer IP, PW type and PW ID] and the  
pwIndex. The table is not applicable for PW created  
manually or by using the generalized FEC.

pwIndexMappingEntry row .1.3.6.1.4.1.164.20.10.1.7.1

An entry in this table MUST be created by the agent for
every PW created by the pwTable for which pwOwner
equals pwIdFecSignaling.

Implementors need to be aware that if the value of
the pwIndexMappingPe…

Indexes

pwIndexMappingPwType pwIndexMappingPwID pwIndexMappingPeerAddrType pwIndexMappingPeerAddr

Column	Syntax	OID
pwIndexMappingPwType The PW type (indicates the service) of this PW.	IANA-PWE3-R-MIBIANAPwTypeTC Type Values: 0 other 1 frameRelayDlciMartiniMode 2 atmAal5SduVcc 3 atmTransparent 4 ethernetTagged 5 ethernet 6 hdlc 7 ppp 8 cem 9 atmCellNto1Vcc 10 atmCellNto1Vpc 11 ipLayer2Transport 12 atmCell1to1Vcc 13 atmCell1to1Vpc 14 atmAal5PduVcc 15 frameRelayPortMode 16 cep 17 e1Satop 18 t1Satop 19 e3Satop 20 t3Satop 21 basicCesPsn 22 basicTdmIp 23 tdmCasCesPsn 24 tdmCasTdmIp 25 frDlci 32767 wildcard	.1.3.6.1.4.1.164.20.10.1.7.1.1
pwIndexMappingPwID The PW ID of this PW. Zero if the PW is configured manually.	PW-TC-STD-R-MIBPwIDType	.1.3.6.1.4.1.164.20.10.1.7.1.2
pwIndexMappingPeerAddrType IP address type of the peer node.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.164.20.10.1.7.1.3
pwIndexMappingPeerAddr IP address type of the peer node.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.7.1.4
pwIndexMappingPwIndex The value that represents the PW in the pwTable.	PW-TC-STD-R-MIBPwIndexType Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.164.20.10.1.7.1.5

This table provides reverse mapping of the existing PW  
based on PW type and PW ID ordering. This table is  
typically useful for EMS ordered query of existing PWs.

pwPeerMappingEntry row .1.3.6.1.4.1.164.20.10.1.8.1

An entry in this table is created by the agent for every
PW entry in pwTable.

Implementors need to be aware that if the value of
the pwPeerMappingPeerAddr (an OID) or
pwPeerMappingPwID (an OID) (or both …

Indexes

pwPeerMappingPeerAddrType pwPeerMappingPeerAddr pwPeerMappingPwType pwPeerMappingPwID

Column	Syntax	OID
pwPeerMappingPeerAddrType IP address type of the peer node.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.164.20.10.1.8.1.1
pwPeerMappingPeerAddr IP address of the peer node.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.164.20.10.1.8.1.2
pwPeerMappingPwType The PW type (indicates the emulated service) of this PW.	IANA-PWE3-R-MIBIANAPwTypeTC Type Values: 0 other 1 frameRelayDlciMartiniMode 2 atmAal5SduVcc 3 atmTransparent 4 ethernetTagged 5 ethernet 6 hdlc 7 ppp 8 cem 9 atmCellNto1Vcc 10 atmCellNto1Vpc 11 ipLayer2Transport 12 atmCell1to1Vcc 13 atmCell1to1Vpc 14 atmAal5PduVcc 15 frameRelayPortMode 16 cep 17 e1Satop 18 t1Satop 19 e3Satop 20 t3Satop 21 basicCesPsn 22 basicTdmIp 23 tdmCasCesPsn 24 tdmCasTdmIp 25 frDlci 32767 wildcard	.1.3.6.1.4.1.164.20.10.1.8.1.3
pwPeerMappingPwID The PW ID of this PW. Zero if the PW is configured manually.	PW-TC-STD-R-MIBPwIDType	.1.3.6.1.4.1.164.20.10.1.8.1.4
pwPeerMappingPwIndex The value that represents the PW in the pwTable.	PW-TC-STD-R-MIBPwIndexType Type Constraints: range: 1..4294967295	.1.3.6.1.4.1.164.20.10.1.8.1.5