 almRLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.1 | Trap of Alarm: Loss of signal. |
almRsCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.10 | Trap of Alarm: Regenerator section performance over threshold. |
almLTI
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.100 | Trap of Alarm: Loss of timing input. |
almSynBad
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.101 | Trap of Alarm: Synchronous Source Degrade. |
almTAlos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.107 | Trap of Alarm: E1/T1 interface loss of analog signal. |
almSyncCLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.111 | Trap of Alarm: Loss of synchronization source level. |
almFanFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.115 | Trap of Alarm: Fan failure. |
almE1Los
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.117 | Trap of Alarm: 2M Line Loss Of Signal. |
almUpE1Ais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.118 | Trap of Alarm: 2M up signal alarm indication. |
almBdStatus
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.119 | Trap of Alarm: Board not in position alarm. |
almB1Exc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12 | Trap of Alarm: Regenerator section (B1) excessive errors. |
almPs
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.120 | Trap of Alarm:Protection switch indication |
almWrgBdType
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.121 | Trap of Alarm: Wrong board type. |
almEthOamRmtLoop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12291 | Trap of Alarm: The ETHOAM_RMT_LOOP is an alarm indicating the remote loopback of point-to-point Ethernet OAM. This alarm only occurs to the port with the point-to-point OAM protocol enabled. If the port is able to respond to loopback, it enters the loopback response state and reports the loopback response alarm after it receives the remote loopback enabling command sent by the opposite OAM port. The loopback initiator reports the loopback initiating alarm. If the port receives the loopback disabling command, it exits the loopback response state and ends the loopback response alarm. The loopback initiator end also ends the loopback initiating alarm. |
almEthOamRmtSd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12292 | Trap of Alarm: The EthOamRmtSd is an alarm indicating the remote SD of point-to-point Ethernet OAM. When the port with the OAM protocol enabled receives the link event message from the opposite end which indicates that the remote Ethernet performance degraded, this alarm occurs. |
almEthOamRmtCritFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12293 | Trap of Alarm: The EthOamRmtCritFault is an alarm indicating that a critical fault occurs to the remote end of point-to-point Ethernet OAM. When the port with the OAM protocol enabled receives the OAM message that contains critical fault information from the opposite end, this alarm occurs. |
almEthOamDiscoverFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12294 | Trap of Alarm: EthOamDiscoverFail is an alarm indicating the point-to-point Ethernet OAM discovery failure. When the OAM protocol is enabled at the port of a board and the negotiation with the opposite equipment fails, this alarm occurs. |
almDownT1Ais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12295 | Trap of Alarm: 1.5M down signal alarm indication. |
almExEthOamCCLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12298 | Trap of Alarm: Continuity Check Message Loss |
almExEthOamMpidCnflct
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12299 | Trap of Alarm: Maintenance Identify Conflict |
almLptRfi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12300 | Trap of Alarm: The LPT_RFI is a remote failure indication alarm of link state pass through. This alarm occurs when the link state pass through (LPT) detects the failure of the remote port or the LPT service network. |
almFlowOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12301 | Trap of Alarm: Port inflow over the limit |
almRelayAlarmCritical
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12305 | Trap of Alarm: Critical relay alarm. |
almRelayAlarmMajor
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12306 | Trap of Alarm: Major relay alarm. |
almRelayAlarmMinor
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12307 | Trap of Alarm: Minor relay alarm. |
almRelayAlarmIgnore
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12308 | Trap of Alarm: Relay alarm warning. |
almPowerFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.125 | Trap of Alarm: Power failure |
almRemoteFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12544 | Trap of Alarm: Remote defect alarm of ethernet port. |
almLocalFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12545 | Trap of Alarm: Local defect alarm of ethernet port. |
almHardErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12580 | Trap of Alarm: Hardware error. |
almNoElabel
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12581 | Trap of Alarm:No e-label |
almSysLogCommFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12586 | Trap of Alarm: the NE and the SYSLOG server have an abnormal connection or session in the TCP mode. |
almMwRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12587 | Trap of Alarm: Microwave remote defect indication. |
almMwFecUncor
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12588 | Trap of Alarm: Forward Error Correction code uncorrectable. |
almIfInPwrAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12589 | Trap of Alarm: Abnormal IF power received by ODU. |
almXcpIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12590 | Trap of Alarm:XCS protection switching indication |
almWrgDevType
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12593 | Trap of Alarm: Wrong device type. |
almCFCardOffLine
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12598 | Trap of Alarm: CF Card offline. |
almCFCardFailed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12599 | Trap of Alarm: CF Card Failed. |
almCFCardWRDisabled
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12600 | Trap of Alarm:The CFCARD_W_R_DISABLED is an alarm indicating that reading and writing the CF card are disabled. |
almPrbsLss
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12643 | Trap of Alarm:Loss of PRBS(Pseudo-Random Binary Sequence) signal |
almEthOamSelfLoop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12767 | Trap of Alarm: Ethernet OAM(802.3ah) self loop alarm |
almEthOamVcgSelfLoop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12768 | Trap of Alarm: Ethernet OAM(802.3ah)self loop alarm |
almLagPortFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12769 | Trap of Alarm: Port aggregation failure |
almLagVcPortFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12770 | Trap of Alarm: VCTRUNK aggregation failure |
almPatchDeactTimeout
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12775 | Trap of Alarm: Patch Deactivation Timeout |
almPatchActTimeout
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12776 | Trap of Alarm: Patch Activation Timeout |
almCFCardFull
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12777 | Trap of Alarm:CF card capacity fully used |
almEthNoFlow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12786 | Trap of Alarm: No traffic at Ethernet port. |
almPortModeMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12788 | Trap of Alarm: Working mode mismatch at remote FE port. |
almPatchPkgErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12790 | Trap of Alarm: Patch package file error. |
almSyncDisable
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12792 | Trap of Alarm: State of auto-synchronization disabled. |
almEthLinkDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12793 | Trap of Alarm: Failure of network interface connection. |
almMacFcsExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12794 | Trap of Alarm: An alarm indicating that the number of FCS errors received over the Ethernet interface crosses the threshold. |
almMacFcsSd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12795 | Trap of Alarm: An alarm indicating that FCS errors received over the Ethernet interface crosses the lower(degraded) threshold. |
almCesLospktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12796 | Trap of Alarm: Loss Packets Excess. |
almCesMisorderpktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12797 | Trap of Alarm: Misorder Dropped Packets Excess. |
almCesStraypktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12798 | Trap of Alarm: Stray Dropped Packets Excess. |
almCesMalpktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12799 | Trap of Alarm: Malformed Packets Excess alarm. |
almCesJtrudrExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12800 | Trap of Alarm: Jitter buffer underrun alarm. |
almCesJtrovrExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12801 | Trap of Alarm: Jitter buffer overrun alarm. |
almCesRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12802 | Trap of Alarm: Jitter buffer overrun alarm. |
almMpDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12803 | ML-PPP group failure. |
almMpDelay
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12804 | Delay alarm. |
almPppLcpFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12805 | LCP negotiation failure. |
almPppNcpFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12806 | NCP negotiation alarm. |
almFdbSizeAlmElan
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12807 | Trap of Alarm: Mac fdb of elan used up. |
almVpLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12808 | Trap of Alarm: Lost of Continuity Check. |
almVcLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12809 | Trap of Alarm: Lost of Continuity Check. |
almMplsTunnelLocv
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12814 | Trap of Alarm: Loss of Connectivity Verification defect. |
almMplsTunnelExcess
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12815 | Trap of Alarm: Receiving excess rate of CV. |
almMplsTunnelMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12816 | Trap of Alarm: Trail Termination Source Identifier Mismatch defect. |
almMplsTunnelMismerge
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12817 | Trap of Alarm: Trail Termination Source Identifier Mismerge defect. |
almMplsTunnelUnknown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12818 | Trap of Alarm: Unknown defect in the MPLS network. |
almMplsTunnelBdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12819 | Trap of Alarm: Backward Defect Indicator. |
almMplsTunnelFdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12820 | Trap of Alarm: Forward Defect Indicator. |
almMplsTunnelSD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12821 | Trap of Alarm: Signal Degrade. |
almMplsTunnelSF
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12822 | Trap of Alarm: Signal Fail. |
almEthCfmMisMerge
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12823 | Trap of Alarm: Trap of Alarm: Misconnection alarm |
almEthCfmUnexPeri
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12824 | Trap of Alarm: Errored frame alarm |
almEthCfmLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12825 | Trap of Alarm: Loss of continuity |
almEthCfmRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12826 | Trap of Alarm: Remote Defect Indication |
almEthEfmDf
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12827 | Trap of Alarm: Discovery failure |
almEthEfmRemFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12828 | Trap of Alarm: Remote failure |
almEthEfmEvent
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12829 | Trap of Alarm: Remote link event |
almEthEfmLoopBack
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12830 | Trap of Alarm: Loopback alarm |
almEthApsTypeMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12831 | Trap of Alarm: Mismatch of APS Protection Type. |
almEthApsPathMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12832 | Trap of Alarm: Working/Protection mismatch. |
almEthApsSwitchFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12833 | Trap of Alarm: Protection switching incomplete. |
almEthApsLost
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12834 | Trap of Alarm: APS Frame Lost. |
almLagMemberDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12836 | Trap of Alarm: LAG member unavailable |
almLagDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12837 | Trap of Alarm: LAG unavailable |
almImaGroupLeDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12838 | Trap of Alarm: IMA group Local Edge fail. |
almImaGroupReDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12839 | Trap of Alarm: IMA group Remote Edge fail. |
almPwDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12852 | Trap of Alarm: pw drop packets crosses the threshold. |
almPwDroppktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12853 | Trap of Alarm: pw drop packets crosses the threshold. |
almPwExcTraffic
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12854 | Trap of Alarm: Loss of OSC interface input optical power. |
almLcsLimited
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12860 | Trap of Alarm: The capacity exceeds the limitation specified by the license. |
almLicenseLost
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12861 | Trap of Alarm: Loss of license file. |
almXPICLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12862 | Trap of Alarm: Loss of XPIC signal. |
almIfCableOpen
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12863 | Trap of Alarm: Open circuit of IF cable. |
almIfModeUnSupported
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12864 | Trap of Alarm: The IF mode is not supported. |
almNp1SWIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12865 | Trap of Alarm: N+1 protection switching indication. |
almNp1SWFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12866 | Trap of Alarm: N+1 automatic protection switching failure indication. |
almNp1ManualStop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12867 | Trap of Alarm: N+1 APS protocol manually stopped. |
almModTypeMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12868 | Trap of Alarm: The module type that is set by the user does not match the actual module type. |
almRpsIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12869 | Trap of Alarm: Microwave protection switching alarm. |
almMwBerEXC
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12870 | Trap of Alarm: Microwave link excessive errors. |
almMwBerSD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12871 | Trap of Alarm: Microwave link signal degraded. |
almPatchChgsccNotMatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12872 | Trap of Alarm: Patch inconsistency after the SCC board is replaced. |
almStormCurQuenumOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12884 | Alarm storm. Certain alarms on the SCC board may be lost when the alarm queue is full. This alarm indicates that the alarm module is in the alarm storm state. |
almAcrLockFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12910 | Trap of Alarm: 1588ACR Lock Failure. |
almElpsCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12918 | Trap of Alarm:The Ethernet linear protection switching (ELPS) configuration at both ends mismatches. |
almEthPwrSupplyFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12923 | Circuit failure result in no power output or turnoff the power to protect the circuit. |
almImae1Delay
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12925 | Trap of Alarm: The transmission delay of the IMA link exceeds the threshold. |
almLanLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12926 | Trap of Alarm: LAN Loss of carrier signal. |
almEthAutoLinkDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12928 | Trap of Alarm: Automatic link down of Ethernet port. |
almTimeNoTraceMode
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12963 | Trap of Alarm: Time having no source to follow. |
almTimeLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12964 | Trap of Alarm: Time source loss of signal. |
almExtTimeLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12972 | Trap of Alarm: The external clock source is lost. |
almProtConnErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12974 | Trap of Alarm:Misconnected to IFH2 |
almRadioFadingMarginInsuff
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12989 | Trap of Alarm: The fading margin is insufficient. |
almGspTnnlDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12994 | Trap of Alarm: Tunnel Down. |
almGspIsisNbAuthErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12996 | Trap of Alarm: ISIS Neighbor Authentication err. |
almGspRsvpNbDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12997 | Trap of Alarm: RSVP Neighbor Down. |
almGspRsvpNbAuthErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.12998 | Trap of Alarm: RSVP Neighbor Authentication err. |
almUpT1Ais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.130 | Trap of Alarm: 1.5M up signal alarm indication. |
almE1Ais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13006 | Trap of Alarm:AIS of E1 frame |
almE1Lof
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13007 | Trap of Alarm:Loss of E1 frame |
almArpMacMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13008 | Trap of Alarm: The mac of static arp is mismatched. |
almPassWordNeedChange
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13047 | Trap of Alarm: The default user's default password must be changed to reduce risks. |
almErpsInProtection
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13048 | Trap of Alarm: Indicates that a node on the EPRS ring is faulty. |
almComExtEccFull
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13049 | Trap of Alarm: Number of TCP connections between NEs running the automatically extended ECC protocol exceeding the system limit . |
almAMDownShift
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13050 | Trap of Alarm: AM modulation downshift. |
almMultiRplOwner
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13064 | Trap of Alarm: More than one RPL_OWNER alarm |
almRadioRslBeyondTh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13069 | Trap of Alarm: The ODU threshold exceeds the threshold. |
almAtmpwLospktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13075 | Trap of Alarm:Number of lost packets over the threshold in a certain period |
almAtmpwMisorderpktExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13076 | Trap of Alarm:Number of disorder packets over the threshold in a certain period |
almAtmpwUnknowncellExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13077 | Trap of Alarm: Number of unknown cells over the threshold in a certain period. |
almCespwRemoteLospkt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13078 | Trap of Alarm:Remote loss packet of CES PW |
almCespwOppositeRai
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13080 | Trap of Alarm: The opposite station has a remote alarm indication. |
almCespwOppositeAcfault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13081 | Trap of Alarm: The opposite station has an attachment circuit fault. |
almMplsTunnelOamFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13087 | Trap of Alarm: Tunnel OAM protocol negotiation failure. |
almCpuBusy
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13090 | Trap of Alarm: CPU BUSY. |
almMplsPwLocv
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13091 | Trap of Alarm: Pw loss of connectivity verification. |
almMplsPwExcess
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13092 | Trap of Alarm: Excessive pw terminal source identifications (TTSIs) received. |
almMplsPwMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13093 | Trap of Alarm: Mismatched pw terminal source identifications (TTSIs). |
almMplsPwMismerge
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13094 | Trap of Alarm: Incorrect merging of PW terminal source identifications (TTSIs). |
almMplsPwUnknown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13095 | Trap of Alarm: Unknown pw defect in the MPLS network. |
almMplsPwBdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13096 | Trap of Alarm: Pw backward defect indication. |
almMplsPwSD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13097 | Trap of Alarm: Pw signal degrade. |
almMplsPwSF
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13098 | Trap of Alarm: Pw signal fail. |
almPwapsTypeMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13099 | Trap of Alarm: Mismatch of APS Protection Types. |
almPwapsPathMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13100 | Trap of Alarm: Mismatch of APS working/protection paths. |
almPwapsSwitchFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13101 | Trap of Alarm: Protection switching failure. |
almPwapsLost
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13102 | Trap of Alarm: APS frame lost. |
almMcapsApsidMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13103 | Trap of Alarm:MCAPS APSID MisMatch |
almMcapsDnipwMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13104 | Trap of Alarm:MCAPS DNI PW MisMatch |
almImaTxclkMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13105 | Trap of Alarm: The transmit clock modes of an IMA group are inconsistent at both ends. |
almPwNoTraffic
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13107 | When no traffic is received, this alarm is reported. |
almLagBwMM
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13108 | Trap of Alarm: Bandwidth inconsistency in the LAG group. |
almDcnSizeOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13110 | Trap of Alarm: DCN Size Over. |
almDcnLinkOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13111 | Trap of Alarm: The number of DCN OSPF neighbors excesses the suggested threshold. |
almMemOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13112 | Trap of Alarm:MEM_OVER |
almMcspPathLocv
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13113 | Trap of Alarm:Loss of Connectivity Verification defect |
almMclagCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13114 | Trap of Alarm:Configuration of MC-LAG Mismatch |
almLptCfgCloseport
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13115 | Trap of Alarm: LPT closed access port. |
almLcsMisMatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13122 | Trap of Alarm: This alarm indicates that, in the protection group, the license capacity of the boards differs from each other. |
almFanAging
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13123 | Trap of Alarm: Fan aging. |
almNtpSyncFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13125 | Trap of Alarm: NTP Synchronization Failure. |
almMplsPwOamfail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13135 | Indicates a PW OAM protocol negotiation failure. |
almLcsFileNotExist
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13144 | Trap of Alarm: No license file. |
almLcsExpired
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13145 | Trap of Alarm: License expiredLicense. |
almLcsDaysOfGrace
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13146 | Trap of Alarm: The license has expired and is within the keepalive period of 60 days. |
almCesK1K2M
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13147 | Trap of Alarm: K1K2 Mismatch. |
almCesK2M
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13148 | Trap of Alarm: K2 Mismatch. |
almCesApsIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13149 | Trap of Alarm: APS state indication. |
almCesApsFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13150 | Trap of Alarm:APS protection switching failure |
almCesLpsUniBiM
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13152 | Trap of Alarm:alarm of mismatch in unidirectional operation and bidirectional operation in msp_linear |
almOdcDoorOpen
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13154 | Trap of Alarm: The cabinet door is open. |
almOdcSurgeProtectionFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13155 | Trap of Alarm: A lightning-protection alarm is reported. |
almOdcSmokeOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13156 | Trap of Alarm: Smoke is detected in the cabinet. |
almOdcWaterAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13157 | Trap of Alarm: Water enters the cabinet. |
almOdcLoadPwrdown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13158 | Trap of Alarm: Power-down occurs in the load. |
almOdcBatteryPwrDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13159 | Trap of Alarm: The battery is powered down. |
almOdcBatteryCurrentAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13160 | Trap of Alarm: The storage battery is discharged unevenly. |
almOdcFanFailed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13161 | Trap of Alarm: The fan is not installed. |
almOdcTecAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13162 | Trap of Alarm: The TEC does not exist. |
almOdcPowerFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13163 | Trap of Alarm: The power module of the board works incorrectly. |
almOdcHumiAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13164 | Trap of Alarm: A humidity alarm is generated. |
almOdcMdlAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13165 | Trap of Alarm: An alarm is generated on the power module. |
almOdcTempAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13166 | Trap of Alarm: A temperature alarm is generated. |
almSecRadiusFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13169 | Trap of Alarm: Excessive failures in radius authentication. |
almCesApsManualStop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13173 | Trap of Alarm: CES APS protocol manually stopped. |
almMplsPwFdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13182 | Trap of Alarm: FDI packets are received, indicating a fault in the server PW. |
almMwCfgMisMatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13183 | Trap of Alarm: Radio link configuration failure. |
almLicenseDiff
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13187 | Trap of Alarm: Inconsistent license capacity. |
almPtpTimeStampAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13188 | Trap of Alarm: PTP time stamp anomaly. |
almPtpSourceSwitch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13194 | Trap of Alarm: PTP time source switching alarm. |
almClkLockFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13195 | Trap of Alarm: Clock lock failure alarm. |
almTimeLockFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13196 | Trap of Alarm: Time lock failure alarm. |
almCesAcrLockAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13277 | Trap of Alarm: Lockout anomaly of CES ACR service clock. |
almEthCfmFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13281 | Trap of Alarm:ETH OAM 1AG protocol negotiating failed. |
almLdpPeerDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13283 | Trap of Alarm:The connection status of the LDP peer is not Operational. |
almBdtempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13284 | Trap of Alarm: Board temperature sensor failure. |
almEnvtempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13285 | Trap of Alarm: Ambient temperature sensor failure. |
almOut1tempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13286 | Trap of Alarm: Air outlet temperature sensor failure. |
almIntempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13287 | Trap of Alarm: Air inlet temperature sensor failure. |
almOut2tempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13288 | Trap of Alarm: Failure of the temperature sensor of the external cycling air inlet. |
almBat1tempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13289 | Trap of Alarm: Failure of the temperature sensor in battery group 1. |
almEnvhumSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13290 | Trap of Alarm: Ambient humidity sensor failure. |
almEnvtemp1SensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13291 | Trap of Alarm: Failure of the sensor for ambient temperature 1. |
almEnvtemp2SensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13292 | Trap of Alarm: Failure of the sensor for ambient temperature 2. |
almBat2tempSensorFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13293 | Trap of Alarm: Failure of the temperature sensor in battery group 2. |
almMwE1Lost
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13294 | Trap of Alarm: This alarm is reported when the modulation scheme is downshifted or the E1 bandwidth is decreased. |
almMwContWave
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13295 | Trap of Alarm: This alarm is reported when continuous waves are enabled on the IF board (IF1, IFU2, IFX2, ISU2, or ISX2). |
almIsisLspOverload
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13303 | Trap of Alarm: The ISIS LSP at this node is overloaded. Therefore, information that this LSP carries is incomplete. |
almL3vpnTunnelDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13307 | Trap of Alarm: L3VPN-Bound Tunnel Interruption. |
almPortQueueDropOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13374 | Trap of Alarm: Packets dropped in port queue congestion exceeding the threshold. |
almPortcarRedpktOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13375 | Trap of Alarm:Packets marked red in port exceeding the threshold |
almTunnelApsDegraded
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13377 | Trap of Alarm: The unused tunnel in a protect group is faulty. |
almPgPrtDegraded
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13382 | Trap of Alarm: Downgrade of Protection Group. |
almPgLinkFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13383 | Trap of Alarm: Protection Group Link Failure. |
almMwAmTest
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13384 | Trap of Alarm: AM Test Status. |
almMplsTunnelLck
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13388 | Trap of Alarm: The server layer of MPLS Tunnel locked signal. |
almMplsPwLck
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13389 | Trap of Alarm: This alarm occurs when pw receives a LCK frame. |
almMplsPwAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13390 | MPLS Pw Alarm Indication Signal. |
almMplsTunnelLock
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13391 | Trap of Alarm: This alarm occurs when administrator set lock at a specific tunnel. |
almMplsPwLock
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13392 | Trap of Alarm: This alarm occurs when administrator set lock at a specific PW. |
almMplsTunnelUnexpmeg
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13393 | MPLS Tunnel Unexpected MEG. |
almMplsTunnelUnexpmep
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13394 | MPLS Tunnel Unexpected MEP. |
almMplsTunnelUnexpper
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13395 | MPLS Tunnel Unexpected Period. |
almMplsTunnelRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13396 | MPLS Pw Remote Defect Indication. |
almMplsTunnelAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13397 | MPLS Tunnel Alarm Indication Signal. |
almMplsPwUnexpmeg
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13398 | Trap of Alarm: MPLS PW Unexpected MEG. |
almMplsPwUnexpmep
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13399 | Trap of Alarm: MPLS Pw Unexpected MEPID. |
almMplsPwUnexpper
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13400 | Trap of Alarm: MPLS Pw Unexpected Period. |
almMPlsPwRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13401 | Trap of Alarm: MPLS Pw Remote Defect Indication. |
almMplsPwCsf
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13402 | Trap of Alarm: Received a CSF OAM packet, indicates the far-end client detect a faulty. |
almMplsSectLocv
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13403 | Trap of Alarm: Section loss of continuity. |
almMplsSectOamFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13404 | Trap of Alarm: the source and sink nodes of a Section fail to negotiate on the OAM protocol. |
almMplsSectUnexpmeg
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13405 | Trap of Alarm: Section Unexpected MEG. |
almMplsSectUnexpmep
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13406 | Trap of Alarm: Section Unexpected MEP. |
almMplsSectUnexpper
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13407 | Trap of Alarm: Section Unexpected Period. |
almMplsSectRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13408 | Trap of Alarm: Section Remote Defect Indication. |
almMplsSectSd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13409 | Trap of Alarm: the Section signal is degraded. |
almMplsSectSf
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13410 | Trap of Alarm: the Section signal is severely degraded. |
almMplsSectLock
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13411 | Trap of Alarm: Administratinve locking of section layer. |
almSrvShutDownLd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13416 | Trap of Alarm: Indicats the service shutdown for detecting loop on the network. With the service restarted, the alarm disappears. |
almPortExcTraffic
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13417 | Trap of Alarm: Indicats the traffic utilization at the Ethernet port over the threshold. When the received or transmitted traffic exceeds the expected traffic, this alarm occurs. |
almDropratioOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13418 | Trap of Alarm: Indicats the ratio of the packet discarded on some performance object over the threshold. When the discarded traffic exceeds the expected traffic, this alarm occurs. |
almBdLedtest
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13419 | Trap of Alarm:Board LED Flash Test |
almPlaCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13422 | Trap of Alarm: PLA Configuration Mismatch. |
almDot1xRsNoresponse
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13433 | Trap of Alarm: No Response from the RADIUS Server for 802.1X Authentication. |
almDot1xUsernumOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13440 | Trap of Alarm: Number of Users Authenticated by 802.1X Exceeds the Threshold. |
almMacExtExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13444 | Trap of Alarm: Bit error threshold-crossing detected at MAC layer. |
almMringOamLocvW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13445 | Trap of Alarm:West of MPLS Ring loss of connectivity verification |
almMringOamSdW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13451 | Trap of Alarm:West of MPLS Ring signal degrade |
almMringOamSfW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13452 | Trap of Alarm:West of MPLS Ring signal fail |
almMringOamUnexpmegW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13453 | Trap of Alarm:West of MPLS Ring Unexpected MEG |
almMringOamUnexpmepW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13454 | Trap of Alarm:West of MPLS Ring Unexpected MEP |
almMringOamUnexpperW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13455 | Trap of Alarm:West of MPLS Ring Unexpected Period |
almMringOamRdiW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13456 | Trap of Alarm:West of MPLS Ring Remote Defect Indication |
almMringApsLostW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13457 | Trap of Alarm:West of MPLS Ring APS packet lost |
almMringApsMismatchW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13458 | Trap of Alarm:Far-end west of MPLS Ring APS Error |
almMringFarSwFailW
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13460 | Trap of Alarm:Far-end west of MPLS Ring APS Switch Failure |
almMringOamLocvE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13461 | Trap of Alarm:East of MPLS Ring loss of connectivity verification |
almMringOamSdE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13467 | Trap of Alarm:East of MPLS Ring signal degrade |
almMringOamSfE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13468 | Trap of Alarm:East of MPLS Ring signal fail |
almMringOamUnexpmegE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13469 | Trap of Alarm:East of MPLS Ring Unexpected MEG |
almMringOamUnexpmepE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13470 | Trap of Alarm:East of MPLS Ring Unexpected MEP |
almMringOamUnexpperE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13471 | Trap of Alarm:East of MPLS Ring Unexpected Period |
almMringOamRdiE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13472 | Trap of Alarm:East of MPLS Ring Remote Defect Indication |
almMringApsLostE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13473 | Trap of Alarm:East of MPLS Ring APS packet lost |
almMringApsMismatchE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13474 | Trap of Alarm:Far-end east of MPLS Ring APS Error |
almMringFarSwFailE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13476 | Trap of Alarm:Far-end east of MPLS Ring APS Switch Failure |
almEthCfmAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13478 | Received an AIS OAM packet, indicates that the ETH at service level is faulty. |
almUniptpSrcNegoFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13479 | Trap of Alarm:Unicast PTP packet negotiation fails. |
almUniptpSrcLoss
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13480 | Trap of Alarm:The unicast PTP clock source fails. |
almUniptpSrcSwitch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13481 | Trap of Alarm:Switching occurs in the unicast PTP clock source. |
almUsbProcessFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13484 | Trap of Alarm: Failure to recover data from or back up data to a USB disk. |
almNbUnReachable
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13485 | Trap of Alarm: Access neighbor NE failed. |
almBwutilizationOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13486 | Trap of Alarm: Bandwidth utilization over the threshold. |
almDbmsDelete
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13502 | Trap of Alarm: The NE database is deleted. |
almLaserCheckErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13506 | Trap of Alarm: This alarm indicates that the current optical module has a write/read error. |
almTunnelApsOutage
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13507 | Trap of Alarm: Outage of APS Tunnel Protection Group. |
almPwApsDegraded
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13508 | Trap of Alarm: Downgrade of APS PW Protection Group. |
almPwApsOutage
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13509 | Trap of Alarm: Outage of APS PW Protection Group. |
almNeIPConfusion
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13513 | Trap of Alarm: NEIP CONFUSION. |
almSslCertNoEnc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13514 | Trap of Alarm: Certificate file of SSL is not encrypted. |
almNbCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13533 | Trap of Alarm: The configuration are mismatch in the two neighboring NEs. |
almPlaMemberDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13538 | Trap of Alarm: PLA group member faulty. |
almPlaDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13539 | Trap of Alarm: PLA faulty. |
almSubnetRtConflict
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13545 | Trap of Alarm: Subnetwork route conflict. |
almDot1xPrNoresponse
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13550 | Trap of Alarm: No Response from the Proxy for 802.1X Authentication. |
almDot1xPrUserOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13551 | Trap of Alarm: Number of Concurrent Users Authenticated by 802.1X Proxy Exceeds the Threshold. |
almElanSmacFlapping
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13552 | Trap of Alarm: Flapping of source MAC addresses of E-LAN services. |
almPatchBdExclude
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13557 | Trap of Alarm: Exclusion of a patch package board. |
almPatchBdMatchFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13558 | Trap of Alarm: Patch package matching failure. |
almISISADJACENCYCHANGE
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13560 | Trap of Alarm: ISIS adjacency state change. |
almBGPBACKTRANSITION
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13561 | Trap of Alarm: The BGP connection is interrupted.. |
almL3vTrapThreExceed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13562 | Trap of Alarm: Number of prefixes contained in the VPN exceeding the upper threshold. |
almL3vTrapVrfDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13563 | Trap of Alarm: All VPN interfaces being down. |
almVersionNotsupport
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13564 | Trap of Alarm: Not supported by the current version. |
almRtTblLack
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13619 | Trap of Alarm: Insufficient routing table resources. |
almIpfpmLossRatioExce
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13645 | Trap of Alarm: IPFPM packet loss rate exceeding the upper threshold. |
almIpfpmOneDelayExce
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13646 | Trap of Alarm: One-way delay of IPFPM exceeding the upper threshold. |
almIpfpmTwoDelayExce
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13647 | Trap of Alarm: Two-way delay of IPFPM exceeding the upper threshold. |
almEthtrunkMemberDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13655 | Trap of Alarm:EHT-TRUNK member unavailable |
almEthtrunkDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13656 | Trap of Alarm:ETH-TRUNK unavailable |
almOspfNbrStateChange
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13663 | Trap of Alarm: OSPF Neighbor Status Changes. |
almIpfpmInstTlpErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13668 | Trap of Alarm: This alarm is generated when an instance fails to add TLP because of insufficient ACL resources. |
almPlaMemberDownExt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13669 | Trap of Alarm: A member in a PLA group is unavailable. |
almSwdlBdMatchFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13673 | Trap of Alarm: The SWDL_BD_MATCH_FAIL is an alarm indicating that a board fails to match the board software. |
almArpFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13689 | Trap of Alarm: ARP learning failure. |
almRfusdDelayUnequal
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13692 | Trap of Alarm: RFUSD Failed to Provide Main or Diversity Signals with Required Delay Compensation. |
almMplsLdpSessionDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13700 | Trap of Alarm: LDP Session Down. |
almMplsLspTblLack
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13701 | Trap of Alarm:The resources of the MPLS LSP table are insufficient. |
almQueueResLack
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13704 | Trap of Alarm:The queue lacks resources on the board where the LAG resides. |
almCompressMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13705 | The device receives an unrecognized header compression hash conflict ID. |
almLcsTrialPeriod
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13719 | The current NE is within the license trial period that lasts for 90 days. |
almAesMacErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13734 | AES message authentication code error. |
almReflectorIpCnflct
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13736 | The simulated IP address of the reflector is the same as the IP address of another node in the network. |
almPwdEncryptRisk
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13744 | This alarm is generated if the user password encryption mode is MD5 or SHA256 when a user logs in, changes the password, or adds another user. |
almUsbFileUnsec
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13745 | The NE on which the USB flash drive is installed is insecure. |
almProPktFlooding
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13746 | Rates of protocol packets received by a device exceed the upper rate threshold for 30 consecutive seconds. |
almSslCertDamaged
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13759 | Trap of Alarm: User-defined SSL certificate file damaged. |
almArpSpoof
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13762 | Trap of Alarm: ARP spoof. |
almProStatAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13774 | Trap of Alarm: Abnormal Protocal Status. |
almIgspEntriesExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13775 | Trap of Alarm: Threshold-crossing for IGMP snooping multicast entries. |
almSslCertToExpire
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13779 | This alarm is generated when the SSL certificate file is going to expire two months later. |
almPortBerSd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13810 | Trap of Alarm: Port signal degraded |
almServOverFwdCapa
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13891 | Trap of Alarm: This alarm is generated when the total service packet traffic exceeds the hardware forwarding capability. |
almNvVportDown
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13895 | Trap of Alarm: This alarm indicates a connection error between an AP UNI port and a master virtual port and as a result the services on the master virtual port are interrupted. |
almALoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.139 | Trap of Alarm: Loss of clock in the upstream direction of the bus. |
almFlowExcLcs
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13907 | Trap of Alarm: The transmitted traffic exceeds the limitation specified by the license. |
almMwFecExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13916 | Trap of Alarm: Microwave FEC BER exceeding the threshold. |
almPlaPktErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13930 | Trap of Alarm:Error occurs when a PLA group generates packets |
almBrdcastRatioOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13933 | Trap of Alarm: This alarm is generated if the ratio of broadcast and multicast packets to all packets exceeds the threshold. |
almMimoLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13937 | Trap of Alarm: This alarm is generated if the loss of MIMO signal. |
almMimoLineMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13938 | Trap of Alarm: This alarm is generated if the connection error of MIMO line. |
almSoftwareUncommit
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13948 | Trap of Alarm: Decoupling the board software is not authorized. Obtain the authorization first. |
almFldCfgCloseport
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13949 | Trap of Alarm:IF port data services disabled by FLD |
almLaserTypeMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13951 | Trap of Alarm:Optical module type mismatch |
almKmcKeySyncFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13960 | Trap of Alarm: the KMC key fails to be in sync with APPs. |
almInsuffcntMemSpace
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13983 | Trap of Alarm:The space of the memory file system is insufficient. |
almInsuffcntFlshSpace
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13984 | Trap of Alarm:The space of the flash file system is insufficient. |
almStorageFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.13985 | Trap of Alarm:There is an error in the storage. |
almTrLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14 | Trap of Alarm: The clock of the cross-connect board is faulty. |
almIsisLspSeqExceed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14002 | Trap of Alarm:The LSP sequence number has exceeded the upper threshold value. |
almIsisSeqReachMax
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14003 | Trap of Alarm:The LSP sequence number has reached the maximum value. |
almDeviceAuthFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14007 | Trap of Alarm:Device authentication failure. |
almErpsBlock
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14035 | Trap of Alarm:Indicates the blocked port on the EPRS ring when protection switching occurs (under non-idle state). |
almPatchOpTimeout
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14041 | Trap of Alarm:Patch package operation timeout. |
almPatchInitFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14042 | Trap of Alarm:This alarm is generated when the patch initialization fails. |
almPwrAcFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14051 | Trap of Alarm:The AC power fails. |
almPwrAcAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14052 | Trap of Alarm:The PWR_AC_ALARM is an alarm indicating that the AC voltage is beyond the normal range. |
almPwrDcAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14053 | Trap of Alarm:The PWR_DC_ALARM is an alarm indicating that the DC voltage. |
almPwrSurgeAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14054 | Trap of Alarm:AC surge protective device (SPD) is faulty. |
almPwrSolarProt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14055 | Trap of Alarm:This alarm is generated when the Solar locks out due to output. |
almPwrSloarFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14056 | Trap of Alarm:This alarm is generated when the system detects that the input voltage of each PVDU module is lower than 20 V for 24 hours. |
almPwrUpgradeFalled
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14057 | Trap of Alarm:Module upgrade failure. |
almPwrOutputProt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14058 | Trap of Alarm:AC/DC output protection. |
almBatHardFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14059 | Trap of Alarm:The battery hardware is faulty. |
almBatProtAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14060 | Trap of Alarm:This alarm is generated by following reasons:when the battery temperature is low enough and then disconnectes. |
almBatOverdischarge
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14061 | Trap of Alarm:This alarm is generated if battery discharging current exceeds the upper. |
almBatOvercharge
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14062 | Trap of Alarm:This alarm is generated if battery charging current exceeds the upper. |
almBatTempAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14063 | Trap of Alarm:The alarm indicating that the battery temperature is beyond the normal. |
almBatMissing
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14064 | Trap of Alarm:This alarm is generated when no battery is detected. |
almBatSohLow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14065 | Trap of Alarm:The SOH is equal to or less than the SOH self-load value. |
almPwrTmpovrProt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14066 | Trap of Alarm:This alarm is generated if any ESMU battery is undertemperature and the metal oxide semiconductor is disconnected. |
almPwrAcModProt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14067 | Trap of Alarm:The AC module has no output. |
almPwrCommFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14068 | Trap of Alarm:This alarm is generated in case of a failure to communicate with all. |
almPwrHardFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14069 | Trap of Alarm:This alarm is generated in case of an AC module fault, 24 V AC module fault, or 48 V DC module fault. |
almBatAddrConflict
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14070 | Trap of Alarm:If multiple ESMU devices have the same hardware address DIP switch setting, the SMU generates an Address Conflict alarm. |
almBatSohWarning
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14071 | Trap of Alarm:The SOH is equal or less than the SOH sub-health value. |
almPwrLlvdAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14072 | Trap of Alarm:The alarm indicating that the voltage is below the powerdown voltage. |
almDevDoorOpen
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14075 | Trap of Alarm:The cabinet door is open. |
almGpsmodLockFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14077 | Trap of Alarm:The clock of the GPS module fails to lock satellite signals |
almGpsmodInvalid
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14078 | Trap of Alarm:The GPS module fails |
almBatFanAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14082 | Trap of Alarm:This alarm is generated when the patch initialization fails. |
almSepPortFault
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14084 | Trap of Alarm:SEP port fault |
almErpsCfmFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14085 | Trap of Alarm:The MEP bound to an ERPS instance fails |
almPatchMatchNoStart
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14088 | Trap of Alarm:The system control board does not launch a board patch match for specific reasons |
almRSErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.141 | Trap of Alarm: Received Signal Error. |
almDcnChannelBiterror
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14102 | Trap of Alarm:The Bit-ERROR of the DCN channel |
almLptAuthFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14141 | Trap of Alarm:This alarm is generated when LPT authentication fails |
almDcncfgNotCommit
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14147 | Trap of Alarm: The configured DCN subnet ID has not been committed. |
almSrvLoopLd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14149 | Trap of Alarm:This alarm is reported when a loop is detected. This alarm is cleared after the loop is removed |
almPingLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14150 | Trap of Alarm:The destination IP address is unreachable. |
almPingArpMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14151 | Trap of Alarm:The MAC addresses in the static and dynamic ARP entries conflict with each other. |
almErpsNotComplete
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14164 | Trap of Alarm:The alarm indicates that configuration of the EPRS ring is not complete |
almDhcpFreeIpUseUp
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14172 | Trap of Alarm: This alarm is reported when the DHCP server fails to allocate IP addresses because the available IP addresses have been used up. |
almApsStatusIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14174 | Trap of Alarm:The APS_STATUS_INDI alarm indicates the APS status |
almDbUnsave
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14255 | Trap of Alarm:This alarm is reported when configuration persistency occurs in the database in some scenarios. |
almAccessCtrlDisabled
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14262 | Trap of Alarm: Access control is disabled. |
almPtpTimeAdjustOff
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14284 | Trap of Alarm:PTP time synchronization is disabled. |
almGpsLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14285 | Trap of Alarm: There is no signal received from the GPS on this device. |
almCaCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14382 | Trap of Alarm: The configuration of the members in the CA group is inconsistent, or the CA group configuration of the two cascade NEs is inconsistent. |
almErpsHeartDetectFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14400 | Trap of Alarm:ERPS heartbeat detection timeout alarm. |
almBdFileUnsecured
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14407 | Trap of Alarm: The file may be unsecured. |
almComboPortCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14408 | Trap of Alarm: One cascading port is configured in a working group (for example, a CA group), but the other cascading port that is actually connected is not in the working group. |
almEthCfgMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14459 | Trap of Alarm:Ethernet port configurations are inconsistent. |
almIpv4PrefixExceed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.14581 | Trap of Alarm:IPv4 Route Prefix Count Exceeding Limit. |
almCfgVerify
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.147 | Trap of Alarm:configuration not verify |
almRFRst
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.159 | Trap of Alarm: Receiving FIFO Reset. |
almHpCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.16 | Trap of Alarm: High order path bit errors crosses the threshold. |
almTFRst
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.160 | Trap of Alarm: Transmission FIFO Reset. |
almRpLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.163 | Trap of Alarm: Loss Of Receiving Phaselock Ring Clock. |
almTempAlarm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.166 | Trap of Alarm: Temperature over threshold. |
almB1SD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.175 | Trap of Alarm: Regenerator section(B1) signal degraded. |
almK1K2M
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.180 | Trap of Alarm: K1K2 Mismatch. |
almK2M
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.181 | Trap of Alarm: K2 Mismatch. |
almBipSD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.182 | Trap of Alarm: BIP signal degraded. |
almBipExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.183 | Trap of Alarm: BIP excssive errors. |
almExtSyncLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.184 | Trap of Alarm: Loss of External Synchronous Source. |
almDbmsError
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.185 | Trap of Alarm: There is an error in the system database. |
almTd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.189 | Trap of Alarm:Laser transmitter degrade |
almS1SynChange
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.193 | Trap of Alarm: Synchronous source changed in S1 mode. |
almFpgaAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.194 | Trap of Alarm:FPGA Abnormal |
almNeStateInstall
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.197 | Trap of Alarm:NE in install state |
almDbmsProtectMode
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.198 | Trap of Alarm: Databases in protection mode. |
almCommunFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.199 | Inter-board communication failure. |
almSecuAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.200 | The SECU_ALM is an alarm indicating that an illegal user fails to log in to the NE. |
almDownE1Ais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.201 | Trap of Alarm: 2M down signal alarm indication. |
almOCD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.214 | Trap of Alarm: Out of Cell Delineation. |
almNeSfLost
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.215 | Trap of Alarm: Loss of NE software. |
almLCD
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.216 | Trap of Alarm: Loss of cell delimitation. |
almUHCS
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.218 | Trap of Alarm: Uncorrected Header Check Sequence. |
almCHCS
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.219 | Trap of Alarm: Corrected Header Check Sequence. |
almVpAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.226 | Trap of Alarm: VP alam indication signal. |
almVpRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.227 | Trap of Alarm: VP remote defect indicator. |
almVcAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.228 | Trap of Alarm: VC alam indication signal. |
almVcRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.229 | Trap of Alarm: VC remote defect indicator. |
almEthLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.235 | Trap of Alarm: The ETH_LOS is an alarm indicating loss of network port connection. This alarm occurs when the Ethernet network port cannot receive Ethernet signals. |
almHardBad
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.236 | Trap of Alarm: This alarm occurs when the board detects a hardware exception. |
almLoopAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.240 | Trap of Alarm: This alarm occurs when service loopback is set. |
almInPwrAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.25 | Trap of Alarm: Input power abnormal. |
almSwdlPkgNoBdSoft
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2569 | Trap of Alarm: No board software in the software package. |
almSwdlRollbackFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2570 | Trap of Alarm: NE rollback failed. |
almSwdlCommitFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2571 | Trap of Alarm: Commit failure. |
almSwdlInProcess
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2572 | Trap of Alarm: Software downloading in process. |
almSwdlPkgVerMM
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2573 | Trap of Alarm: Inconsistency of software package versions. |
almSwdlAutoMatchInh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.2574 | Trap of Alarm: Automatic match inhibited. |
almOutPwrAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.26 | Trap of Alarm: Output power abnormal. |
almAuCmm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.260 | Trap of Alarm:pointer concatenation mismatch |
almLinkErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.261 | Trap of Alarm: Data link error. |
almWOffline
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.262 | Trap of Alarm:Offline of wrench |
almVoltLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.265 | Trap of Alarm: Loss of voltage. |
almE1Loc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.266 | Trap of Alarm: Loss of upstream 2M clock. |
almTempOver
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.28 | Board working temperature over threshold. |
almTemHa
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.29 | Laser temperature is too high. |
almALS
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.296 | Automatic Laser Shutdown. |
almRLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.3 | Trap of Alarm: Loss of clock. |
almTemLa
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.30 | Laser temperature is too low. |
almInPwrHigh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.31 | Trap of Alarm: Input optical power is too high. |
almInPwrLow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.32 | Trap of Alarm: Input optical power is too low. |
almMsAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.33 | Trap of Alarm: Multiplex section alarm indication. |
almClkNoTraceMode
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.333 | Clock entering into non-tracing running mode. |
almBeffecExc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.335 | Trap of Alarm:Bit errors over threshold before FEC |
almApsManuStop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.336 | Trap of Alarm: MSP protocol is manually stopped. |
almMsRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.34 | Trap of Alarm: Multiplex section remote defect indication. |
almB2Exc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.35 | Trap of Alarm: Multiplex section(B2) excessive errors. |
almBdVerNmat
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.351 | Trap of Alarm:BD_VER_NOT_MATCH |
almB2Sd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.36 | Trap of Alarm: Multiplex section(B2) signal degrade. |
almLaserClosed
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.364 | Trap of Alarm: Laser Closed. |
almC2Vcais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.366 | Trap of Alarm:C2 byte alarm indication |
almC2Pdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.368 | Trap of Alarm:C2 byte defect indication |
almMsRei
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.37 | Trap of Alarm: Multiplex section remote error indication. |
almTestStatus
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.374 | Trap of Alarm:TEST_STATUS |
almBusErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.377 | Trap of Alarm: Bus error. |
almMsCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.38 | Trap of Alarm: Multiplex section performance over threshold. |
almPowerAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.383 | Trap of Alarm: this alarm indicate that the voltage of the board power module is beyond the normal range. |
almSyncLockoff
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.390 | Trap of Alarm:Timing Source in Priority List has been Locked |
almLaserModErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.393 | Trap of Alarm: Wrong laser module |
almTLoc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.4 | Trap of Alarm: Transmit loss of clock. |
almApsIndi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.41 | Trap of Alarm: APS state indication. |
almPowerAbnormal
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.412 | Trap of Alarm: Power abnormal. |
almApsFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.42 | Trap of Alarm: APS protection switching failure. |
almSlaveBad
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.423 | Trap of Alarm: This alarm occurs when the board detects detects a fault of the connector between itself and the standby SCC board. |
almModComFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.432 | Trap of Alarm: Module communicates abnormally. The alarm occurs when the communication of the CPU and other internal modules of the board is abnormal. |
almBiosStatus
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.449 | Trap of Alarm: BIOS status. |
almLpRfi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.48 | Trap of Alarm: Lower order path remote failure indication. |
almLpCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.49 | Trap of Alarm: Low order path bit errors over threshold. |
almROof
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.5 | Out of frame. |
almLpSizeErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.51 | Trap of Alarm: TU structure error.When the mapping structure of the TU services received at the board is inconsistent with that specified for the board, this alarm is reported |
almLsrWillDie
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.56 | Laser will be out of work. |
almLsrNoFited
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.57 | Trap of Alarm: Laser is not installed. |
almNeSoftMM
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.571 | Trap of Alarm: Inconsistency between the active and standby software. |
almSwdlActivatedTimeOut
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.573 | Trap of Alarm: Activation time out. |
almSwdlNePkgCheck
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.574 | Trap of Alarm: the alarm indicate that a file in the software package is lost or the package loading fails to pass the check. |
almSwdlChgmngNoMatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.575 | Trap of Alarm: NE software and the board software do not match. |
almLsrBcmAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.58 | Setover Current of the Laser over Threshold. |
almBootRomBad
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.584 | Trap of Alarm: this alarm indicate the BOOTROM data check failure. During the running of board software, the system periodically checks whether the BOOTROM data is damaged. This alarm occurs when the BOOTROM data is detected damaged. |
almLicenceErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.589 | Trap of Alarm: Licence Error. |
almSyncFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.591 | Trap of Alarm: Batch Backup Failure of the SCC Board Data. |
almChipAbn
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.597 | Trap of Alarm:temperature chip failure |
almNoBdSoft
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.6 | Trap of Alarm: No board software alarm. The alarm occurs when the board does not have the necessary files, for example, loading software, manufacturing information and logic software or the software name is incorrect. |
almLsrCoolAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.60 | Trap of Alarm:Cooling current of the laser over threshold |
almLaserModuleMismatch
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.606 | Trap of Alarm:Laser module is mismatch |
almV5Vcais
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.607 | nul. |
almLpsUniBiM
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.619 | Trap of Alarm: alarm of mismatch in unidirectional operation and bidirectional operation in msp_linear . |
almPatchfileNotexist
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.620 | Trap of Alarm: patchfile not exist . |
almPatchErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.621 | Trap of Alarm: patch error . |
almPatchNotConfirm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.622 | Trap of Alarm:Activated patch has not been confirmed overtime |
almRtcFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.624 | Trap of Alarm: RTC time fail alarm |
almBdNotInstalled
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.625 | Trap of Alarm: Logic board not installed. |
almMwLim
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.626 | Trap of Alarm: Microwave link identifier mismatch. |
almOutPwrHigh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63 | Trap of Alarm:Output optical power too high |
almMwLof
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.631 | Trap of Alarm: microwave loss of frame. |
almRadioTslLow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.635 | Trap of Alarm: Radio transmission level too low. |
almLaserShut
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63509 | Trap of Alarm: Board laser shutdown |
almHardNonSupport
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63537 | Trap of Alarm: This alarm is reported when the hardware does not support the configuration delivered by the SCC board. |
almVcatLoa
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63538 | Trap of Alarm: The VCAT_LOA is an alarm indicating that the delay of the virtual concatenation is over long. This alarm occurs when the delay time of the timeslots bound to a VC trunk exceeds the time allowed by the virtual concatenation delay. The time allowed by the virtual concatenation delay depends on different board types. |
almAlmLFA
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63554 | The LFA is an alarm indicating the loss of E1 basic frame alignment. This alarm indicates that the E1 double frame is failed in basic frame delimitation and that the delimitation synchronous status is lost. |
almDdnLfa
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63555 | The DDN_LFA is an alarm indicating the loss of frame alignment in the PDH framed E1 services on the electrical interface side. When the electrical interface side fails to receive the frame alignment signals in the framed E1 services, the DDN_LFA alarm is reported. |
almAlmLMFA
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63558 | The LMFA is an alarm indicating the loss of E1 multiframe alignment. This alarm indicates that the E1 CRC-4 frame is failed in multiframe delimitation and that the delimitation synchronous status is lost. |
almAlmRMFA
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63563 | The RMFA is an alarm that the framing E1/T1 multiframe notification event occurs. If the framing E1/T1 signals occur in consecutive Z (Z is from two through five) CAS multiframe cycles, the RMFA alarm is reported when all the CAS multiframe mutual-notification bits of the input signals are set to 1. |
almFcsErr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63575 | Trap of Alarm: The FCS_ERR is an alarm indicating the FCS check error. When there is an error in the frame check sequence (FCS) check performed for the GFP frames received, this alarm occurs. |
almB3ExcVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63577 | Trap of Alarm: B3 bit errors in the lower order path VC-3 crosses the threshold of B3_EXC. |
almB3ExcVc4
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63578 | Trap of Alarm:B3 bit errors in the VC-4 path crosses the threshold |
almB3SdVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63579 | Trap of Alarm: B3 bit errors in the lower order path VC-3 crosses the threshold of B3_SD. |
almB3SdVc4
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63580 | Trap of Alarm:B3 bit errors in the VC-4 path crosses the threshold |
almVcatlomVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63584 | Trap of Alarm: The VCAT_LOM_VC12 is an alarm indicating the loss of the virtual concatenation multiframe in the VC-12 path. This alarm occurs when the system detects that the multiframe indicator (MFI) field in the K4 byte of the VC-12 timeslot is illegal. |
almVcatLomVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63585 | Trap of Alarm: The VCAT_LOM_VC3 is an alarm indicating the loss of the virtual concatenation multiframe in the VC-3 path. This alarm occurs when the system detects that the multiframe indicator (MFI) field in the H4 byte of the VC-3 timeslot is illegal. |
almVcatLomVc4
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63586 | Trap of Alarm:VCAT_LOM_VC4 |
almVCATSQMVC12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63587 | Trap of Alarm: The VCAT_SQM_VC12 is an alarm indicating the sequence mismatch of the virtual concatenation in the VC-12 path. This alarm occurs when the serial numbers of members in the virtual concatenation at the VC-12 level mismatch. |
almVCATSQMVC3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63588 | Trap of Alarm: The VCAT_SQM_VC3 is an alarm indicating the sequence mismatch of the virtual concatenation in the VC-3 path. This alarm occurs when the serial numbers of members in the virtual concatenation at the VC-3 level mismatch. |
almVcatSqmVc4
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63589 | Trap of Alarm:VCAT_SQM_VC4 |
almLpRdiVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63590 | Trap of Alarm: The LP_RDI_VC12 is a remote defect indication alarm in the lower order path. If a board has detected that bit 8 of the V5 byte in the VC-12 lower order path is 1, the LP_RDI_VC12 alarm is reported. |
almLpRdiVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63591 | Trap of Alarm: The LP_RDI_VC3 is a remote defect indication alarm in the lower order path. If a board has detected that bit 5 of the G1 byte in the VC-3 lower order path is 1, the LP_RDI_VC3 alarm is reported. |
almLpReiVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63592 | Trap of Alarm: The LP_REI_VC12 is a remote error indication alarm in the lower order path. If a board has detected that bit 3 of the V5 byte is 1, the LP_REI_VC12 alarm is reported. |
almLpReiVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63593 | Trap of Alarm: The LP_REI_VC3 is a remote error indication alarm in the lower order path. If a board has detected a 1 in any of (bit1,bit2,bit3,bit4) of the G1 byte, the LP_REI_VC3 alarm is reported. |
almLpSlmVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63594 | Trap of Alarm: The LP_SLM_VC12 is a signal label mismatch alarm in the VC-12 lower order path. If a board has detected that the signal label mismatch event occurs in the V5 byte, the LP_SLM_VC12 alarm is reported. |
almLpSlmVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63595 | Trap of Alarm: The LP_SLM_VC3 is a signal label mismatch alarm in the VC-3 lower order path. If a board has detected that the signal label mismatch event occurs in the C2 byte, the LP_SLM_VC3 alarm is reported. |
almLpTimVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63596 | Trap of Alarm: The LP_TIM_VC12 is a trace identifier mismatch alarm in the VC-12 lower order path. If a board has detected that the J2 byte does not match, the LP_TIM_VC12 alarm is reported. |
almLpTimVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63597 | Trap of Alarm: The LP_TIM_VC3 is a trace identifier mismatch alarm in the VC-3 lower order path. If a board has detected that the J1 byte does not match, the LP_TIM_VC3 alarm is reported. |
almLpUneqVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63598 | Trap of Alarm: The LP_UNEQ_VC12 is an alarm indicating no payload is equipped in the lower order path. If a board has detected that the signal label in the V5 byte is 0, the LP_UNEQ_VC12 alarm is reported. |
almLpUneqVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63599 | Trap of Alarm: The LP_UNEQ_VC3 is an alarm indicating no payload is equipped in the lower order path. If a board has detected that the signal label in the C2 byte is 0, the LP_UNEQ_VC3 alarm is reported. |
almRadioTslHigh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.636 | Trap of Alarm: Radio transmission level too high. |
almTuAisVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63600 | Trap of Alarm: The TU_AIS_VC12 is a TU alarm indication signal in the VC-12 lower order path. TU alarm indication is the VC-12 path AIS. If a board has detected that the TU path is all '1's, the TU_AIS_VC12 alarm is reported. |
almTuAisVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63601 | Trap of Alarm: The TU_AIS_VC3 is a TU alarm indication signal in the VC-3 lower order path. TU alarm indication is the VC-3 path AIS. If a board has detected that the TU path is all '1's, the TU_AIS_VC3 alarm is reported. |
almTuLopVc12
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63602 | Trap of Alarm: The TU_LOP_VC12 is an alarm indicating the loss of TU pointer in the VC-12 lower order path. If a board has detected that the TU-PTR value is an invalid pointer or NDF reversion in eight consecutive frames, the TU_LOP_VC12 alarm is reported. |
almTuLopVc3
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63603 | Trap of Alarm: The TU_LOP_VC3 is an alarm indicating the loss of TU pointer in the VC-3 lower order path. If a board has detected that the TU-PTR value is an invalid pointer or NDF reversion in eight consecutive frames, the TU_LOP_VC3 alarm is reported. |
almAlmImaLif
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63614 | Trap of Alarm: ALM_IMA_LIF. |
almAlmImaLods
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63615 | Trap of Alarm: ALM_IMA_LODS. |
almAlmImaRfi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63616 | Trap of Alarm: ALM_IMA_RFI. |
almAlmImaReTxUnusable
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63617 | Trap of Alarm: ALM_IMA_RE_TX_UNUSABLE. |
almAlmImaReRxUnusable
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63618 | Trap of Alarm: ALM_IMA_RE_RX_UNUSABLE. |
almAlmE1Rai
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63622 | Trap of Alarm: E1 Remote Alam Indicator. |
almPortModuleOffline
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63629 | Trap of Alarm: No optical or electrical module is in position when the port is enabled. |
almThunderAlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63635 | Trap of Alarm: Thunder protection circuit failure alarm. The alarm occurs when the board detects a lightning circuit failure. |
almGfpDlfd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63638 | Trap of Alarm: The ALM_GFP_dLFD is an alarm indicating GFP loss of frame delineation. When GFP frames are detected out of synchronization, this alarm occurs. |
almGfpDcsf
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63639 | Trap of Alarm: The ALM_GFP_dCSF is an alarm indicating GFP loss of client signal. When the source end cannot receive the client signal, it sends the management frame to the sink end. When the sink end receives the management frame, this alarm occurs. |
almAlmGfpdssf
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63640 | Trap of Alarm:GFP Loss of Client Character Synchronization |
almLaserModErrEx
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63644 | Trap of Alarm: Laser Mode Error. |
almLcasFop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63646 | Trap of Alarm: Failure of LCAS protocol. |
almLcasPlct
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63647 | Trap of Alarm: The LCAS_PLCT is an alarm indicating partial loss of capacity in the LCAS transmit direction. When the LCAS function of the VCTRUNK is enabled, in the transmit direction, the number of paths that carry load is less than the number of paths configured and is not zero. |
almLcasTlct
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63648 | Trap of Alarm: The LCAS_TLCT is an alarm indicating total loss of capacity in the LCAS transmit direction. When the LCAS function of the VCTRUNK is enabled, in the transmit direction, the number of paths that carry load is zero, whereas the number of paths configured is not zero. |
almLcasPlcr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63649 | Trap of Alarm: The LCAS_PLCR is an alarm indicating partial loss of capacity in the LCAS receive direction. When the LCAS function of the VCTRUNK is enabled, in the receive direction, the number of paths that carry load is less than the number of paths configured and is not zero. |
almLcasTlcr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63650 | Trap of Alarm: The LCAS_TLCR is an alarm indicating the total loss of capacity in the LCAS receive direction. When the LCAS function of the VCTRUNK is enabled, in the receive direction, the number of paths that carry load is zero, whereas the number of paths configured is not zero. |
almLcasFopt
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63651 | Trap of Alarm: The LCAS_FOPT is an alarm indicating the failure of the LCAS protocol in the transmit direction. When the source end of the LCAS module detects abnormalities, the LCAS negotiation is unavailable or incorrect and this alarm occurs. |
almLcasFopr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63652 | Trap of Alarm: The LCAS_FOPR is an alarm indicating the failure of the LCAS protocol in the receive direction. When the sink end of the LCAS module detects abnormalities, the LCAS negotiation is unavailable or incorrect and this alarm occurs. |
almLptIneffect
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.63656 | Trap of Alarm: LPT function failure. |
almRadioRslHigh
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.637 | Trap of Alarm: Radio receive level too high. |
almRadioRslLow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.638 | Trap of Alarm: Radio receive level too low |
almRadioMute
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.639 | Trap of Alarm: radio transmission mute. |
almOutPwrLow
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.64 | Trap of Alarm: Output optical power too low. |
almConfigNoSupport
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.640 | Trap of Alarm: configuration not support. |
almWsLos
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.644 | Trap of Alarm:wayside interface los of signal |
almNeDCNMode
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.65528 | Trap of Alarm: The device is working under DCN mode. |
almAuLop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.66 | Trap of Alarm: AU loss of pointer. When eight NDF frames or invalid pointer values are consecutively received on the receive side of the local optical interface, this alarm is reported. |
almMsAdCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.67 | Trap of Alarm: Multiplex Section Adaptation Performance Over Threshold. |
almB3Sd
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.70 | Trap of Alarm: High order path B3 signal degraded. |
almB3Exc
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.71 | Trap of Alarm: Working temperature of the pump laser over threshold. |
almAuAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.72 | Trap of Alarm: AU alarm indication. |
almHpUneq
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.75 | Trap of Alarm: No loading error in the higher order path. |
almHpTim
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.76 | Trap of Alarm: Higher order path tracking identification mismatch. |
almHpSlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.77 | Trap of Alarm: Higher order path signal identification mismatch. |
almHpRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.78 | Trap of Alarm: High order path remote defect indication. |
almHpRei
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.79 | Trap of Alarm: High order path remote error indication. |
almRLof
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.8 | Trap of Alarm: Loss of frame on receiving line. |
almHpLom
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.81 | Trap of Alarm: Higher order Path Loss of Multiframe. |
almTuLop
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.82 | Trap of Alarm: TU Loss of Pointer. |
almTuAis
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.83 | Trap of Alarm: TU alarm indication. |
almHpAdCrossTr
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.84 | Trap of Alarm: High order path adaption performance over threshold. |
almJ0Mm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.87 | Trap of Alarm: Trace identifier mismatch. |
almLpRFifo
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.88 | Trap of Alarm: FIFO overflow on the receiving side of the lower order path. |
almLpTFifo
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.89 | Trap of Alarm: FIFO overflow on the transmission side of the lower order path. |
almTF
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.9 | Laser Transmission Failure. |
almLpUneq
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.90 | Trap of Alarm: No payload indication of the lower order path. |
almLpTim
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.91 | Trap of Alarm: Lower order path tracking identification mismatch. |
almLpSlm
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.92 | Trap of Alarm: Lower order path signal label mismatch. |
almLpRdi
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.93 | Trap of Alarm: Low order path remote defect indication. |
almLpRei
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.94 | Trap of Alarm: Low order path remote error indication. |
almWRFail
| .1.3.6.1.4.1.2011.2.25.3.40.40.40.99 | Trap of Alarm: this is an alarm indicating the failure of reading and writing the chip register |
trapsAlm 