OMNITRON-GPOE-NOTIFICATION-MIB

        Omnitron GPoE Notification MIB for use with v2.0 GPoE and GHPoE
and NetOutlook
        
Copyright 2018 Omnitron Systems Technology, Inc.
All rights reserved

Imported Objects

omnitronOMNITRON-TC-MIB
MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUPSNMPv2-CONF
MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Unsigned32SNMPv2-SMI
DisplayStringSNMPv2-TC

Objects

omnitronGpoeNotificationMib .1.3.6.1.4.1.7342.100
ostGpoeNotificationCodes .1.3.6.1.4.1.7342.100.0
ostGpoeNotificationObjects .1.3.6.1.4.1.7342.100.1
gpoeTrapCode .1.3.6.1.4.1.7342.100.1.1
gpoeTrapIpString .1.3.6.1.4.1.7342.100.1.2
gpoeTrapModuleDescription .1.3.6.1.4.1.7342.100.1.3
gpoeSourceIpString .1.3.6.1.4.1.7342.100.1.4
gpoeUsername .1.3.6.1.4.1.7342.100.1.5
gpoePoeStatus .1.3.6.1.4.1.7342.100.1.6
ostGpoeNotificationGlobalObjects .1.3.6.1.4.1.7342.100.2
ostGpoeNotificationCfgSetClearAll .1.3.6.1.4.1.7342.100.2.1
ostGpoeNotificationCfgTable .1.3.6.1.4.1.7342.100.3
ostGpoeNotificationCfgEntry .1.3.6.1.4.1.7342.100.3.1
gpoeNotificationCfgTrapNum .1.3.6.1.4.1.7342.100.3.1.1
gpoeNotificationCfgFilteringEnable .1.3.6.1.4.1.7342.100.3.1.2
ostGpoeNotificationCompliances .1.3.6.1.4.1.7342.100.4
ostGpoeNotificationGroups .1.3.6.1.4.1.7342.100.5

Notifications/Traps

NameOIDDescription
gpoeModuleColdStart



.1.3.6.1.4.1.7342.100.0.1
Module cold start - A module has completed power on testing after
initial power up, where gpoeTrapCode = 0.
gpoeSecondaryLinkUp



.1.3.6.1.4.1.7342.100.0.10
Secondary link up - Secondary or backup redundant link port is active,
where gpoeTrapCode indicates the port number.
gpoeSecondaryLinkDown



.1.3.6.1.4.1.7342.100.0.11
Secondary link down - Secondary or backup redundant link port is down,
where gpoeTrapCode indicates the port number.
gpoeStandbyLinkUp



.1.3.6.1.4.1.7342.100.0.12
Standby link up - Standby redundant link port is up and can become an
active link if the primary link goes down, where gpoeTrapCode
indicates the port number.
gpoeStandbyLinkDown



.1.3.6.1.4.1.7342.100.0.13
Standby link down - Standby redundant link port is down and cannot
become an active link if the primary link goes down, where
gpoeTrapCode indicates the port number.
gpoeLoopPreventionBlock



.1.3.6.1.4.1.7342.100.0.14
Loop prevention block - Loop prevention block on a port has occurred
(RSTP block), where gpoeTrapCode indicates the port number.
gpoeLoopPreventionClear



.1.3.6.1.4.1.7342.100.0.15
Loop prevention clear - Loop prevention block on a port has been
removed (RSTP forward), where gpoeTrapCode indicates the port number.
gpoeHardwareDipSwitchChanged



.1.3.6.1.4.1.7342.100.0.16
Hardware DIP switch changed - Hardware DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number.
gpoeSoftwareDipSwitchChanged



.1.3.6.1.4.1.7342.100.0.17
Software DIP switch changed - Software DIP switch on the module has
changed state, where gpoeTrapCode indicates the switch number.
gpoeOutputRelay



.1.3.6.1.4.1.7342.100.0.18
Output relay - Output relay changed state, either from activated
to not activated or not activated to activated, where
gpoeTrapCode indicates the relay state:
  1 = not activated,
  2 = activated
gpoeInputPinStatus



.1.3.6.1.4.1.7342.100.0.19
Input pin status - Input pin changed state, either open to closed
or closed to open, where gpoeTrapCode indicates the relay state:
  1 = open,
  2 = closed
gpoeModuleReset



.1.3.6.1.4.1.7342.100.0.2
Module reset - a module completed power on testing after receiving
a reset command via user intervention, where gpoeTrapCode = 0.
gpoeModuleConfigurationChange



.1.3.6.1.4.1.7342.100.0.20
Module configuration change - A configuration change has been committed
to flash, where gpoeTrapCode = 0.
gpoeModuleOverTemperature



.1.3.6.1.4.1.7342.100.0.21
Module over temperature - The module has detected that the module
temperature has risen above the safe operating temperature, which is 5
degrees less than the maximum temperature supported and is not
generated again unless the module first detects an operating
temperature five degrees below the over temperature threshold, where
gpoeTrapCode = 0.
gpoeModuleNormalTemperature



.1.3.6.1.4.1.7342.100.0.22
Module normal temperature - The module has detected a normal operating
temperature range after a temperature out of range (low or high), where
gpoeTrapCode = 0.
gpoeModuleVoltageOutOfRange



.1.3.6.1.4.1.7342.100.0.23
Module voltage out of range - The module has detected that the internal
operating voltage is greater than 5% or less than 5% of nominal
internal voltage and the event is not generated again unless the module
first detects a safe operating voltage for more than 1 sec, where
gpoeTrapCode = 0.
gpoeModuleVoltageRangeNormal



.1.3.6.1.4.1.7342.100.0.24
Module voltage range normal - The module has detected a normal voltage
range after a voltage out of range (low or high), where
gpoeTrapCode = 0.
gpoePoePdStatusError




.1.3.6.1.4.1.7342.100.0.25
PoE PD status error - A port on the module has detected a PoE PD
error, where gpoePoeStatus indicates the specific PoE PD error and
gpoeTrapCode indicates the port number.
gpoePoePdStatusNormal




.1.3.6.1.4.1.7342.100.0.26
PoE PD status normal - A port on the module has detected no PoE PD
errors on a port where previously there had been one or more errors,
where gpoeTrapCode indicates the port number.
gpoeAclAccessDenied




.1.3.6.1.4.1.7342.100.0.27
ACL access denied - The module has detected that access to the
management has been denied using a configured or default ACL, where
gpoeSourceIpString indicates the source IP address of the access, and
gpoeTrapCode = 0.
gpoeTelnetAuthenticationFailure





.1.3.6.1.4.1.7342.100.0.28
Telnet authentication failure - The module has detected a Telnet
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeTelnetSessionStarted





.1.3.6.1.4.1.7342.100.0.29
Telnet session started - The module has detected that a Telnet session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeTelnetSessionStopped





.1.3.6.1.4.1.7342.100.0.30
Telnet session stopped - The module has detected that a Telnet session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeFtpAuthenticationFailure





.1.3.6.1.4.1.7342.100.0.31
FTP authentication failure - The module has detected an FTP
authentication login failure, where gpoeSourceIpString indicates the
source IP address of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeFtpSessionStarted





.1.3.6.1.4.1.7342.100.0.32
FTP session started - The module has detected that a FTP session
has started, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeFtpSessionStopped





.1.3.6.1.4.1.7342.100.0.33
FTP session stopped - The module has detected that a FTP session
has stopped, where gpoeSourceIpString indicates the source IP address
of the access, gpoeUsername indicates the username,
and gpoeTrapCode = 0.
gpoeSerialConsoleSessionStarted




.1.3.6.1.4.1.7342.100.0.34
Serial console port session started - The module has detected that a
serial console session has started, where gpoeUsername indicates the
username and gpoeTrapCode = 0.
gpoeSerialConsoleSessionStopped




.1.3.6.1.4.1.7342.100.0.35
Serial console port session stopped - The module has detected that a
serial console session has stopped, where gpoeUsername indicates the
username and gpoeTrapCode = 0.
gpoeSshAuthenticationFailure





.1.3.6.1.4.1.7342.100.0.36
SSH authentication failure - Wrong SSH authentication type or password
is used, where gpoeSourceIpString indicates the source IP address,
gpoeUsername indicates the username, and gpoeTrapCode = 0.
gpoeSshSessionStarted





.1.3.6.1.4.1.7342.100.0.37
SSH session started - SSH session for a user has started, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0.
gpoeSshSessionStopped





.1.3.6.1.4.1.7342.100.0.38
SSH session stopped - SSH session for a user has stopped, where
gpoeSourceIpString indicates the source IP address, gpoeUsername
indicates the username, and gpoeTrapCode = 0.
gpoeWrongPasswordCountExceeded





.1.3.6.1.4.1.7342.100.0.39
Wrong password count exceeded - The module has detected too many wrong
password attempts (5) and will not validate any password attempts until
the device times out (5 minutes) or a session is aborted/closed by the
user. This is applicable for Serial port (Console), Telnet, FTP, and
SSH passwords, where gpoeSourceIpString indicates the source IP address,
gpoeUsername indicates the username, and gpoeTrapCode = 0.
gpoeModulePowerRemoved



.1.3.6.1.4.1.7342.100.0.4
Module power removed - The module has detected that incoming voltage
has been removed from a power input or has dropped to zero and is not
generated again unless the module first detects a safe operating
voltage for more than 1 sec, where gpoeTrapCode indicates
the power input.
gpoeSfpInserted



.1.3.6.1.4.1.7342.100.0.40
SFP inserted - SFP has been inserted into a port, where
gpoeTrapCode indicates the port number.
gpoeSfpRemoved



.1.3.6.1.4.1.7342.100.0.41
SFP removed - SFP has been removed from a port, where gpoeTrapCode
indicates the port number.
gpoeSfpTxLowThreshold



.1.3.6.1.4.1.7342.100.0.42
SFP transmit low threshold - SFP has detected that the transmission
power on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpTxHighThreshold



.1.3.6.1.4.1.7342.100.0.43
SFP transmit high threshold - SFP has detected that the transmission
power on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpCurrentBiasLowThreshold



.1.3.6.1.4.1.7342.100.0.44
SFP current bias low threshold - SFP has detected that the current
bias on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpCurrentBiasHighThreshold



.1.3.6.1.4.1.7342.100.0.45
SFP current bias high threshold - SFP has detected that the current
bias on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfp33VLowThreshold



.1.3.6.1.4.1.7342.100.0.46
SFP 3.3V low threshold - SFP has detected that the 3.3V source
voltage on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfp33VHighThreshold



.1.3.6.1.4.1.7342.100.0.47
SFP 3.3V high threshold - SFP has detected that the 3.3V source
voltage on a port is higher than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpTempLowThreshold



.1.3.6.1.4.1.7342.100.0.48
SFP low temperature threshold - SFP has detected that the low
temperature on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpTempHighThreshold



.1.3.6.1.4.1.7342.100.0.49
SFP high temperature threshold - SFP has detected that the high
temperature on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeModulePowerApplied



.1.3.6.1.4.1.7342.100.0.5
Module power applied - The module has detected that incoming voltage
has been applied to a power input and is not generated again unless
the module first detects that the power has been removed for more
than 1 sec, where gpoeTrapCode indicates the power input.
gpoeSfpRxLowThreshold



.1.3.6.1.4.1.7342.100.0.50
SFP receive low threshold - SFP has detected that the receive
power on a port is less than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpRxHighThreshold



.1.3.6.1.4.1.7342.100.0.51
SFP receive high threshold - SFP has detected that the receive
power on a port is greater than the configured threshold warning and
is not generated again unless the module first detects a normal
operating value, where gpoeTrapCode indicates the port number.
gpoeSfpNormal



.1.3.6.1.4.1.7342.100.0.52
SFP normal - SFP has detected normal operating conditions for the
port, where gpoeTrapCode indicates the port number.
gpoeModuleConfigurationFileCorrupted



.1.3.6.1.4.1.7342.100.0.53
Module configuration file corrupted - The management module has
detected a corrupted configuration file, where gpoeTrapCode = 0.
gpoeLinkDown



.1.3.6.1.4.1.7342.100.0.6
Link down - A port on the module has lost link, where gpoeTrapCode
indicates the port number.
gpoeLinkUp



.1.3.6.1.4.1.7342.100.0.7
Link up - A port on the module has gained link, where gpoeTrapCode
indicates the port number.
gpoePrimaryLinkUp



.1.3.6.1.4.1.7342.100.0.8
Primary link up - Primary redundant link port is active, where
gpoeTrapCode indicates the port number.
gpoePrimaryLinkDown



.1.3.6.1.4.1.7342.100.0.9
Primary link down - Primary redundant link port is down, where
gpoeTrapCode indicates the port number.