NETI-ITS-MIB Table View

Table with all service interfaces that is detected by the
device.  The table contains configuration objects common to
all types of interfaces.

itsIfEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.2.1

One interface is represented by one conceptual row in the table.
Rx and Tx is always relative the application domain.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfIndex The index in the table. The index is maintained across re-boots. The index is a positive integer value.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.1
itsIfIfIndex A reference to the index in the ifTable in the IF-MIB. If this is not known, the value is 0.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.2
itsIfName The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's console. This might be a…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.3
itsIfDescr A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software. This description would be the sa…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.4
itsIfSpeed The interface's capacity in bits per second. This value would be the same as presented by the object ifSpeed in the ifTable.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.5
itsIfSuppressAlarm The alarm suppression mode. When alarms are suppressed, no alarms will be generated if a fault situation is detected on the interface. Failures will still be shown by the object itsIfFailure. notSupported…	Enumerationr/w Enumerated Values: 0 notSupported 1 none 2 warning 3 all	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.6
itsIfLoopMode Loop-back mode of the interface. When the loop-back mode is changed to line(2) or dtm(3), a timer is initialized with the value of itsIfLoopTime. The loop-back mode is reset to none(1) when the timer runs out. …	Enumerationr/w Enumerated Values: 0 notSupported 1 none 2 line 3 dtm	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.7
itsIfLoopTimedeprecated Timer for the loop-back mode. The loop-back mode is reset to its normal mode none(0) after the specified number of seconds. A timer value of 0 indicates infinite time, which means that the interface stays in loop-back m…	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.8
itsIfCapabilities Capabilities of the interface. The corresponding bit is set if the capability is supported by the interface. multicast(0). It is possible to use in multicast connection. allowProtection(1).…	Bits Enumerated Values: 0 multicast 1 allowProtection 2 requireCapacity 3 channelPM 4 interfacePM 5 ttp 6 mon 7 loopl 8 loopd 9 sdi1483 10 sdi1485 11 sdi288 12 sdi270 13 sdi2967 14 sdi2970 15 fs 16 avrs 19 madi 20 ref 21 j2kEnc 22 j2kDec 23 hitps 24 psType3 25 dvrs 31 compatible	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.9
itsIfProperties Properties on the interface. A property can only be set if the interface supports has the corresponding capability. The capabilities of the interface can be determined by examine itsIfCapabilities. Curr…	Bitsr/w Enumerated Values: 0 tbd	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.10
itsIfDefects Defects indicated on the interface since the last time the object was read. los(0) Loss of Signal was detected. lof(1) Loss of Frame was detected. ais(2). Alarm Indication Si…	Bits Enumerated Values: 0 los 1 lof 2 ais 3 lop 4 lod 5 rdi 6 lol	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.11
itsIfFailure A textual string describing a fault status on the interface. The object presents an empty string if there are no faults on the interface.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.12
itsIfPMReference A reference to an object that presents performance data for the interface. The object is not part of this MIB.	SNMPv2-TCRowPointer Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.13
itsIfOperStatus The operational state of the interface. This is the same as the object ifOperStatus in the ifTable. up(1). The interface passes data and is used by a TTP. down(2). The interface is down. If…	Enumeration Enumerated Values: 1 up 2 down 4 unknown 5 dormant 6 notPresent	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.14
itsIfTxMuteOnFault Controls the interface output in case of a fault. notSupported(0). The interface does not support control of transmitter on fault. This value can only be read, and can never be written. ena…	Enumerationr/w Enumerated Values: 0 notSupported 1 enable 2 disable 3 freeze	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.15
itsIfPurpose A string presenting the purpose of the TTP that is actively (trying) to use the interface. If no TTP is using the interface, then the purpose is empty. If an interface can be used as input and output interface at the …	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.16
itsIfInterfaceType Denotes the type of interface.	Enumeration Enumerated Values: 1 pdh 2 sdh 3 sdi 4 dvb 5 aes 6 mon	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.17
itsIfMembersSrc A list of values of the itsSrcTtpIndex for the source trail termination points (TTPs) that are actively connected to this interface. A TTP can only be connected to an interface if its administrative state is `up'.	ItsTtpIndexList Type Constraints: range: 0 range: 4 range: 8	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.18
itsIfMembersSnk A list of values of the itsSnkTtpIndex for the sink trail termination points (TTPs) that are actively connected to this interface. A TTP can only be connected to an interface if its administrative state is `up'.	ItsTtpIndexList Type Constraints: range: 0 range: 4 range: 8	.1.3.6.1.4.1.2928.6.2.16.1.1.2.1.19

Table with PDH interfaces.  The table contains configuration
objects specific for PDH interfaces.  The table is indexed using
the same index as the itsIfTable.

itsIfPdhEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.3.1

One PDH interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfPdhSignal Selects type of signal to transport, E3 or DS3.	Enumerationr/w Enumerated Values: 1 e3 2 ds3	.1.3.6.1.4.1.2928.6.2.16.1.1.3.1.1
itsIfPdhFraming Selects the type of framing to use. The valid values depend on selection of type on `itsIfPdhType'. none(1). No framing. g751(2). Only valid for E3. g832(3). Only valid fo…	Enumerationr/w Enumerated Values: 1 none 2 g751 3 g832 4 cbit 5 m13	.1.3.6.1.4.1.2928.6.2.16.1.1.3.1.2

Table with SDH interfaces.  The table contains configuration
objects specific for SDH interfaces.  The table is indexed using
the same index as the itsIfTable.

itsIfSdhEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.4.1

One SDH interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfSdhTiming Selects timing mode for the interface, i.e. clock source in transmission path.	Enumerationr/w Enumerated Values: 1 loop 2 internal	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.1
itsIfSdhMode Sets SDH or SONET interface mode.	Enumerationr/w Enumerated Values: 1 sdh 2 sonet	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.2
itsIfSdhSs Payload mapping type.	Unsigned32r/w Constraints: range: 0-3	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.3
itsIfSdhS1 Synchronization message to send to external equipment in transmission path. This defines the quality level of the clock used to transmit data.	Unsigned32r/w Constraints: range: 0-15	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.4
itsIfSdhSoh A string containing the values of some section overhead bytes. The byte values are on the format byte name, equal sign, byte value. The values are then separated by a single space character. I.e. the format is `S1=n …	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.5
itsIfSdhPoh A string containing the values of some path overhead bytes. The byte values are on the format byte name, equal sign, byte value. The values are then separated by a single space character. I.e. the format is `B3=n G1=n…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.6
itsIfSdhJc A string containing the values of some justification counters. The byte values are on the format counter name, equal sign, byte value. The values are then separated by a single space character. I.e. the format is `RP…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.4.1.7

Table with DVB interfaces.  The table contains configuration
objects specific for DVB interfaces.  The table is indexed using
the same index as the itsIfTable.

itsIfDvbEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.5.1

One DVB interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfDvbFormat A textual string in a non-formal format describing the format of the data.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.5.1.1
itsIfDvbOutputMode Selects output mode.	Enumerationr/w Enumerated Values: 1 auto 2 burst 3 spread	.1.3.6.1.4.1.2928.6.2.16.1.1.5.1.2

Table with AES interfaces.  The table contains configuration
objects specific for AES interfaces.  The table is indexed
using the same index as the itsIfTable.

itsIfAesEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.6.1

One AES interface is represented by one conceptual row in the
table.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfAesIsTimingProvider Selects whether the interface will be used primarily as as timing provider for other interfaces on the same board. This object is applicable only if the interface supports reference locking, i.e. if the `ref' bit is se…	Enumerationr/w Enumerated Values: 0 no 1 wordClock	.1.3.6.1.4.1.2928.6.2.16.1.1.6.1.1
itsIfAesReference Selects the source interface to use as timing reference for output alignment. The source can be any other interface on the same board except itself. The value is the relative interface number on the board, where the f…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.6.1.2

Table with SDI video interfaces.  The table contains configuration
objects specific to SDI interfaces.  The table is indexed using the
same index as the itsIfTable.

itsIfSdiEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.7.1

One SDI interface is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfSdiFormat Video source format. The format is presented as `<pixels-per-line>x<lines-per-frame><i/p> @ <freq> Hz' E.g. `1920x1080p @ 30 Hz' The string is empty if no format is detected.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.1
itsIfSdiAutoSense Controls whether autosense of the input/output signal shall be enabled or not. notSupported(0). The interface does not support autosense. enable(1). Autosense is enabled. Input or output…	Enumerationr/w Enumerated Values: 0 notSupported 1 enable 2 disable	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.2
itsIfSdiIsTimingProvider Selects whether the interface will be used primarily as as timing provider for other interfaces on the same board. This object is applicable only if the interface supports analog video reference signal, or digital vid…	Enumerationr/w Enumerated Values: 0 no 1 analog 2 digital	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.3
itsIfSdiReference Selects the source interface to use as timing reference for output alignment. The source can be any interface on the same board. The value is the relative interface number on the board, where the first interface on th…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.4
itsIfSdiFsVDelayobsolete Adjusts the vertical output delay in number of lines. This object is applicable only if the interface supports reference locking, i.e. if the `ref' bit is set in itsIfCapabilities.	Integer32r/w Constraints: range: -3-1124	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.5
itsIfSdiFsHDelayobsolete Adjusts the horizontal output delay in number of pixels. This object is applicable only if the interface supports reference locking, i.e. if the `ref' bit is set in itsIfCapabilities.	Integer32r/w Constraints: range: -3865-259	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.6
itsIfSdiFsDelay Adjusts the output delay in number of nanoseconds. This object is applicable only if the interface supports reference locking, i.e. if the `ref' bit is set in itsIfCapabilities.	Integer32r/w Constraints: range: -20854167-20854167	.1.3.6.1.4.1.2928.6.2.16.1.1.7.1.7

Table with monitor interfaces.  The table contains
configuration objects specific for monitor interfaces.  A
monitor interface is used for monitoring data on another
interface.  It outputs the same data as the in- or output of
the interface that it is monitoring.
          
The table is indexed using the same index as the itsIfTable.

itsIfMonEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.9.1

One monitor port is represented by one conceptual row in the
table. The interface is also represented in the itsIfTable
using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfMonMonitoredInterface The relative number of the interface on the board that this interface is selected to monitor. The first interface on the board is number 1, the second is number 2 and so on. A value of 0 denotes that no interface shal…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.9.1.1
itsIfMonDirection The direction of the monitored interface. in(1). Monitors the input data of the monitored interface. out(2). Monitors the output data of the monitored interface.	Enumerationr/w Enumerated Values: 1 in 2 out	.1.3.6.1.4.1.2928.6.2.16.1.1.9.1.2
itsIfEnableButton Controls if a `monitor' push button on the device front panel is enabled for selection of interface to monitor. This object is only applicable for boards supporting this function.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.9.1.3

Table with JPEG 2000 interfaces.  The table contains
configuration objects specific for JPEG 2000 encoding and
decoding capable interfaces, i.e. when any of the bits
`j2kEnc' or `j2kDec' are set in `itsIfCapabilities'.
          
The table is indexed using the same index as the itsIfTable.

itsIfJ2kEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.10.1

One JPEG 2000 capable interface is represented by one
conceptual row in the table. The interface is also
represented in the itsIfTable using the same index.

Indexes

itsIfIndex

Column	Syntax	OID
itsIfJ2kEncoderEnable Selects whether the JPEG 2000 encoder functionality is enabled of not for the interface. The rate of the JPEG 2000 stream is calculated from the channel capacity set in the channel manager (NETI-CHMGR-MIB). This objec…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.1
itsIfJ2kDecoderActive Indicates whether the JPEG 2000 decoder functionality is active or not. The interface acting as JPEG 2000 decoder is automatic. Only an egress interface can act as decoder.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.2
itsIfJ2kSignalFormat Indicates for which format JPEG 2000 is configured. The choice of format affects the available VBI configuration, the number of audio groups, and the configurable bandwidth range. notApplicable(0). If the…	Enumerationr/w Enumerated Values: 0 notApplicable 1 sdSdi 3 hdSdiEu 4 hdSdiUs 5 hd3gSdiEu 6 hd3gSdiUs	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.3
itsIfJ2kRateVideo The actual JPEG 2000 code stream bit rate. Applicable for both encoder and decoder interfaces.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.4
itsIfJ2kRateVideoMax The maximum JPEG 2000 code stream bit rate, calculated from the channel capacity, ANC, audio and VBI configurations.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.5
itsIfJ2kRateVbi The VBI service bit rate detected and forwarded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.6
itsIfJ2kRateAnc The ancillary data bit rate detected and forwarded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.7
itsIfJ2kRateAudio The audio bit rate detected and forwarded.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.8
itsIfJ2kAudioSampleSize The number of bits used for the audio samples: default 20-bit audio or extended 24-bit audio. This value is applicable only for SD-SDI signal format (PAL/NTSC), and only on source interfaces. The value zero (0) indica…	Unsigned32r/w Constraints: range: 0-0 range: 20-20 range: 24-24	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.9
itsIfJ2kReduceAudioTransportBitrate Enables or disables enhanced audio transport, using a reduced transport bitrate for the audio. This is only applicable for HD and 3G format, and only when the JPEG 2000 encodes is enabled (`itsIfJ2KEncodedEnable').	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.10.1.10

Table with audio groups.  The table contains configuration
objects specific for audio groups in SDI streams.  Each audio
group consists of 4 audio channels.  Audio group 5-8 is
available only for 3G-SDI.  The table is indexed per
interface and per audio group.

itsIfSdiAudioEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.11.1

One audio group is represented by one conceptual row in the
table. An entry may only exist for an interface that is
capable of JPEG 2000, i.e. when any of the bits `j2kEnc' or
`j2kDec' are set in `itsIfCapabilities'. T…

Indexes

itsIfIndex itsIfSdiAudioIndex

Column	Syntax	OID
itsIfSdiAudioIndex Index in the table. The index specifies the audio group number. Index 5-8 is only available for 3G-SDI.	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.2928.6.2.16.1.1.11.1.1
itsIfSdiAudioForward Indicates whether the audio group is enabled for transmission or not. Only applicable for source end interfaces.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.11.1.2

Table with Vertical Blanking Interval (VBI); lines outside
the actual picture that are used to forward data.  The number
of lines in the VBI depends on the format of the SDI signal.
VBI is only used in SD signals (PAL/NTSC).

itsIfSdiVbiEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.12.1

One entry per VBI line. An entry may only exist for an
interface that is capable of JPEG 2000, i.e. when any of the
bits `j2kEnc' or `j2kDec' are set in `itsIfCapabilities'.
The data is valid only if the interface is e…

Indexes

itsIfIndex itsIfSdiVbiIndex

Column	Syntax	OID
itsIfSdiVbiIndex The index in the table for the VBI line. This is not the same as the line number.	Integer32 Constraints: range: 1-46	.1.3.6.1.4.1.2928.6.2.16.1.1.12.1.1
itsIfSdiVbiLineNumber The line number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.12.1.2
itsIfSdiVbiForward Indicates whether the VBI line number is enabled for forwarding or not. The value is applicable only for source interfaces.	Enumerationr/w Enumerated Values: 0 notApplicable 1 yes 2 no	.1.3.6.1.4.1.2928.6.2.16.1.1.12.1.3

Table with ancillary data.  This is embedded into the SDI
signal but is not video.

itsIfSdiAncEntry row .1.3.6.1.4.1.2928.6.2.16.1.1.13.1

One DID/SDID combination is represented by one conceptual row
in the table. An entry may only exist for an interface that
is capable of JPEG 2000, i.e. when any of the bits `j2kEnc'
or `j2kDec' are set in `itsIfCapabil…

Indexes

itsIfIndex itsIfSdiAncIndex

Column	Syntax	OID
itsIfSdiAncIndex An index in the table, with one row per DID/SDID combination.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.2928.6.2.16.1.1.13.1.1
itsIfSdiAncDescription A string that identifies or describes the service corresponding to the DID/SDID combination.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.1.13.1.2
itsIfSdiAncDid The Data ID. Identifies the type of ANC. If the value is less than 0x08 then the ancillary data is of type 2, which means that the SDID is also present and should be used.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.13.1.3
itsIfSdiAncSdid The Secondary Data ID. This has the value of 0 if the ancillary data is of type 1.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.13.1.4
itsIfSdiAncForward Indicates if the DID/SDID combination is enabled for forwarding or not. The value is applicable only for source interfaces.	Enumerationr/w Enumerated Values: 0 notApplicable 1 yes 2 no	.1.3.6.1.4.1.2928.6.2.16.1.1.13.1.5

Table with settings for hitless 1+1 protection.

itsIfPs3Entry row .1.3.6.1.4.1.2928.6.2.16.1.1.14.1

One interface that is capable of hitless 1+1 protection is
represented by one row in this table. An entry may only
exist for an interface that is capable of switch type 3,
i.e. when the bits `hitps' or `psType3' is se…

Indexes

itsIfIndex

Column	Syntax	OID
itsIfPs3DifferentialDelay Measured differential delay in microseconds between the two paths. Zero (0) indicates that standby protection is used.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.1
itsIfPs3DifferentialDelayValid Specifies if the value of itsIfPs3DifferentialDelay is valid or not.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.2
itsIfPs3AheadInterface The index of the sink trail termination point (TTP) that is ahead. Minus one indicates either that information is not available or is invalid.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.3
itsIfPs3HitlessProtection Specifies if hitless protection shall be attempted or not. true(1). Will attempt to reach a hitless protection state. false(2). Will only attempt to reach a standby protection state.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.4
itsIfPs3ProtectionStatus The current protection state.	ItsProtectionStatus Type Values: 1 unavailable 2 unprotected 3 standbyProtected 4 hitlessCapable 5 hitlessProtected	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.5
itsIfPs3ExpectedProtectionStatus The expected protection state. When the current protection state (see itsIfPs3ProtectionStatus) is lower than the expected protection state, an alarm is raised. The alarm is cleared when the expected protection state …	ItsProtectionStatusr/w Type Values: 1 unavailable 2 unprotected 3 standbyProtected 4 hitlessCapable 5 hitlessProtected	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.6
itsIfPs3ForceHit A write of zero (0) resets the buffers, and will therefore minimize the the latency penalty incurred by the 1+1 buffering.	Unsigned32r/w Constraints: range: 0-0	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.7
itsIfPs3ActiveInterface The index of the sink trail termination point (TTP) that is is selected as source. Minus one indicates either that information is not available or is invalid.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.8
itsIfPs3MaxExpDifferentialDelay Maximum expected differential delay in milliseconds where 0 (zero) implies largest possible value for channel capacity and service type. If measured differential delay is above this, hitless protected status can not be…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.1.14.1.9

Table with source trail termination points.

itsSrcTtpEntry row .1.3.6.1.4.1.2928.6.2.16.1.2.3.1

One conceptual row represents one source trail termination point.

Indexes

itsSrcTtpIndex

Column	Syntax	OID
itsSrcTtpIndex The index in the table. The index is persistent cross reboots.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.1
itsSrcTtpName The textual name of the trail termination point (TTP). The value of this object should be the name of the TTP as assigned by the local device and should be suitable for use in commands entered at the device's console. T…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.2
itsSrcTtpCustomerId A customer identification number that represents the customer or user of the trail termination point (TTP). The value could be used e.g. for identifying the customer in Charge Data Records. The value zero (0) represents…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.3
itsSrcTtpPurpose A string describing the purpose of the TTP. The string is for administrative use.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.4
itsSrcTtpLocalIf A reference to the local interface that shall be used by the trail termination point (TTP). The value is representing the index in the itsIfTable. The value must refers to an existing entry in itsIfTable. When a TTP is …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.5
itsSrcTtpLocalDsti The DSTI (DTM Service Type Instance) for the source trail termination point. The value is used by the connection to refer to this trail termination point. The DSTI must be unique among the ITS source trail termination p…	NETI-CHMGR-MIBDstir/w Type Constraints: range: 0..32769	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.6
itsSrcTtpMode The TTP mode. The associated interface, itsSrcTtpLocalIf, must have the capability to support the property when the administrative state of the TTP is set to up. unicast(1). The trail termination point sh…	Enumerationr/w Enumerated Values: 1 unicast 2 multicast 3 compatible	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.7
itsSrcTtpODescription A reference to the corresponding description of the connection in the chmgrODescriptionTable in the Channel Manager MIB (NETI-CHMGR-MIB). The value is the index into the table, i.e. the value of chmgrODescrIndex. When a…	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.8
itsSrcTtpOConnection A reference to the corresponding originating connection in the table chmgrOConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). When an originating connection is established from this trail termination point, an…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.9
itsSrcTtpFailure A textual string describing a fault status on the trail termination point (TTP). A configuration error is regarded as a fault state, which is indicated when the administrative state is down. A network related fault can …	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.10
itsSrcTtpAdminStatus The administrative state of the connection. The value controls the desired state of the connection from the trail termination point (TTP). Note that the associated interface must have capabilities that matches the prope…	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.11
itsSrcTtpOperStatus The operational state of the trail termination point (TTP). up(1). The TTP is up and a connection is established to all destinations. If the connection is 1+1 protected, both the channels are established …	Enumeration Enumerated Values: 1 up 2 down 4 unknown 5 dormant 9 partial	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.12
itsSrcTtpRowStatus See SNMPv2-TC. Use itsSrcTtpAdminStatus to activate and de-activate a connection. The following values are supported: active(1). The object always reads active. createAndGo(4). A new concep…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2928.6.2.16.1.2.3.1.13

Table to lookup a DSTI to an index in the itsSrcTtpTable.

itsSrcIndexLookupEntry row .1.3.6.1.4.1.2928.6.2.16.1.2.4.1

One conceptual row represents one lookup entry.

Indexes

itsSrcTtpLocalDsti

Column	Syntax	OID
itsSrcIndexLookupIndex The value refers to the index in table itsSrcTtpTable.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.2.4.1.1

Table with sink trail termination points.

itsSnkTtpEntry row .1.3.6.1.4.1.2928.6.2.16.1.3.3.1

One conceptual row represents one sink trail termination point.

Indexes

itsSnkTtpIndex

Column	Syntax	OID
itsSnkTtpIndex The index in the table. The index is persistent across reboots.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.1
itsSnkTtpName The textual name of the trail termination point (TTP). The value of this object should be the name of the TTP as assigned by the local device and should be suitable for use in commands entered at the device's console. T…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.2
itsSnkTtpCustomerId A customer identification number that represents the customer or user of the trail termination point (TTP). The value could be used e.g. for identifying the customer in Charge Data Records. The value zero (0) represents…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.3
itsSnkTtpPurpose A string describing the purpose of the TTP. The object use is for administrative purpose.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.4
itsSnkTtpLocalIf A reference to the local interface that shall be used by the trail termination point (TTP). The value is representing the index in the itsIfTable. The value must point to an existing interface. When the TTP is created, …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.5
itsSnkTtpLocalDsti The DSTI (DTM Service Type Instance) for the sink trail termination point. The value is used by the connection to refer to this trail termination point. The DSTI must be unique among the ITS sink trail termination point…	NETI-CHMGR-MIBDstir/w Type Constraints: range: 0..32769	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.6
itsSnkTtpPSActiveChannel The channel to use on a 1+1 protected connection. When a connection is being established, the first established channel will become the active channel. The device will switch to the other channel when it detects a fault…	Enumerationr/w Enumerated Values: 1 primary 2 secondary 3 none	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.7
itsSnkTtpSuppressAlarm The alarm suppression mode. When alarms are suppressed, no alarms will be generated if a fault situation is detected on the trail termination point (TTP). Failures will still be shown by the object itsSnkTtpFailure. …	Enumerationr/w Enumerated Values: 0 notSupported 1 none 2 warning 3 all	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.8
itsSnkTtpTConnection A reference to the corresponding terminating connection in the table chmgrTConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB). The value is the index into that table, i.e. the value of chmgrTConnIndex. …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.9
itsSnkTtpDefects Defects indicated on the trail termination point since the last time the object was read. los(0) Loss of Signal was detected. lof(1) Loss of Frame was detected. ais(2). Alarm…	Bits Enumerated Values: 0 los 1 lof 2 ais 3 lop	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.10
itsSnkTtpFailure A textual string describing a fault status on the trail termination point (TTP). A configuration error is regarded as a fault state, which is indicated when the administrative state is down. A network related fault can …	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.11
itsSnkTtpPMReference A reference to an object that presents performance data for the trail termination point. The object is not part of this MIB. If the selected local interface (itsSnkLocalIf) does not support performance monitoring for th…	SNMPv2-TCRowPointer Description: Represents a pointer to a conceptual row. The value is the name of the instance of the first accessible columnar object in the conceptual row. For example, ifIndex.3 would point to the 3rd row in the ifTable…	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.12
itsSnkTtpAdminStatus The administrative state of the connection. The value controls the desired state of the connection from the trail termination point (TTP). up(1). The connection shall be active. down(2). Th…	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.13
itsSnkTtpOperStatus The operational state of the trail termination point (TTP). up(1). The TTP is up and a connection is established to all destinations. down(2). The connection is down to all destinations. …	Enumeration Enumerated Values: 1 up 2 down 5 dormant	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.14
itsSnkTtpRowStatus See SNMPv2-TC. Use itsSnkTtpAdminStatus to activate and de-activate a connection. The following values are supported: active(1). The object always reads active. createAndGo(4). A new concep…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.15
itsSnkTtpTConnection2 A reference to the corresponding terminating connection in the table chmgrTConnectionTable in the Channel Manager MIB (NETI-CHMGR-MIB) for the second established connection when 1+1 protection is used where the two chan…	Integer32 Constraints: range: -1-2147483647	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.16
itsSnkTtpPSAllow Controls if termination of an 1+1 is allowed: true(1). Allows termination of two channels or connections for a 1+1 protected service. false(2). Denies termination of a second channel or co…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2928.6.2.16.1.3.3.1.17

Table to lookup a DSTI to an index in the itsSnkTtpTable.

itsSnkIndexLookupEntry row .1.3.6.1.4.1.2928.6.2.16.1.3.4.1

One conceptual row represents one lookup entry.

Indexes

itsSnkTtpLocalDsti

Column	Syntax	OID
itsSnkIndexLookupIndex The value refers to the index in table itsSnkTtpTable.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2928.6.2.16.1.3.4.1.1