NETGEAR-RADLAN-rlInterfaces Table View

Index to the swIfTable. The interface defined by a
particular value of this index is the same interface as
identified by the same value of ifIndex (MIB II).

This variable indicates whether the physical address assigned to this
interface should be the default one or be chosen from the set of
reserved physical addresses of the device.

This variable specifies whether this interface should operate in
half duplex or full duplex mode. This specification will take effect
only if swIfSpeedDuplexAutoNegotiation is disabled.
A value of 'none' is returned if …

This variable indicates whether this interface operates in half
duplex or full duplex mode.
This variable can have the values hybrid or unknown
only for a trunk.
unknown - only if trunk operative status is not present.

This variable indicates whether this interface activates back pressure
when congested.

If enable, this interface operates in tagged mode, i.e all frames sent
out through this interface will have the 802.1Q header.
If disabled the frames will not be tagged.

This variable indicates the transceiver type of this interface.

This variable indicates whether this interface should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from this port and
forwards all frames arrived at this port. In locked mode …

This variable defines whether this interface operates in locked
or unlocked mode. It is locked in each of the following two cases:
1) if swLockAdminStatus is set to locked
2) no IP/IPX interface is defined over…

This variable specifies the type of interface.

This variable specifies the default VLAN tag which will be attached
to outgoing frames if swIfTaggedMode for this interface is enabled.

This variable specifies the default port priority.

The status of a table entry.
It is used to delete an entry from this table.

on - Flow control will be enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
autoNegotiation - Flow control will be enabled or disabled on this
interface. If en…

This variable specifies the required speed of this interface in bits
per second. This specification will take effect only if
swIfSpeedDuplexAutoNegotiation is disabled.
A value of 10 is returned for 10G.
A value of 0 is…

If enabled the speed and duplex mode will be set by the device through
the autonegotiation process. Otherwise these characteristics will be
set according to the values of swIfSpeedAdminMode and
swIfSpeedDuplexAutoNegoti…

on - Flow control is enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
enabledRx - Flow control is enabled on this interface for
recieved frames.
enabledTx - Flow co…

If enabled the speed and duplex are determined by the device through
the autonegotiation process.
If disabled these characteristics are determined according to the values
of swIfSpeedAdminMode and swIfDuplexAdminMode.
h…

This variable indicates the operative back pressure mode of
this interface.

This variable indicates which action this interface should be taken
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is f…

This variable indicates which action this interface actually takes in
locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is fo…

This variable indicates whether to create a SNMP trap in the locked mode.

This variable indicates whether a SNMP trap can be created in the
locked mode.

This variable indicates whether the port is suspended or not due to some
feature. After reboot this value is false

This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a
packet which was received on this ifIndex). It's relevant only in locked
mode while trap is …

This variable indicates the minimal frequency (in seconds) of sending
a trap per ifIndex. It's relevant only in locked mode and in trap
enabled.

This variable reactivates (enables) an ifIndex (which was suspended)

The configuration is on a physical port, not include trunks.
cross - The interface should force crossover.
normal - The interface should not force crossover.
auto - Auto mdix is enabled on the interface.

cross - The interface is in crossover mode.
normal - The interface is not in crossover mode.
unknown - Only for port that its operative status is not present
or down.

This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto.
In addtion multiple-auth was added.

This variable indicates which action this interface should take in single authorized.
Possible actions:
discard - every packet is dropped.
forwardNormal - every packet is forwarded according to the DST address.
discardD…

This variable indicates which action this interface actually takes in single authorized.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet is forwarded according to the DST address.…

This variable indicates whether to create a SNMP trap in single authorized.

This variable indicates whether a SNMP trap can be created in the single authorized.

This variable indicates the trap counter status per ifIndex
(i.e. number of received packets since the last trap sent due to a packet
which was received on this ifIndex). It's relevant only in single authorized
while tr…

This variable indicates the minimal frequency (in seconds) of sending a
trap per ifIndex. It's relevant only in single authorized and in trap enabled.
A value of 0 means that trap is disabled.

This variable indicates what is the learning limitation on the locked interface.
Possible values:
disabled - learning is stopped. The dynamic addresses associated with the
port are not aged out or relearned on other…

This variable defines the maximum number of dynamic addresses that
can be asscoiated with the locked interface. It isn't relevant in
disabled limitation mode.

This variable indicates the actual number of dynamic addresses that can
be asscoiated with the locked interface. It isn't relevant in disabled
limitation mode.

Administrative auto negotiation capabilities of the interface that can be advertised when
swIfSpeedDuplexAutoNegotiation is enabled.
default bit means advertise all the port's capabilities
according to its type.

Operative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up.

Operative auto negotiation capabilities of the remote link.
unknown bit means that port operative status is not up,
or auto negotiation process not complete,
or remote link is not auto negotiation able.

This variable specifies the administrative mode of a combo Ethernet interface.

This variable specifies the operative mode of a combo Ethernet interface.

This variable specifies the administrative mode of the Maste-Slave preference in auto negotiation.

Index to the swIfPortLockIfRangeTable.

The set of interfaces to which the port lock parameters should be configured

This variable indicates whether the interfaces range should operate in locked
or unlocked mode.
In unlocked mode the device learns all MAC addresses from these interfaces and
forwards all frames arrived at these interfa…

This variable indicates which action for these interfaces should be take
in locked mode and therefore relevant only in locked mode.
Possible actions:
discard(1) - every packet is dropped.
forwardNormal(2) - every packet…

This variable indicates whether to create a SNMP trap in the locked mode.

This variable indicates the minimal frequency (in seconds) of sending
a trap for these interfaces. It's relevant only in locked mode and in trap
enabled.

Configure speed of an SFP Ethernet interface.

Enable or disable cut-through for a priority for an interface.

Enable or disable cut-through for untagged packets for an interface.

Operational mode of spesific cut-through interface.