NEC-MIB Table View

Table which indicates the status of each part of the
equipment.

nodeStatusEntry row .1.3.6.1.4.1.119.2.3.14.9.1.2.1

Entry of the configuration of the table.

Indexes

nodeStatusIndex

Column	Syntax	OID
nodeStatusIndexmandatory Index of the system configuration of the equipment	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.1.2.1.1
nodeStatusPowermandatory Indicate the status of the Power Unit of the equipment.	Enumeration Enumerated Values: 1 normal 2 failure 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.1.2.1.2
nodeStatusSwitchModemandatory Indicate operational mode of SW-Engine of the equipment.	Enumeration Enumerated Values: 1 act 2 sby 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.1.2.1.3
nodeStatusSwitchmandatory Indicate the status of the SW-Engine of the equipment.	Enumeration Enumerated Values: 1 normal 2 failure 3 diagnostics 4 diagnosis-status-NG 5 initializing 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.1.2.1.4

Table which indicates the status of the PCMCIA card.
Every PCMCIA slot is provided with an entry.

nodePCMCIAEntry row .1.3.6.1.4.1.119.2.3.14.9.1.3.1

Entry of nodePCMCIATable

Indexes

nodeStatusIndex nodePCMCIAIndex

Column	Syntax	OID
nodePCMCIAIndexmandatory PCMCIA slot number per SW-Engine	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.119.2.3.14.9.1.3.1.1
nodePCMCIAStatusmandatory Status of PCMCIA card	Enumeration Enumerated Values: 1 normal 2 failure 3 initializing 4 busy 5 unknown 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.1.3.1.2
nodePCMCIATypemandatory Type of installed PCMCIA card	Enumeration Enumerated Values: 1 lan-card 2 ata-card 3 unknown 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.1.3.1.3

Table which indicates the line card configuration
of the equipment

slotIfConfEntry row .1.3.6.1.4.1.119.2.3.14.9.2.1.1

Entry of the line card configuration

Indexes

slotIfConfIndex

Column	Syntax	OID
slotIfConfIndexmandatory Index of line card configuration	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.1
slotIfConfPhysTypemandatory PMD layer/physical layer format of the line card. Above stated [oc3c], [oc12c] are ATM Form conformed names. They are corresponding to the ITU-T conformed names as follows: oc3c - STM1 oc12 - STM4 sts3c - STM1	Enumeration Enumerated Values: 1 other 2 taxi-100M 3 oc3c-SMF-Long 4 oc3c-SMF-Short 5 oc3c-MMF 6 relay-6Mcel 7 j2-6M-4M-3M 8 utp-5 9 oc12c-SMF-Type-A 10 oc12c-SMF-Type-B 11 ds3 12 e3 13 bts-1 14 bts-4 15 primary-1536K-1152K-768K-512K-384K-256K-192K 16 ds1 17 e1 18 oc3c-POF 19 sts3c-COAXIAL 50 vod-RxHFC4M 51 vod-TxHFC27M 52 svr 53 fr-ds1 54 fr-e1 55 dcs 56 ce-ds3 57 ce-ds1 58 ce-e1 59 ce-J2 60 svr2 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.2
slotIfConfRevmandatory The revision of the line cards. JpnToEng[?ѥå?????̤????????,0 length.]	RFC1213-MIBDisplayString	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.3
slotIfConfStatusmandatory Operational status of the line cards.	Enumeration Enumerated Values: 1 other 2 inService 3 outOfService 4 testing 5 initializing 6 installing 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.4
slotIfConfBufferTypemandatory The Buffer ID of the line cards.	Enumeration Enumerated Values: 1 other 2 ph1-buffer 3 ph2-buffer 4 fr-buffer 5 fr-buffer2 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.5
slotIfConfBufferRevmandatory The revision of the line card's buffers. JpnToEng[?ѥå?????̤????????,0 length.]	RFC1213-MIBDisplayString	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.6
slotIfConfResetmandatory Line card reset. The result of the reset order is indicated in slotIfConfResetResult. JpnToEng[PKG̤???????ʳ????ɤ߹??߻????ͤ?,???Ĥ? noOperation(1)?Ǥ???.]	Enumerationr/w Enumerated Values: 1 noOperation 2 reset 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.7
slotIfConfResetResultmandatory The current result of the reset order by slotIfConfReset.	Enumeration Enumerated Values: 1 succeed 2 other 3 diagnostics 4 unchangeableSlaveLine 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.2.1.1.8

Table related to the ATM specific lines which could not be
defined by MIB-II.
The table includes the configuration information,
operational status and error types of lines.

linfStatusEntry row .1.3.6.1.4.1.119.2.3.14.9.3.1.1

Entry of the line interface status indication.

Indexes

linfIndex

Column	Syntax	OID
linfIndexmandatory Index of the line interface status indication	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.1
linfStatusmandatory Status of the line interface or the receive clock	Enumeration Enumerated Values: 1 normal 2 los 3 lof 4 loc 5 ais-path 6 ais-section 7 yellow-section 8 yellow-path 9 lop 10 ais 11 payload-all-one 12 rai 13 oof 14 idle 15 rdi 16 plcp-oof 17 plcp-lof 18 plcp-yellow 19 red 80 loss-of-64K-clock 81 loss-of-8K-clock 82 frequency-out-of-range 97 failure 98 administratively-down 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.2
linfLoopBackmandatory Loop back status	Enumerationr/w Enumerated Values: 1 others 2 normal 3 localLoopBack 4 remoteLoopBack 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.3
linfConfmandatory Line card type.	Enumeration Enumerated Values: 1 others 2 private-UNI 3 private-NNI 4 public-UNI 6 uni 7 nni 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.4
linfFwdAvailableBandWidthmandatory Forward Available BandWidth(Mbps). JpnToEng[PKG̤????????,0]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.5
linfBkwdAvailableBandWidthmandatory Backward Available BandWidth(Mbps). JpnToEng[PKG̤????????,0]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.6
linfJ2Ratemandatory Indicate the line rate of the J2-dedicated line service.	Enumeration Enumerated Values: 1 not-leased-line 2 type-3-Mbps 3 type-4point5-Mbps 4 type-6point3-Mbps 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.7
linfCacFactormandatory JpnToEng(???Ԥ???7??ʬ)	Integer32r/w Constraints: range: 0-0 range: 10-1000	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.8
linfLoopBackCausemandatory JpnToEng[ʪ???롼?ץХå?????????.]	Enumeration Enumerated Values: 1 succeed 2 diagnosis 3 failure 4 notSupportedByPkg 5 alreadyRegistered 6 adminDown 7 initializing 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.9
linfBandWidthmandatory BandWidth[cell/s].JpnToEng[̵???ޤ???PKG̤?????????? 0.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.10
linfRecommendationmandatory JpnToEng[?б?????]	Enumeration Enumerated Values: 1 other 2 atmForum 3 itu 4 ttc 5 frameRelayForum 6 itu-t 7 ansi 8 fourVendor 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.11
linfUnassignedIdlemandatory Unassigned/Idle	Enumeration Enumerated Values: 1 notApplicable 2 unAssigned 3 idle 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.12
linfMaxActiveVpiBitsmandatory The length of valid VPI bits.JpnToEng[PKG̤????????0.]	Integer32 Constraints: range: 0-12	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.13
linfMaxActiveVciBitsmandatory The length of valid VCI bits.JpnToEng[PKG̤????????0.]	Integer32 Constraints: range: 0-14	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.14
linfPhysTypemandatory JpnToEng[???β?????°???륹???åȤ? slotIfConfPhysType ??]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.15
linfParam1mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.16
linfParam2mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.17
linfParam3mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.18
linfParam4mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.19
linfParam5mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.20
linfParam6mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.21
linfParam7mandatory JpnToEng(???Σ???ʬ)	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.1.1.22

Indicate status of FIFO on the shaper-line card.
* JpnToEng[SCR, MBS???ά?????Ȥ???CBR?Ȥߤʤ?,
 PCR?????�˥??????ԥ�졼?Ȥ??????Ԥʤ?.]
               
* Relationship between PCR, SCR and MBS value.
	PCR >= SCR
	PCR >= MBS

linfFifoConfEntry row .1.3.6.1.4.1.119.2.3.14.9.3.2.1

Entry of FIFO status indication

Indexes

linfFifoConfifIndex linfFifoConfIndex

Column	Syntax	OID
linfFifoConfifIndexmandatory Line Interface Index	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.1
linfFifoConfIndexmandatory Index of FIFO	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.2
linfFifoConfStatusmandatory Status of FIFO	Enumeration Enumerated Values: 1 normal 2 overflow	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.3
linfFifoConfPeekRatemandatory Peak Cell rate (PCR) for shaper-line card.	Integer32 Constraints: range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.4
linfFifoConfSustainRatemandatory Sustainable Cell Rate ( SCR) for shaper-line card.	Integer32 Constraints: range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.5
linfFifoConfMaxBurstSizemandatory Maximum Burst Size (MBS) for the shaper-line card.	Integer32 Constraints: range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.6
linfFifoConfRowStatusmandatory This object is used to designate the setting method for the shaping rate from the manager. Also, this object returns the reply to the shaping rate setting request from the agent side. - 'activ…	Enumeration Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.3.2.1.7

JpnToEng(???Σ???ʬ??)

connPvcEntry row .1.3.6.1.4.1.119.2.3.14.9.4.1.2.1

Entry of connPvcTable.
e.g.
receive +----------------------------------+transmit
=======>| ---- uni-directional-VCC ---- |=======>
(1/0/32)| |(2/0/32)
=======>| ---- bi-directional-…

Indexes

connPvcPort connPvcVpi connPvcVci connPvcDirection connPvcIndex

Column	Syntax	OID
connPvcPortmandatory Line port number	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.1
connPvcVpimandatory VPI number	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.2
connPvcVcimandatory VCI number	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.3
connPvcDirectionmandatory Indicate cell flow.	Enumeration Enumerated Values: 1 in 2 out 3 in-out 4 multi-out 5 multi-in	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.4
connPvcIndexmandatory JpnToEng[?????å??�??륨??ɥݥ???Ȥ? ???̤??륤??ǥå???.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.5
connPvcContrastPortmandatory JpnToEng[?????å??�??륨??ɥݥ???Ȥβ????ֹ?.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.6
connPvcContrastVpimandatory JpnToEng[?????å??�??륨??ɥݥ???Ȥ?VPI?ֹ?.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.7
connPvcContrastVcimandatory JpnToEng[?????å??�??륨??ɥݥ???Ȥ?VCI?ֹ?.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.8
connPvcTopologymandatory Topology of the Connection.	Enumeration Enumerated Values: 1 uni-directional-VCC 2 bi-directional-VCC 3 uni-directional-VPC 4 bi-directional-VPC 5 broadcast-VPC 6 broadcast-VCC 7 gateway	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.9
connPvcTrafficTypemandatory Traffic Type.	Enumeration Enumerated Values: 1 traffic-CBR 2 traffic-rt-VBR 3 traffic-nrt-VBR 4 traffic-ABR 5 traffic-UBR	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.10
connPvcFifoIndexmandatory The Shaper numbers of the direction from this endpoint to the endpoint to be switched. Value 0 means that Shaping will not be performed.	Integer32 Constraints: range: 0-16	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.11
connPvcContrastFifoIndexmandatory The Shaper number of the direction from the endpoint to be switched to this end point. Value 0 means that Shaping will not be performed.	Integer32 Constraints: range: 0-16	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.12
connPvcTrfConfmandatory Indicate Traffic control/status. If a path does not exist, noSuchName. 1. Indicate Traffic status 1) entry...registered 2) remove...not registered(initial status) 2. Register Traffic 1) Set connPvcTrfConf to '…	Enumerationr/w Enumerated Values: 1 entry 2 remove	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.13
connPvcTrfResultmandatory Indicate the processing result after Traffic control. If the path does not exist, noSuchName. The result of the registration EntrySucceed (2) --- Normal end of the registration AlreadyEntry (3) --- Double registrati…	Enumeration Enumerated Values: 1 other 2 entrySucceed 3 alreadyEntry 4 tableOverflow 5 removeSucceed 6 notEntry	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.14
connPvcParam1mandatory UPC mode of the direction from this endpoint to the endpoint to be switched. If nothing is designated, or the designation is invalid, off (1) is indicated.	Enumeration Enumerated Values: 1 off 2 mode1 3 mode2 4 mode3 5 mode4 6 mode5	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.15
connPvcContrastParam1mandatory UPC mode of the direction from the endpoint to be switched to this end point. If nothing is designated, or the designation is invalid, off (1) is indicated.	Enumeration Enumerated Values: 1 off 2 mode1 3 mode2 4 mode3 5 mode4 6 mode5	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.16
connPvcParam2mandatory Profile name of the direction from this endpoint to the endpoint to be switched. If nothing is designated, or the designation is invalid, the string of size(0) is indicated.	RFC1213-MIBDisplayString Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.17
connPvcContrastParam2mandatory Profile name of the direction from the endpoint to be switched to this end point. If nothing is designated, or the designation is invalid, the string of size(0) is indicated.	RFC1213-MIBDisplayString Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.18
connPvcParam3mandatory PCR[cell/s] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.19
connPvcContrastParam3mandatory PCR[cell/s] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.20
connPvcParam4mandatory SCR[cell/s] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.21
connPvcContrastParam4mandatory SCR[cell/s] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.22
connPvcParam5mandatory MBS[cell] of the direction from this endpoint to the endpoint to be switched. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.23
connPvcContrastParam5mandatory MBS[cell] of the direction from the endpoint to be switched to this end point. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.24
connPvcParam6mandatory EPD(Early Packet Discard) of the direction from this endpoint to the endpoint to be switched. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If t…	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.25
connPvcContrastParam6mandatory EPD(Early Packet Discard) of the direction from the endpoint to be switched to this end point. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If …	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.26
connPvcParam7mandatory MCR[cell/s]. Not supported here.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.27
connPvcContrastParam7mandatory MCR[cell/s]. Not supported here.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.1.2.1.28

Indicate traffic counter information per connection.

connPvcTrfEntry row .1.3.6.1.4.1.119.2.3.14.9.4.1.3.1

Entry of traffic per connection.
Every INDEX is equivalent to the one defined in connPvcEntry.

Indexes

connPvcPort connPvcVpi connPvcVci connPvcDirection connPvcIndex

Column	Syntax	OID
connPvcTrfInCellsmandatory The number of receive cells 64 bit counter	OctetString	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.1
connPvcTrfInCellsCountersmandatory The number of receive cells 32 bit counter	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.2
connPvcTrfOutCellsmandatory The number of transmit cells 64 bit counter	OctetString	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.3
connPvcTrfOutCellsCountersmandatory The number of transmit cells 32 bit counter	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.4
connPvcTrfInDropCellsmandatory The number of receive drop cells 64 bit counter	OctetString	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.5
connPvcTrfInDropCellsCountersmandatory The number of receive drop cells 32 bit counter	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.4.1.3.1.6

The table is used to show the information of current
established connections on the interface.

connConfIfEntry row .1.3.6.1.4.1.119.2.3.14.9.4.2.2.1

Entry of connConfIfTable.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
connConfIfPvcsmandatory The number of current established PVCs on the interface.	Integer32 Constraints: range: 0-16384	.1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.1
connConfIfSvcsmandatory The number of current established SVCs on the interface.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.2
connConfIfSoftPvcsmandatory The number of current established Soft PVPCs/PVCCs on the interface.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.119.2.3.14.9.4.2.2.1.3

This table is used to show the static routing table for SVC.

connRouteEntry row .1.3.6.1.4.1.119.2.3.14.9.4.3.2.1

Entry of connRouteTable.

Indexes

connRouteAtmAddressFormat connRouteAtmAddressLength connRouteAtmAddress

Column	Syntax	OID
connRouteTypemandatory The value of this object shows the routing type.	Enumeration Enumerated Values: 1 static 2 dynamic	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.1
connRoutePrimaryIfIndexmandatory	DstPrimaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.2
connRoutePrimaryVPImandatory	DstPrimaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.3
connRouteSecondaryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.4
connRouteSecondaryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.5
connRouteTertiaryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.6
connRouteTertiaryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.7
connRouteFourthryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.8
connRouteFourthryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.9
connRouteFifthryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.10
connRouteFifthryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.11
connRouteSixthryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.12
connRouteSixthryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.13
connRouteSeventhryIfIndexmandatory	DstSecondaryIfIndex Type Constraints: range: -1 range: 1..99	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.14
connRouteSeventhryVPImandatory	DstSecondaryVPI Type Constraints: range: -1..4095	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.15
connRoutePrimaryStatusmandatory Operational status of the primary routing. If the primary route of the routing table of the equipment is valid, enable(2), if not valid, disable(1).	Enumeration Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.16
connRoutePrimaryCausemandatory Cause of the switching from the primary route.	Enumeration Enumerated Values: 0 normal 1 other 2 outOfService 3 testing 4 lineInterface-Down 5 lineInterface-Failure 6 sw-Engine-Failure 7 sw-Engine-SwapOUT 99 notInstalled	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.17
connRouteAtmAddressFormatmandatory	DstAtmAddressFormat Type Values: -1 noWriting 1 e-164 2 nsap	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.18
connRouteAtmAddressLengthmandatory	DstAtmAddressLength Type Constraints: range: -1 range: 4..160	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.19
connRouteAtmAddressmandatory	DstAtmAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.119.2.3.14.9.4.3.2.1.20

This table include all entries to Soft-PVPC/PVCC 
currently available between the lines or the line and 
CPU port of the switch.  Also, this table is used to 
set or delete Soft-PVPC/PVCC.  The operable 
connection form between Soft-PVPC/PVCC is bi-
directional point-to-point only.
          
The procedure to set the connection is as follows:
          
1. Acquire connSoftPvcIndex
To set the connection, read connSoftPvcIndexNext and 
obtain an index of the Soft-PVPC/PVCC table.  The 
index must be managed by NMS. (The index is required 
to take an action to the connection.)
          
2. Set createAndWait
Set connSoftPvcRowStatus to CreateAndWait, using the 
obtained connSoftPvcIndex as index.  If the agent 
will set the parameter for the Soft-PVPC/PVCC 
setting to the default value and make 
connSoftRowStatus to notReady.
          
However, the same manager cannot create another row 
while creating a row (the status of the row is notRedy 
or notInService).
          
3. Get the default value
Get the default value of the object which serves as 
parameter for the connection setting. (The agent 
shall return -1 if it does not have a default value.)
          
Default values are as follows:
          
	connSoftPvcTopology		bi-directional-VCC(2)
	connSoftPvcTrafficType		traffic-UBR(5)
	connSoftPvcEndpointType		calling(1)
	connSoftPvcRetry		2
	connSoftPvcSrcAtmAddressFormat	nsap(2)
	connSoftPvcSrcAtmAddressLength	None
	connSoftPvcSrcAtmAddress	0 length string
	connSoftPvcSrcIfIndex		None
	connSoftPvcSrcVPI		None
	connSoftPvcSrcVCI		None
	connSoftPvcDstAtmAddressFormat	nsap(2)
	connSoftPvcDstAtmAddressLength	None
	connSoftPvcDstAtmAddress	0 length string
	connSoftPvcDstIfIndex		None
	connSoftPvcDstVPI		None
	connSoftPvcDstVCI		None
	connSoftPvcSrcFifoIndex		0
	connSoftPvcDstFifoIndex		0
	connSoftPvcNodeKind		model5(1)
	connSoftPvcSrcParam1		off(1)
	connSoftPvcDstParam1		off(1)
	connSoftPvcSrcParam2		0 length string
	connSoftPvcDstParam2		0 length string
	connSoftPvcSrcParam3		-1
	connSoftPvcDstParam3		-1
	connSoftPvcSrcParam4		-1
	connSoftPvcDstParam4		-1
	connSoftPvcSrcParam5		-1
	connSoftPvcDstParam5		-1
	connSoftPvcSrcParam6		off(2)
	connSoftPvcDstParam6		off(2)
	connSoftPvcSrcParam7		None (not installed)
	connSoftPvcDstParam7		None (not installed)
          
4. Set parameter
If a parameter does not have a default value, or the 
default value should not be used, set the parameter to 
a value.
If all parameters are set, the agent shall make 
connSoftPvcRowStatus to notInService.
          
5. Set active
By doing so, the agent checks parameters, resources and 
establishes the connection.
          
6. Get connSoftPvcRowStatus
If connSoftPvcRowStatus is active, the connection 
setting completed successfully, if notInService,the 
connection setting failed.  For the cause, refer to 
connSoftPvcCause.
(Note) When the connection setting has failed, if the 
connection is not released, the row will remain.
          
7. Get connSoftPvcRestRetry
Remaining counts of retry are contained.  If it is 
positive value, the retry is in progress.  If 
connSoftPvcRestRetry is 0, the retry completed.  The 
result of the connection setting should be seen, when 
this object is 0.
-1 means that infinite retry is in progress.
          
***Special pattern***
(1) If connSoftPvcTopology is bi-directional-VPC, set 
connSoftPvcSrcVCI, connSoftPvcDstVCI to 0.
          
The procedure to release the connection is as follows:
          
1. Set 'destroy'
Set connSoftPvcRowStatus to 'destroy', using 
connSoftPvcIndex of the connection to be deleted as 
index.
The agent will delete the connection, referring to 
it.
(Note) 'destroy' can also be set during the bypass 
processing.
          
2. Get the result
If the connection is deleted, 'get' of 
connSoftPvcTable of the designated index becomes 
NoSuchName.
          
The bypass processing of connection
          
1. Set notInService
When the agent executes the bypass processing of 
connection, set connSoftPvcRowStatus to 
notInService, and then establish the connection.
          
2. Get connSoftPvcRowStatus
If connSoftPvcRowStatus is 'active', the bypass 
connection setting has completed successfully.
If connSoftPvcRowStatus remains 'notInService', 
the connection setting has failed.
          
Others
          
1. The cut and recovery processing of connection is 
performed, following the delete and set procedures 
of the concerned connection.
Each procedure is as stated before.

connSoftPvcEntry row .1.3.6.1.4.1.119.2.3.14.9.4.5.1

Entry of ATMSoft-PVPC/PVCC connection

Indexes

connSoftPvcIndex

Column	Syntax	OID
connSoftPvcIndexmandatory The value of this object is equal to the connSoftPvcIndexNext. 1 - 128 : Soft PVPCs/PVCCs	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.1
connSoftPvcTopologymandatory Topology of the Connection.	Enumerationr/w Enumerated Values: 2 bi-directional-VCC 4 bi-directional-VPC	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.2
connSoftPvcTrafficTypemandatory Traffic Type.	Enumerationr/w Enumerated Values: 1 traffic-CBR 2 traffic-rt-VBR 3 traffic-nrt-VBR 4 traffic-ABR 5 traffic-UBR	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.3
connSoftPvcEndpointTypemandatory Type of Endpoint.	Enumeration Enumerated Values: 1 calling 2 called	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.4
connSoftPvcRetrymandatory Number of retry. 0 - 15 : Number of retry -1 : Infinite retry	Integer32r/w Constraints: range: -1-15	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.5
connSoftPvcSrcAtmAddressFormatmandatory AtmAdress format.	ConnSoftPvcSrcAtmAddressFormatr/w Type Values: -1 noWriting 1 e-164 2 nsap	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.6
connSoftPvcSrcAtmAddressLengthmandatory The valid bit length of connSoftPvcSrcAtmAddress. The value(-1) is read-only. The value(4..160) must be a multiple of 4.	Integer32r/w Constraints: range: -1--1 range: 4-160	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.7
connSoftPvcSrcAtmAddressmandatory NodeId of source node. Its maximum length is 13 bytes. This object length is 20 bytes in case AtmAddress is setting. If the last semi OCTET is invalid, it is padded with 0xf. The value of size(0) is read-only.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.8
connSoftPvcSrcIfIndexmandatory The number of the calling line. (ifIndex of ifEntry)	Integer32r/w Constraints: range: -1--1 range: 1-99	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.9
connSoftPvcSrcVPImandatory VPI value of the calling line.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.10
connSoftPvcSrcVCImandatory VCI value of the calling line.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.11
connSoftPvcDstAtmAddressFormatmandatory AtmAdress format.	ConnSoftPvcDstAtmAddressFormatr/w Type Values: -1 noWriting 1 e-164 2 nsap	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.12
connSoftPvcDstAtmAddressLengthmandatory The valid bit length of connSoftPvcDstAtmAddress. The value(-1) is read-only. The value(4..160) must be a multiple of 4.	Integer32r/w Constraints: range: -1--1 range: 4-160	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.13
connSoftPvcDstAtmAddressmandatory NodeId of destination node. Its maximum length is 13 bytes. This object length is 20 bytes in case AtmAddress is setting. If the last semi OCTET is invalid, it is padded with 0xf. The value of size(0) is read-only.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.14
connSoftPvcDstIfIndexmandatory The number of the called line. (ifIndex of ifEntry)65 is GateWay.	Integer32r/w Constraints: range: -1--1 range: 1-99	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.15
connSoftPvcDstVPImandatory VPI value of the called line.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.16
connSoftPvcDstVCImandatory VCI value of the called line.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.17
connSoftPvcRowStatusmandatory It is used from the manager to order the setting method of the Soft PVC connection. It is used from the agent side to return the result of the connection setting request. - 'active', which indicates …	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.18
connSoftPvcCausemandatory Object to indicate the result of the connection setting.	Enumeration Enumerated Values: 1 rowExisting 2 vpivciSrcBusy 3 vpivciDstBusy 4 vpivciOutOfRange 5 rateSrcOverFlow 6 rateDstOverFlow 7 dataTableFull 8 inconsistentVPVC 9 lineDiagnosis 10 missMatchTrfType 11 illegalSrcFileName 12 illegalDstFileName 13 lineOutOfOrder 14 illegalSrcShaper 15 illegalOperation 16 parameterIsNotEnough 17 diagnostics 18 otherFailure 19 illegalSrcRateForUPC 20 noCevc 21 noDlci 22 noSrcShaperForGateway 23 noPvcSrcShaperForGateway 24 missMatchTrfTypeSrcShaperForGateway 25 insusfficientPCRofProfile	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.19
connSoftPvcRestRetrymandatory Remaining number of retry 0 - 15 : Remaining number of retry -1 : Infinite retry in progress	Integer32 Constraints: range: -1-15	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.20
connSoftPvcSrcFifoIndexmandatory Designate the Shaper number of the calling line. If the Shaping is not performed, designate 0.	Integer32r/w Constraints: range: 0-16	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.21
connSoftPvcDstFifoIndexmandatory Designate the Shaper number of the called line. If the Shaping is not performed, designate 0. However, if the called sw is not furnished with the shaping function, this value has no meaning. Since it cannot be recogniz…	Integer32r/w Constraints: range: 0-16	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.22
connSoftPvcNodeKindmandatory Designate/indicate the machine type on the called side.	Enumerationr/w Enumerated Values: 1 model5 2 model7 3 model5E	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.23
connSoftPvcSrcParam1mandatory UPC mode of the calling line.	Enumerationr/w Enumerated Values: 1 off 2 mode1 3 mode2 4 mode3 5 mode4 6 mode5	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.24
connSoftPvcDstParam1mandatory UPC mode of the called line.	Enumerationr/w Enumerated Values: 1 off 2 mode1 3 mode2 4 mode3 5 mode4 6 mode5	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.25
connSoftPvcSrcParam2mandatory Profile name of Forward. If nothing is designated, the string of size(0) is designated.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.26
connSoftPvcDstParam2mandatory Profile name of Backward. If nothing is designated, the string of size(0) is designated.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.27
connSoftPvcSrcParam3mandatory PCR[cell/s] of Forward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.28
connSoftPvcDstParam3mandatory PCR[cell/s] of Backward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.29
connSoftPvcSrcParam4mandatory SCR[cell/s] of Forward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.30
connSoftPvcDstParam4mandatory SCR[cell/s] of Backward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.31
connSoftPvcSrcParam5mandatory MBS[cell] of Forward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.32
connSoftPvcDstParam5mandatory MBS[cell] of Backward. If the value is invalid, -1 is indicated.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.33
connSoftPvcSrcParam6mandatory EPD(Early Packet Discard) of Forward. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(2) is indicated.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.34
connSoftPvcDstParam6mandatory EPD(Early Packet Discard) of Backward. Indicate if the discard processing in the unit of AAL5 packet should be performed or not when the threshold is exceeded. If the value is invalid, off(2) is indicated.	Enumeration Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.35
connSoftPvcSrcParam7mandatory MCR[cell/s]. Not supported here.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.36
connSoftPvcDstParam7mandatory MCR[cell/s]. Not supported here.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.5.1.37

The table regarding the calling node of the Soft 
PVPC/PVCC established as called side office by the local node

connSoftPvcEstablishedSrcInfEntry row .1.3.6.1.4.1.119.2.3.14.9.4.6.1

The entry of the calling side node information of the
Soft PVPC/PVCC established as the called side office by
the local node

Indexes

connSoftPvcEstSrcInfIndex

Column	Syntax	OID
connSoftPvcEstablishedSrcInfmandatory The calling node information of the Soft PVPC/PVCC established as called side office by the node. The structure of the entry is as follows struct { long SrcAtmAddressFormat; long SrcAtmAddressLength; char S…	RFC1155-SMIOpaque	.1.3.6.1.4.1.119.2.3.14.9.4.6.1.1
connSoftPvcEstSrcInfIndexmandatory	ConnSoftPvcEstSrcInfIndex Type Constraints: range: 1..128	.1.3.6.1.4.1.119.2.3.14.9.4.6.1.2

OAM End-point, Connecting-point indication table

connOamEntry row .1.3.6.1.4.1.119.2.3.14.9.4.7.2.1

OAM End-point, Connecting-point indication entry

Indexes

connOamPort connOamIndex

Column	Syntax	OID
connOamPortmandatory Line number	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.1
connOamIndexmandatory OAM End-point / Connecting-point Index.	Integer32 Constraints: range: 1-144	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.2
connOamContrastPortmandatory Line number of the opposite line. For End-point, -1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.3
connOamVpimandatory VPI.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.4
connOamContrastVpimandatory Opposite VPI. For End-point, -1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.5
connOamVcimandatory VCI. For the f4 level, -1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.6
connOamContrastVcimandatory Opposite VCI. JpnToEng[End-point ?ޤ??? f4??٥?ξ??? -1.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.7
connOamPointmandatory End-point / Connecting-point.	Enumeration Enumerated Values: 1 end-point 2 connecting-point	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.8
connOamModemandatory Mode. F4 (VP level)/f5 (VC level).	Enumeration Enumerated Values: 1 f4 2 f5	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.9
connOamSectionmandatory Point between segments/End-to-End point.	Enumeration Enumerated Values: 1 segment 2 end-to-end	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.10
connOamStatusmandatory Receive status of end-point.	Enumeration Enumerated Values: 1 other 2 normal 3 receive-AIS 4 receive-RDI 5 failure	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.11
connOamDefectTypemandatory Fault cause in the receive cell. For Connecting-point, return 'normal (1)'.	Enumeration Enumerated Values: 1 normal 2 los 3 lof 4 loc 5 ais-path 6 ais-section 7 yellow-section 8 yellow-path 9 lop 10 ais 11 payload-all-one 12 rai 13 oof 14 idle 15 rdi 16 plcp-oof 17 plcp-lof 18 plcp-yellow 19 red	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.12
connOamDefectNodeIDmandatory Node ID of the Switch which sends alarm transfer cells. For connecting-point, return '0 length string'.	OctetString Constraints: range: 13-13	.1.3.6.1.4.1.119.2.3.14.9.4.7.2.1.13

Table to set/indicate the profile.

connProfileEntry row .1.3.6.1.4.1.119.2.3.14.9.4.9.2.1

Entry of connProfileTable.

Indexes

connProfileIndex

Column	Syntax	OID
connProfileIndexmandatory Index value of connProfileTable.	ConnProfileIndex	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.1
connProfileRowStatusmandatory Used to control rows of the table.	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.2
connProfileCausemandatory The result of Profile setting processing.	Enumeration Enumerated Values: 1 rowExisting 2 otherFailure 3 inconsistentEpd 4 parameterNotEnough 5 alreadyExist 6 duplicateName 7 inconsistentRate	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.3
connProfileTrafficTypemandatory Traffic Type.	Enumerationr/w Enumerated Values: 1 traffic-CBR 2 traffic-rt-VBR 3 traffic-nrt-VBR 4 traffic-ABR 5 traffic-UBR	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.4
connProfileNamemandatory Profile name. Available characters: alphanumeric characters 0 length string is only read.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.5
connProfileParam1mandatory For ph1/2-buffer, peek cell rate [cell/sec]. If it is invalid, -1. JpnToEng[ABR ?? -1 ?ξ???, ?Ӱ????/UPC??????�ʤ????Ȥ�?.]	Integer32r/w Constraints: range: -1--1 range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.6
connProfileParam2mandatory For ph1/2-buffer, Sustainable cell rate [cell/sec]. Only nrt-VBR, and rt-VBR are valid. If it is invalid, -1.	Integer32r/w Constraints: range: -1--1 range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.7
connProfileParam3mandatory For ph1/2-buffer, Maximum burst size [cell]. Only nrt-VBR, and rt-VBR are valid. If it is invalid, -1.	Integer32r/w Constraints: range: -1--1 range: 1-1412830	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.8
connProfileParam4mandatory For ph1/2-buffer, EPD function flag. If it is other than ABR, UBR, off, only.	Enumerationr/w Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.119.2.3.14.9.4.9.2.1.9

JpnToEng[?????֤????ꤵ??? SVC ????Υơ??֥?.]

connSvcEntry row .1.3.6.1.4.1.119.2.3.14.9.4.10.1

JpnToEng[?????֤????ꤵ??? SVC ????Υ???ȥ?.]

Indexes

RFC1213-MIBifIndex connSvcIndex

Column	Syntax	OID
connSvcIndexmandatory JpnToEng[SVC ????? Index.]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.10.1.1
connSvcInfmandatory JpnToEng(???Σ???????ʬ??) -- SVC ?ξ???. -- ????ȥ?ι?¤?ϰʲ????̤?. -- Bits -- 8 7 6 5 4 3 2 1 -- +-----+-----+-----+-----+-----+-----+-----+-----+ -- | ??Ǽ???…	RFC1155-SMIOpaque	.1.3.6.1.4.1.119.2.3.14.9.4.10.1.2

JpnToEng[CES?????ɤ????ꤵ?줿CEVC?ξ???ɽ????Ԥʤ?.]

connCeVcEntry row .1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1

JpnToEng[?????֤????ꤵ??????Ƥ?CEVC?Υ???ȥ꡼.]

Indexes

connCeVcPort connCeVcVci

Column	Syntax	OID
connCeVcPortmandatory Line number.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.1
connCeVcVcimandatory VCI value. JpnToEng[???Ѳ?ǽ?ϰ̤?linfStatusTable ????.]	Integer32 Constraints: range: 32-383	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.2
connCeVcRowStatusmandatory Used to control rows of the table.	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.3
connCeVcCausemandatory The result of CEVC setting processing.	Enumeration Enumerated Values: 1 rowExisting 2 otherFailure 3 parameterNotEnough 4 illegalpkg 5 vcsOverFllow 6 tssOverFllow 7 alreadyAssignedTs 8 inconsistentTss 9 illegalTimeslot 10 illegalPort 11 illegalVci 12 illegalUpPartialFillSize 13 illegalDownPartialFillSize 14 illegalCdvt	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.4
connCeVcDirectionmandatory JpnToEng[????????]	Enumerationr/w Enumerated Values: 1 bi 2 up 3 down	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.5
connCeVcUpPartialFillSizemandatory JpnToEng[UP?????Υ?????????????????줿ʿ?ѥ桼???????ƥåȿ? 0 ?ξ??? full ????(structure ?λ???46.875?ˤʤ?) 0 ?ʳ??κǾ??ͤ?,????TS??+1.]	Integer32r/w Constraints: range: -1-47	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.6
connCeVcDownPartialFillSizemandatory JpnToEng[DOWN?????Υ?????????????????줿ʿ?ѥ桼???????ƥåȿ? 0 ?ξ??? full ????(structure ?λ???46.875?ˤʤ?) 0 ?ʳ??κǾ??ͤ?,????TS??+1.]	Integer32r/w Constraints: range: -1-47	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.7
connCeVcConditionmandatory Condtion date.	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.8
connCeVcCDVTmandatory CDVT value. JpnToEng[pkg???̤ˤ??CDVT?ϰ?] +----------------------+----------+------------+ |pkg type| str mode |CDVT range| unit of | | | | | setting | ================================…	Integer32r/w Constraints: range: -1--1 range: 1-7218	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.9
connCeVcUpPCRmandatory JpnToEng[CEVC???????UP??????PCR??.]	Integer32 Constraints: range: -1-118979	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.10
connCeVcDownPCRmandatory JpnToEng[CEVC???????DOWN??????PCR??.]	Integer32 Constraints: range: -1-118979	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.11
connCeVcUpTimeSlot1mandatory JpnToEng(???Σ?????ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.12
connCeVcDownTimeSlot1mandatory JpnToEng(????2??ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.13
connCeVcUpTimeSlot2mandatory JpnToEng(????2??ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.14
connCeVcDownTimeSlot2mandatory JpnToEng(????2??ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.15
connCeVcUpTimeSlot3mandatory JpnToEng(????2??ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.16
connCeVcDownTimeSlot3mandatory JpnToEng(????2??ʬ)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.11.1.1.1.17

JpnToEng(????2??ʬ)

connFrDlciEntry row .1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1

Entry of connFrDlciTable.

Indexes

connFrDlciPort connFrDlciIndex

Column	Syntax	OID
connFrDlciPortmandatory Line number.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.1
connFrDlciIndexmandatory DLCI number.	Integer32 Constraints: range: 16-1007	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.2
connFrDlciRowStatusmandatory Used to control rows of the table.	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.3
connFrDlciCausemandatory JpnToEng[???ͥ??????(DLCI) ????ǡ??? ????????η??.]	Enumeration Enumerated Values: 1 rowExisting 2 otherFailure 3 noFrProfile 4 inconsistentInterWorking 5 totalCIROverFlow 6 lineDiagnosticsFailure 7 illegalPort 8 illegalDlci 9 pvcsOverFlow	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.4
connFrDlciFrProfilemandatory JpnToEng(????2??ʬ)	RFC1213-MIBDisplayStringr/w Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.5
connFrDlciPCRmandatory Peak Cell Rate[cell/sec]. JpnToEng[row??active?Ǥʤ??????ͤ? -1(?ǥե??????).]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.6
connFrDlciSCRmandatory Sustainable Cell Rate[cell/sec]. JpnToEng[row??active?Ǥʤ??????ͤ? -1(?ǥե??????).]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.7
connFrDlciMBSmandatory Maximum Burst Size[cell]. JpnToEng[row??active?Ǥʤ??????ͤ? -1(?ǥե??????).]	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.4.12.1.1.1.8

JpnToEng[Frprofile ?????? / ɽ????Ԥʤ?????Υơ??֥?.]

connFrProfileEntry row .1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1

Entry of connFrProfileTable.

Indexes

connFrProfileIndex

Column	Syntax	OID
connFrProfileIndexmandatory Index of connFrProfileTable.	ConnFrProfileIndex	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.1
connFrProfileRowStatusmandatory Used to control rows of the table.	Enumerationr/w Enumerated Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.2
connFrProfileCausemandatory The result of Frprofile setting processing.	Enumeration Enumerated Values: 1 rowExisting 2 otherFailure 3 parameterNotEnough 4 alreadyExist 5 duplicateName	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.3
connFrProfileNamemandatory Frprofile name. Available characters: alphanumeric characters 0 length string is only read.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-10	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.4
connFrProfileInterworkingTypemandatory Interworking Type	Enumerationr/w Enumerated Values: 1 network 2 service	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.5
connFrProfileCIRmandatory CIR value.	Integer32r/w Constraints: range: -1--1 range: 1-1984	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.6
connFrProfileDEtoCLPmandatory DE to CLP mapping mode	Enumerationr/w Enumerated Values: 1 mode1 2 mode2	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.7
connFrProfileCLPValuemandatory CLP Value. It's valid when connFrProfileDEtoCLP is mode2.	Enumerationr/w Enumerated Values: 1 notApplicable 2 on 3 off	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.8
connFrProfileCLPtoDEmandatory CLP to DE mapping mode.	Enumerationr/w Enumerated Values: 1 mode1 2 mode2	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.9
connFrProfileDEValuemandatory DE Value. It's valid when connFrProfileInterworkingType is service and connFrProfileCLPtoDE is mode2.	Enumerationr/w Enumerated Values: 1 notApplicable 2 on 3 off	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.10
connFrProfileCapsulationModemandatory Protocol encapsulation mode. It's valid when connFrProfileInterworkingType is service.	Enumerationr/w Enumerated Values: 1 notApplicable 2 transparent 3 translation	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.11
connFrProfileCongestionModemandatory Congestion indication(Forward) mode. It's valid when connFrProfileInterworkingType is service.	Enumerationr/w Enumerated Values: 1 notApplicable 2 mode1 3 mode2	.1.3.6.1.4.1.119.2.3.14.9.4.12.2.2.1.12

Table for showing the result of the performance monitoring 
per line of the equipment. Up to 64 tables are available for 
entry.
Every line whose traffic is managed per line is provided with 
an entry.

perfIfEntry row .1.3.6.1.4.1.119.2.3.14.9.5.2.1

Entry of the line performance monitoring.

Indexes

perfIfIndex

Column	Syntax	OID
perfIfIndexmandatory Line number.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.1
perfIfReceivedCellsmandatory The Number of the receive cells of line port. (64 bit applicable)	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.2
perfIfReceivedCellsCountersmandatory The Number of the receive cells of line port. (32 bit applicable).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.3
perfIfTransmittedCellsmandatory The Number of the transmit cells of line port. (64 bit applicable).	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.4
perfIfTransmittedCellsCountersmandatory The Number of the transmit cells of line port. (32 bit applicable).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.5
perfIfMisDelivdCellsmandatory The Number of the undefined cells of line port. (64 bit applicable).	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.8
perfIfMisDelivdCellsCountersmandatory The Number of the undefined cells of line port. (32 bit applicable).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.9
perfIfThresholdExcessCellsmandatory Number of the threshold excess cells (64 bit applicable).	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.10
perfIfThresholdExcessCellsCountersmandatory Number of the threshold excess cells (32 bit applicable).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.11
perfIfUpcErrorCellsmandatory Number of the UPC error cells (64 bit applicable).	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.12
perfIfUpcErrorCellsCountersmandatory Number of the UPC error cells (32 bit applicable).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.2.1.13

Table for showing the number of cells of the traffic and 
performance per line card of the equipment.
Up to 16 tables are available for entry.
Every line whose traffic is managed per slot is provided 
with an entry.
The object which becomes invalid by the line card is always 0.

perfIfSlotEntry row .1.3.6.1.4.1.119.2.3.14.9.5.3.1

Entry of traffic/performance per line card.

Indexes

slotIfConfIndex

Column	Syntax	OID
perfIfSlotReceivedCellsmandatory The number of receive cells.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.1
perfIfSlotTransmittedCellsmandatory The number of transmit cells.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.2
perfIfSlotInDropCellsmandatory The number of receive drop cells.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.3
perfIfSlotReceivedCellsCountersmandatory The number of receive cells.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.5
perfIfSlotTransmittedCellsCountersmandatory The number of transmit cells.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.6
perfIfSlotInDropCellsCountersmandatory The number of receive drop cells.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.7
perfIfSlotHCThresholdExcessCellsmandatory The number of threshold excess cells	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.9
perfIfSlotThresholdExcessCellsmandatory The number of threshold excess cells	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.10
perfIfSlotHCUpcErrorCellsmandatory Number of UPC error cells.	OctetString Constraints: range: 8-8	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.11
perfIfSlotUpcErrorCellsmandatory Number of UPC error cells.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.119.2.3.14.9.5.3.1.12

JpnToEng[ʪ???إѥե????ޥ�?˥??�??ơ??֥?.]

perfIfPhysEntry row .1.3.6.1.4.1.119.2.3.14.9.5.4.1

JpnToEng[ʪ???إѥե????ޥ�?˥??Υ???ȥ?.]

Indexes

perfIfPhysPort

Column	Syntax	OID
perfIfPhysPortmandatory Line number.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.1
perfIfPhysHCHecErorrsmandatory Number of HEC error cells(64 bit applicable). On the line card other than OC12, J2 and PR-1.5M, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.2
perfIfPhysHecErorrsmandatory Number of HEC error cells(32 bit applicable). On the line card other than OC12, J2 and PR-1.5M, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.3
perfIfPhysHCHecDropCellsmandatory Number of uncorrectable HEC error cells(64 bit applicable). On the line card other than OC3, OC12, OC12PMC, J2, PR-1.5, DS3, E3, DS1 and E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.4
perfIfPhysHecDropCellsmandatory Number of uncorrectable HEC error cells(32 bit applicable). On the line card other than OC3, OC12, OC12PMC, J2, PR-1.5, DS3, E3, DS1 and E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.5
perfIfPhysHCB1Errorsmandatory Number of B1 errors(64 bit applicable). On the line card other than OC3, OC12, OC12PMC, DS3, E3, DS1 and E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.6
perfIfPhysB1Errorsmandatory Number of B1 errors(32 bit applicable). On the line card other than OC3, OC12, OC12PMC, DS3, E3, DS1 and E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.7
perfIfPhysHCB2Errorsmandatory Number of B2 errors(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.8
perfIfPhysB2Errorsmandatory Number of B2 errors(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.9
perfIfPhysHCB3Errorsmandatory Number of B3 errors(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.10
perfIfPhysB3Errorsmandatory Number of B3 errors(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.11
perfIfPhysHCPathFEBEsmandatory Number of Path FEBEs(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.12
perfIfPhysPathFEBEsmandatory Number of Path FEBEs(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.13
perfIfPhysHCLineFEBEsmandatory Number of Line (Section) FEBEs(64 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.14
perfIfPhysLineFEBEsmandatory Number of Line (Section) FEBEs(32 bit applicable). On the line card other than OC3, OC12 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.15
perfIfPhysHCFramingErrorsmandatory Number of Framing errors(64 bit applicable). On the line card other than DS1, E1, DS3 and E3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.16
perfIfPhysFramingErrorsmandatory Number of Framing errors(32 bit applicable). On the line card other than DS1, E1, DS3 and E3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.17
perfIfPhysHCReceivedCellsmandatory The Number of the receive cells(64 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.18
perfIfPhysReceivedCellsmandatory The Number of the receive cells(32 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.19
perfIfPhysHCTransmittedCellsmandatory The Number of the transmit cells(64 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.20
perfIfPhysTransmittedCellsmandatory The Number of the transmit cells(32 bit applicable). On the line card other than DS3, E3 and OC12PMC, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.21
perfIfPhysHCIdelUnassignedCellsmandatory The Number of Idle/Unassigned cells(64 bit applicable). On the line card other than DS3 and E3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.22
perfIfPhysIdelUnassignedCellsmandatory The Number of Idle/Unassigned cells(32 bit applicable). On the line card other than DS3 and E3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.23
perfIfPhysHCFEBEErrorsmandatory Number of FEBE errors(64 bit applicable). On the line card other than DS3, E3, DS1 and E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.24
perfIfPhysFEBEErrorsmandatory Number of FEBEs errors(32 bit applicable). On the line card other than DS3, E3, DS1 and E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.25
perfIfPhysHCFEBEsmandatory Number of FEBEs(64 bit applicable). On the line card other than DS3, E3, E1 and CE-E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.26
perfIfPhysFEBEsmandatory Number of FEBEs(32 bit applicable). On the line card other than DS3, E3, E1 and CE-E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.27
perfIfPhysHCPathParityErrorsmandatory Number of path parity errors(64 bit applicable). On the line card other than DS3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.28
perfIfPhysPathParityErrorsmandatory Number of path parity errors(32 bit applicable). On the line card other than DS3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.29
perfIfPhysHCParityErrorsmandatory Number of parity errors(64 bit applicable). On the line card other than DS3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.30
perfIfPhysParityErrorsmandatory Number of parity errors(32 bit applicable). On the line card other than DS3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.31
perfIfPhysHCSEZsmandatory Number of detections of Summed excessive Zero (64 bit applicable). On the line card other than DS3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.32
perfIfPhysSEZsmandatory Number of detections of Summed excessive Zero (32 bit applicable). On the line card other than DS3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.33
perfIfPhysHCBitErrorsmandatory Number of Bit errors(64 bit applicable). On the line card other than DS3 and CE-DS1(SF mode), the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.34
perfIfPhysBitErrorsmandatory Number of Bit errors(32 bit applicable). On the line card other than DS3 and CE-DS1(SF mode), the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.35
perfIfPhysHCLcvErrorsmandatory Number of LCV errors(64 bit applicable). On the line card other than DS3, E3, DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.36
perfIfPhysLcvErrorsmandatory Number of LCV errors(32 bit applicable). On the line card other than DS3, E3, DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.37
perfIfPhysHCBip8Errorsmandatory Number of BIP-8 errors(64 bit applicable). On the line card other than E3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.38
perfIfPhysBip8Errorsmandatory Number of BIP-8 errors(32 bit applicable). On the line card other than E3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.39
perfIfPhysHCIecErrorsmandatory Number of IEC errors(64 bit applicable). On the line card other than E3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.40
perfIfPhysIecErrorsmandatory Number of IEC errors(32 bit applicable). On the line card other than E3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.41
perfIfPhysHCFramingPatternErrorsmandatory Number of Framing pattern errors(64 bit applicable). On the line card other than E3, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.42
perfIfPhysFramingPatternErrorsmandatory Number of Framing pattern errors(32 bit applicable). On the line card other than E3, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.43
perfIfPhysHCFramingBitErrorsmandatory Number of Framing bit errors(64 bit applicable). On the line card other than DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.44
perfIfPhysFramingBitErrorsmandatory Number of Framing bit errors(32 bit applicable). On the line card other than DS1, E1, FR-E1, CE-DS1, FR-DS1 and CE-E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.45
perfIfPhysHCCrcErrorsmandatory Number of CRC errors(64 bit applicable). On the line card other than DS1, E1, FR-E1, FR-DS1, CE-DS1(ESF mode) and CE-E1, the value of this object is 0.	OctetString	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.46
perfIfPhysCrcErrorsmandatory Number of CRC errors(32 bit applicable). On the line card other than DS1, E1, FR-E1, FR-DS1, CE-DS1(ESF mode) and CE-E1, the value of this object is 0.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.119.2.3.14.9.5.4.1.47