MX-R2-MIB Table View

R2 Channel Associated Signaling (R2 CAS)
          
Configuration parameters related to the R2 channel associated
signaling (R2 CAS) on this managed device.

r2Entry row .0.1875.1.100.100.1

A row in table R2 Channel Associated Signaling (R2 CAS).

Indexes

r2Name

Column	Syntax	OID
r2Name Name Name that identifies the interface.	OctetString	.0.1875.1.100.100.1.100
r2ChannelRange Channel Range Defines the range of active bearer channels.	OctetStringr/w Constraints: range: 1-10	.0.1875.1.100.100.1.200
r2ChannelAllocationStrategy Channel Allocation Strategy Defines the strategy for selecting bearer channels. Available strategies are: * Ascending: select the lowest-numbered non-busy bearer channel * Descendin…	Enumerationr/w Enumerated Values: 100 ascending 200 descending 300 roundRobinAscending 400 roundRobinDescending	.0.1875.1.100.100.1.300
r2MaxActiveCalls Maximum Active Calls Defines the maximum number of active calls on the interface. Note: The special value 0 indicates no maximum number of active calls.	Unsigned32r/w Constraints: range: 0-30	.0.1875.1.100.100.1.400
r2EncodingScheme Encoding Scheme Defines the voice encoding scheme in the bearer capabilities.This encoding scheme is used when initiating a call on the R2 side. The supported encoding schemes are G.711 u-Law and G.711 A-…	Enumerationr/w Enumerated Values: 100 g711alaw 200 g711ulaw	.0.1875.1.100.100.1.500
r2LineSignaling Line Signaling Defines the protocol to use for the line signaling: * Q421-2BitsSignaling: R2 line signaling type ITU-U Q.421. Typically used for PCM systems. This signa…	Enumerationr/w Enumerated Values: 100 q4212BitsSignaling	.0.1875.1.100.100.1.600
r2IncomingDigitSignaling Incoming Digit Signaling Defines the R2 incoming digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signalin…	Enumerationr/w Enumerated Values: 100 mfcR2 200 dtmfR2	.0.1875.1.100.100.1.750
r2OutgoingDigitSignaling Outgoing Digit Signaling Defines the R2 outgoing digit signaling method. * MfcR2: Multi Frequency Compelled - R2. * DtmfR2: Dual Tone Multi Frequency - R2. Digit signalin…	Enumerationr/w Enumerated Values: 100 mfcR2 200 dtmfR2	.0.1875.1.100.100.1.760
r2CountrySelection Country Selection Identifies the country. * Brazil-R2: Brazil R2 setting. * Mexico-R2: Mexico R2 setting. * Argentina-R2: Argentina R2 setting. * SaudiArabia-R2: SaudiArabia R2 sett…	Enumerationr/w Enumerated Values: 100 brazilR2 200 mexicoR2 300 argentinaR2 400 saudiArabiaR2 500 venezuelaR2 600 philippinesR2 700 iTUTR2	.0.1875.1.100.100.1.800
r2DigitAttenuation Digit Attenuation Additional attenuation in dB for MFR2/DTMF digit generation. By default, MFR2/DTMF digit generation power is determined by country selection. This parameter provides a mean to reduce thi…	Unsigned32r/w Constraints: range: 0-20	.0.1875.1.100.100.1.900

R2 Signaling Variants
          
This table allows to override or retrieve the default country
settings for R2 signaling parameters. This table is effective
only if the OverrideDefault parameter is Enabled. If the
OverrideDefault parameter is Disabled, any change in this
table have no effects.

r2SignalingVariantsEntry row .0.1875.1.100.200.1

A row in table R2 Signaling Variants.

Indexes

r2SignalingVariantsInterfaceName

Column	Syntax	OID
r2SignalingVariantsInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.100.200.1.100
r2SignalingVariantsOverrideDefault Override Default Overrides the default settings of R2 Signaling parameters for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration.…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.200.1.300
r2SignalingVariantsBitsCD CD Bits Settings of the C and D bits when the device transmits line signals. C and D bits of received line signals are ignored by the device.	Integer32r/w Constraints: range: 0-12	.0.1875.1.100.200.1.400
r2SignalingVariantsDnisLength DNIS Length This parameter specifies the expected length of the DNIS. DNIS (Dialed Number Identification Service) is the called party or the destination number. If a variable length is defined, then the I…	Unsigned32r/w Constraints: range: 0-20	.0.1875.1.100.200.1.500
r2SignalingVariantsAniLength ANI Length Defines the length of ANI (Automatic Number Identification) to be requested or sent. If a variable length ANI is used, the tone set in the R2ToneVariants.FwdGroup1EndOfAni parameter is sent to …	Unsigned32r/w Constraints: range: 0-20	.0.1875.1.100.200.1.600
r2SignalingVariantsAniRequestEnable ANI Request Enable Defines whether or not ANI should be requested. ANI (Automatic Number Identification) is the calling party number. When ANI is requested, the calling party category followed by the actu…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.200.1.700
r2SignalingVariantsSendAniRequestAfterDnisDigits Send ANI Request After DNIS Digits When the AniRequestEnable parameter is Enabled, this parameter defines the number of DNIS (Dialed Number Identification Service) digits to be received before sending the…	Unsigned32r/w Constraints: range: 0-10	.0.1875.1.100.200.1.800
r2SignalingVariantsCollectCallBlocked Collect Call Blocked Defines if the Collect Call Blockage Option is used. Two methods actually exist to do Collect Call Blockage. The first method refers to R2 signaling and how, through th…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.200.1.900
r2SignalingVariantsAniCategory Category Group II Signal Specifies the group II forward signal to be sent on receiving a calling party category request. This tone indicates the category of the calling party. * NatSubscr…	Enumerationr/w Enumerated Values: 100 natSubscriberNoPrio 200 natSubscriberPrio 300 natMaintenance 400 natSpare 500 natOperator 600 natData 700 intSubscriberNoPrio 800 intData 900 intSubscriberPrio 1000 intOperator 1100 collectCall	.0.1875.1.100.200.1.920
r2SignalingVariantsLineFreeCategory Line Free Group B signal Specifies the group B backward signal to be sent by the incoming R2 register to indicate line free condition of the destination party. * LineFreeCharge : Called p…	Enumerationr/w Enumerated Values: 100 lineFreeCharge 200 lineFreeNoCharge	.0.1875.1.100.200.1.930
r2SignalingVariantsAniRestrictedEnable ANI Restricted Enable This parameter specifies the behaviour of the unit following the reception of a reject request after sending the Send next digit (ANI) request. The request is generally rejected when…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.200.1.950
r2SignalingVariantsIncomingDeclineMethod Incoming Decline Method Sets how to cancel a call attempt from R2 if the called party rejects the call when in Seizure Acknowledged state (waiting for answer). * Release: B bit is set to …	Enumerationr/w Enumerated Values: 100 release 200 clearBack	.0.1875.1.100.200.1.970
r2SignalingVariantsResetSpecific Reset Specific Resets specific settings of R2 Signaling parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection paramet…	Enumerationr/w Enumerated Values: 0 noOp 10 resetSpecific	.0.1875.1.100.200.1.1000

R2 Signaling Timer Variants
          
This table allows to override or retrieve the default country
setting for R2 Timers.

r2TimerVariantsEntry row .0.1875.1.100.300.1

A row in table R2 Signaling Timer Variants.

Indexes

r2TimerVariantsInterfaceName

Column	Syntax	OID
r2TimerVariantsInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.100.300.1.100
r2TimerVariantsOverrideDefault Override Default Overrides the default setting of R2 Timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The configurat…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.300.1.300
r2TimerVariantsSeizureAckTimeout Seizure Ack Timeout Maximum time an outgoing R2 register waits for the seizure acknowledgement signal after sending a seizure signal. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.300.1.400
r2TimerVariantsFaultSeizureAckTimeout Fault Seizure Ack Timeout Maximum time an incoming R2 register waits for a seizure acknowledge failure condition to clear. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-100000	.0.1875.1.100.300.1.500
r2TimerVariantsDoubleSeizureTimeout Double Seizure Timeout Minimum time an outgoing R2 register waits after a double seizure is recognized before releasing the connection. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-1000	.0.1875.1.100.300.1.600
r2TimerVariantsDoubleAnswerTimeout Double Answer Timeout Maximum time an outgoing R2 register waits after receiving a clear-backward signal before releasing the connection. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-90000	.0.1875.1.100.300.1.700
r2TimerVariantsAnswerTimeout Answer Timeout Maximum time the answer signal AB=01 is applied before the clear backward signal AB=11 is sent. This parameter is generally used to reject collect calls (toll) and is only available if the …	Integer32r/w Constraints: range: 0-8000	.0.1875.1.100.300.1.710
r2TimerVariantsReAnswerTimeout ReAnswer Timeout Maximum time the clear backward signal AB=11 is applied before the answer signal AB=01 is reapplied again. This parameter is generally used to reject collect calls (toll) and is only avai…	Integer32r/w Constraints: range: 0-8000	.0.1875.1.100.300.1.720
r2TimerVariantsReleaseGuardTimeout Release Guard Timeout Maximum time an incoming R2 register waits after sending an idle line signal to prevent a new seizure of the line when a clear forward line signal is received. This va…	Integer32r/w Constraints: range: 0-4000	.0.1875.1.100.300.1.800
r2TimerVariantsInterCallGuardTimeout Inter-call Guard Timeout Maximum time an outgoing R2 register waits after receiving an idle line signal before attempting a new seizure of the line. This value is expressed in milliseconds …	Integer32r/w Constraints: range: 0-15000	.0.1875.1.100.300.1.820
r2TimerVariantsNoDigitTimeout No Digit Detected Timeout Maximum time an incoming R2 register waits before sending the congestion tone when no digits are received. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-120000	.0.1875.1.100.300.1.830
r2TimerVariantsCongestionToneGuardTimeout Congestion Tone Guard Timeout Maximum time an incoming R2 register waits after sending a congestion tone before sending a clear forward line signal and transits to the idle state. This valu…	Integer32r/w Constraints: range: 0-200000	.0.1875.1.100.300.1.850
r2TimerVariantsUnblockingTimeout Unblocking Timeout Maximum time a both-way trunk waits before assuming an idle state when a blocking condition is removed. This will prevent a too aggressive seizure of the trunk. This valu…	Integer32r/w Constraints: range: 0-4000	.0.1875.1.100.300.1.900
r2TimerVariantsAddressCompleteTimeout Address Complete Timeout The Address Complete Timeout is the maximum time that the caller waits for a reception of AddressComplete Tone after sending all ANI or DNIS Digits. This value is e…	Integer32r/w Constraints: range: 0-20000	.0.1875.1.100.300.1.1000
r2TimerVariantsWaitAnswerTimeout Wait Answer Timeout The maximal time that the caller waits for an Answer signal (ANSW) after receiving a Group B Line Free Signal Tone. This timer is effective only when the line is free. T…	Integer32r/w Constraints: range: 0-600000	.0.1875.1.100.300.1.1100
r2TimerVariantsDigitCompleteTimeout Digit Complete Timeout The maximal time that the caller waits for a Group I forward tone after sending either a Group A next Dnis digit, next Ani digit or next calling category Tone. This v…	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.300.1.1200
r2TimerVariantsWaitGroupBResponseCompleteTimeout Wait Group B Response Complete Timeout The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled sequ…	Integer32r/w Constraints: range: 0-30000	.0.1875.1.100.300.1.1300
r2TimerVariantsWaitImmediateResponseCompleteTimeout Wait Immediate Response Complete Timeout The maximal time that the caller waits for the confirmation of the end of the compelled sequence after receiving a Group B Signal Tone. The end of the compelled se…	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.300.1.1400
r2TimerVariantsPlayToneGuardTimeout Play Tone guard Timeout The maximum time an incoming R2 registers waits after receiving the confirmation of the reception of the Group B Signal Tone before playing one of the calling tones in the caller d…	Integer32r/w Constraints: range: 0-2000	.0.1875.1.100.300.1.1500
r2TimerVariantsAcceptCallTimeout Accept Call Timeout Time that the unit waits to accept a R2 CAS call. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.300.1.1600
r2TimerVariantsClearForwardGuardTimeout Clear Forward Guard Timeout The maximum time an outgoing R2 register waits after sending a clear forward line signal before transiting to the idle state. This value is expressed in millisec…	Integer32r/w Constraints: range: 0-600000	.0.1875.1.100.300.1.1700
r2TimerVariantsClearBackwardGuardTimeout Clear Backward Guard Timeout The maximum time an incoming R2 register waits after sending a clear backward line signal before sending the idle line signal and transit in the idle state. Thi…	Integer32r/w Constraints: range: 0-600000	.0.1875.1.100.300.1.1800
r2TimerVariantsFaultOnAnsweredGuardTimeout Fault On Answered Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the answer…	Integer32r/w Constraints: range: 0-86400000	.0.1875.1.100.300.1.1900
r2TimerVariantsFaultOnClearBackwardGuardTimeout Fault On Clear Backward Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the …	Integer32r/w Constraints: range: 0-86400000	.0.1875.1.100.300.1.2000
r2TimerVariantsFaultOnSeizeAckGuardTimeout Fault On Seize Ack Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize…	Integer32r/w Constraints: range: 0-86400000	.0.1875.1.100.300.1.2100
r2TimerVariantsFaultOnSeizeGuardTimeout Fault On Seize Guard Timeout The maximum time an outgoing R2 register waits for the fault to clear before sending the clear forward line signal. In the case of recognition of bb = 0 while in the seize sta…	Integer32r/w Constraints: range: 0-86400000	.0.1875.1.100.300.1.2200
r2TimerVariantsDeclineGuardTimeout Decline Guard Timeout Maximum time the AB=10 release signal is applied before sending the AB=11 clearback signal. This parameter applies when the IncomingDeclineMethod parameter is set to 'ClearBack' whil…	Integer32r/w Constraints: range: 1000-2000	.0.1875.1.100.300.1.2250
r2TimerVariantsResetSpecific Reset Specific Resets specific settings of R2 Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter.	Enumerationr/w Enumerated Values: 0 noOp 10 resetSpecific	.0.1875.1.100.300.1.2300

R2 Digit Timer Variants
          
This table allows to override or retrieve the default country
setting for R2 Digit Timers.

r2DigitTimerVariantsEntry row .0.1875.1.100.400.1

A row in table R2 Digit Timer Variants.

Indexes

r2DigitTimerVariantsInterfaceName

Column	Syntax	OID
r2DigitTimerVariantsInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.100.400.1.100
r2DigitTimerVariantsOverrideDefault Override Default Overrides the default setting of R2 Digit timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The conf…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.400.1.300
r2DigitTimerVariantsMfCongestionToneDuration MF Congestion Tone Duration Allows the administrator to specifically configures the duration of the transmission of the congestion tone. The special value '0' sets the duration according to the R2DigitTim…	Integer32r/w Constraints: range: 0-120000	.0.1875.1.100.400.1.350
r2DigitTimerVariantsMfcPulseInterDigitTimeout MFC Pulse Inter Digit Timeout The minimum delay between the end of transmission of the last signal of the compelled cycle and the start of the next one. This value is expressed in milliseco…	Integer32r/w Constraints: range: 0-1000	.0.1875.1.100.400.1.400
r2DigitTimerVariantsMfcPulseMinOnTimeout MFC Minimum Pulse OnTimeout The minimum time a backward tone can be on from the backward perspective. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-1000	.0.1875.1.100.400.1.500
r2DigitTimerVariantsMfcMaxSequenceTimeout MFC Maximum Sequence Timeout The maximum time for a complete compelled signaling cycle from the forward perspective. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-70000	.0.1875.1.100.400.1.600
r2DigitTimerVariantsMfcMaxOnTimeout MFC Maximum On Timeout The maximum time a forward tone can be on from the forward perspective. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-35000	.0.1875.1.100.400.1.700
r2DigitTimerVariantsMfcMaxOffTimeout MFC Maximum Off Timeout The maximum time a forward tone can be off from the forward perspective. This value is expressed in milliseconds (ms).	Integer32r/w Constraints: range: 0-35000	.0.1875.1.100.400.1.800
r2DigitTimerVariantsResetSpecific Reset Specific Resets specific settings of R2 Digit Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection para…	Enumerationr/w Enumerated Values: 0 noOp 10 resetSpecific	.0.1875.1.100.400.1.900

R2 Link Timer Variants
          
This table allows to override or retrieve the default country
setting for R2 Link Timers.

r2LinkTimerVariantsEntry row .0.1875.1.100.500.1

A row in table R2 Link Timer Variants.

Indexes

r2LinkTimerVariantsInterfaceName

Column	Syntax	OID
r2LinkTimerVariantsInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.100.500.1.100
r2LinkTimerVariantsOverrideDefault Override Default Overrides the default setting of R2 Link timers for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The confi…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.500.1.300
r2LinkTimerVariantsLinkActivationTimeout Link Activation Timeout The maximum time the unit waits for an activation indication coming from the physical link. The activation indication is used to indicate that the physical layer connection has bee…	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.500.1.400
r2LinkTimerVariantsLinkActivationRetryTimeout Link Activation Retry Timeout The maximum time the unit waits before attempting to reestablish the physical link. The attempt is made when the physical layer connection has been deactivated. …	Integer32r/w Constraints: range: 0-10000	.0.1875.1.100.500.1.500
r2LinkTimerVariantsResetSpecific Reset Specific Resets specific settings of R2 Link Timers parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection param…	Enumerationr/w Enumerated Values: 0 noOp 10 resetSpecific	.0.1875.1.100.500.1.600

R2 Signaling Tone Variants
          
This table allows to override or retrieve the default country
setting for R2 Tone variants in forward and backward group.

r2ToneVariantsEntry row .0.1875.1.100.600.1

A row in table R2 Signaling Tone Variants.

Indexes

r2ToneVariantsInterfaceName

Column	Syntax	OID
r2ToneVariantsInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.100.600.1.100
r2ToneVariantsOverrideDefault Override Default Overrides the default setting of R2 tone variants for the CountrySelection and InterfaceName. * Disable: The interface uses the default country configuration. The con…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.100.600.1.300
r2ToneVariantsFwdGroup1EndOfDnis Forward Group 1 EndOfDnis Tone Specifies the forward Group 1 tone used to send after the DNIS digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 i1 300 i2 400 i3 500 i4 600 i5 700 i6 800 i7 900 i8 1000 i9 1100 i10 1200 i11 1300 i12 1400 i13 1500 i14 1600 i15	.0.1875.1.100.600.1.400
r2ToneVariantsFwdGroup1EndOfAni Forward Group 1 EndOfAni Tone Specifies the forward Group 1 tone used to send after the ANI digits. * None: No tone used. * I1..I15: Group 1 forward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 i1 300 i2 400 i3 500 i4 600 i5 700 i6 800 i7 900 i8 1000 i9 1100 i10 1200 i11 1300 i12 1400 i13 1500 i14 1600 i15	.0.1875.1.100.600.1.500
r2ToneVariantsFwdGroup1RestrictedAni Forward Group 1 Restricted ANI Tone Specifies the forward Group 1 tone used to reject a send next digit (ANI). This tone is generally used in response to the identification request when the caller party i…	Enumerationr/w Enumerated Values: 100 none 200 i1 300 i2 400 i3 500 i4 600 i5 700 i6 800 i7 900 i8 1000 i9 1100 i10 1200 i11 1300 i12 1400 i13 1500 i14 1600 i15	.0.1875.1.100.600.1.520
r2ToneVariantsBwdGroupASendNextDnisDigit Backward Group A SendNextDnisDigit Tone Specifies the backward Group A tone used to request the next DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.600
r2ToneVariantsBwdGroupASendPreviousDnisDigit Backward Group A SendPreviousDnisDigit Tone Specifies the backward Group A tone used to request the previous DNIS digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.700
r2ToneVariantsBwdGroupASwitchToGroupII Backward Group A BwdGroupASwitchToGroupII Tone Specifies the backward Group A tone used to request to the caller a switch of Group II signals. * None: No tone used. * A1..A15: Group A b…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.800
r2ToneVariantsBwdGroupANetworkCongestion Backward Group A NetworkCongestion Tone Specifies the backward Group A tone to be sent when a congestion network is detected. * None: No tone used. * A1..A15: Group A backward signal MF…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.900
r2ToneVariantsBwdGroupASendCallingPartyCategory Backward Group A SendCallingPartyCategory Tone Specifies the backward Group A tone sent when the backward group requests the calling party category. * None: No tone used. * A1..A15: Gro…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1000
r2ToneVariantsBwdGroupAImmediateAccept Backward Group A ImmediateAccept Tone Specifies the backward Group A tone sent when the backward group accepts the call immediatly. * None: No tone used. * A1..A15: Group A backward sig…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1100
r2ToneVariantsBwdGroupASendDnisDigitNMinus2 Backward Group A BwdGroupASendDnisDigitNMinus2 Tone Specifies the backward Group A tone used to request the previous - 1 DNIS digit. * None: No tone used. * A1..A15: Group A backward si…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1200
r2ToneVariantsBwdGroupASendDnisDigitNMinus3 Backward Group A BwdGroupASendDnisDigitNMinus3 Tone Specifies the backward Group A tone used to request the previous - 2 DNIS digit. * None: No tone used. * A1..A15: Group A backward si…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1300
r2ToneVariantsBwdGroupARepeatAllDnis Backward Group A BwdGroupARepeatAllDnis Tone Specifies the backward Group A tone used to request all DNIS digits. * None: No tone used. * A1..A15: Group A backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1400
r2ToneVariantsBwdGroupASendNextAniDigit Backward Group A BwdGroupASendNextAniDigit Tone Specifies the backward Group A tone used to request the next ANI digit. * None: No tone used. * A1..A15: Group A backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1500
r2ToneVariantsBwdGroupASendCallingPartyCategorySwitchGroupC Backward Group A BwdGroupASendCallingPartyCategorySwitchGroupC Tone Specifies the backward Group A tone used to request the calling party category and then switch to Group C signals. * No…	Enumerationr/w Enumerated Values: 100 none 200 a1 300 a2 400 a3 500 a4 600 a5 700 a6 800 a7 900 a8 1000 a9 1100 a10 1200 a11 1300 a12 1400 a13 1500 a14 1600 a15	.0.1875.1.100.600.1.1550
r2ToneVariantsBwdGroupBSendSit Backward Group B BwdGroupBSendSpecialToneInformation Tone Specifies the backward Group B tone used to send a special information tone. * None: No tone used. * B1..B15: Group B backward …	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.1600
r2ToneVariantsBwdGroupBUserBusy Backward Group B BwdGroupBUserBusy Tone Specifies the backward Group B tone used to signal a user busy. * None: No tone used. * B1..B15: Group B backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.1700
r2ToneVariantsBwdGroupBNetworkCongestion Backward Group B BwdGroupBNetworkCongestion Tone Specifies the backward Group B tone used to signal a network congestion. * None: No tone used. * B1..B15: Group B backward signal MF Ton…	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.1800
r2ToneVariantsBwdGroupBUnassignedNumber Backward Group B BwdGroupBUnassignedNumber Tone Specifies the backward Group B tone used to signal an unassigned number. * None: No tone used. * B1..B15: Group B backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.1900
r2ToneVariantsBwdGroupBLineFreeCharge Backward Group B BwdGroupBLineFreeCharge Tone Specifies the backward Group B tone used to signal that the line is free and charge must be applied. * None: No tone used. * B1..B15: Group…	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.2000
r2ToneVariantsBwdGroupBSupplementaryLineFreeCharge Backward Group B BwdGroupBSupplementaryLineFreeCharge Tone Specifies a supplementary backward Group B tone used to detect that the line is free and charge must be applied. This is a supplementary (optionn…	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.2100
r2ToneVariantsBwdGroupBLineFreeNoCharge Backward Group B BwdGroupBLineFreeNoCharge Tone Specifies the backward Group B tone used to signal that the line is free and no charges must be applied. * None: No tone used. * B1..B15:…	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.2200
r2ToneVariantsBwdGroupBLineOutOfOrder Backward Group B BwdGroupBLineOutOfOrder Tone Specifies the backward Group B tone used to signal that the line is out of order. * None: No tone used. * B1..B15: Group B backward signal …	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.2300
r2ToneVariantsBwdGroupBChangedNumber Backward Group B BwdGroupBChangedNumber Tone Specifies the backward Group B tone used to signal that the subscriber has changed number. * None: No tone used. * B1..B15: Group B backward…	Enumerationr/w Enumerated Values: 100 none 200 b1 300 b2 400 b3 500 b4 600 b5 700 b6 800 b7 900 b8 1000 b9 1100 b10 1200 b11 1300 b12 1400 b13 1500 b14 1600 b15	.0.1875.1.100.600.1.2350
r2ToneVariantsBwdGroupCSendNextAniDigit Backward Group C BwdGroupCSendNextAniDigit Tone Specifies the backward Group C tone used to request the next ANI digit. * None: No tone used. * C1..C15: Group C backward signal MF Tones	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2355
r2ToneVariantsBwdGroupCRepeatAllDnisSwitchGroupA Backward Group C BwdCRepeatAllDnisSwitchGroupA Tone Specifies the backward Group C tone used to request all DNIS digits and then switch to Group A signals. * None: No tone used. * C1..C…	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2360
r2ToneVariantsBwdGroupCSendNextDnisDigitSwitchGroupA Backward Group C BwdCSendNextDnisDigitSwitchGroupA Tone Specifies the backward Group C tone used to request the next DNIS digit and then switch to Group A signals. * None: No tone used. …	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2365
r2ToneVariantsBwdGroupCNetworkCongestion Backward Group C BwdGroupCNetworkCongestion Tone Specifies the backward Group C tone used to signal a network congestion. * None: No tone used. * C1..C15: Group C backward signal MF Ton…	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2370
r2ToneVariantsBwdGroupCSendPreviousDnisDigitSwitchGroupA Backward Group C BwdCSendPreviousDnisDigitSwitchGroupA Tone Specifies the backward Group C tone used to request the previous DNIS digit and then switch to Group A signals. * None: No tone…	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2375
r2ToneVariantsBwdGroupCSwitchGroupII Backward Group C BwdCSwitchGroupII Tone Specifies the backward Group C tone used to request to the caller a switch of Group II signals. * None: No tone used. * C1..C15: Group C backward…	Enumerationr/w Enumerated Values: 100 none 200 c1 300 c2 400 c3 500 c4 600 c5 700 c6 800 c7 900 c8 1000 c9 1100 c10 1200 c11 1300 c12 1400 c13 1500 c14 1600 c15	.0.1875.1.100.600.1.2380
r2ToneVariantsResetSpecific Reset Specific Resets specific settings of R2 Tones parameters with the default country settings. This command is used to retrieve the default country configuration set in the CountrySelection parameter.	Enumerationr/w Enumerated Values: 0 noOp 10 resetSpecific	.0.1875.1.100.600.1.2400

Bearer Channel Info
          
Port-specific operational, statistics, and active call data
for B channels.

bearerChannelInfoEntry row .0.1875.1.200.100.1

A row in table Bearer Channel Info.

Indexes

bearerChannelInfoIndex

Column	Syntax	OID
bearerChannelInfoIndex Index Identifies the Bearer Channel..	OctetString	.0.1875.1.200.100.1.100
bearerChannelInfoState State The current call control state for this channel: * Idle: The channel is available * InUse: The channel is currently used * Maintenance: Maintenance state, temporarily unavailabl…	Enumeration Enumerated Values: 100 idle 200 inUse 300 maintenance 400 error 500 disabled	.0.1875.1.200.100.1.200

Physical Link Information
          
The physical link information table contains status
information for all interfaces on this managed device.

physicalLinkInfoEntry row .0.1875.1.300.100.1

A row in table Physical Link Information.

Indexes

physicalLinkInfoInterfaceName

Column	Syntax	OID
physicalLinkInfoInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.300.100.1.100
physicalLinkInfoState State The layer 1 state for this interface: * Up: Layer 1 connectivity. * Down: No layer 1 connectivity. The interface might be in this state because no cable is plugged in or a pin…	Enumeration Enumerated Values: 100 up 200 down	.0.1875.1.300.100.1.200

Physical Link
          
The physical link table containing configuration and
operational parameters for all interfaces on this managed
device.

physicalLinkEntry row .0.1875.1.300.200.1

A row in table Physical Link.

Indexes

physicalLinkInterfaceName

Column	Syntax	OID
physicalLinkInterfaceName Interface Name Identifies the interface.	OctetString	.0.1875.1.300.200.1.100
physicalLinkLineCoding Line Coding Defines the transmission encoding of bits: * B8ZS: Bipolar with 8-Zeros Substitution (T1 lines) * HDB3: High-Density Bipolar Order 3 (E1 lines) * AMI: Alternate Mark Inver…	Enumerationr/w Enumerated Values: 100 b8zs 200 hdb3 300 ami	.0.1875.1.300.200.1.200
physicalLinkLineFraming Line Framing Defines the frame format: * SF: Super frame. Sometimes known as D4 (T1 lines) * ESF: Extended super frame (T1 lines) * CRC4: Cyclic redundancy check 4 (E1 lines) * NO-C…	Enumerationr/w Enumerated Values: 100 sf 200 esf 300 crc4 400 noCrc4	.0.1875.1.300.200.1.300
physicalLinkClockMode Clock Mode A port can either generate the clocking for the line or accept the clock from the line. The options master or slave determine the clocking method: * Master: Generates clock *…	Enumerationr/w Enumerated Values: 100 master 200 slave	.0.1875.1.300.200.1.400
physicalLinkMonitorLinkStateEnable Monitor Link State Enable Monitors the physical link state of an R2 interface. Enable: An R2 endpoint's operational state is affected by its interface physical link state. When the link sta…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1875.1.300.200.1.500
physicalLinkPortPinout Port Pinout Defines the port pinout: * Auto: The pinout is set according to the clock mode. * Master: Force the pinout to Master regardless of the clock mode. * Slave: Force the p…	Enumerationr/w Enumerated Values: 100 auto 200 master 300 slave	.0.1875.1.300.200.1.600