MX-EAM-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
9
Rows
9
Columns
60

eamTable

table
.0.1880.1.100.100 · 1 row entry · 7 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamTable'
E&M Channel Associated Signaling
          
Configuration parameters related to the E&M channel associated
signaling on this managed device.
eamEntry row .0.1880.1.100.100.1
A row in table E&M Channel Associated Signaling.
Indexes
Column Syntax OID
eamNameName

Name that identifies the interface.
OctetString.0.1880.1.100.100.1.100
eamChannelRangeChannel Range

Defines the range of active bearer channels.
OctetStringr/w
Constraints:
range: 1-10
.0.1880.1.100.100.1.200
eamChannelAllocationStrategyChannel Allocation Strategy

Defines the strategy for selecting bearer channels. Available
strategies are:

* Ascending: select the lowest-numbered non-busy bearer
channel
* Descendin…
Enumerationr/w
Enumerated Values:
100ascending
200descending
300roundRobinAscending
400roundRobinDescending
.0.1880.1.100.100.1.300
eamMaxActiveCallsMaximum Active Calls

Defines the maximum number of active calls on the interface.

Note: The special value 0 indicates no maximum number of
active calls.
Unsigned32r/w
Constraints:
range: 0-30
.0.1880.1.100.100.1.400
eamEncodingSchemeEncoding Scheme

Defines the voice encoding scheme in the bearer capabilities.
Enumerationr/w
Enumerated Values:
100g711alaw
200g711ulaw
.0.1880.1.100.100.1.500
eamSignalingTypeSignaling Type

Identifies the E&M signaling type.

* E&M Wink start: Set configuration parameters for basic
Wink Start signaling. After setting SignalingType,
individual configurat…
Enumerationr/w
Enumerated Values:
100winkStart
200immediateStart
300fgb
400fgd
.0.1880.1.100.100.1.600
eamDigitAttenuationDigit Attenuation

Additional attenuation in dB for MFR1/DTMF digits generation.
By default, MFR1/DTMF digits generation power is determined
by variant selection. This parameter provides a mean to
reduce t…
Unsigned32r/w
Constraints:
range: 0-20
.0.1880.1.100.100.1.700
.0.1880.1.100.200 · 1 row entry · 14 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamSignalingVariantsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamSignalingVariantsTable'
E&M Signaling Variants
          
This table allows to override or retrieve the default
signaling settings for E&M signaling parameters. This table is
effective only if the OverrideDefault parameter is Enabled. If
the OverrideDefault parameter is Disabled, any change in this
table has no effects.
eamSignalingVariantsEntry row .0.1880.1.100.200.1
A row in table E&M Signaling Variants.
Column Syntax OID
eamSignalingVariantsInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.100.200.1.100
eamSignalingVariantsOverrideDefaultOverride Default

Overrides the default settings of E&M Signaling parameters
for the SignalingType and InterfaceName.

* Disable: The interface uses the default configuration
associated…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.200.1.200
eamSignalingVariantsBitsBCDBCD Bits

Settings of the B, C and D bits when the device transmits
line signals. B, C and D bits of received line signals are
ignored by the device.

BCD bits definition

* 0…
Integer32r/w
Constraints:
range: 0-8
.0.1880.1.100.200.1.300
eamSignalingVariantsDnisLengthDNIS Length

Defines the expected length of the DNIS. DNIS (Dialed Number
Identification Service) is the called party or the
destination number.

* 0: Variable DNIS length used.
* 1..20: …
Unsigned32r/w
Constraints:
range: 0-20
.0.1880.1.100.200.1.400
eamSignalingVariantsAniLengthANI Length

Defines the expected length of the ANI. ANI (Automatic Number
Identification) is the number of the calling party.

* 0 : Variable ANI length.
* 1..20 : Specific ANI length.
Unsigned32r/w
Constraints:
range: 0-20
.0.1880.1.100.200.1.500
eamSignalingVariantsIncomingRegisterSignalingIncoming Register Signaling

Defines the incoming register signaling method.

* MfR1: Multi Frequency - R1.
* Dtmf: Dual Tone Multi Frequency.
Enumerationr/w
Enumerated Values:
100mfR1
200dtmf
.0.1880.1.100.200.1.600
eamSignalingVariantsOutgoingRegisterSignalingOutgoing Register Signaling

Defines the outgoing register signaling method.

* MfR1: Multi Frequency - R1.
* Dtmf: Dual Tone Multi Frequency.
Enumerationr/w
Enumerated Values:
100mfR1
200dtmf
.0.1880.1.100.200.1.700
eamSignalingVariantsIncomingDialMapIncoming Dial Map

Defines the dial map expression to match against on the
incoming side. The dial map expression uses a special format
using macros that enables the user to construct a custom dial
map usi…
OctetStringr/w
Constraints:
range: 0-255
.0.1880.1.100.200.1.800
eamSignalingVariantsOutgoingDialMapOutgoing Dial Map

Defines the dial map format for the outgoing dial string. The
dial string generation uses a special format using macros
that enables the user to construct a custom dial string using
the …
OctetStringr/w
Constraints:
range: 0-255
.0.1880.1.100.200.1.900
eamSignalingVariantsWaitWinkWait Wink

Defines whether or not the outgoing register should wait for
a wink before proceeding with digit transmission.
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.200.1.1000
eamSignalingVariantsWaitWinkAckWait Wink Ack

Defines whether or not the outgoing register should wait for
a wink acknowledge after all digit reception.
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.200.1.1100
eamSignalingVariantsSendWinkSend Wink

Defines whether or not the incoming register should send a
wink to notify the remote side that digit information can be
sent.
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.200.1.1200
eamSignalingVariantsSendWinkAckSend Wink Ack

Defines whether or not the incoming register should send a
wink to acknowledge the receipt of all digits.
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.200.1.1300
eamSignalingVariantsResetSpecificReset Specific

Resets specific settings of E&M Signaling parameters with the
default signaling settings. This command is used to retrieve
the default configuration of the selected Signaling Type set
in th…
Enumerationr/w
Enumerated Values:
0noOp
10resetSpecific
.0.1880.1.100.200.1.2000
.0.1880.1.100.300 · 1 row entry · 14 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamTimerVariantsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamTimerVariantsTable'
E&M Signaling Timer Variants
          
This table allows to override or retrieve the default
signaling setting for E&M Timers.
eamTimerVariantsEntry row .0.1880.1.100.300.1
A row in table E&M Signaling Timer Variants.
Column Syntax OID
eamTimerVariantsInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.100.300.1.100
eamTimerVariantsOverrideDefaultOverride Default

Overrides the default settings of E&M Signaling parameters
for the SignalingType and InterfaceName.

* Disable: The interface uses the default configuration
associated…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.300.1.200
eamTimerVariantsBwdWaitPreWinkTimeoutSeizure Ack Timeout

Amount of time an incoming register waits before sending the
wink that acknowledges the seizure.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-2000
.0.1880.1.100.300.1.300
eamTimerVariantsBwdSendWinkTimeoutSend Wink Timeout

Duration of the wink signal applied by the incoming register
to signal seizure acknowledgment.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-5000
.0.1880.1.100.300.1.400
eamTimerVariantsBwdWait1stDigitTimeoutWait 1st Digit Timeout

Maximum time an incoming register waits for the first
incoming digit after the line seizure.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-20000
.0.1880.1.100.300.1.500
eamTimerVariantsBwdClearBackwardTimeoutClear Backward Timeout

The maximum time an incoming register waits after sending a
clear backward line signal before transiting to the idle
state.

This value is expressed in milliseconds (m…
Integer32r/w
Constraints:
range: 0-30000
.0.1880.1.100.300.1.600
eamTimerVariantsBwdDigitCompleteTimeoutDigit Complete Timeout

The maximum time the incoming register waits for the next
digit before considering the digit sequence as completed.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-15000
.0.1880.1.100.300.1.700
eamTimerVariantsFwdWaitWinkTimeoutWait Wink Timeout

Maximum time an outgoing register waits for seizure
acknowledgement after seizing the line.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.300.1.800
eamTimerVariantsFwdWaitMaxWinkOnTimeoutWait Max Wink On Timeout

The maximum time an outgoing register waits for the seizure
acknowledgment wink to complete.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.300.1.900
eamTimerVariantsFwdWaitPreDialTimeoutWait PreDial Timeout

The amount of time an outgoing register waits after the wink
to start dialing.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-5000
.0.1880.1.100.300.1.1000
eamTimerVariantsFwdWaitAnswerTimeoutWait Answer Timeout

The maximum time an outgoing register waits for the call to
be answered.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-300000
.0.1880.1.100.300.1.1100
eamTimerVariantsFwdClearForwardTimeoutClear Forward Timeout

The maximum time an outgoing register waits after sending a
clear forward line signal before transiting to the idle
state.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-30000
.0.1880.1.100.300.1.1200
eamTimerVariantsReleaseGuardTimeoutRelease Guard Timeout

Maximum time a register waits after sending an idle line
signal to prevent a new seizure of the line.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.300.1.1300
eamTimerVariantsResetSpecificReset Specific

Resets specific settings of E&M Timers parameters with the
default signaling type settings. This command is used to
retrieve the default configuration of the selected Signaling
Type set in …
Enumerationr/w
Enumerated Values:
0noOp
10resetSpecific
.0.1880.1.100.300.1.1900
.0.1880.1.100.400 · 1 row entry · 5 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamDigitTimerVariantsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamDigitTimerVariantsTable'
E&M Digit Timer Variants
          
This table allows to override or retrieve the default
signaling type setting for E&M Digit Timers.
eamDigitTimerVariantsEntry row .0.1880.1.100.400.1
A row in table E&M Digit Timer Variants.
Column Syntax OID
eamDigitTimerVariantsInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.100.400.1.100
eamDigitTimerVariantsOverrideDefaultOverride Default

Overrides the default settings of E&M Signaling parameters
for the SignalingType and InterfaceName.

* Disable: The interface uses the default configuration
associated…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.400.1.200
eamDigitTimerVariantsKPOnTimeoutDuration of the MF R1 KP signal

The time during which the MF R1 KP tone is on.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.400.1.300
eamDigitTimerVariantsKPOffTimeoutDuration of the off portion of the MF R1 KP signal

The duration of the pause after the MF R1 KP tone.

This value is expressed in milliseconds (ms).
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.400.1.400
eamDigitTimerVariantsResetSpecificReset Specific

Resets specific settings of E&M Digit Timers parameters with
the default signaling type settings. This command is used to
retrieve the default configuration of the selected Signaling
Type s…
Enumerationr/w
Enumerated Values:
0noOp
10resetSpecific
.0.1880.1.100.400.1.900
.0.1880.1.100.500 · 1 row entry · 5 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamLinkTimerVariantsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamLinkTimerVariantsTable'
E&M Link Timer Variants
          
This table allows to override or retrieve the default
signaling type setting for E&M Link Timers.
eamLinkTimerVariantsEntry row .0.1880.1.100.500.1
A row in table E&M Link Timer Variants.
Column Syntax OID
eamLinkTimerVariantsInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.100.500.1.100
eamLinkTimerVariantsOverrideDefaultOverride Default

Overrides the default settings of E&M Signaling parameters
for the SignalingType and InterfaceName.

* Disable: The interface uses the default configuration
associated…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.500.1.200
eamLinkTimerVariantsLinkActivationTimeoutLink Activation Timeout

The maximum time the unit waits for an activation indication
coming from the physical link. The activation indication is
used to indicate that the physical layer connection has bee…
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.500.1.300
eamLinkTimerVariantsLinkActivationRetryTimeoutLink Activation Retry Timeout

The maximum time the unit waits before attempting to
reestablish the physical link. The attempt is made when the
physical layer connection has been deactivated.
…
Integer32r/w
Constraints:
range: 0-10000
.0.1880.1.100.500.1.400
eamLinkTimerVariantsResetSpecificReset Specific

Resets specific settings of E&M Link Timers parameters with
the default signaling settings. This command is used to
retrieve the default signaling configuration set in the
SignalingType par…
Enumerationr/w
Enumerated Values:
0noOp
10resetSpecific
.0.1880.1.100.500.1.900
.0.1880.1.100.600 · 1 row entry · 5 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk eamToneVariantsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::eamToneVariantsTable'
E&M Signaling Tone Variants
          
This table allows to override or retrieve the default
signaling setting for E&M Tone variants.
eamToneVariantsEntry row .0.1880.1.100.600.1
A row in table E&M Signaling Tone Variants.
Column Syntax OID
eamToneVariantsInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.100.600.1.100
eamToneVariantsOverrideDefaultOverride Default

Overrides the default settings of E&M Signaling parameters
for the SignalingType and InterfaceName.

* Disable: The interface uses the default configuration
associated…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.100.600.1.200
eamToneVariantsKpToneKP (start-of-pulsing) Tone

Specifies the KP (start-of-pulsing) signal.

* None : No tone used.
* MF0..MF14 : MF R1 Tone
Enumerationr/w
Enumerated Values:
100none
200mF0
300mF1
400mF2
500mF3
600mF4
700mF5
800mF6
900mF7
1000mF8
1100mF9
1200mF10
1300mF11
1400mF12
1500mF13
1600mF14
.0.1880.1.100.600.1.300
eamToneVariantsStToneST (end-of-pulsing) Tone

Specifies the ST (end-of-pulsing) signal.

* None : No tone used.
* MF0..MF14 : MF R1 Tone
Enumerationr/w
Enumerated Values:
100none
200mF0
300mF1
400mF2
500mF3
600mF4
700mF5
800mF6
900mF7
1000mF8
1100mF9
1200mF10
1300mF11
1400mF12
1500mF13
1600mF14
.0.1880.1.100.600.1.400
eamToneVariantsResetSpecificReset Specific

Resets specific settings of E&M Tones parameters with the
default signaling settings. This command is used to retrieve
the default signaling configuration set in the SignalingType
parameter.
Enumerationr/w
Enumerated Values:
0noOp
10resetSpecific
.0.1880.1.100.600.1.900
.0.1880.1.200.100 · 1 row entry · 2 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk bearerChannelInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::bearerChannelInfoTable'
Bearer Channel Info
          
Port-specific operational, statistics, and active call data
for B channels.
bearerChannelInfoEntry row .0.1880.1.200.100.1
A row in table Bearer Channel Info.
Column Syntax OID
bearerChannelInfoIndexIndex

Identifies the Bearer Channel..
OctetString.0.1880.1.200.100.1.100
bearerChannelInfoStateState

The current call control state for this channel:

* Idle: The channel is available
* InUse: The channel is currently used
* Maintenance: Maintenance state, temporarily unavailabl…
Enumeration
Enumerated Values:
100idle
200inUse
300maintenance
400error
500disabled
.0.1880.1.200.100.1.200
.0.1880.1.300.100 · 1 row entry · 2 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk physicalLinkInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::physicalLinkInfoTable'
Physical Link Information
          
The physical link information table contains status
information for all interfaces on this managed device.
physicalLinkInfoEntry row .0.1880.1.300.100.1
A row in table Physical Link Information.
Column Syntax OID
physicalLinkInfoInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.300.100.1.100
physicalLinkInfoStateState

The layer 1 state for this interface:

* Up: Layer 1 connectivity.
* Down: No layer 1 connectivity. The interface might be in
this state because no cable is plugged in or a pin…
Enumeration
Enumerated Values:
100up
200down
.0.1880.1.300.100.1.200
.0.1880.1.300.200 · 1 row entry · 6 columns
Uses the media5 variant from /opt/observium/mibs/media5.
Command help
Walk physicalLinkTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MX-EAM-MIB' -M '/opt/observium/mibs/media5:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MX-EAM-MIB::physicalLinkTable'
Physical Link
          
The physical link table containing configuration and
operational parameters for all interfaces on this managed
device.
physicalLinkEntry row .0.1880.1.300.200.1
A row in table Physical Link.
Column Syntax OID
physicalLinkInterfaceNameInterface Name

Identifies the interface.
OctetString.0.1880.1.300.200.1.100
physicalLinkLineCodingLine Coding

Defines the transmission encoding of bits:

* B8ZS: Bipolar with 8-Zeros Substitution (T1 lines)
* HDB3: High-Density Bipolar with 3-zeros (E1 lines)
* AMI: Alternate Mark …
Enumerationr/w
Enumerated Values:
100b8zs
200hdb3
300ami
.0.1880.1.300.200.1.200
physicalLinkLineFramingLine Framing

Defines the frame format:

* SF: Super frame. Sometimes known as D4 (T1 lines)
* ESF: Extended super frame (T1 lines)
* CRC4: Cyclic redundancy check 4 (E1 lines)
* NO-C…
Enumerationr/w
Enumerated Values:
100sf
200esf
300crc4
400noCrc4
.0.1880.1.300.200.1.300
physicalLinkClockModeClock Mode

A port can either generate the clocking for the line or
accept the clock from the line. The options master or slave
determine the clocking method:

* Master: Generates clock
*…
Enumerationr/w
Enumerated Values:
100master
200slave
.0.1880.1.300.200.1.400
physicalLinkMonitorLinkStateEnableMonitor Link State Enable

Monitors the physical link state of an E&M interface.

Enable: An E&M endpoint's operational state is affected by
its interface physical link state. When the link s…
MX-TCMxEnableStater/w
Type Values:
0disable
1enable
.0.1880.1.300.200.1.500
physicalLinkPortPinoutPort Pinout

Defines the port pinout:

* Auto: The pinout is set according to the clock mode.
* Master: Force the pinout to Master regardless of the
clock mode.
* Slave: Force the p…
Enumerationr/w
Enumerated Values:
100auto
200master
300slave
.0.1880.1.300.200.1.600