MS-SWITCH30-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

216

portStatusTable

table

.1.3.6.1.4.1.3181.10.3.3.10 · 1 row entry · 10 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk portStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::portStatusTable'

This table contains port status information 
of the device.

portStatusTableEntry row .1.3.6.1.4.1.3181.10.3.3.10.1

Entry in the port status table.

Indexes

portStatusId

Column Syntax OID

portStatusId

This entry describes the port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.3.10.1.1

portStatusType

This entry describes the type of the port.

Enumeration

Enumerated Values:

1	port-tx10-100
2	port-t10-100-1000
3	port-fx100
4	port-fx100-1000-sfp
5	port-x1000
6	port-tx10-100-1000-sfp
7	port-tx10-100-1000-1x9
254	undefined

.1.3.6.1.4.1.3181.10.3.3.10.1.2

portStatusLink

This entry describes the link status of
the port.

Enumeration

Enumerated Values:

1	up
2	down
254	undefined

.1.3.6.1.4.1.3181.10.3.3.10.1.3

portStatusSpeed

This entry describes the current speed
status of the port if available.

Enumeration

Enumerated Values:

1	speed10
2	speed100
3	speed1000
254	undefined

.1.3.6.1.4.1.3181.10.3.3.10.1.4

portStatusDuplex

This entry describes the current duplex
status of the port if available.

Enumeration

Enumerated Values:

1	halfduplex
2	fullduplex
254	undefined

.1.3.6.1.4.1.3181.10.3.3.10.1.5

portStatusFlowControl

This entry describes the current flow
control status of the port if available.
This state referres the current duplex mode.

Enumeration

Enumerated Values:

1	enabled
2	disabled
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.10.1.6

portStatusPinout

This entry describes the current pinout
status of the port if available.

Enumeration

Enumerated Values:

1	mdi
2	mdix
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.10.1.7

portStatusFarEndFault

This entry describes the current
Far End Fault Detection status of
the port if available.

Enumeration

Enumerated Values:

1	detected
2	undetected
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.10.1.8

portStatusRxNetload

This entry describes the receiver netload
in percent, adapted to the selected port
speed. Netload values greater than '0' but
less that '1' are rounded up to a '1' to
differentiate them from real zero-values.
If net…

Integer32

Constraints:
range: -1-100

.1.3.6.1.4.1.3181.10.3.3.10.1.9

portStatusTxNetload

This entry describes the transmitter netload
in percent, adapted to the selected port
speed. Netload values greater than '0' but
less that '1' are rounded up to a '1' to
differentiate them from real zero-values.
If …

Integer32

Constraints:
range: -1-100

.1.3.6.1.4.1.3181.10.3.3.10.1.10

portConfigTable

table

.1.3.6.1.4.1.3181.10.3.3.20 · 1 row entry · 11 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk portConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::portConfigTable'

This table contains the port configuration 
of the device.

portConfigTableEntry row .1.3.6.1.4.1.3181.10.3.3.20.1

Entry in the port configuration table.

Indexes

portConfigId

Column Syntax OID

portConfigId

This entry describes the device's port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.3.20.1.1

portConfigAlias

This entry contains an individual name
for the port.

OctetStringr/w

Constraints:
range: 0-20

.1.3.6.1.4.1.3181.10.3.3.20.1.2

portConfigEnable

This entry describes the type of the port.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.3

portConfigAutonego

This entry describes the current
autonegotiation configuration of
the port if available.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.4

portConfigSpeed

This entry describes the current speed
configuration of the port if available.
This entry is only valid if Autonegotiation
is disabled.

Enumerationr/w

Enumerated Values:

1	force10
2	force100
3	force1000
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.5

portConfigDuplex

This entry describes the current duplex
configuration of the port if available.
This entry is only valid if Autonegotiation
is disabled.

Enumerationr/w

Enumerated Values:

1	forcehalf
2	forcefull
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.6

portConfigFlowControl

This entry describes the current flow
control configuration of the port if
available. The current duplex mode is
is used to to select the matching settings.
This entry is used for advertising if
Autonegotiation is en…

Enumerationr/w

Enumerated Values:

1	advertise
2	avoid
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.7

portConfigPinout

This entry describes the current pinout
configuration of a copper port if available.

Enumerationr/w

Enumerated Values:

0	auto
1	mdi
2	mdix
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.8

portConfigFarEndFault

This entry describes the current far end
fault behaviour of a fiber port if
available.

Enumerationr/w

Enumerated Values:

1	enabled
2	disalbed
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.9

portConfigAdvertise

This entry describes the autonegotiation
advertise information of the port.

Enumerationr/w

Enumerated Values:

1	advertiseGigabit
2	avoidGigabit
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.10

portConfigFibreDownDetection

This entry describes the current fibre
down detection behaviour of a fiber port
if available.

Enumerationr/w

Enumerated Values:

1	enabled
2	disalbed
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.3.20.1.11

vlanPortTable

table

.1.3.6.1.4.1.3181.10.3.4.10 · 1 row entry · 5 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk vlanPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::vlanPortTable'

This table contains the vlan port 
configuration.

vlanPortTableEntry row .1.3.6.1.4.1.3181.10.3.4.10.1

Entry in the vlan port configuration
table.

Indexes

vlanPortId

Column Syntax OID

vlanPortId

This entry describes the port id for the
vlan port table. The port id '0' is used
for the internal management agent port.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.4.10.1.1

vlanPortMode

This entry describes the vlan mode the port.

Enumerationr/w

Enumerated Values:

1	access
2	trunk
3	hybrid
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.10.1.2

vlanDefaultVID

This entry describes default vid for the port.

Integer32r/w

Constraints:
range: 0-4095

.1.3.6.1.4.1.3181.10.3.4.10.1.3

vlanDefaultPriority

This entry describes default priority tag
for the port.

Integer32r/w

Constraints:
range: 0-7

.1.3.6.1.4.1.3181.10.3.4.10.1.4

vlanPortFlags

This Entry contains per port some bitwise
filter settings:
Bit 0: Force Port Default VID (only valid if
vlanForceDefaultVID is set to '3')
Bit 1: per VID Priority Override

Integer32r/w

Constraints:
range: 0-3

.1.3.6.1.4.1.3181.10.3.4.10.1.5

vlanFilterTable

table

.1.3.6.1.4.1.3181.10.3.4.20 · 1 row entry · 29 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk vlanFilterTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::vlanFilterTable'

This table contains the vlan filter 
configuration.

vlanFilterTableEntry row .1.3.6.1.4.1.3181.10.3.4.20.1

Entry in the vlan filter configuration table.

Indexes

vlanFilterId

Column Syntax OID

vlanFilterId

This entry contains the filter id for the
vlan filter table.

Integer32

Constraints:
range: 1-64

.1.3.6.1.4.1.3181.10.3.4.20.1.1

vlanFilterVID

This entry describes the vlan id for the
filter.

Integer32r/w

Constraints:
range: 0-4095

.1.3.6.1.4.1.3181.10.3.4.20.1.2

vlanFilterAlias

This entry describes an individual name
for the vlan filter.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.4.20.1.3

vlanFilterEnable

This entry enables or disabled the vlan
filter.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.4

vlanMemberManager

This entry defines the membership of the
management agent to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.5

vlanMemberPort1

This entry defines the membership of
port 1 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.6

vlanMemberPort2

This entry defines the membership of
port 2 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.7

vlanMemberPort3

This entry defines the membership of
port 3 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.8

vlanMemberPort4

This entry defines the membership of
port 4 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.9

vlanMemberPort5

This entry defines the membership of
port 5 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.10

vlanMemberPort6

This entry defines the membership of
port 6 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.11

vlanMemberPort7

This entry defines the membership of
port 7 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.12

vlanMemberPort8

This entry defines the membership of
port 8 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.13

vlanMemberPort9

This entry defines the membership of
port 9 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.14

vlanMemberPort10

This entry defines the membership of
port 10 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.15

vlanMemberPort11

This entry defines the membership of
port 11 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.16

vlanMemberPort12

This entry defines the membership of
port 12 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.17

vlanMemberPort13

This entry defines the membership of
port 13 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.18

vlanMemberPort14

This entry defines the membership of
port 14 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.19

vlanMemberPort15

This entry defines the membership of
port 15 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.20

vlanMemberPort16

This entry defines the membership of
port 16 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.21

vlanMemberPort17

This entry defines the membership of
port 17 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.22

vlanMemberPort18

This entry defines the membership of
port 18 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.23

vlanMemberPort19

This entry defines the membership of
port 19 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.24

vlanMemberPort20

This entry defines the membership of
port 20 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.25

vlanMemberPort21

This entry defines the membership of
port 21 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.26

vlanMemberPort22

This entry defines the membership of
port 22 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.27

vlanMemberPort23

This entry defines the membership of
port 23 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.28

vlanMemberPort24

This entry defines the membership of
port 24 to the filter.

Enumerationr/w

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.4.20.1.29

vlanFilterEnhTable

table

.1.3.6.1.4.1.3181.10.3.4.30 · 1 row entry · 3 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk vlanFilterEnhTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::vlanFilterEnhTable'

This table contains the enhanced 
vlan filter configuration.

vlanFilterEnhTableEntry row .1.3.6.1.4.1.3181.10.3.4.30.1

Entry in the vlan filter enhanced
configuration table.

Indexes

vlanFilterEnhId

Column	Syntax	OID
vlanFilterEnhId This entry contains the filter id for the enhanced vlan filter table.	Integer32 Constraints: `range: 1-64`	`.1.3.6.1.4.1.3181.10.3.4.30.1.1`
vlanFilterEnhFlags This Entry contains some flags for VLAN filter settings. The content is defined as following: Bit 0: Filter Enabled Bit 1: per VID Priority Override Enabled	Integer32r/w Constraints: `range: 0-3`	`.1.3.6.1.4.1.3181.10.3.4.30.1.2`
vlanFilterEnhPriOverride This entry contains the priority value to override an ingress frame with if its VLAN ID fits, filtering is enabled, port selective override flag is set and filter selective override flag is set.	Integer32r/w Constraints: `range: 0-7`	`.1.3.6.1.4.1.3181.10.3.4.30.1.3`

prioPortTable

table

.1.3.6.1.4.1.3181.10.3.5.10 · 1 row entry · 2 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk prioPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::prioPortTable'

This table contains the port prioritization 
of the device. This setting is always valid 
if no other type of prioritization has been 
selected.

prioPortTableEntry row .1.3.6.1.4.1.3181.10.3.5.10.1

Entry in the port prioritization table.

Indexes

prioPortId

Column	Syntax	OID
prioPortId This entry describes the device's port id.	Integer32 Constraints: `range: 1-24`	`.1.3.6.1.4.1.3181.10.3.5.10.1.1`
prioPortQueue This entry describes the selected queue if port prioritization is available.	Integer32r/w Constraints: `range: 0-3`	`.1.3.6.1.4.1.3181.10.3.5.10.1.2`

prioIeeeTagTable

table

.1.3.6.1.4.1.3181.10.3.5.20 · 1 row entry · 2 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk prioIeeeTagTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::prioIeeeTagTable'

This table contains the configuuration of 
IEEE 802.1p prioritization. Each of the 8 
different values is assigned to one of the
available queues here.

prioIeeeTagTableEntry row .1.3.6.1.4.1.3181.10.3.5.20.1

Entry in the IEEE 802.1p tag prioritization
table.

Indexes

prioIeeeTagId

Column	Syntax	OID
prioIeeeTagId This entry defines the IEEE 802.1p tag a queue is assigned to.	Integer32 Constraints: `range: 0-7`	`.1.3.6.1.4.1.3181.10.3.5.20.1.1`
prioIeeeTagQueue This entry describes the selected queue for each IEEE 802.1p tag.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.3181.10.3.5.20.1.2`

prioDiffservTable

table

.1.3.6.1.4.1.3181.10.3.5.30 · 1 row entry · 2 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk prioDiffservTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::prioDiffservTable'

This table contains the configuuration 
of DiffServ prioritization. Each of the 
64 different values is assigned to one 
of the available queues here.

prioDiffservTableEntry row .1.3.6.1.4.1.3181.10.3.5.30.1

Entry in the Diffserv prioritization table.

Indexes

prioDiffservId

Column	Syntax	OID
prioDiffservId This entry defines the Diffserv index a queue is assigned to.	Integer32 Constraints: `range: 0-63`	`.1.3.6.1.4.1.3181.10.3.5.30.1.1`
prioDiffservQueue This entry describes the selected queue for each Diffserv index.	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.3181.10.3.5.30.1.2`

ringTable

table

.1.3.6.1.4.1.3181.10.3.7.10 · 1 row entry · 7 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk ringTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::ringTable'

This table contains the ring configuration 
of the device.

ringTableEntry row .1.3.6.1.4.1.3181.10.3.7.10.1

Entry in the ring configuration table.

Indexes

ringId

Column Syntax OID

ringId

This entry describes the ring id.

Integer32

Constraints:
range: 1-3

.1.3.6.1.4.1.3181.10.3.7.10.1.1

ringMode

This entry enables or disables ring mode
and selects the mode of operation.

Enumerationr/w

Enumerated Values:

1	slave
2	master
3	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.7.10.1.2

ringPortA

This entry defines port A for the ring
function. If the device is a 'master'
this is the main port. If ring feature
is not supported a 255 will be replied.

Integer32r/w

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.7.10.1.3

ringPortB

This entry defines port B for the ring
function. If the device is a 'master'
this is the backup port. If ring feature
is not supported a 255 will be replied.

Integer32r/w

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.7.10.1.4

ringNumber

This entry defines the ring ID number.
If ring feature is not supported a 255
will be replied.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.3181.10.3.7.10.1.5

ringStatus

This entry defines the ring status.

Enumeration

Enumerated Values:

1	ringOk
2	ringFailure
3	ringDisabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.7.10.1.6

ringAlarmDuration

Duration of ring alarm status (in 0.01s).
This entry is used as additional status
information in repeated ring alarm traps
if error status remains unchanged.
A value of '0' means 'no ring alarm'

SNMPv2-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.3181.10.3.7.10.1.7

sfpTable

table

.1.3.6.1.4.1.3181.10.3.9.10 · 1 row entry · 16 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk sfpTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::sfpTable'

This table contains the sfp module 
status of the device.

sfpTableEntry row .1.3.6.1.4.1.3181.10.3.9.10.1

Entry in the sfp status table.

Indexes

sfpId

Column Syntax OID

sfpId

This entry describes the sfp id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.9.10.1.1

sfpPortnumber

This entry describes the number of the port
where the sfp can be plugged in.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.2

sfpDetect

This entry enables or disables uplink
redundancy

Enumeration

Enumerated Values:

1	plugged
2	unplugged
255	unsupported

.1.3.6.1.4.1.3181.10.3.9.10.1.3

sfpVendor

This entry describes the vendor name of
the sfp.

OctetString

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.9.10.1.4

sfpVendorPartnumber

This entry describes the vendor
partnumber of the sfp.

OctetString

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.9.10.1.5

sfpVendorSerialnumber

This entry describes the vendor
serialnumber of the sfp.

OctetString

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.9.10.1.6

sfpConnector

This entry describes the type of
connector of the sfp.

Enumeration

Enumerated Values:

1	connSC
7	connLC
8	connMTRJ
255	unsupported

.1.3.6.1.4.1.3181.10.3.9.10.1.7

sfpNominalBitrate

This entry describes the nominal bitrate
of the sfp. It is a maximum value, a lower
value may be used instead.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.8

sfpDiagnostic

This entry describes tha avalability and
type of diagnostics.

Enumeration

Enumerated Values:

1	supportedWithInternalCalibration
2	supportedWithExternalCalibration
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.9.10.1.9

sfpTemperature

This entry describes the temperature of
the sfp in multiple of 0.1 degree celsius.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.10

sfpVoltage

This entry describes the supply voltage
of the sfp in multiple of 0.01 V.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.11

sfpTxBias

This entry describes the transmit bias
current of the sfp in multiple of 0.01 mA.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.12

sfpTxPower

This entry describes the optical transmit
power of the sfp in multiple of 0.1 uW.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.13

sfpRxPower

This entry describes the ooptical receive
power of the sfp in multiple of 0.1 uW.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.9.10.1.14

sfpWarnings

This entry contains the flags for internal
warnings. A warning occurrs if regarding
warning threshold is exceeded.

Bits

Enumerated Values:

0	tempHighWarn
1	tempLowWarn
2	vccHighWarn
3	vccLowWarn
4	txBiasHighWarn
5	txBiasLowWarn
6	txPowerHighWarn
7	txPowerLowWarn
8	rxPowerHighWarn
9	rxPowerLowWarn

.1.3.6.1.4.1.3181.10.3.9.10.1.15

sfpAlarms

This entry contains the flags for internal
alarms. An alarm occurrs if regarding
alarm threshold is exceeded.

Bits

Enumerated Values:

0	tempHighAlarm
1	tempLowAlarm
2	vccHighAlarm
3	vccLowAlarm
4	txBiasHighAlarm
5	txBiasLowAlarm
6	txPowerHighAlarm
7	txPowerLowAlarm
8	rxPowerHighAlarm
9	rxPowerLowAlarm

.1.3.6.1.4.1.3181.10.3.9.10.1.16

relaisTable

table

.1.3.6.1.4.1.3181.10.3.11.10 · 1 row entry · 4 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk relaisTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::relaisTable'

This table contains the relais 
configuration of the device.

relaisTableEntry row .1.3.6.1.4.1.3181.10.3.11.10.1

Entry in the relais configuration table.

Indexes

relaisId

Column Syntax OID

relaisId

This entry describes the relais id.

Integer32

Constraints:
range: 1-4

.1.3.6.1.4.1.3181.10.3.11.10.1.1

relaisAlias

This entry contains an individual name
for the relais.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.11.10.1.2

relaisMode

This entry describes the bahaviour of
the alarm relais.

Enumerationr/w

Enumerated Values:

1	openOnEvent
2	closeOnEvent
255	unsupported

.1.3.6.1.4.1.3181.10.3.11.10.1.3

relaisStatus

This entry describes the present status
of the alarm relais.

Enumerationr/w

Enumerated Values:

1	closed
2	opened
255	unsupported

.1.3.6.1.4.1.3181.10.3.11.10.1.4

pacStatusTable

table

.1.3.6.1.4.1.3181.10.3.12.100 · 1 row entry · 19 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk pacStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::pacStatusTable'

This table contains the port status
of the port access control feature.

pacStatusTableEntry row .1.3.6.1.4.1.3181.10.3.12.100.1

Entry in the port access control
port status table.

Indexes

pacStatPortId

Column Syntax OID

pacStatPortId

This entry describes the port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.12.100.1.1

pacStatPortMode

This entry describes the port
access control mode.

Enumeration

Enumerated Values:

1	forceAuthorized
2	macLocking
3	radiusMacAuthentication
4	ieee8021XAuthentication
5	forceUnauthorized
6	parallel8021XMACauth
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.2

pacStatPortStatus

This entry describes the port
access control status.

Enumeration

Enumerated Values:

1	authorized
2	unauthorized
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.3

pacStatUserStatus1

This entry describes the port
access control mode status for
the first host.
Note, that different states of
several authentication methods
are summarized here. They are
marked with different multiples
of ten as an of…

Enumeration

Enumerated Values:

10	authorized1
11	unauthorized1
12	tobedone1
20	authorized2
21	unauthorized2
22	tobedone2
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.4

pacStatUserStatus2

This entry describes the port
access control mode status for
the second host.
Note, that different states of
several authentication methods
are summarized here. They are
marked with different multiples
of ten as an o…

Enumeration

Enumerated Values:

10	authorized1
11	unauthorized1
12	tobedone1
20	authorized2
21	unauthorized2
22	tobedone2
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.5

pacStatUserStatus3

This entry describes the port
access control mode status for
the third host.
Note, that different states of
several authentication methods
are summarized here. They are
marked with different multiples
of ten as an of…

Enumeration

Enumerated Values:

10	authorized1
11	unauthorized1
12	tobedone1
20	authorized2
21	unauthorized2
22	tobedone2
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.6

pacStatUserStatus4

This entry describes the port
access control mode status for
the fourth host.
Note, that different states of
several authentication methods
are summarized here. They are
marked with different multiples
of ten as an o…

Enumeration

Enumerated Values:

10	authorized1
11	unauthorized1
12	tobedone1
20	authorized2
21	unauthorized2
22	tobedone2
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.100.1.7

pacStatUserMac1

This entry contains the 1st host
mac address at the selected port
if available.

RFC1213-MIBPhysAddress

.1.3.6.1.4.1.3181.10.3.12.100.1.8

pacStatUserMac2

This entry contains the 2nd host
mac address at the selected port
if available.

RFC1213-MIBPhysAddress

.1.3.6.1.4.1.3181.10.3.12.100.1.9

pacStatUserMac3

This entry contains the 3rd host
mac address at the selected port
if available.

RFC1213-MIBPhysAddress

.1.3.6.1.4.1.3181.10.3.12.100.1.10

pacStatUserMac4

This entry contains the 4th host
mac address at the selected port
if available.

RFC1213-MIBPhysAddress

.1.3.6.1.4.1.3181.10.3.12.100.1.11

pacStatUserName1

This entry contains the 1st host
user name at the selected port
if available.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.3181.10.3.12.100.1.12

pacStatUserName2

This entry contains the 2nd host
user name at the selected port
if available.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.3181.10.3.12.100.1.13

pacStatUserName3

This entry contains the 3rd host
user name at the selected port
if available.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.3181.10.3.12.100.1.14

pacStatUserName4

This entry contains the 4th host
user name at the selected port
if available.

OctetString

Constraints:
range: 0-32

.1.3.6.1.4.1.3181.10.3.12.100.1.15

pacStatUserIp1

This entry contains the 1st host
ip address at the selected port
if available.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.12.100.1.16

pacStatUserIp2

This entry contains the 2nd host
ip address at the selected port
if available.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.12.100.1.17

pacStatUserIp3

This entry contains the 3rd host
ip address at the selected port
if available.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.12.100.1.18

pacStatUserIp4

This entry contains the 4th host
ip address at the selected port
if available.

SNMPv2-SMIIpAddress

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.12.100.1.19

pacConfigTable

table

.1.3.6.1.4.1.3181.10.3.12.110 · 1 row entry · 3 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk pacConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::pacConfigTable'

This table contains the port status
of the port access control feature.

pacConfigTableEntry row .1.3.6.1.4.1.3181.10.3.12.110.1

Entry in the port access control
port config table.

Indexes

pacConfPortId

Column Syntax OID

pacConfPortId

This entry describes the port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.12.110.1.1

pacConfMode

This entry describes the port
access control mode .

Enumerationr/w

Enumerated Values:

1	forceAuthorized
2	macLocking
3	radiusMacAuthentication
4	ieee8021xAuthentication
5	forceUnauthorized
6	parallel8021XMACauth
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.110.1.2

pacConfMaxMacCount

This entry contains the maximum number of
accessible hosts for the selected port if
mode is set to 'Radius Authentication' or
'ieee 802.1x-Authentication.

Integer32r/w

Constraints:
range: 1-4

.1.3.6.1.4.1.3181.10.3.12.110.1.3

pacMacLockingTable

table

.1.3.6.1.4.1.3181.10.3.12.120 · 1 row entry · 13 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk pacMacLockingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::pacMacLockingTable'

This table contains the port status
of the port access control feature.

pacMacLockTableEntry row .1.3.6.1.4.1.3181.10.3.12.120.1

Entry in the port access control
port status table.

Indexes

pacMacLockPortId

Column Syntax OID

pacMacLockPortId

This entry describes the port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.12.120.1.1

pacMacLockEnable1

This entry describes if the host with
the 1st locked Mac Address gets access
to the selected port or not.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.2

pacMacLockEnable2

This entry describes if the host with
the 2nd locked Mac Address gets access
to the selected port or not.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.3

pacMacLockEnable3

This entry describes if the host with
the 3rd locked Mac Address gets access
to the selected port or not.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.4

pacMacLockEnable4

This entry describes if the host with
the 4th locked Mac Address gets access
to the selected port or not.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.5

pacMacLockLearn1

This entry describes if the 1st
Mac Address to lock at the selected port
has to be learned or if it is fixed.

Enumerationr/w

Enumerated Values:

1	learn
2	fixed
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.6

pacMacLockLearn2

This entry describes if the 2nd
Mac Address to lock at the selected port
has to be learned or if it is fixed.

Enumerationr/w

Enumerated Values:

1	learn
2	fixed
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.7

pacMacLockLearn3

This entry describes if the 3rd
Mac Address to lock at the selected port
has to be learned or if it is fixed.

Enumerationr/w

Enumerated Values:

1	learn
2	fixed
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.8

pacMacLockLearn4

This entry describes if the 4th
Mac Address to lock at the selected port
has to be learned or if it is fixed.

Enumerationr/w

Enumerated Values:

1	learn
2	fixed
255	unsupported

.1.3.6.1.4.1.3181.10.3.12.120.1.9

pacLockedMac1

This entry contains the 1st
locked mac address at
the selected port.

RFC1213-MIBPhysAddressr/w

.1.3.6.1.4.1.3181.10.3.12.120.1.10

pacLockedMac2

This entry contains the 2nd
locked mac address at
the selected port.

RFC1213-MIBPhysAddressr/w

.1.3.6.1.4.1.3181.10.3.12.120.1.11

pacLockedMac3

This entry contains the 3rd
locked mac address at
the selected port.

RFC1213-MIBPhysAddressr/w

.1.3.6.1.4.1.3181.10.3.12.120.1.12

pacLockedMac4

This entry contains the 4th
locked mac address at
the selected port.

RFC1213-MIBPhysAddressr/w

.1.3.6.1.4.1.3181.10.3.12.120.1.13

igmpsPortTable

table

.1.3.6.1.4.1.3181.10.3.13.30 · 1 row entry · 4 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk igmpsPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::igmpsPortTable'

This table contains port status information 
of the device.

igmpsPortTableEntry row .1.3.6.1.4.1.3181.10.3.13.30.1

Entry in the port value table.

Indexes

igmpsPortId

Column Syntax OID

igmpsPortId

This entry describes the port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.13.30.1.1

igmpsPortSnooping

This entry determines if the port
is enabled for IGMP Snooping or
not (if supported).

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.30.1.2

igmpsPortStaticRouter

This entry determins if the port
is defined as static router port or
not (if supported).

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.30.1.3

igmpsPortDynamicRouter

This entry ddocuments if a router
has been detected at this port or
not (if supported).

Enumeration

Enumerated Values:

1	detected
2	undetected
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.30.1.4

igmpsGroupTable

table

.1.3.6.1.4.1.3181.10.3.13.40 · 1 row entry · 29 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk igmpsGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::igmpsGroupTable'

This table contains port status information 
of the device.

igmpsGroupTableEntry row .1.3.6.1.4.1.3181.10.3.13.40.1

Entry in the port value table.

Indexes

igmpsGroupId

Column Syntax OID

igmpsGroupId

This entry describes the Multicast
Group id.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.3181.10.3.13.40.1.1

igmpsGroupMac

This entry documents the Multicast Group's
MAC-Address.

RFC1213-MIBPhysAddress

.1.3.6.1.4.1.3181.10.3.13.40.1.2

igmpsGroupVlanId

This entry documents the Vlan ID
of the Multicast Group.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.13.40.1.3

igmpsGroupTimestamp

This entry documents the Timestamp
of the Multicast Group in seconds.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.13.40.1.4

igmpsGroupLeaveFlag

This entry documents if the Leave
Flag has been set or not.

Enumeration

Enumerated Values:

1	set
2	unset
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.5

igmpsGroupMemberPort1

This entry defines the membership of
port 1 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.6

igmpsGroupMemberPort2

This entry defines the membership of
port 2 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.7

igmpsGroupMemberPort3

This entry defines the membership of
port 3 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.8

igmpsGroupMemberPort4

This entry defines the membership of
port 4 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.9

igmpsGroupMemberPort5

This entry defines the membership of
port 5 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.10

igmpsGroupMemberPort6

This entry defines the membership of
port 6 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.11

igmpsGroupMemberPort7

This entry defines the membership of
port 7 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.12

igmpsGroupMemberPort8

This entry defines the membership of
port 8 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.13

igmpsGroupMemberPort9

This entry defines the membership of
port 9 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.14

igmpsGroupMemberPort10

This entry defines the membership of
port 10 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.15

igmpsGroupMemberPort11

This entry defines the membership of
port 11 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.16

igmpsGroupMemberPort12

This entry defines the membership of
port 12 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.17

igmpsGroupMemberPort13

This entry defines the membership of
port 13 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.18

igmpsGroupMemberPort14

This entry defines the membership of
port 14 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.19

igmpsGroupMemberPort15

This entry defines the membership of
port 15 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.20

igmpsGroupMemberPort16

This entry defines the membership of
port 16 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.21

igmpsGroupMemberPort17

This entry defines the membership of
port 17 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.22

igmpsGroupMemberPort18

This entry defines the membership of
port 18 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.23

igmpsGroupMemberPort19

This entry defines the membership of
port 19 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.24

igmpsGroupMemberPort20

This entry defines the membership of
port 20 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.25

igmpsGroupMemberPort21

This entry defines the membership of
port 21 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.26

igmpsGroupMemberPort22

This entry defines the membership of
port 22 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.27

igmpsGroupMemberPort23

This entry defines the membership of
port 23 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.28

igmpsGroupMemberPort24

This entry defines the membership of
port 24 to the Multicast Group.

Enumeration

Enumerated Values:

1	yes
2	no
255	unsupported

.1.3.6.1.4.1.3181.10.3.13.40.1.29

rtcSNTPServerTable

table

.1.3.6.1.4.1.3181.10.3.15.20 · 1 row entry · 4 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk rtcSNTPServerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::rtcSNTPServerTable'

This table contains the configuration for 
several SNTP servers.

rtcSNTPServerTableEntry row .1.3.6.1.4.1.3181.10.3.15.20.1

Entry in the SNTP server table.

Indexes

rtcSNTPServerId

Column Syntax OID

rtcSNTPServerId

This entry contains the SNTP server ID.

Integer32

Constraints:
range: 1-4

.1.3.6.1.4.1.3181.10.3.15.20.1.1

rtcSNTPServerStatus

This entry describes the SNTP server
status as retransmitted after sync.

Enumeration

Enumerated Values:

0	ok
1	busy
2	timeout
3	nomemory
4	portbusy
5	alarm
7	unknown
255	unsupported

.1.3.6.1.4.1.3181.10.3.15.20.1.2

rtcSNTPServerEnable

This entry describes the SNTP server
enable status.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.15.20.1.3

rtcSNTPServerIpv4Address

This entry describes the SNTP
server IPv4 address.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.15.20.1.4

snmpTrapDestTable

table

.1.3.6.1.4.1.3181.10.3.22.10 · 1 row entry · 27 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk snmpTrapDestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::snmpTrapDestTable'

This table contains information regarding 
the snmp trap configuration for several 
destinations.

snmpTrapDestTableEntry row .1.3.6.1.4.1.3181.10.3.22.10.1

Entry in the snmp table.

Indexes

snmpTrapDestId

Column Syntax OID

snmpTrapDestId

This entry describes the snmp trap
destination id.

Integer32

Constraints:
range: 1-8

.1.3.6.1.4.1.3181.10.3.22.10.1.1

snmpTrapDestAlias

This entry contains an individual name
for the trap destination.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.22.10.1.2

snmpTrapDestEn

This entry describes the snmp trap
destination enable status and contains
the used snmp version.

Enumerationr/w

Enumerated Values:

0	disabled
1	v1
2	v2c
3	v3
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.3

snmpTrapDestIPv4Address

This is the trap receiver's IPv4 address.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.22.10.1.4

snmpTrapDestCommunity

This is the string used as community name
for traps.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.22.10.1.5

snmpTrapGenColdstart

This entry enables or disables the
transmission of generic coldstart
traps to the selected destination.
(generic trapnumber 0)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.6

snmpTrapGenWarmstart

This entry enables or disables the
transmission of generic warmstart
traps to the selected destination.
(generic trapnumber 1)

Enumeration

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.7

snmpTrapGenLinkDown

This entry enables or disables the
transmission of generic link down
traps to the selected destination.
(generic trapnumber 2)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.8

snmpTrapGenLinkUp

This entry enables or disables the
transmission of generic link up
traps to the selected destination.
(generic trapnumber 3)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.9

snmpTrapGenAuthFailure

This entry enables or disables the
transmission of generic authentication
failure traps to the selected destination.
(generic trapnumber 4)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.10

snmpTrapGenEgpNeighborLoss

This entry enables or disables the
transmission of generic Exterior Gateway
Protocol Neighbor Loss traps to the
selected destination.
(generic trapnumber 5)

Enumeration

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.11

snmpTrapEntLinkChange

This entry enables or disables the
transmission of enterprise link change
traps to the selected destination.
(generic trap# 6, specific trap# 1)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.12

snmpTrapEntFactoryReset

This entry enables or disables the
transmission of enterprise factory
reset traps to the selected destination.
(generic trap# 6, specific trap# 2)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.13

snmpTrapEntTemperatureLevelChange

This entry enables or disables the
transmission of enterprise temperature
level change traps to the selected
destination.
(generic trap# 6, specific trap# 3)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.14

snmpTrapEntErrorCounter

This entry enables or disables the
transmission of enterprise error counter
traps to the selected destination
(generic trap# 6, specific trap# 4)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.15

snmpTrapEntUnderOverVoltage

This entry enables or disables the
transmission of enterprise undervoltage
overvoltage traps to the selected
destination.
(generic trap# 6, specific trap# 5)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.16

snmpTrapEntTempShutDown

This entry enables or disables the
transmission of enterprise temperature
shut down event traps to the selected
destination.
(generic trap# 6, specific trap# 6)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.17

snmpTrapEntPoeLimitExceeded

This entry enables or disables the
transmission of enterprise poe limit
exceeded traps to the selected
destination.
(generic trap# 6, specific trap# 7)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.18

snmpTrapEntSupplyStatusChange

This entry enables or disables the
transmission of enterprise supply status
change traps to the selected destination.
(generic trap# 6, specific trap# 8)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.19

snmpTrapEntSfpPlugChange

This entry enables or disables the
transmission of enterprise SFP plug
change traps to the selected destination.
(generic trap# 6, specific trap# 9)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.20

snmpTrapEntLoginFailure

This entry enables or disables the
transmission of enterprise login failure
traps to the selected destination.
(generic trap# 6, specific trap# 10)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.21

snmpTrapEntRingBroken

This entry enables or disables the
transmission of enterprise Ring broken
traps to the selected destination.
(generic trap# 6, specific trap# 11)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.22

snmpTrapEntRingAlarm

This entry enables or disables the
transmission of enterprise Ring Alarm
traps to the selected destination.
(generic trap# 6, specific trap# 12)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.23

snmpTrapEntAuthPwFail

This entry enables or disables
the transmission of enterprise
SNMPv3 Authentication Password Fail traps
to the selected destination.
(generic trap# 6, specific trap# 13)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.24

snmpTrapEntPrivPwFail

This entry enables or disables
the transmission of enterprise
SNMPv3 Privacy Password Fail traps
to the selected destination.
(generic trap# 6, specific trap# 14)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.25

snmpTrapEntAccessPermission

This entry enables or disables
the transmission of enterprise
SNMPv3 Access Permission traps
to the selected destination.
(generic trap# 6, specific trap# 15)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.26

snmpTrapEntSeclevelFail

This entry enables or disables
the transmission of enterprise
SNMPv3 Security Level Fail traps
to the selected destination.
(generic trap# 6, specific trap# 16)

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.22.10.1.27

syslogDestTable

table

.1.3.6.1.4.1.3181.10.3.24.10 · 1 row entry · 7 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk syslogDestTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::syslogDestTable'

This table contains the configuration for 
several syslog destinations.

syslogDestTableEntry row .1.3.6.1.4.1.3181.10.3.24.10.1

Entry in the syslog destination table.

Indexes

syslogDestId

Column Syntax OID

syslogDestId

This entry contains the syslog
destination id.

Integer32

Constraints:
range: 1-8

.1.3.6.1.4.1.3181.10.3.24.10.1.1

syslogDestAlias

This entry contains an individual
name for the syslog destination.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.24.10.1.2

syslogDestEnable

This entry describes the syslog
destination enable status.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.24.10.1.3

syslogDestIpv4Address

This entry describes the syslog
destination IPv4 address.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.24.10.1.4

syslogDestPort

This is the syslog destination's
TCP port.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.24.10.1.5

syslogDestFacility

This entry describes the syslog
destination used facility value.

Enumerationr/w

Enumerated Values:

0	kernelMessage
1	userLevelMessage
2	mailSystem
3	systemDaemon
4	securityMessage1
5	syslogdMessage
6	linePrinterSubsystem
7	networkNewsSubsystem
8	uucpSubsystem
9	clockDeamon1
10	securityMessage2
11	ftpDeamon
12	ntpSubsystem
13	logAudit
14	logAlert
15	clockDeamon2
16	localUse0
17	localUse1
18	localUse2
19	localUse3
20	localUse4
21	localUse5
22	localUse6
23	localUse7

.1.3.6.1.4.1.3181.10.3.24.10.1.6

syslogDestEventFilter

Flags to filter syslog events:
messages are only sent if regarding
bits are set.

Bitsr/w

Enumerated Values:

0	reset
1	linkchange
2	configchange
3	login
4	firmwareupdate
5	powerredundancy
6	portauth
7	temperature
8	ring
9	sfp
10	poe
11	rtc
12	vct
29	debug
30	statusreport
31	test

.1.3.6.1.4.1.3181.10.3.24.10.1.7

radiusServerTable

table

.1.3.6.1.4.1.3181.10.3.25.10 · 1 row entry · 8 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk radiusServerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::radiusServerTable'

This table contains the configuration 
for several radius servers.

radiusServerTableEntry row .1.3.6.1.4.1.3181.10.3.25.10.1

Entry in the radius server table.

Indexes

radiusServerId

Column Syntax OID

radiusServerId

This entry contains the radius server id.

Integer32

Constraints:
range: 1-8

.1.3.6.1.4.1.3181.10.3.25.10.1.1

radiusServerAlias

This entry contains an individual name for
the radius server.

OctetStringr/w

Constraints:
range: 0-16

.1.3.6.1.4.1.3181.10.3.25.10.1.2

radiusServerEnableAccess

This entry describes the radius
server enable status for the
MAX-ACCESS service which means both,
authentication and authorization.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.25.10.1.3

radiusServerEnableAccount

This entry describes the radius
server enable status for the
account service.

Enumerationr/w

Enumerated Values:

1	enabled
2	disabled
255	unsupported

.1.3.6.1.4.1.3181.10.3.25.10.1.4

radiusServerIpv4Address

This entry describes the radius
server IPv4 address.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.3181.10.3.25.10.1.5

radiusServerAccessPort

This is the radius server's UDP port
for the access service. The default
value is 1812.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.25.10.1.6

radiusServerAccountPort

This is the radius server's UDP port
for the account service. The default
value is 1813.

SNMPv2-SMIInteger32r/w

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.25.10.1.7

radiusServerSecret

This is the radius server's secret string.

OctetStringr/w

Constraints:
range: 0-20

.1.3.6.1.4.1.3181.10.3.25.10.1.8

supplyTable

table

.1.3.6.1.4.1.3181.10.3.30.10 · 1 row entry · 3 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk supplyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::supplyTable'

This table contains power supply 
information of the device.

supplyTableEntry row .1.3.6.1.4.1.3181.10.3.30.10.1

Entry in the supply table.

Indexes

supplyId

Column Syntax OID

supplyId

This entry describes the power supply id.

Integer32

Constraints:
range: 1-8

.1.3.6.1.4.1.3181.10.3.30.10.1.1

supplyUsed

If several supplies are possible but not
required, this entry decides if an invalid
detection leads to an error. An error event
can be suppressed if a supply is marked as
'unused'. Hint: If an 'unused' supply is
de…

Enumerationr/w

Enumerated Values:

1	used
2	unused
255	unsupported

.1.3.6.1.4.1.3181.10.3.30.10.1.2

supplyStatus

This entry contains the information if the
power supply is valid at the moment. An
invalid supply will lead to an error event
unless it is marked as 'unused'.
Hint: If an 'unused' supply is detected as
'valid', it …

Enumeration

Enumerated Values:

1	valid
2	invalid
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.30.10.1.3

poepsePortTable

table

.1.3.6.1.4.1.3181.10.3.31.10 · 1 row entry · 8 columns

Open in standard view

Uses the microsens variant from /opt/observium/mibs/microsens.

Command help

Walk poepsePortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'MS-SWITCH30-MIB' -M '/opt/observium/mibs/microsens:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'MS-SWITCH30-MIB::poepsePortTable'

This table contains the pse port 
configuration of the device.

poepsePortTableEntry row .1.3.6.1.4.1.3181.10.3.31.10.1

Entry in the supply table.

Indexes

poepsePortId

Column Syntax OID

poepsePortId

This entry describes the device's pse
port id.

Integer32

Constraints:
range: 1-24

.1.3.6.1.4.1.3181.10.3.31.10.1.1

poepsePortMode

This entry describes the device's pse
port mode.

Enumerationr/w

Enumerated Values:

1	poe8023af
2	poeForced
3	poeDisabled
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.31.10.1.2

poepsePortStatus

This entry describes the device's pse
port mode.

Enumeration

Enumerated Values:

0	off
1	discovering
2	powered
3	fault
4	disabled
5	overcurrent
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.31.10.1.3

poepsePortMaxPower

This entry describes the permitted
power for this port in mW.

Integer32r/w

Constraints:
range: 0-15400

.1.3.6.1.4.1.3181.10.3.31.10.1.4

poepsePortMeasuredPower

This entry describes the measured
power for this port in mW.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.31.10.1.5

poepsePortMaxClass

This entry describes the maximnum
allowed poe class for this port.

Enumerationr/w

Enumerated Values:

0	class0
1	class1
2	class2
3	class3
4	class4
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.31.10.1.6

poepsePortDetectedClass

This entry describes the detected
poe class for this port.

Enumeration

Enumerated Values:

0	class0
1	class1
2	class2
3	class3
4	class4
254	undefined
255	unsupported

.1.3.6.1.4.1.3181.10.3.31.10.1.7

poepsePortMeasuredVoltage

This entry describes the measured
Voltage for this port in multiples
of 0.1V.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.3181.10.3.31.10.1.8