LUM-MULTIRATE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
1
Rows
1
Columns
75

mrtIfTable

table
.1.3.6.1.4.1.8708.2.12.2.2.1 · 1 row entry · 75 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk mrtIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-MULTIRATE-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-MULTIRATE-MIB::mrtIfTable' 
The interface list.
mrtIfEntry row .1.3.6.1.4.1.8708.2.12.2.2.1.1
An entry in the interface list.
Indexes
Column Syntax OID
mrtIfIndex
An arbitrary index assigned to each entry.
Unsigned32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.1
mrtIfName
The management name of the interface, for
example 'mrti1:2:1', where the first number
indicates sub-rack, the second slot number and
the third is the port number.
Examples:

mrti:s:s:p - Multirate client i…
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.2
mrtIfDescr
User configurable label.

This attribute can be written via SNMP.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.3
mrtIfSubrack
The number of the subrack where the interface
is located.
LUM-TCSubrackNumber
Type Constraints:
range: 0..15
Description:
The number of a subrack within a network element.

0 signifies an undefined subrack number.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.4
mrtIfSlot
The number of the slot where the interface is
located.
LUM-TCSlotNumber
Type Constraints:
range: 0..22
Description:
The number of a slot within a subrack.

0 signifies an undefined slot number.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.5
mrtIfTxPort
The number of the port where the TX-side of the
interface is located.
LUM-TCPortNumber
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.6
mrtIfRxPort
The number of the port where the RX-side of the
interface is located.
LUM-TCPortNumber
Type Constraints:
range: 0..116
Description:
The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.7
mrtIfInvPhysIndexOrZero
The row in the invPhysTable for this interface.
Set to 0 if not known.
Unsigned32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.8
mrtIfFormat
The expected signal format.

The default value is board dependent. For information
about the default value for this particular board,
please refer to the user manual.
LUM-TCSignalFormatr/w
Type Values:
1other
2stm1
3stm4
4stm16
5gbE
6stm64
7fc1Gb
8fc2Gb
9wan10GbE
10unused
11lan10GbE
12escon
13esconLL
14dvb270
15oc3
16oc12
17oc48
18oc192
19hdtv1485
20ethernet
21fastEthernet
22lan10GbEFec
23wan10GbEStm64Fec
24fc4Gb
25etr
26auto
27down
28stm1Oc3
29stm4Oc12
30stm16Oc48
31stm64Oc192
32gbe9Line
34ddgbeLine
35gbEorTrm5500
36fc8Gb
37otu2
38otu2e
39e1
40t1
41mbh2Gb5
42syncE
43line4G
44mbh4Gbps
45fecLan10GbE1A
46fecLan10GbE1B
47sdi3G
48iWdm4G
49sdSdi270
50hdtvNTSC
51oc768
52stm256
53lan40GbE
54wan40GbE
55sfStm256Oc768
56iwdm40Gb
57otu4
58lan100GbE
59transpLan10GbE
60cpri1
61cpri2
62cpri3
63cpri4
64cpri5
65cpri6
66cpri7
67fc10Gb
68fc16Gb
69cpri8
70obsai1x
71obsai2x
72obsai4x
73obsai8x
74otu1
75iwdm11G
76rw100G
77rw200G
78otu4SdFec
79otuj1
80otuj2
81fc32Gb
82clearChannel32GbFc
83lan400GbE
84flexO4
85flexO2
86openZRplus400
87openZRplus200
88lan25GbE
89otuC2
90otuC4
91otuC1i
92otuC2i
93otuC1ix2
94otuC4i
95otuC1ix4
2147483647notApplicable
Description:
Signal format for an interfaces.

other - Unspecified format (see bitrate configuration
for speed)

stm1 - STM-1 SDH signal

stm4 - STM-4 SDH signal

stm16 - STM-16 SDH signal
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.9
mrtIfHighSpeed
The expected signal bit rate in units of
1,000,000 bits (Mb) per second. If this object
reports a value of 'n' then the speed of the
interface is somewhere in the range of 'n-500,000'
to 'n+499,999'.
SNMPv2-SMIGauge32r/w
Constraints:
range: 125-2500
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.10
mrtIfHighSpeedMin
The minmum speed in units of 1,000,000 bits (Mb)
per second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+499,999'.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.11
mrtIfHighSpeedMax
The maximum speed in units of 1,000,000 bits per
second. If this object reports a value of 'n'
then the speed of the interface is somewhere in
the range of 'n-500,000' to 'n+499,999'.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.12
mrtIfPowerLevel
The received power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.13
mrtIfPowerLevelHighThreshold
The upper threshold for received power level in
units of 0.1 dBm.

Note: Depending on the type of board and interface
the value range may vary. The 'stm4' and 'stm1'
ranges are applicable for muxponder int…
Integer32r/w
Constraints:
range: -280-0
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.14
mrtIfPowerLevelLowThreshold
The lower threshold for received power level in
units of 0.1 dBm.

Note: Depending on the type of board and interface
the value range may vary. The 'stm4' and 'stm1'
ranges are applicable for muxponder int…
Integer32r/w
Constraints:
range: -280-0
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.15
mrtIfLaserStatus
The operational state of the laser.

off - The laser is turned off.

on - The laser is turned on.
Enumeration
Enumerated Values:
1off
2on
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.16
mrtIfAdminStatus
The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…
LUM-TCBoardOrInterfaceAdminStatusr/w
Type Values:
1down
2service
3up
Description:
The administrative state for a board or
interface.

down - The board/interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
servi…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.17
mrtIfOperStatus
The operational state for the interface.

notPresent - The physical resources are not
available.

down - The interface is de-activated or the are
faults preventing it from going to the
'up'-s…
LUM-TCBoardOrInterfaceOperStatus
Type Values:
1notPresent
2down
3up
Description:
The operational state for a board or interface.

notPresent - The board/interface is not available.

down - The board/interface is de-activated or
there are faults preventing it from going to the
'up…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.18
mrtIfLossOfSignal
Loss of signal.
Applicable for all signal formats.

A(ctivation): Active loss of signal HW
indication.

D(e-activation): Inactive loss of signal HW
indication.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.19
mrtIfReceivedPowerHigh
Received power level is too high.
Applicable for all signal formats.

A: The received power level exceeds the
the built-in overload threshold.

D: The received power level is 0.5 dB below the…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.20
mrtIfReceivedPowerLow
Received power level low threshold exceeded.
Applicable for all signal formats.

A: The received power level is below the
associated threshold.

D: The received power level is 0.5 dB above th…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.21
mrtIfLaserBiasHigh
Laser bias high threshold exceeded.

A: The laser bias current exceeds the
associated threshold.

D: The laser bias current is 0.5 mA below the
associated threshold.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.22
mrtIfErroredSecondsdeprecated
Note: This attribute is deprecated!

Errored seconds threshold exceeded.

A: The number of errored seconds (ES) during a
period exceeds the associated threshold.

D: At the star…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.23
mrtIfSeverelyErroredSecondsdeprecated
Note: This attribute is deprecated!

Severely errored seconds (SES) threshold exceeded.

A: The number of severely errored seconds during a period
exceeds the associated threshold.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.24
mrtIfBackgroundBlockErrorsdeprecated
Note: This attribute is deprecated!

Background block errors (BBE) threshold exceeded.

A: The number of errors during a period
exceeds the associated threshold.

D: At the star…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.25
mrtIfUnavailableSecondsdeprecated
Note: This attribute is deprecated!

Unavailable seconds (UAS) threshold exceeded.

A: The number of unavailable seconds during a period
exceeds the associated threshold.

D: At…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.26
mrtIfLossOfFrame
Loss of frame.
Applicable for SDH/Sonet signal formats.

A: SDH frame can not be located.

D: SDH frame is located.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.27
mrtIfMsAlarmIndicationSignalC2W
MS Alarm indication signal (MS-AIS) on the
client side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.28
mrtIfRemoteDefectIndication
Remote defect indication.
Applicable for SDH/Sonet signal formats.

A: RDI indication (in SDH frame) active.

D: RDI indication inactive.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.29
mrtIfLossOfSync
Loss of sync (GbE).
Applicable for GbE signal formats.

A: GbE 'frame' can not be located.

D: GbE 'frame' is located.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.30
mrtIfBitrateMismatch
Bitrate mismatch (Other).
Applicable for other signal formats.

D: The interface is unable to lock to the
inserted signal.

D: The interface is able to lock to the
inserted signal.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.31
mrtIfLaserBias
Measures laser bias current value in tenths of
mA (0.1 mA).
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.32
mrtIfLaserBiasThreshold
Sets the threshold for the laser bias alarm.
in percentage relative to the value set during
production.
The preset value is 100%.
Unsigned32r/w
Constraints:
range: 0-300
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.33
mrtIfJ0PathTrace
The recevied J0 path trace string.
Applicable for SDH/Sonet signal formats.
OctetString
Constraints:
range: 1-1
range: 16-16
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.34
mrtIfAuAlarmIndicationSignalW2C
Alarm indication signal (AIS) on the trunk-side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.35
mrtIfAuLossOfPointerW2C
Loss of pointer detected on the trunk-side.
Applicable for SDH/Sonet signal formats.

A: A loss of pointer is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.36
mrtIfTxSignalStatus
The operational state for outgoing (TX) signal
of the interface.

down - A fault that would lead to a protection
switch has occurred.

degraded - The signal quality is impaired.
…
Enumeration
Enumerated Values:
1down
2degraded
3up
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.37
mrtIfTruncVc4
States which VC4 in the STM-16 frame that the
interface is connected to.

0 means unconnected, i.e. the signal passes
through. (This may cause a loop depending on
network topology.)

For …
Unsigned32r/w
Constraints:
range: 0-16
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.38
mrtIfAuAlarmIndicationSignalC2W
Alarm indication signal (AIS) on the
client-side.
Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.39
mrtIfAuLossOfPointerC2W
Loss of pointer detected on the client-side.
Applicable for SDH/Sonet signal formats.

A: A loss of pointer is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.40
mrtIfTraceIntrusionMode
Indicates wether the trace identifier should be
inserted in the transmitted signal.

disabled - The trace identifier is taken from
the recevied signal if possible.

enabled - The trace ident…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.41
mrtIfTraceTransmitted
The trace identifier to be transmitted from this
interface.

Set to empty string for default value:

<IP address>:<subrack>:<slot>:<port>

Note that only the last part of the ad…
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-15
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.42
mrtIfTraceReceived
The received trace identifier for this interface.
SNMPv2-TCDisplayString
Constraints:
range: 0-15
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.43
mrtIfTraceExpected
Trace identifier used for matching against
the received trace identifier.
SNMPv2-TCDisplayStringr/w
Constraints:
range: 0-15
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.44
mrtIfTraceAlarmMode
Controls if the trace identifier mismatch alarm
should be raised.

disabled - The alarm is disabled.

enabled - The alarm is raised if expected trace
identifier differs from the received trac…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.45
mrtIfTraceMismatch
Indicates if the expected trace identifier
differs from the received trace identifier.

A: The received trace identifier differs from
the expected trace identifier.

D: The identifiers match.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.46
mrtIfTruncVc4Statusdeprecated
Shows the status of the VC4(s) that this port is
connected to.

undefined - used when the port is not connected
to any VC4. Also used when an STM4 port is VC4s
that have conflicting modes.
…
Enumeration
Enumerated Values:
0undefined
1addDrop
2passThrough
3unconnected
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.47
mrtIfMsAlarmIndicationSignalW2C
MS Alarm indication signal (MS-AIS) on the trunc
side. Applicable for SDH/Sonet signal formats.

A: An 'all ones' SDH signal is detected.

D: SDH signal recovered.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.48
mrtIfForwardAls
Forward Automatic Laser Shut-down. Decides the
behaviour of the client laser (W2C) when the
trunc signal is defected.

disabled - The laser is NOT turned off at failure.

enabled - The laser …
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.49
mrtIfSuppressRemoteAlarms
Suppress AIS and RDI in the alarm list.
The fault status on the port object can, however,
be seen.

disabled - alarms are not suppressed.

enabled - alarms are suppressed.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.50
mrtIfConfigurationCommand
Command to change the signal format and,
if applicable, also the speed.

Synopsis: configure [<format> [<speed>]]

If no arguments are given, the user will be prompted.

tpQMr, …
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.51
mrtIfTrxCodeMismatch
The inserted transceiver does not have a legal
manufacturer code.

A: A transceiver with illegal code is inserted.

D: The transceiver with illegal code is removed.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.52
mrtIfTrxBitrateUnavailable
The inserted transceiver does not support the requested
bit rate.

A: A transceiver with other supported bit rate than
the requested bit rate is inserted.

D: The transceiver with the non-…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.53
mrtIfTrxMissing
An expected transceiver is missing.

A: An expected transceiver is missing.

D: The missing transceiver is inserted.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.54
mrtIfTrxClass
String that describes the transceiver class.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.55
mrtIfEntityId
Index in entity table.

-- Only used for notifications
Unsigned32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.56
mrtIfTransmitterFailed
The transceiver HW has detected a failure
in the transmitter part.

A: The transmitter has failed

D: The transmitter is OK again
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.57
mrtIfReceiverSensitivity
The lowest power that the receiver is guaranteed
to handle, in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.58
mrtIfPowerLevelLowRelativeThreshold
The lower threshold for received power level in
units of 0.1 dB, relative to the receiver
sensitivity.
Integer32r/w
Constraints:
range: -50-100
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.59
mrtIfFarEndLoopback
Loop the client TX signal back to the client RX.

disabled - the signal is not looped

enabled - the signal is looped.
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.60
mrtIfConfigureModeCommand
Command to change the TRX mode: CLIENT or LINE.
Also select the TRX media.

Synopsis: configureMode [<trxMode>] [<trxMedia>]

If no arguments are given, the user will be prompted.
LUM-TCCommandString
Description:
tbd
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.61
mrtIfTrxMode
Shows if the port is configured as:

- normal CLIENT interface connected to non-Transmode
or non-Infinera client equipment, with non-colored,
or colored TRXes.

- a LINE interface connect…
Enumerationr/w
Enumerated Values:
1client
2line
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.62
mrtIfExpectedTxFrequency
The expected frequency given in hundreds of GHz
(0.01 GHz).
LUM-TCLambdaFrequencyr/w
Type Values:
0undefined
1iWdmPonFrequency
2otclg
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
1611w1611
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.63
mrtIfTxFrequency
The transmitted frequency given in hundreds of
GHz (0.01 GHz).
LUM-TCLambdaFrequency
Type Values:
0undefined
1iWdmPonFrequency
2otclg
130b1300
150b1500
850w850
1270w1270
1290w1290
1310w1310
1330w1330
1350w1350
1370w1370
1390w1390
1410w1410
1430w1430
1450w1450
1470w1470
1490w1490
1510w1510
1530w1530
1550w1550
1570w1570
1590w1590
1610w1610
1611w1611
18710ch871
18730ch873
18750ch875
18770ch877
18790ch879
18810ch881
18830ch883
18850ch885
18870ch887
18890ch889
18910ch891
18930ch893
18950ch895
18970ch897
18990ch899
19010ch901
19030ch903
19050ch905
19070ch907
19090ch909
19135ch9135
19140ch914
19145ch9145
19150ch915
19155ch9155
19160ch916
19165ch9165
19170ch917
19175ch9175
19180ch918
19185ch9185
19190ch919
19195ch9195
19200ch920
19205ch9205
19210ch921
19215ch9215
19220ch922
19225ch9225
19230ch923
19235ch9235
19240ch924
19245ch9245
19250ch925
19255ch9255
19260ch926
19265ch9265
19270ch927
19275ch9275
19280ch928
19285ch9285
19290ch929
19295ch9295
19300ch930
19305ch9305
19310ch931
19315ch9315
19320ch932
19325ch9325
19330ch933
19335ch9335
19340ch934
19345ch9345
19350ch935
19355ch9355
19360ch936
19365ch9365
19370ch937
19375ch9375
19380ch938
19385ch9385
19390ch939
19395ch9395
19400ch940
19405ch9405
19410ch941
19415ch9415
19420ch942
19425ch9425
19430ch943
19435ch9435
19440ch944
19445ch9445
19450ch945
19455ch9455
19460ch946
19465ch9465
19470ch947
19475ch9475
19480ch948
19485ch9485
19490ch949
19495ch9495
19500ch950
19505ch9505
19510ch951
19515ch9515
19520ch952
19525ch9525
19530ch953
19535ch9535
19540ch954
19545ch9545
19550ch955
19555ch9555
19560ch956
19565ch9565
19570ch957
19575ch9575
19580ch958
19585ch9585
19590ch959
19595ch9595
19600ch960
19605ch9605
19610ch961
Description:
The frequency of the 'wavelength' given in hundreds
of GHz (0.01 GHz).
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.64
mrtIfUnexpectedTxFrequency
The actual frequency does not match the
pre-configured frequency.

A pre-configured frequency of '0' matches
all actual frequencies.

A: The configured frequency does not match the
actual fre…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.65
mrtIfIllegalFrequency
The frequency supported by the transceiver is not
recognized by the system.

A: Invalid or unknown frequency information is
detected in the (pluggable) transceiver or
board production data.
…
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.66
mrtIfTrxMedia
Defines the media and capability of the TRX.
LUM-TCTrxMediar/w
Type Values:
0undefined
1optical
2tp1000BaseT
3tp100BaseT
4tp10BaseT
5electrical
Description:
Defines the media and capability of the TRX

optical - Optical media

tp1000BaseT - Twisted-pair capable of 1000BaseT

tp100BaseT - Twisted-pair capable of 100BaseT

tp1…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.67
mrtIfTrxMediaMismatch
The TRX media does not match the expected one.

A: Invalid or mismatching trx media is
detected.

D: The (pluggable) transceiver or board is
replaced, or the configuration is changed.
LUM-TCFaultStatus
Type Values:
1ok
2alarm
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.68
mrtIfLaserForcedOn
When enabled, the laser is on regardless of whether
there is a trunc signal present or not.

disabled - the laser is only on when there is a
trunc signal.

enabled - the laser is a…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.69
mrtIfTruncAutoNegotiationMode
Decides whether auto negotiation shall
be performed over the trunc connection.

This is applicable when the terminating
node at the other side of the
trunc is configured as follows:

- it h…
Enumerationr/w
Enumerated Values:
1disabled
2enabled
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.70
mrtIfObjectProperty
Property mask.
LUM-TCObjectProperty
Type Constraints:
range: 0..4294967295
Description:
A bitmask of length 32 encoding certain properties
of an object.
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.71
mrtIfTxPowerLevel
The transmitted power level in units of 0.1 dBm.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.72
mrtIfLaserTempActual
The actual laser temperature in units of
0.1 degrees centigrade.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.73
mrtIfHighSpeed2
The expected signal bit rate in units of
1,000,000 bits (Mb) per second.
The value is given with 2 decimals,
so the resolution is 10 000 bits per second.
SNMPv2-SMIGauge32r/w
Constraints:
range: 12500-250000
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.74
mrtIfRxSignalStatus
The operational state for incoming (RX) signal
of the interface.

down - A fault that would lead to a protection
switch has occurred.

degraded - The signal quality is impaired.
…
Enumeration
Enumerated Values:
1down
2degraded
3up
 .1.3.6.1.4.1.8708.2.12.2.2.1.1.75