Juniper-PPPOE-MIB Table View

The parameters for the PPPoE service on this interface.

juniPPPoEIfEntry row .1.3.6.1.4.1.4874.2.2.18.1.1.2.1

The Parameters for a particular PPPoE interface.

Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable, and
juniPPPoEIfStatsTable.

Indexes

juniPPPoEIfIfIndex

Column	Syntax	OID
juniPPPoEIfIfIndex The ifIndex value of the corresponding ifEntry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.1
juniPPPoEIfMaxNumSessions The number of sessions allowed on the PPPoE interface, zero indicates unlimited.	Integer32r/w Constraints: range: 0-65335	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.2
juniPPPoEIfRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.3
juniPPPoEIfLowerIfIndex The ifIndex of an interface over which this PPPoE interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.4
juniPPPoEIfAcName The name to use for the AC-NAME tag that is sent in any PADO that is sent on this interface.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.5
juniPPPoEIfDupProtect Flag to allow duplicate MAC addresses.	Juniper-TCJuniEnabler/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.6
juniPPPoEIfPADIFlag This flag controls whether we always respond to a PADI with a PADO regardless of the ability to create the session and allows the session establish phase to resolve it.	Juniper-TCJuniEnabler/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.7
juniPPPoEIfAutoconfig This flags determines whether the upper PPPoE interface is created dynamically or statically. When enable(1) the interface is created dynamically.	Juniper-TCJuniEnabler/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.8
juniPPPoEIfServiceNameTable Associate a PPPoE Service Name Table with this interface for PADI processing.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.9
juniPPPoEIfPadrRemoteCircuitIdCapture This flags determines whether the remote circuit id string will be captured and subsequently used as the NAS-PORT-ID radius attribute when it arrives as a tag in the PADR packet.	Juniper-TCJuniEnabler/w Type Values: 0 disable 1 enable	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.10
juniPPPoEIfMtu The initial Maximum Transmit Unit (MTU) that the PPPoE major interface entity will advertise to the remote entity. If the value of this variable is 1 then the local PPPoE entity will use an MTU value dete…	Integer32r/w Constraints: range: 66-65535 range: 1-2	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.11
juniPPPoEIfLockoutMin The lower bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if juniPPPoEIfAutoconfig is set for this in…	Integer32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.12
juniPPPoEIfLockoutMax The upper bound, in seconds, of the time range used to specify the duration of the lockout of the client from recognition for the specified interface. This only takes effect if juniPPPoEIfAutoconfig is set for this in…	Integer32r/w Constraints: range: 0-86400	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.13
juniPPPoEMaxSessionVsa Configure the action to be taken by PPPoE when RADIUS server returns the PPPoE max-session value: override Override the current PPPoE max-session value with the value returned by RADIUS server. Ignore …	Enumerationr/w Enumerated Values: 1 override 2 ignore	.1.3.6.1.4.1.4874.2.2.18.1.1.2.1.14

The statistics for the PPP over Ethernet Interface for the PPPoE
service on this interface.

juniPPPoEIfStatsEntry row .1.3.6.1.4.1.4874.2.2.18.1.1.3.1

The statistics for a particular PPPoE Interface.

Indexes

juniPPPoEIfIfIndex

Column	Syntax	OID
juniPPPoEIfStatsRxPADI Number of PADI packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.1
juniPPPoEIfStatsTxPADO Number of PADO packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.2
juniPPPoEIfStatsRxPADR Number of PADR packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.3
juniPPPoEIfStatsTxPADS Number of PADS packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.4
juniPPPoEIfStatsRxPADT Number of PADT packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.5
juniPPPoEIfStatsTxPADT Number of PADT packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.6
juniPPPoEIfStatsRxInvVersion Number of packets received with invalid version.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.7
juniPPPoEIfStatsRxInvCode Number of packets received with invalid code.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.8
juniPPPoEIfStatsRxInvTags Number of packets received with invalid tags.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.9
juniPPPoEIfStatsRxInvSessionobsolete Number of packets received with invalid session identifiers. This object became obsolete when separate counters were added for PADI and PADR packets.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.10
juniPPPoEIfStatsRxInvTypes Number of packets received with invalid types.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.11
juniPPPoEIfStatsRxInvPackets Number of invalid packets received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.12
juniPPPoEIfStatsRxInsufficientResources Number of session requests that could not be honored due to invalid resources.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.13
juniPPPoEIfStatsTxPADM Number of PADM packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.14
juniPPPoEIfStatsTxPADN Number of PADN packets transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.15
juniPPPoEIfStatsRxInvTagLength Number of packets received with invalid tag length.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.16
juniPPPoEIfStatsRxInvLength Number of packets received with invalid length.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.17
juniPPPoEIfStatsRxInvPadISession Number of PADI packets received with invalid session identifiers.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.18
juniPPPoEIfStatsRxInvPadRSession Number of PADR packets received with invalid session identifiers.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.1.3.1.19

The lockout configuration and state of a PPPoE client on this interface.

juniPPPoEIfLockoutEntry row .1.3.6.1.4.1.4874.2.2.18.1.1.4.1

Each entry contains the configuration and state of a particular
PPPoE interface client lockout.

Indexes

juniPPPoEIfIfIndex juniPPPoEIfLockoutClientAddress

Column	Syntax	OID
juniPPPoEIfLockoutClientAddress The source MAC address if the client.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4874.2.2.18.1.1.4.1.1
juniPPPoEIfLockoutTime The time duration, in seconds, currently used to lockout the specified encapsulation type from recognition for the specified interface. The reported value is within the range specified by juniPPPoEIfLockoutMin and juni…	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.4874.2.2.18.1.1.4.1.2
juniPPPoEIfLockoutElapsedTime The elapsed time, in seconds, that the specified encapsulation type has been locked-out from recognition for the specified interface. Its value will not exceed that of juniPPPoEIfLockoutTime. A value of 0 indicates t…	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.4874.2.2.18.1.1.4.1.3
juniPPPoEIfLockoutNextTime The time duration, in seconds, that will be used to lockout the specified encapsulation type from recognition for the specified interface for the next event that results in a lockout condition. The reported value is wi…	Integer32 Constraints: range: 0-86400	.1.3.6.1.4.1.4874.2.2.18.1.1.4.1.4

This table contains entries for PPPoE Subinterfaces present in the
system.

juniPPPoESubIfEntry row .1.3.6.1.4.1.4874.2.2.18.1.2.2.1

Each entry describes the characteristics of a PPPoE Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created /deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniPPPoESubIfIndex

Column	Syntax	OID
juniPPPoESubIfIndex The ifIndex of the PPPoE Subinterface. When creating entries in this table, suitable values for this object are determined by reading juniPPPoESubNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.1
juniPPPoESubIfRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.2
juniPPPoESubIfLowerIfIndex The ifIndex of a PPPoE interface over which this PPPoE Subinterface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.3
juniPPPoESubIfId An integer identifier for the PPPoE subinterface, used in conjunction with the command-line interface. It is provided here for cross-reference purposes only. The value must be unique among subinterfaces …	Integer32r/w Constraints: range: -1-2147483647	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.4
juniPPPoESubIfSessionId The current sessionId associated with this sub-interface.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.5
juniPPPoESubIfMotm A message to send via a PADM on the sub-interface when the sub-interface transitions to the ifOperStatusUp state. The client may choose to display this message to the user.	OctetStringr/w Constraints: range: 0-127	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.6
juniPPPoESubIfUrl A URL to be sent via a PADM on the sub-interface when the sub-interface transitions to the ifOperStatusUp state. The client may use this URL as the initial web-page for the user.	OctetStringr/w Constraints: range: 0-127	.1.3.6.1.4.1.4874.2.2.18.1.2.2.1.7

This table contains entries for the PPPoE Service-name tables.

juniPPPoEServiceNameTableEntry row .1.3.6.1.4.1.4874.2.2.18.1.6.2.1

The parameters for the PPPoE service-name table.

Indexes

juniPPPoEServiceNameTableIndex

Column	Syntax	OID
juniPPPoEServiceNameTableIndex The index value of the Service-name Table Entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.18.1.6.2.1.1
juniPPPoEServiceNameTableName Service-name table name.	OctetStringr/w Constraints: range: 0-31	.1.3.6.1.4.1.4874.2.2.18.1.6.2.1.2
juniPPPoEServiceNameTableEmptyAction Identifies the behavior when the empty (zero length) Service-name tag is received in a PADI frame.	JuniPPPoEServiceNameActionr/w Type Values: 0 drop 1 terminate	.1.3.6.1.4.1.4874.2.2.18.1.6.2.1.3
juniPPPoEServiceNameTableRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.18.1.6.2.1.4
juniPPPoEServiceNameTableUnknownAction Identifies the behavior when the unknown (unconfigured) Service-name tag is received in a PADI frame.	JuniPPPoEServiceNameActionr/w Type Values: 0 drop 1 terminate	.1.3.6.1.4.1.4874.2.2.18.1.6.2.1.5

This table contains entries for the PPPoE Service-names.

juniPPPoEServiceNameEntry row .1.3.6.1.4.1.4874.2.2.18.1.6.3.1

The parameters for the PPPoE service-name table entry.

Indexes

juniPPPoEServiceNameTableIndex juniPPPoEServiceName

Column	Syntax	OID
juniPPPoEServiceName Service-name tag value.	OctetString Constraints: range: 0-31	.1.3.6.1.4.1.4874.2.2.18.1.6.3.1.1
juniPPPoEServiceNameAction Identifies the behavior when the Service-name tag is received in a PADI/PADR frame.	JuniPPPoEServiceNameActionr/w Type Values: 0 drop 1 terminate	.1.3.6.1.4.1.4874.2.2.18.1.6.3.1.2
juniPPPoEServiceNameRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.18.1.6.3.1.3