ibrary TapeAlert 001.
Flag: Library hardware A
Type: C
Cause: The changer mechanism is having trouble communicating with the
       internal drive.
Required host message:
The library is having difficulty communicating with the drive.
1. Restart the operation.
2. If the problem persists, call your IBM Service Representative.

ibrary TapeAlert 010.
Flag: Library temperature limits.
Type: C
Cause: Library temperature limits exceeded.
Required host message:
General environmental conditions inside the library have exceeded
the specified temperature range.

ibrary TapeAlert 011.
Flag: Library voltage limits.
Type: C
Cause: Library voltage limits exceeded.
Required host message:
A potential failure of a power supply exists. Call your IBM Service Representative.

ibrary TapeAlert 012.
Flag: Library stray tape.
Type: C
Cause: Stray cartridge left in library drive after previous error
       recovery.
Required host message:
A cartridge has been left in a drive inside the library by a previous
hardware fault:
1. Insert an empty magazine to clear the fault.
2. If the fault does not clear, turn the library off and then on again.
3. If the problem persists, call the library supplier helpline.

ibrary TapeAlert 013.
Flag: Library pick retry.
Type: W
Cause: Operation to pick a cartridge from a slot had to perform an
       excessive number of retries before succeeding.
Required host message:
There is a potential problem with a drive ejecting cartridges short
or with the library mechanism picking a cartridge from a slot.
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline.

ibrary TapeAlert 014.
Flag: Library place retry.
Type: W
Cause: Operation to place a cartridge into a slot had to perform an
       excessive number of retries before succeeding.
Required host message:
There is a potential problem with the library mechanism placing a
cartridge into a slot:
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline.

ibrary TapeAlert 015.
Flag: Library load retry.
Type: W
Cause: Operation to load a cartridge into a drive had to perform an
       excessive number of retries before succeeding.
Required host message:
There is a potential problem with the library mechanism placing a
cartridge into a slot:
1. No action needs to be taken at this time.
2. If the problem persists, call the library supplier helpline.

ibrary TapeAlert 016.
Flag: Library door.
Type: C
Cause: Changer door open prevents library functioning.
Required host message:
A library door is open and prevents the library from functioning.
1. Clear any obstructions from the library door.
2. Close the library door.

ibrary TapeAlert 017.
Flag: Library mail slot.
Type: C
Cause: Mechanical problem with import/export mail slot.
Required host message:
A problem with an I/O station exists.
1. Ensure that there is no obstruction in the I/O station.
2. Restart the operation.
3. If the problem persists, call your IBM Service Representative.

ibrary TapeAlert 018.
Flag: Library magazine.
Type: C
Cause: Library magazine not present.
Required host message:
The library cannot operate without the magazine.
1. Insert the magazine into the library.
2. Restart the operation.

ibrary TapeAlert 019.
Flag: Library security mode.
Type: W
Cause: Library door opened then closed during operation.
Required host message:
Library security has been compromised.

ibrary TapeAlert 002.
Flag: Library hardware B.
Type: W
Cause: The changer mechanism has a hardware fault.
Required host message:
The library has a hardware failure.
1. Restart the operation.
2. If the problem persists, call your IBM Service Representative.

ibrary TapeAlert 020.
Flag: Library security mode.
Type: I
Cause: Library security mode has changed.
Required host message:
The security mode of the library has been changed. Either the library
has been put into secure mode or the library has exited secure mode.
This is for informational purposes only. No action is required.

rive TapeAlert 001.
Flag: Read warning.
Type: W
Cause: The drive is having severe trouble reading.
Required host message:
The tape drive is having problems reading data. No data has been
lost, but there has been a reduction in the performance of the
tape.

rive TapeAlert 002.
Flag: Write warning.
Type: W
Cause: The drive is having severe trouble writing.
Required host message:
The tape drive is having problems writing data. No data has been lost,
but there has been a reduction in the performance of the tape.

rive TapeAlert 003.
Flag: Hard error.
Type: W
Cause: The drive had a hard read or write error.
Required host message:
The operation has stopped because an error has occurred while reading
or writing data which the drive cannot correct.

rive TapeAlert 004.
Flag: Media.
Type: C
Cause: Media can no longer be written/read, or performance is severely
       degraded.
Required host message:
Unrecoverable read, write, or positioning error that is due to a faulty tape cartridge. Replace the tape cartridge.

rive TapeAlert 005.
Flag: Read failure.
Type: C
Cause: The drive can no longer read data from the tape.
Required host message:
The tape is damaged or the drive is faulty. Call the tape drive supplier
helpline.

rive TapeAlert 006.
Flag: Write failure.
Type: C
Cause: The drive can no longer write data to the tape.
Required host message:
The tape is from a faulty batch or the tape drive is faulty.
1. Use a good tape to test the drive.
2. If the problem persists, call the tape drive supplier helpline.

rive TapeAlert 007.
Flag: Media life.
Type: W
Cause: The media has exceeded its specified life.
Required host message:
The tape cartridge has reached the end of its calculated useful life:
1. Copy any data you need to another tape.
2. Discard the old tape.

rive TapeAlert 008.
Flag: Not data grade.
Type: W
Cause: The drive has not been able to read the MRS stripes.
Required host message:
The cartridge is not data-grade.  Any data that you write to the tape is at risk.
Replace the tape with a data-grade tape.

rive TapeAlert 009.
Flag: Write protect.
Type: C
Cause: Write command is attempted to a write protected tape.
Required host message:
You are trying to write to a write-protected cartridge. Remove the
write-protection or use another tape.

ibrary TapeAlert 021.
Flag: Library offline.
Type: I
Cause: Library manually turned offline.
Required host message:
The library has been manually turned offline and is unavailable for use.

rive TapeAlert 010.
Flag: No removal.
Type: I
Cause: Manual or s/w unload attempted when prevent media removal on.
Required host message:
The tape drive received an UNLOAD command after the server prevented
the tape cartridge from being removed. Refer to the documentation for
your server's operating system.

rive TapeAlert 011.
Flag: Cleaning media.
Type: I
Cause: Cleaning tape loaded into drive.
Required host message:
The tape in the drive is a cleaning cartridge.

rive TapeAlert 012.
Flag: Unsupported format.
Type: I
Cause: Attempted load of unsupported tape format, eg DDS2 in DDS1 drive.
Required host message:
You have tried to load a cartridge of a type which is not supported by
the drive.

rive TapeAlert 013.
Flag: Recoverable snapped tape.
Type: C
Cause: Tape snapped/cut in the drive where media can be ejected.
Required host message:
The tape has split apart. Do not attempt to extract the old tape cartridge.
Call your IBM Service Representative.

rive TapeAlert 014.
Flag: Unrecoverable snapped tape.
Type: C
Cause: Tape snapped/cut in the drive where media cannot be ejected.
Required host message:
The operation has failed because the tape in the drive has snapped:
1. Do not attempt to extract the tape cartridge.
2. Call the tape drive supplier helpline.

rive TapeAlert 015.
Flag: Memory chip in cartridge failure.
Type: W
Cause: Memory chip failed in cartridge.
Required host message:
The memory in the tape cartridge has failed, which reduces performance. Replace the tape cartridge.
If this error occurs on multiple cartridges, see Error Code 6 located in the list of drive error
codes in the 3584 Maintenance Information Guide.

rive TapeAlert 016.
Flag: Forced eject.
Type: C
Cause: Manual or forced eject while drive actively writing or reading.
Required host message:
The operation has failed because the tape cartridge was manually ejected
while the tape drive was actively writing or reading.

rive TapeAlert 017.
Flag: Read only format.
Type: W
Cause: Media loaded that is read-only format.
Required host message:
You have loaded a cartridge of a type that is read-only in this drive.
The cartridge will appear as write-protected.

rive TapeAlert 018.
Flag: Tape directory corrupted on load.
Type: W
Cause: Tape drive powered down with tape loaded, or permanent error
       prevented the tape directory being updated.
Required host message:
The drive detected that the tape directory in the cartridge memory has been
corrupted.  Re-read all data from the tape to rebuild the tape directory.

rive TapeAlert 019.
Flag: Nearing media life.
Type: I
Cause: Media may have exceeded its specified number of passes.
Required host message:
The tape cartridge is nearing the end of its calculated life. It is
recommended that you:
1. Use another cartridge for your next backup.
2. Store this cartridge in a safe place in case you need to restore
   data from it.

ibrary TapeAlert 022.
Flag: Library drive offline.
Type: I
Cause: Library turned internal drive offline.
Required host message:
A drive inside the library has been taken offline. This is for
informational purposes only. No action is required.

rive TapeAlert 020.
Flag: Clean now.
Type: C
Cause: The drive thinks it has a head clog, or needs cleaning.
Required host message:
The tape drive needs cleaning:
1. If the operation has stopped, eject the tape and clean the drive.
2. If the operation has not stopped, wait for it to finish and then clean
   the drive.
Check the tape drive users manual for device specific cleaning
instructions.

rive TapeAlert 021.
Flag: Clean periodic.
Type: W
Cause: The drive is ready for a periodic clean
Required host message:
The tape drive is due for routine cleaning:
1. Wait for the current operation to finish.
2. Then use a cleaning cartridge.
Check the tape drive users manual for device specific cleaning
instructions.

rive TapeAlert 022.
Flag: Expired cleaning media.
Type: C
Cause: The cleaning tape has expired.
Required host message:
The last cleaning cartridge used in the tape drive has worn out:
1. Discard the worn out cleaning cartridge.
2. Wait for the current operation to finish.
3. Then use a new cleaning cartridge.

rive TapeAlert 023.
Flag: Invalid cleaning tape.
Type: C
Cause: Invalid cleaning tape type used.
Required host message:
The last cleaning cartridge used in the tape drive was an invalid type:
1. Do not use this cleaning cartridge in this drive.
2. Wait for the current operation to finish.
3. Then use a valid cleaning cartridge.

rive TapeAlert 024.
Flag: Retention requested.
Type: W
Cause: The drive is having severe trouble reading or writing, which
       will be resolved by a retention cycle.
Required host message:
The tape drive has requested a retention operation.

rive TapeAlert 025.
Flag: Dual-port interface error.
Type: W
Cause: Failure of one interface port in a dual-port configuration, eg
       Fibrechannel.
Required host message:
A redundant interface port on the tape drive has failed.

rive TapeAlert 026.
Flag: Cooling fan failure.
Type: W
Cause: Fan failure inside tape drive mechanism or tape drive enclosure.
Required host message:
A tape drive cooling fan has failed.

rive TapeAlert 027.
Flag: Power supply.
Type: W
Cause: Redundant PSU failure inside the tape drive enclosure or rack
       subsystem.
Required host message:
A redundant power supply has failed inside the tape drive enclosure.
Check the enclosure users manual for instructions on replacing the
failed power supply.

rive TapeAlert 028.
Flag: Power consumption.
Type: W
Cause: Power consumption of the tape drive is outside specified range.
Required host message:
The tape drive power consumption is outside the specified range.

rive TapeAlert 029.
Flag: Drive maintenance.
Type: W
Cause: The drive requires preventative maintenance (not cleaning).
Required host message:
Preventative maintenance of the tape drive is required. Check the
tape drive users manual for device specific preventative maintenance
tasks or call the tape drive supplier helpline.

ibrary TapeAlert 023.
Flag: Library scan retry.
Type: W
Cause: Operation to scan the barcode on a cartridge had to perform an
       excessive number of retries before succeeding.
Required host message:
There is a potential problem with the barcode label or the scanner hardware in the library mechanism.
1. Check for damaged, misaligned, or peeling barcode labels on cartridges.
2. If the problem persists, call your IBM Service Representative.

rive TapeAlert 030.
Flag: Hardware A.
Type: C
Cause: The drive has a hardware fault that requires reset to recover.
Required host message:
A hardware failure has occurred that requires a tape drive reset to recover.
If resetting the drive does not recover the error note the single-character
display and see the list of drive error codes in the 3584 Maintenance Information.

rive TapeAlert 031.
Flag: Hardware B.
Type: C
Cause: The drive has a hardware fault which is not read/write related
       or requires a power cycle to recover.
Required host message:
The tape drive failed it's internal Power-On Self Test.  Note the
single-character display and see the list of drive error codes in
the 3584 Maintenance Information.

rive TapeAlert 032.
Flag: Interface.
Type: W
Cause: The drive has identified an interfacing fault.
Required host message:
The tape drive has detected a problem with the SCSI,
Fibre or RS-422 interface. See Error Code 8 or 9
located in the list of drive error codes in the 3584
Maintenance Information.

rive TapeAlert 033.
Flag: Eject media.
Type: C
Cause: Error recovery action.
Required host message:
A failure has occurred that requires you to unload
the cartridge from the drive. Unload the tape cartridge,
the reinsert it and restart the operation.

rive TapeAlert 034.
Flag: Download failed.
Type: W
Cause: Firmware download failed.
Required host message:
The firmware download has failed because you have tried to use the
incorrect firmware for this tape drive. Obtain the correct firmware
and try again.

rive TapeAlert 035.
Flag: Drive humidity.
Type: W
Cause: Drive humidity limits exceeded.
Required host message:
Environmental conditions inside the tape drive are outside the specified
humidity range.

rive TapeAlert 036.
Flag: Drive temperature.
Type: W
Cause: Drive temperature limits exceeded.
Required host message:
The drive detected the temperature is exceeding the recommended temperature
of the library. See Error Code 1 in the list of drive error codes in the
3584 Maintenance Information.

rive TapeAlert 037.
Flag: Drive voltage.
Type: W
Cause: Drive voltage limits exceeded.
Required host message:
The drive detected externally supplied voltages are approaching or outside
the specified voltage limits.  See Error Code 2 in the list of drive error
codes in the 3584 Maintenance Information.

rive TapeAlert 038.
Flag: Predictive failure.
Type: C
Cause: Predictive failure of drive hardware.
Required host message:
A hardware failure of the tape drive is predicted. Call the tape drive
supplier helpline.

rive TapeAlert 039.
Flag: Diagnostics required.
Type: W
Cause: The drive may have had a failure which may be identified by
       stored diagnostic information or by running extended diagnostics
       (eg SCSI Send Diagnostic).
Required host message:
The drive detected a failure that requires diagnostics for isolation.
See Error Code 6 located in the list of drive error codes in the 3584
Maintenance Information.

ibrary TapeAlert 024.
Flag: Library inventory.
Type: C
Cause: Inconsistent media inventory.
Required host message:
Library has detected an inconsistency in its inventory.
1. Run a library inventory to correct the inconsistency.
2. Restart operation.
3. If the problem persists, call your IBM Service Representative.

rive TapeAlert 040.
Flag: Loader hardware A.
Type: C
Cause: Loader mechanism is having trouble communicating with the tape
       drive.
Required host message:
The changer mechanism is having difficulty communicating with the tape
drive:
1. Turn the autoloader off then on.
2. Restart the operation.
3. If problem persists, call the tape drive supplier helpline.

rive TapeAlert 041.
Flag: Loader stray tape.
Type: C
Cause: Stray tape left in loader after previous error recovery.
Required host message:
A tape has been left in the autoloader by a previous hardware fault:
1. Insert an empty magazine to clear the fault.
2. If the fault does not clear, turn the autoloader off then on again.
3. If the problem persists, call the tape drive supplier helpline.

rive TapeAlert 042.
Flag: Loader hardware B.
Type: W
Cause: Loader mechanism has a hardware fault.
Required host message:
There is a problem with the autoloader mechanism.

rive TapeAlert 043.
Flag: Loader door.
Type: C
Cause: Tape changer door open.
Required host message:
The operation failed because the autoloader door is open:
1. Clear any obstructions from the autoloader door.
2. Eject the magazine and then insert it again.
3. If the fault does not clear, turn the autoloader off then on again.
4. If the problem persists, call the tape drive supplier helpline.

rive TapeAlert 044.
Flag: Loader hardware C.
Type: C
Cause: The loader mechanism has a hardware fault that is not
       mechanically related.
Required host message:
The autoloader has a hardware fault:
1. Turn the autoloader off then on again.
2. Restart the operation.
3. If the problem persists, call the tape drive supplier helpline.
Check the autoloader users manual for device specific instructions on
turning the device on and off.

rive TapeAlert 045.
Flag: Loader magazine.
Type: C
Cause: Loader magazine not present.
Required host message:
The autoloader cannot operate without the magazine.
1. Insert the magazine into the autoloader.
2. Restart the operation.

rive TapeAlert 046.
Flag: Loader predictive failure.
Type: W
Cause: Predictive failure of loader mechanism hardware.
Required host message:
A hardware failure of the changer mechanism is predicted. Call the
tape drive supplier helpline.

ibrary TapeAlert 025.
Flag: Library illegal operation.
Type: W
Cause: Illegal operation detected.
Required host message:
The library detected an illegal operation. If the problem persists, call your IBM Service Representative.

rive TapeAlert 050.
Flag: Lost statistics.
Type: W
Cause: Drive or library powered down with tape loaded.
Required host message:
Media statistics have been lost at some time in the past.

rive TapeAlert 051.
Flag: Tape directory invalid at unload.
Type: W
Cause: Error prevented the tape directory being updated on unload.
Required host message:
The tape directory on the tape cartridge that was previously unloaded is corrupted.
The file-search performance is degraded.  Use your backup software to rebuild the
tape directory by reading all the data.

rive TapeAlert 052.
Flag: Tape system area write failure.
Type: C
Cause: Write errors while writing the system log on unload.
Required host message:
The tape cartridge that was previously unloaded could not write it's system area
successfully.  Copy the data to another tape cartridge, then discard the old cartridge.

rive TapeAlert 053.
Flag: Tape system area read failure.
Type: C
Cause: Read errors while reading the system area on load.
Required host message:
The tape system area could not be read successfully at load time. Copy the data to
another tape cartridge, then discard the old cartridge.

TO drive TapeAlert 054.
Flag: No start of data.
Type: C
Cause: Tape damaged, bulk erased, or incorrect format.
Required host message:
The start of data could not be found on the tape:
1. Check you are using the correct format tape.
2. Discard the tape or return the tape to your supplier.

rive TapeAlert 055.
Flag: No start of data.
Type: C
Cause: Loading failure
Required host message:
The operation has failed because the media cannot
be loaded and threaded.
1. Remove the cartridge, inspect it as specified in the
product manual, and retry the operation.
2. If the problem persists, call the tape drive supplier
help line.

rive TapeAlert 056.
Flag: Unrecoverable unload failure.
Type: C
The operation has failed because the medium cannot
be unloaded:
1. Do not attempt to extract the tape cartridge.
2. Call the tape driver supplier help line.

rive TapeAlert 057.
Flag: Automation interface failure.
Type: C
The tape drive has a problem with the automation
interface:
1. Check the power to the automation system.
2. Check the cables and cable connections.
3. Call the supplier help line if problem persists.

rive TapeAlert 058.
Flag: Firmware failure.
Type: W
The tape drive has reset itself due to a detected firmware
fault. If problem persists, call the supplier help
line.

rive TapeAlert 059.
Flag: WORM Medium - Integrity Check Failed
Type: W
The tape drive has detected an inconsistency during
the WORM medium integrity checks. Someone may
have tampered with the cartridge.

ibrary TapeAlert 026.
Flag: Dual-port interface error.
Type: W
Cause: Failure of one interface port in a dual-port configuration, eg
       Fibre channel
Required host message:
A redundant interface port on the library has failed.

rive TapeAlert 060.
Flag: WORM Medium - Overwrite Attempted
Type: W
An attempt had been made to overwrite user data on
a WORM medium:
1. If a WORM medium was used inadvertently, replace
it with a normal data medium.
2. If a WORM medium was used intentionally:
a) check that the software application is compatible
with the WORM medium format you are using.
b) check that the medium is bar-coded correctly for
WORM.

ibrary TapeAlert 027.
Flag: Cooling fan failure.
Type: W
Cause: One or more fans inside the library have failed. Internal flag
       state only cleared when all fans are working again.
Required host message:
A library cooling fan has failed.

ibrary TapeAlert 028.
Flag: Power supply.
Type: W
Cause: Redundant PSU failure inside the library subsystem.
Required host message:
A redundant power supply has failed inside the library. Call your IBM Service Representative.

ibrary TapeAlert 029.
Flag: Power consumption.
Type: W
Cause: Power consumption of one or more devices inside the library is
       outside specified range.
Required host message:
The library power consumption is outside the specified range.

ibrary TapeAlert 003.
Flag: Library hardware C.
Type: C
Cause: The changer mechanism has a hardware fault that requires a reset
       to recover.
Required host message:
The library has a hardware fault:
1. Reset the library.
2. Restart the operation. Check the library users manual for device specific instructions on resetting the device.

ibrary TapeAlert 030.
Flag: Pass-through mechanism failure.
Type: C
Cause: Error occurred in pass-through mechanism during self test or
       while attempting to transfer a cartridge between library modules.
Required host message:
A failure has occurred in the cartridge pass-through mechanism between
two library modules.

ibrary TapeAlert 031.
Flag: Cartridge in pass-through mechanism.
Type: C
Cause: Cartridge left in the pass-through mechanism between two library
       modules.
Required host message:
A cartridge has been left in the library pass-through mechanism from a
previous hardware fault. Check the library users guide for instructions
on clearing this fault.

ibrary TapeAlert 032.
Flag: Unreadable bar code labels.
Type: I
Cause: Unable to read a bar code label on a cartridge during library
       inventory/scan.
Required host message:
During an inventory or scan, the library was unable to read a bar code label on a cartridge.
1. Check for damaged, misaligned, or peeling barcode labels on the cartridge.
2. If no problem is found, call your IBM Service Representative.

ibrary TapeAlert 004.
Flag: Library hardware D.
Type: C
Cause: The changer mechanism has a hardware fault that is not mechanically
       related, or that requires a power cycle to recover.
Required host message:
The library has a hardware fault that is not mechanically related.
1. Restart the operation.
2. If the problem persists, call your IBM Service Representative.

on TapeAlert 001.
Cause: I/O station full.
Required host message:
The Import/Export station is full.

on TapeAlert 002.
Cause: All cartridge slots in the associated logical library are occupied.
Required host message:
The logical library is full.

on TapeAlert 003.
Cause: Library out of LTO cleaning cartridges.
Required host message:
The library is out of LTO cleaning cartridges.

on TapeAlert 004.
Cause: Library out of DLT cleaning cartridges.
Required host message:
The library is out of DLT cleaning cartridges.

on TapeAlert 005.
Cause: I/O station door has been open for five minutes.
Required host message:
The Import/Export station has been open for five minutes.

on TapeAlert 006.
Cause: LTO cleaning cartridge expired.
Required host message:
An LTO cleaning cartridge has expired.

on TapeAlert 007.
Cause: DLT cleaning cartridge expired.
Required host message:
A DLT cleaning cartridge has expired.

on TapeAlert 008.
Cause: Test initiated from operator panel.
Required host message:
This is a test SNMP trap.

on TapeAlert 009.
Cause: Library out of 3592 Enterprise Tape cleaning cartridges.
Required host message:
The library is out of Enterprise Tape cleaning cartridges.

on TapeAlert 010.
Cause: 3593 Enterprise Tape cleaning cartridge expired.
Required host message:
A Enterprise Tape cleaning cartridge has expired.

on TapeAlert 011.
Cause: LTO slots in the library are approaching full capacity.
Required host message:
LTO slots are approaching full capacity.  The library may not be able to import all cartridge in the IO station.

on TapeAlert 012.
Cause: 3592 Enterprise Tape slots in the library are approaching full capacity.
Required host message:
3592 Enterprise Tape slots are approaching full capacity.  The library may not be able to import all cartridge in the IO station.

on TapeAlert 013.
Cause: A host attempted a move to/from a shared drive that was in use by a different host on a different logaical library.
Required host message:
A Host attempted motion to/from a shared drive. The command failed because the shared drive was being used by another logical library.

on TapeAlert 014.
Cause: The library had a problem reading the cartridge with the barcode indicated.  The cartridge label may be scratched or smeared.
Required host message:
The library had a problem reading the barcode of a cartridge.  Please inspect the label for scratches or smears.

on TapeAlert 015.
Cause: The library attempted to call home, but was unsuccessful.
Required host message:
The library attempted to call home, but was unsuccessful.

on TapeAlert 016.
Cause: The associated logical library is nearing full capacity.
Required host message:
The logical library is almost full.

on TapeAlert 017.
Cause: All 3592 Enterprise Tape slots in the library are allocated to a cartridge.
Required host message:
All physical 3592 Enterprise Tape slots are allocated.  No more 3592 Enterprise Tape cartridges may be added at this time.

on TapeAlert 018.
Cause: All LTO Tape slots in the library are allocated to a cartridge.
Required host message:
All physical LTO Tape slots are allocated.  No more LTO Tape cartridges may be added at this time.

on TapeAlert 019.
Cause: Unable to reach associated EKM.
Required host message:
Library is unable to communicate with the associated EKM address.

on TapeAlert 020.
Cause: A cartridge that can not be encrypted has is loaded in a drives that is used to encrypt all cartridges.
Required host message:
A cartridge that can not be encrypted has been loaded into a drive that is setup for encryption.

on TapeAlert 021.
Cause: A new unassigned cartridge is in the library.
Required host message:
A new cartridge is in the library and is currently unassigned.

on TapeAlert 022.
Cause: All library doors are closed.  The library will inventory and resume operations.
Required host message:
All library doors have been closed.  The library will now inventory and resume operations.

on TapeAlert 040.
Cause: A user has successfully logged in to the web or operator panel.
Required host message:
A user has successfully logged into the Web Specialist or Operator Panel.

on TapeAlert 041.
Cause: A user has attempted to log in to the web or operator panel and was unsuccessful.
Required host message:
A user has attempted to log in to the Web Specialist or Operator Panel and was unsuccessful after 3 attempts.

on TapeAlert 042.
Cause: A user has logged out of the web or operator panel.
Required host message:
A user has logged out of the Web Specialist or Operator Panel.

on TapeAlert 043.
Cause: A library configuration setting has been changed.
Required host message:
A library configuration setting has been changed via the Op Panel or Web Specialist.

on TapeAlert 044.
Cause: A logical library configuration setting has been changed.
Required host message:
A logical library configuration setting has been changed.

on TapeAlert 045.
Cause: A tape drive configuration setting has been changed.
Required host message:
A tape drive configuration setting has been changed.

on TapeAlert 046.
Cause: A cartridge has been modified from an external UI.
Required host message:
A cartridge has been modified from the Web Specialist or Op Panel.

on TapeAlert 047.
Cause: A library or drive code load has been initiated from an external UI.
Required host message:
A library or drive code load has been initiated from the Web Specialist, Op Panel, or CE Tool.

on TapeAlert 048.
Cause: An Accessor FRU been prepared/finished.
Required host message:
An Accessor has been placed in the prepared or finished Accessor service state.

on TapeAlert 049.
Cause: A drive FRU been prepared/finished.
Required host message:
A drive has been placed in the prepared or finished Accessor service state.

on TapeAlert 050.
Cause: A drive Serial number has changed.
Required host message:
A drive Serial number has changed.

on TapeAlert 051.
Cause: A drive has been power cycled from the web UI.
Required host message:
A drive has been power cycled via the Web Specialist.

on TapeAlert 052.
Cause: A node card has been reset from the web UI.
Required host message:
A node card has been reset via the Web Specialist.

ibrary TapeAlert 005.
Flag: Library diagnostics required.
Type: W
Cause: The changer mechanism has a hardware fault which would be
       identified by extended diagnostics (eg SCSI Send Diagnostic).
Required host message:
The library mechanism may have a hardware fault.
Run extended diagnostics to verify and diagnose the problem.
Check the library users manual for device specific instructions
on running extended diagnostic tests.

ibrary TapeAlert 006.
Flag: Library interface.
Type: C
Cause: The library has identified an interfacing fault.
Required host message:
The library has a problem with the host interface:
1. Check the cables and cable connections.
2. Restart the operation.

ibrary TapeAlert 007.
Flag: Predictive failure.
Type: W
Cause: Predictive failure of library hardware.
Required host message:
A hardware failure of the library is predicted. Call the library supplier
helpline.

ibrary TapeAlert 008.
Flag: Library maintenance.
Type: W
Cause: Library preventive maintenance required.
Required host message:
Preventative maintenance of the library is required. Check the library
users manual for device specific preventative maintenance tasks, or call
your library supplier helpline.

ibrary TapeAlert 009.
Flag: Library humidity limits.
Type: C
Cause: Library humidity limits exceeded.
Required host message:
General environmental conditions inside the library are outside the
specified humidity range.