HUAWEI-VDSL2-LINE-MIB Table View

The table vdsl2LineTable contains configuration,
command and status parameters of the VDSL2 line.
The index of this table is ifIndex.

vdsl2LineEntry row .1.3.6.1.4.1.2011.6.115.1.1.1.1

The table vdsl2LineTable contains configuration,
command and status parameters of the VDSL2 line.
The index of this entry is ifIndex.

Indexes

IF-MIBifIndex

Column	Syntax	OID
vdsl2LineCnfgTemplate The value of this object identifies the row in the VDSL2 Line Configuration Templates Table, (Vdsl2ConfTemplatesTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.1
vdsl2LineAlarmCnfgTemplate The value of this object identifies the row in the VDSL2 Line Alarm Configuration Template Table, (vdsl2LineAlarmConfTemplateTable), which applies to this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.2
vdsl2LineCmndConfPmsf Power management state forced. Defines the line states to be forced by the near-end xTU on this line. Options: 1. l3toL0(0) - Force the line to transition from the L3 idle state to the L0 full-…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2ConfPmsForcer/w Type Values: -1 invalidValue 0 l3toL0 2 l0toL2 3 l0orL2toL3	.1.3.6.1.4.1.2011.6.115.1.1.1.1.3
vdsl2LineCmndConfLdsf Loop diagnostics mode forced (LDSF). Defines whether the line should be forced into the loop diagnostics mode by the near-end xTU on this line or only be responsive to loop diagnostics initiated by the far-end xTU.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LineLdsfr/w Type Values: -1 invalidValue 0 inhibit 1 force	.1.3.6.1.4.1.2011.6.115.1.1.1.1.4
vdsl2LineCmndConfLdsfFailReason The status of the recent occasion the Loop diagnostics mode forced (LDSF) was issued for the associated line. Options: 1. none(1) - The default value in case LDSF was never requested for t…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LdsfResult Type Values: 1 none 2 success 3 inProgress 4 unsupported 5 cannotRun 6 aborted 7 failed 8 illegalMode 9 adminUp 10 tableFull 11 noResources	.1.3.6.1.4.1.2011.6.115.1.1.1.1.5
vdsl2LineCmndAutomodeColdStart Automode cold start forced. This parameter is defined in order to improve testing of the performance of ATUs supporting automode when it is enabled in the MIB. Change the value of this parameter to 'true' indicates a ch…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.6.115.1.1.1.1.6
vdsl2LineStatusXtuTransSys The xTU Transmission System (XTS) in use. This parameter may be derived from the handshaking procedures defined in Recommendation G.994.1. The invalid value is 4294967295. If data on the port is invalid or no data is g…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.7
vdsl2LineStatusPwrMngState The current power management state. Options: 1. L0 - Synchronized and full transmission 2. L1 - Low Power with reduced net data rate 3. L2 - Low Power with reduced net data rate 4. L3 - No power The various possibl…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2PowerMngState Type Values: -1 invalidValue 0 l0 1 l1 2 l2 3 l3	.1.3.6.1.4.1.2011.6.115.1.1.1.1.8
vdsl2LineStatusInitResult Indicates the result of the last full initialization performed on the line. Options: 1. noFail (0) - Successful initialization 2. configError (1) - Configuration failure 3. configNotF…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2InitResult Type Values: -1 invalidValue 0 noFail 1 configError 2 configNotFeasible 3 commFail 4 noPeerXtu 5 otherCause 6 ginpNotSelected	.1.3.6.1.4.1.2011.6.115.1.1.1.1.9
vdsl2LineStatusLastStateDs The last successful transmitted initialization state in the downstream direction in the last full initialization performed on the line. States are per the specific VDSL type and are counted from 0 (if G.994.1 is used) o…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LastTransmittedState Type Values: -1 invalidValue 0 xtucG9941 1 xtucQuiet1 2 xtucComb1 3 xtucQuiet2 4 xtucComb2 5 xtucIcomb1 6 xtucLineprob 7 xtucQuiet3 8 xtucComb3 9 xtucIComb2 10 xtucMsgfmt 11 xtucMsgpcb 12 xtucQuiet4 13 xtucReverb1 14 xtucTref1 15 xtucReverb2 16 xtucEct 17 xtucReverb3 18 xtucTref2 19 xtucReverb4 20 xtucSegue1 21 xtucMsg1 22 xtucReverb5 23 xtucSegue2 24 xtucMedley 25 xtucExchmarker 26 xtucMsg2 27 xtucReverb6 28 xtucSegue3 29 xtucParams 30 xtucReverb7 31 xtucSegue4 32 xtucShowtime 100 xturG9941 101 xturQuiet1 102 xturComb1 103 xturQuiet2 104 xturComb2 105 xturIcomb1 106 xturLineprob 107 xturQuiet3 108 xturComb3 109 xturIcomb2 110 xturMsgfmt 111 xturMsgpcb 112 xturReverb1 113 xturQuiet4 114 xturReverb2 115 xturQuiet5 116 xturReverb3 117 xturEct 118 xturReverb4 119 xturSegue1 120 xturReverb5 121 xturSegue2 122 xturMsg1 123 xturMedley 124 xturExchmarker 125 xturMsg2 126 xturReverb6 127 xturSegue3 128 xturParams 129 xturReverb7 130 xturSegue4 131 xturShowtime	.1.3.6.1.4.1.2011.6.115.1.1.1.1.10
vdsl2LineStatusLastStateUs The last successful transmitted initialization state in the upstream direction in the last full initialization performed on the line. States are per the specific VDSL type and are counted from 0 (if G.994.1 is used) or…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LastTransmittedState Type Values: -1 invalidValue 0 xtucG9941 1 xtucQuiet1 2 xtucComb1 3 xtucQuiet2 4 xtucComb2 5 xtucIcomb1 6 xtucLineprob 7 xtucQuiet3 8 xtucComb3 9 xtucIComb2 10 xtucMsgfmt 11 xtucMsgpcb 12 xtucQuiet4 13 xtucReverb1 14 xtucTref1 15 xtucReverb2 16 xtucEct 17 xtucReverb3 18 xtucTref2 19 xtucReverb4 20 xtucSegue1 21 xtucMsg1 22 xtucReverb5 23 xtucSegue2 24 xtucMedley 25 xtucExchmarker 26 xtucMsg2 27 xtucReverb6 28 xtucSegue3 29 xtucParams 30 xtucReverb7 31 xtucSegue4 32 xtucShowtime 100 xturG9941 101 xturQuiet1 102 xturComb1 103 xturQuiet2 104 xturComb2 105 xturIcomb1 106 xturLineprob 107 xturQuiet3 108 xturComb3 109 xturIcomb2 110 xturMsgfmt 111 xturMsgpcb 112 xturReverb1 113 xturQuiet4 114 xturReverb2 115 xturQuiet5 116 xturReverb3 117 xturEct 118 xturReverb4 119 xturSegue1 120 xturReverb5 121 xturSegue2 122 xturMsg1 123 xturMedley 124 xturExchmarker 125 xturMsg2 126 xturReverb6 127 xturSegue3 128 xturParams 129 xturReverb7 130 xturSegue4 131 xturShowtime	.1.3.6.1.4.1.2011.6.115.1.1.1.1.11
vdsl2LineStatusXtur Indicates current state (existing failures) of the xTU-R. This is a bit-map of possible conditions. The various bit positions are: noFailure(0), lossOfFraming(1), lossOfSignal(2), lossOfPower(3), initFailure(4) - never…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LineStatus Type Values: 0 noDefect 1 lossOfFraming 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.4.1.2011.6.115.1.1.1.1.12
vdsl2LineStatusXtuc Indicates current state (existing failures) of the xTU-C. This is a bit-map of possible conditions. This BITS structure can report the following failures: 1. noDefect (0) - This bit position positively reports …	HUAWEI-VDSL2-LINE-TC-MIBVdsl2LineStatus Type Values: 0 noDefect 1 lossOfFraming 2 lossOfSignal 3 lossOfPower 4 initFailure	.1.3.6.1.4.1.2011.6.115.1.1.1.1.13
vdsl2LineStatusLnAttenDs The measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub-carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (…	0.1 dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.14
vdsl2LineStatusLnAttenUs The measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub- carriers during diagnostics mode and initialization. It ranges from 0 to 1270 units of 0.1 dB (…	0.1 dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.15
vdsl2LineStatusSigAttenDs The measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 1…	0.1 dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.16
vdsl2LineStatusSigAttenUs The measured difference in the total power transmitted by the xTU-R and the total power received by the xTU-C over all sub- carriers during Showtime. It ranges from 0 to 1270 units of 0.1 dB (Physical values are 0 to 1…	0.1 dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.17
vdsl2LineStatusSnrMarginDs Downstream SNR Margin is the maximum increase in dB of the noise power received at the xTU-R, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physi…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.18
vdsl2LineStatusSnrMarginUs Upstream SNR Margin is the maximum increase in dB of the noise power received at the xTU-C, such that the BER requirements are met for all downstream bearer channels. It ranges from -640 to 630 units of 0.1 dB (Physica…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.19
vdsl2LineStatusAttainableRateDs Maximum Attainable Data Rate Downstream. The maximum downstream net data rate currently attainable by the xTU-C transmitter and the xTU-R receiver, coded in bit/s. The invalid value is 4294967295. If data on the port is…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.20
vdsl2LineStatusAttainableRateUs Maximum Attainable Data Rate Upstream. The maximum upstream net data rate currently attainable by the xTU-R transmitter and the xTU-C receiver, coded in bit/s. The invalid value is 4294967295. If data on the port is inv…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.21
vdsl2LineStatusActPsdDs Actual Power Spectrum Density (PSD) Downstream. The average downstream transmit PSD over the sub-carriers used for downstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value o…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.22
vdsl2LineStatusActPsdUs Actual Power Spectrum Density (PSD) Upstream. The average upstream transmit PSD over the sub-carriers used for upstream. It ranges from -900 to 0 units of 0.1 dB (Physical values are -90 to 0 dBm/Hz). A value of 0x7FF…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.23
vdsl2LineStatusActAtpDs Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical val…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.24
vdsl2LineStatusActAtpUs Actual Aggregate Transmit Power Upstream. The total amount of transmit power delivered by the xTU-R at the U-R reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical value…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.25
vdsl2LineBandPlan Band contains a series of subcarriers. The first octet is the number of bands. Other octets describe the info of each band. Each band info is a pair of values occupying 4 octets with the following structure: Fir…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2BandPlan Type Constraints: range: 0..96	.1.3.6.1.4.1.2011.6.115.1.1.1.1.26
vdsl2LinePsdMaskClassSelection The sub class of VDSL2 PSD Mask.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2TIPsdClassMask Type Values: -1 invalidValue 1 none 2 a998B997M1cC998 3 b997M1x 4 b997M2x 5 b998M1x 6 b998M2x	.1.3.6.1.4.1.2011.6.115.1.1.1.1.27
vdsl2LineCurrentVdsl2Profile This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2SubProfiles Type Values: -1 invalidValue 1 profile8a 2 profile8b 3 profile8c 4 profile8d 5 profile12a 6 profile12b 7 profile17a 8 profile30a	.1.3.6.1.4.1.2011.6.115.1.1.1.1.28
vdsl2LineCnfgServiceProf The value of this object identifies the row in the VDSL2 Line Configuration Service Profile Table, (vdsl2ServProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.29
vdsl2LineCnfgSpectrumProf The value of this object identifies the row in the VDSL2 Line Configuration Spectrum Profile Table, (vdsl2SpectrumProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.30
vdsl2LineCnfgDpboProf The value of this object identifies the row in the VDSL2 Line Configuration Dpbo Profile Table, (vdsl2DpboProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.31
vdsl2LineCnfgUpboProf The value of this object identifies the row in the VDSL2 Line Configuration Upbo Profile Table, (vdsl2UpboProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.32
vdsl2LineCnfgNoiseMarginProf The value of this object identifies the row in the VDSL2 Line Configuration Noise Margin Profile Table, (vdsl2NoiseMarginProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.33
vdsl2LineCnfgDelayINPProf The value of this object identifies the row in the VDSL2 Line Configuration Delay-INP Profile Table, (vdsl2DelayInpProfTable), which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.34
vdsl2UpboProfKl0CpeVal The actual value of KL0_CPE parameter,it ranges from 0 to 1280 units of 0.1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port …	0.1dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.35
vdsl2LineStatusCodingGainDs The actual value of Coding gain downstream parameter,it ranges from 0 to 16 units of 0.5 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated…	0.5dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.36
vdsl2LineStatusCodingGainUs The actual value of Coding gain upstream parameter,it ranges from 0 to 16 units of 0.5 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated o…	0.5dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.37
vdsl2LineStatusPcbDs The actual value of power cut back downstream parameter, it ranges from 0 to 40 units of 1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generat…	1dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.38
hwvdslDlmDsmprofile The value of this object identifies the row in the DLM/DSM Profile Table, which applies for this VDSL2 line.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.1.1.1.39
hwvdsl2LineActmode Actived mode after training between co and cpe. Options: 1. ADSL(1) - ETSI,T1.413 G992.1,G992.2 2. ADSL2(2) - G992.3,G992.4 3. ADSL2PLUS(3) - G992.5 4. VDSL(4) - G993.1 5. VDSL2(5) …	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Actmode Type Values: -1 invalidValue 1 adsl 2 adsl2 3 adsl2plus 4 vdsl 5 vdsl2	.1.3.6.1.4.1.2011.6.115.1.1.1.1.40
vdsl2UpboProfKl0CoVal The actual value of KL0_CO parameter, it ranges from 0 to 1280 units of 0.1 dB. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port…	0.1dBSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.41
vdsl2LineStatusRtxUsedDs This parameter specifies whether G.998.4 retransmission is used in downstream. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MO…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2StatusRtxUsed Type Values: -1 invalidValue 1 rtxInuse 2 rtxUnusedModeForbidden 3 rtxUnusedNotSupportedXtuc 4 rtxUnusedNotSupportedXtur 5 rtxUnusedNotSupportedXtucAndXtur	.1.3.6.1.4.1.2011.6.115.1.1.1.1.42
vdsl2LineStatusRtxUsedUs This parameter specifies whether G.998.4 retransmission is used in upstream. Options: 1. rtxInuse(1) - RTX in use 2. rtxUnusedModeForbidden(2) - RTX not in use, due to RTX_MOD…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2StatusRtxUsed Type Values: -1 invalidValue 1 rtxInuse 2 rtxUnusedModeForbidden 3 rtxUnusedNotSupportedXtuc 4 rtxUnusedNotSupportedXtur 5 rtxUnusedNotSupportedXtucAndXtur	.1.3.6.1.4.1.2011.6.115.1.1.1.1.43
vdsl2LineStatusLastRetrainInfo Indicates the last retrained information performed on the line. Options: 1. none(1) - No record is available …	Enumeration Enumerated Values: 1 none 2 cpe-l3-trigger 3 lom-us-trigger-dra 4 lom-ds-trigger-dra 5 cpe-never-answer-oam 6 cpe-no-more-answer-oam 7 persistent-ncd-us 8 persistent-ncd-ds 9 persistent-lcd-us 10 persistent-lcd-ds 11 l2-problem-co-drop 12 l2-problem-cpe-drop 13 bitswap-refused-us-co-drop 14 bitswap-refused-us-cpe-drop 15 channel-change-us-co-drop 16 channel-change-us-cpe-drop 17 noise-increase-us-co-drop 18 noise-increase-us-cpe-drop 19 bitswap-refused-ds-co-drop 20 bitswap-refused-ds-cpe-drop 21 channel-change-ds-co-drop 22 channel-change-ds-cpe-drop 23 noise-increase-ds-co-drop 24 noise-increase-ds-cpe-drop 25 lom-us-co-drop 26 lom-us-cpe-drop 27 lom-ds-co-drop 28 lom-ds-cpe-drop 29 sra-problem-us-co-drop 30 sra-problem-us-cpe-drop 31 sra-failed-us-co-drop 32 sra-failed-us-cpe-drop 33 sra-problem-ds-co-drop 34 sra-problem-ds-cpe-drop 35 sra-rejected-ds-co-drop 36 sra-rejected-ds-cpe-drop 37 bitswap-problem-us-co-drop 38 bitswap-problem-us-cpe-drop 39 bitswap-failed-us-co-drop 40 bitswap-failed-us-cpe-drop 41 bitswap-problem-ds-co-drop 42 bitswap-problem-ds-cpe-drop 43 bitswap-rejected-ds-co-drop 44 bitswap-rejected-ds-cpe-drop 45 cpe-switched-off 46 cpe-lost 47 co-reset 48 co-stop 49 unknown	.1.3.6.1.4.1.2011.6.115.1.1.1.1.44
vdsl2UpboRxThreshDs This parameter reports the downstream received signal level threshold value used in the Alternative Electrical Length Estimation method (ELE-M1). This parameter represents an offset from -100 dB, and ranges from -64 …	dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.45
vdsl2UpboRxThreshUs This parameter reports the upstream received signal level threshold value used in the Alternative Electrical Length Estimation method (ELE-M1). This parameter represents an offset from -100 dB, and ranges from -64 dB…	dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.1.1.1.46
hwvdsl2LineStatusLineRateDs The actual line rate downstream. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the i…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.47
hwvdsl2LineStatusLineRateUs The actual line rate upstream. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been activated, the inv…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.48
hwvdsl2LineSplitterMode This parameter indicates which mode will be applied to the port splitter .The valid values for the splitter mode are 1 and 2. Options: 1. connect (1) - Splitter mode is connect 2. bypass (2) - Split…	Enumerationr/w Enumerated Values: 1 connect 2 bypass	.1.3.6.1.4.1.2011.6.115.1.1.1.1.49
hwvdsl2LineBackup This parameter indicates whether the port backup is enabled. Options: 1. enable(1) - Enable the port backup. 2. disable(2) - Disable the port backup.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2011.6.115.1.1.1.1.50
hwvdsl2LineBackupPort This parameter indicates the backup port ifindex. If data on the port is invalid or no data is generated on the port, the port is not backed up. The invalid value is 4294967295.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.1.1.1.51
hwvdsl2LinePhyRcontrol This parameter indicates whether the PHY-R retransmission is enabling. In TR165 mode, the H80BVDPM board should be enabled when it works as ADSL mode. Options: 1. enable(1) - Enable the PHY-R retransmission of…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2011.6.115.1.1.1.1.52
hwvdsl2LineStatusActPsdLimitMask (LIMITMASK). This parameter contains the actual G.993.2 limit PSD masks selected during showtime. Options: 1. annexA998-D-32(1) - D-32 2. annexA998-D-64(2) - D-64 3. annexB997-M1c-A-7(…	Enumeration Enumerated Values: -1 invalidValue 1 annexA998-D-32 2 annexA998-D-64 3 annexB997-M1c-A-7 4 annexB997-M1x-M-8 5 annexB997-M1x-M 6 annexB997-M2x-M-8 7 annexB997-M2x-A 8 annexB997-M2x-M 9 annexB998-M1x-A 10 annexB998-M1x-B 11 annexB998-M1x-NUS0 12 annexB998-M2x-A 13 annexB998-M2x-M 14 annexB998-M2x-B 15 annexB998-M2x-NUS0 16 annexBHPE17-M1-NUS0 17 annexBHPE30-M1-NUS0 18 annexB997E17-M2x-A 19 annexB997E30-M2x-NUS0 20 annexB998E17-M2x-NUS0 21 annexB998E17-M2x-NUS0-M 22 annexB998ADE17-M2x-NUS0-M 23 annexB998ADE17-M2x-B 24 annexB998E30-M2x-NUS0 25 annexB998E30-M2x-NUS0-M 26 annexB998ADE30-M2x-NUS0-M 27 annexB998ADE17-M2x-A 28 annexB998ADE30-M2x-NUS0-A 29 annexA998-D-48 30 annexA998-D-128 31 annexB998ADE17-M2x-M 32 annexB998E17-M2x-A	.1.3.6.1.4.1.2011.6.115.1.1.1.1.53

The table vdsl2ChannelStatusTable contains status
parameters of VDSL2 channel. 
The indexes of this table are ifIndex and vdsl2ChStatusUnit.

vdsl2ChannelStatusEntry row .1.3.6.1.4.1.2011.6.115.1.2.1.1

The table vdsl2ChannelStatusTable contains status
parameters of VDSL2 channel.
The indexes of this entry are ifIndex and vdsl2ChStatusUnit.

Indexes

IF-MIBifIndex vdsl2ChStatusUnit

Column	Syntax	OID
vdsl2ChStatusUnit The termination unit xTU-C(1) or xTU-R(2).	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.4.1.2011.6.115.1.2.1.1.1
vdsl2ChStatusChannelNum Provides the bearer channel number associated with this row (i.e., the channel ifIndex). This enables determining the channel configuration profile and the channel thresholds profile applicable for this bearer channel.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.2
vdsl2ChStatusActDataRate If retransmission is not used in a given transmit direction, this parameter reports the actual net data rate at which the bearer channel is operating in L0 power management state, and in L1 or L2 states, the paramete…	bits/secondUnsigned32 Constraints: range: 0-200000000	.1.3.6.1.4.1.2011.6.115.1.2.1.1.3
vdsl2ChStatusPrevDataRate If retransmission is not used in a given transmit direction, this parameter reports the previous net data rate the bearer channel was operating at just before the latest net data rate change event occurred, excluding…	bits/secondUnsigned32 Constraints: range: 0-200000000	.1.3.6.1.4.1.2011.6.115.1.2.1.1.4
vdsl2ChStatusActDelay If retransmission is not used in a given transmit direction, this parameter is the actual one-way interleaving delay introduced by the PMS-TC excluding delay in L1 and L2 state. In L1 and L2 state, the parameter cont…	millisecondsUnsigned32 Constraints: range: 0-8176	.1.3.6.1.4.1.2011.6.115.1.2.1.1.5
vdsl2ChStatusAtmStatus Indicates current state (existing failures) of the VDSL channel in case its Data Path is ATM. This is a bit-map of possible conditions. Options: 1. noDefect(0) - This bit position positively …	HUAWEI-VDSL2-LINE-TC-MIBVdsl2ChAtmStatus Type Values: 0 noDefect 1 noCellDelineation 2 lossOfCellDelineation	.1.3.6.1.4.1.2011.6.115.1.2.1.1.6
vdsl2ChStatusPtmStatus Indicates current state (existing failures) of the VDSL channel in case its Data Path is PTM. This is a bit-map of possible conditions. Options: 1. noFailure(0) - No failure 2. outOfSync (1) - Out of synchronizati…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2ChPtmStatus Type Values: 0 noDefect 1 outOfSync	.1.3.6.1.4.1.2011.6.115.1.2.1.1.7
vdsl2ChStatusINP If retransmission is not used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) on the bearer channel in the L0 state. In the L1 or L2 state, the parameter contains the I…	0.1 DMT symbolUnsigned32 Constraints: range: 0-254	.1.3.6.1.4.1.2011.6.115.1.2.1.1.8
vdsl2ChStatusRSRedundancy The actual number of Reed-Solomon redundancy bytes per codeword used in the latency path in which the bearer channel is transported. The value is coded in bytes. The value 0 indicates no Reed-Solomon coding. The inva…	byteUnsigned32 Constraints: range: 0-16	.1.3.6.1.4.1.2011.6.115.1.2.1.1.9
vdsl2ChStatusRSSymbols The DMT Symbol number per codeword used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the …	0.01 DMT symbolSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.10
vdsl2ChStatusInterDepth The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The value ranges from 1 to 4096 by step of 1. The value 1 indicates no interleaving. The invalid value is 42…	Unsigned32 Constraints: range: 1-4096	.1.3.6.1.4.1.2011.6.115.1.2.1.1.11
vdsl2ChStatusSymbolLength The actual number of bits per symbol assigned to the latency path in which the bearer channel is transported. This value does not include trellis overhead. The invalid value is 4294967295. If data on the port is inva…	bitUnsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.2011.6.115.1.2.1.1.12
vdsl2ChStatusRSSize The actual Reed-Solomon codeword size used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because …	byteUnsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.2011.6.115.1.2.1.1.13
vdsl2ChStatusInterBlockLength The actual block length of the interleaver used in the latency path in which the bearer channel is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port bec…	byteUnsigned32 Constraints: range: 4-255	.1.3.6.1.4.1.2011.6.115.1.2.1.1.14
vdsl2ChStatusLPATH The index of the actual latency path in which the bearer is transported. The invalid value is 4294967295. If data on the port is invalid or no data is generated on the port because the port has not been activated, th…	Unsigned32 Constraints: range: 0-3	.1.3.6.1.4.1.2011.6.115.1.2.1.1.15
vdsl2ChStatusPhyRrrcBits The bits in the channel that used to retransmission. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not be…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.16
vdsl2ChStatusPhyRtxQueue Queues in send buffer used for retransmission. The invalid value is 4294967295. If data on the port cannot be queried, data on the port is invalid, or no data is generated on the port because the port has not been ac…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.17
vdsl2ChStatusActNetDataRate In L0 state, this parameter reports the Net Data Rate at which the bearer channel is operating. In L2 state, this parameter contains the Net Data Rate in the previous L0 state. This parameter is optional if G.998.4 re…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.18
vdsl2ChStatusActINPAgainstREIN If retransmission is used in a given transmit direction, this parameter reports the actual impulse noise protection (INP) against REIN (under specific conditions detailed in G.998.4) on the bearer channel in the L0 s…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.19
hwvdsl2ChStatusUnlimitedVersionEtru The unlimited version of expected throughput in kbit/s:(1 - RTxOH) * NDR. This value is specified in G.998.4 (G.INP).	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.1.1.20

The table vdsl2PrivSCStatusTable contains status parameters
of VDSL2 sub-carriers. 
The indexes of this table are ifIndex and vdsl2PrivSCStatusDirection.

vdsl2PrivSCStatusEntry row .1.3.6.1.4.1.2011.6.115.1.2.2.1

The table vdsl2PrivSCStatusTable contains status parameters
of VDSL2 sub-carriers.
The indexes of this entry are ifIndex and vdsl2PrivSCStatusDirection.

Indexes

IF-MIBifIndex vdsl2PrivSCStatusDirection

Column	Syntax	OID
vdsl2PrivSCStatusDirection The direction of the sub-carrier either upstream or downstream.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Direction Type Values: 1 upstream 2 downstream	.1.3.6.1.4.1.2011.6.115.1.2.2.1.1
vdsl2PrivSCStatusMtime SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 …	symbolsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.2.1.2
vdsl2PrivSCStatusSnr The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 4096 bytes, designed for supporting up to 4096 sub-carriers. The number …	OctetString Constraints: range: 0-4096	.1.3.6.1.4.1.2011.6.115.1.2.2.1.3
vdsl2PrivSCStatusBitsAlloc The bits allocation per sub-carrier. An array of 2048 bytes, designed for supporting up to 4096 sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depen…	bitsOctetString Constraints: range: 0-2048	.1.3.6.1.4.1.2011.6.115.1.2.2.1.4
vdsl2PrivSCStatusGainAlloc The gain allocation per sub-carrier. An array of 8192 bytes, designed for supporting up to 4096 sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depend…	OctetString Constraints: range: 0-8192	.1.3.6.1.4.1.2011.6.115.1.2.2.1.5

The table vdsl2SCStatusTable contains
sub-carrier status parameters for VDSL2/ADSL/ADSL2
and ADSL2+ that DO NOT refer to specific sub-carriers.
In addition, the table contains parameters
that provide information about the size of parameters
in vdsl2SCStatusSegmentTable.  This table contains live data
from equipment. The indexes of this table are ifIndex and 
vdsl2SCStatusDirection.

vdsl2SCStatusEntry row .1.3.6.1.4.1.2011.6.115.1.2.3.1

The table vdsl2SCStatusTable contains
sub-carrier status parameters for VDSL2/ADSL/ADSL2
and ADSL2+ that DO NOT refer to specific sub-carriers.
In addition, the table contains parameters
that provide information about t…

Indexes

IF-MIBifIndex vdsl2SCStatusDirection

Column	Syntax	OID
vdsl2SCStatusDirection The direction of the sub-carrier either upstream or downstream	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Direction Type Values: 1 upstream 2 downstream	.1.3.6.1.4.1.2011.6.115.1.2.3.1.1
vdsl2SCStatusLinScale The scale factor to be applied to the H(f) linear representation values for the respective transmission direction. This parameter is only available after a loop diagnostic procedure.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.3.1.2
vdsl2SCStatusLinScGroupSize Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.3.1.3
vdsl2SCStatusLogMt The number of symbols used to measure the H(f) logarithmic measurement values for the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.3.1.4
vdsl2SCStatusLogScGroupSize Number of sub-carriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.3.1.5
vdsl2SCStatusQlnMt The number of symbols used to measure the Quiet Line Noise values on the respective transmission direction. This parameter should correspond to the value specified in the recommendation (e.g., the number of symbols in…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.3.1.6
vdsl2SCStatusQlnScGroupSize Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is e…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.3.1.7
vdsl2SCStatusMtime SNR Measurement Time. The number of symbols used to measure the SNR values on the respective transmission direction. It should correspond to the value specified in the recommendation (e.g., the number of symbols in 1 …	symbolsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.3.1.8
vdsl2SCStatusSnrScGroupSize Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the si…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.3.1.9
vdsl2SCStatusAttainableRate Maximum Attainable Data Rate. The maximum net data rate currently attainable by the XTU-C transmitter and XTU-R receiver (when referring to downstream direction) or by the XTU-R transmitter and XTU-C receiver (when ref…	bits/secondSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.3.1.10
vdsl2SCStatusActAtp Actual Aggregate Transmit Power from the XTU (XTU-R on downstream direction and XTU-C on upstream direction), at the instant of measurement. It ranges from -310 to 310 units of 0.1 dB (Physical values are -31 to 31 dBm…	0.1 dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.2.3.1.11
vdsl2SCStatusRowStatus Row Status. The SNMP agent should create rows in this table and in the vdsl2SCStatusTable for storing the results of a DELT performed on the associated line, if such rows do not already exist. The SNMP agent may have l…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.6.115.1.2.3.1.12
vdsl2SCStatusProfile This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Profiles Type Values: -1 invalidValue 1 profile8a 2 profile8b 3 profile8c 4 profile8d 5 profile12a 6 profile12b 7 profile17a 8 profile30a	.1.3.6.1.4.1.2011.6.115.1.2.3.1.13
vdsl2SCStatusClassmask In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: - Class 998 Annex A: D-32, D-64. - Class 997-M1c Annex B: 997-M1c-A-7. - Class 997-M1x…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2PSDClassMask Type Values: -1 invalidValue 1 annexA998-D-32 2 annexA998-D-64 3 annexB997-M1c-A-7 4 annexB997-M1x-M-8 5 annexB997-M1x-M 6 annexB997-M2x-M-8 7 annexB997-M2x-A 8 annexB997-M2x-M 9 annexB998-M1x-A 10 annexB998-M1x-B 11 annexB998-M1x-NUS0 12 annexB998-M2x-A 13 annexB998-M2x-M 14 annexB998-M2x-B 15 annexB998-M2x-NUS0 16 annexBHPE17-M1-NUS0 17 annexBHPE30-M1-NUS0 18 annexB997E17-M2x-A 19 annexB997E30-M2x-NUS0 20 annexB998E17-M2x-NUS0 21 annexB998E17-M2x-NUS0-M 22 annexB998ADE17-M2x-NUS0-M 23 annexB998ADE17-M2x-B 24 annexB998E30-M2x-NUS0 25 annexB998E30-M2x-NUS0-M 26 annexB998ADE30-M2x-NUS0-M 27 annexB998ADE17-M2x-A 28 annexB998ADE30-M2x-NUS0-A 29 annexA998-D-48 30 annexA998-D-128 31 annexB998ADE17-M2x-M 32 annexB998E17-M2x-A	.1.3.6.1.4.1.2011.6.115.1.2.3.1.14

The table vdsl2SCStatusBandTable contains
sub-carrier status parameters for VDSL2/ADSL/ADSL2
and ADSL2+ that are grouped per-band.
For ADSL/ADSL2/ADSL2+, there is a single
upstream band and a single downstream band.
For VDSL2, there are several downstream bands and
several upstream bands. 
The indexes of this table are ifIndex and vdsl2SCStatusBand.

vdsl2SCStatusBandEntry row .1.3.6.1.4.1.2011.6.115.1.2.4.1

The table vdsl2SCStatusBandTable contains
sub-carrier status parameters for VDSL2/ADSL/ADSL2
and ADSL2+ that are grouped per-band.
For ADSL/ADSL2/ADSL2+, there is a single
upstream band and a single downstream band.
For…

Indexes

IF-MIBifIndex vdsl2SCStatusBand

Column	Syntax	OID
vdsl2SCStatusBand The transmission band. Identifies a band in a VDSL2/ADSL/ADSL2/ADSL2+ link. For a band in the upstream direction, transmission is from the remote end (xTU-R) towards the central office end (xTU-C). A band in the upstr…	HUAWEI-VDSL2-LINE-TC-MIBXdsl2Band Type Values: 1 upstream 2 downstream 3 us0 4 ds1 5 us1 6 ds2 7 us2 8 ds3 9 us3 10 ds4 11 us4	.1.3.6.1.4.1.2011.6.115.1.2.4.1.1
vdsl2SCStatusBandLnAtten When referring to a band in the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub-carriers during diagnostics mode. …	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.4.1.2011.6.115.1.2.4.1.2
vdsl2SCStatusBandSigAtten When referring to a band the downstream direction, it is the measured difference in the total power transmitted by the xTU-C and the total power received by the xTU-R over all sub carriers during Showtime after the diag…	0.1 dBUnsigned32 Constraints: range: 0-1270 range: 2147483646-2147483647	.1.3.6.1.4.1.2011.6.115.1.2.4.1.3
vdsl2SCStatusBandSnrMargin SNR Margin is the maximum increase in dB of the noise power received at the XTU (xTU-R on downstream direction and xTU-C on upstream direction), such that the BER requirements are met for all bearer channels received at…	0.1 dBInteger32 Constraints: range: -640-630 range: 2147483646-2147483647	.1.3.6.1.4.1.2011.6.115.1.2.4.1.4
vdsl2SCStatusBandUpbokle This parameter is a vector of UPBO electrical length per-band estimates for each supported upstream/downstream band, expressed in dB at 1 MHz (kl0) calculated by the VTU-O/VTU-R, based on separate measurements in the…	0.1 dBUnsigned32 Constraints: range: 0-1280 range: 2047-2047 range: 2147483647-2147483647	.1.3.6.1.4.1.2011.6.115.1.2.4.1.5

The table vdsl2SCStatusSegmentTable contains status parameters
of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers. 
Several objects in the table refer to NSus and NSds. For
G.993.2, the value of NSus and NSds are respectively the indices
of the highest supported upstream and downstream subcarriers
according to the selected implementation profile. For ADSL,
NSus is equal to NSCus-1 and NSds is equal to NSCds-1.
The indexes of this table are ifIndex, vdsl2SCStatusDirection, 
and vdsl2SCStatusSegment.  
One index of this entry is an interface index where the
interface has an ifType of vdsl2(251). The second index of this
entry is the transmission direction. The third index identifies
the specific segment of the sub-carriers status addressed.

vdsl2SCStatusSegmentEntry row .1.3.6.1.4.1.2011.6.115.1.2.5.1

The table vdsl2SCStatusSegmentTable contains status parameters
of VDSL2/ADSL/ADSL2 and ADSL2+ sub-carriers.
Several objects in the table refer to NSus and NSds. For
G.993.2, the value of NSus and NSds are…

Indexes

IF-MIBifIndex vdsl2SCStatusDirection vdsl2SCStatusSegment

Column	Syntax	OID
vdsl2SCStatusSegment The segment of the sub-carriers status information provided by this row. Several status parameters in this table are retrieved in segments. The first segment of the status information is retrieved with vdsl2SCStatusSegm…	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.2011.6.115.1.2.5.1.1
vdsl2SCStatusSegmentLinReal An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a …	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.2
vdsl2SCStatusSegmentLinImg An array of up to 512 complex H(f) linear representation values in linear scale for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a …	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.3
vdsl2SCStatusSegmentLog An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers groups and can be retrieved in a single s…	dBOctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.4
vdsl2SCStatusSegmentQln An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number…	dBm/HzOctetString Constraints: range: 0-512	.1.3.6.1.4.1.2011.6.115.1.2.5.1.5
vdsl2SCStatusSegmentSnr The SNR Margin per sub-carrier group, expressing the ratio between the received signal power and received noise power per sub-scriber group. It is an array of 512 octets, designed for supporting up to 512 (downstream) …	0.5 dBOctetString Constraints: range: 0-512	.1.3.6.1.4.1.2011.6.115.1.2.5.1.6
vdsl2SCStatusSegmentBitsAlloc The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. When more then 512 sub-carriers are supported, the status information is reported …	bitsOctetString Constraints: range: 0-256	.1.3.6.1.4.1.2011.6.115.1.2.5.1.7
vdsl2SCStatusSegmentGainAlloc The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported throu…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.8
vdsl2SCStatusSegmentTssi The transmit spectrum shaping (TSSi) breakpoints expressed as the set of breakpoints exchanged during G.994.1. Each breakpoint is a pair of values occupying 3 octets with the following structure: First 2 octets - Index …	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Tssi Type Constraints: range: 0..96	.1.3.6.1.4.1.2011.6.115.1.2.5.1.9
vdsl2SCStatusSegmentTxPSD The TxPSD per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through multipl…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65535
vdsl2SCStatusSegmentSnrMargin The SnrMargin per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. When more then 512 sub-carriers are supported, the status information is reported through mul…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65536
vdsl2SCStatusSegmentLogScGroupSize Number of sub-carriers per group used to report the H(f) logarithmic representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65537
vdsl2SCStatusSegmentQlnScGroupSize Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is e…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65538
vdsl2SCStatusSegmentLinScGroupSize Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65539
vdsl2SCStatusSegmentSnrScGroupSize Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. For ADSL, this parameter is equal to one and, for VDSL2, it is equal to the si…	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65540
hwvdsl2SCStatusSegmentQlnWithVectoring An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers groups and can be retrieved in a single segment. The number…	dBm/HzOctetString Constraints: range: 0-512	.1.3.6.1.4.1.2011.6.115.1.2.5.1.65541

The table hwVdslSCFextTable contains FEXT coupling function parameters.
The indexes of this table are ifIndex, hwVdslSCFextFromIfindex, 
and hwVdslSCFextRequestXLinScGroupSize.

hwVdslSCFextEntry row .1.3.6.1.4.1.2011.6.115.1.2.6.1

The table hwVdslSCFextTable contains FEXT coupling function parameters.
The indexes of this entry are ifIndex, hwVdslSCFextFromIfindex,
and hwVdslSCFextRequestXLinScGroupSize.

Indexes

IF-MIBifIndex hwVdslSCFextFromIfindex hwVdslSCFextRequestXLinScGroupSize

Column	Syntax	OID
hwVdslSCFextFromIfindex The hwVdslSCFextFromIfindex is an interface index where the interface has an ifType of vdsl2(251).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.6.115.1.2.6.1.1
hwVdslSCFextRequestXLinScGroupSize This parameter is the requested value of XLING. The valid values are 1, 2, 4, 8, 16, 32, and 64.	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8 range: 16-16 range: 32-32 range: 64-64	.1.3.6.1.4.1.2011.6.115.1.2.6.1.2
hwVdslSCFextXLinScaleDs This parameter is the scale factor to be applied to the downstream Xlinpsds values. It is represented as an unsigned integer in the range from 1 to 2^16 - 1.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.6.1.3
hwVdslSCFextXlinScGroupSizeDs This parameter is the number of subcarriers per group used to report Xlinpsds. The valid values are 1, 2, 4, 8, 16, 32, and 64. XLINGds should equal the sub-sampling factor used to estimate the crosstalk channel for …	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8 range: 16-16 range: 32-32 range: 64-64	.1.3.6.1.4.1.2011.6.115.1.2.6.1.4
hwVdslSCFextXLinBandDs XLINBANDSds contains pairs of (start_subcarrier_index, stop_subcarrier_index) for every band in which XLINpsds is reported.	OctetString Constraints: range: 0-96	.1.3.6.1.4.1.2011.6.115.1.2.6.1.5
hwVdslSCFextXlinRealDs For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for downstream FEXT coupling coefficients Xlinds(f) originating from the loop connected to the VCE port k i…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.6.1.6
hwVdslSCFextXlinImgDs For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for downstream FEXT coupling coefficients Xlinds(f) originating from the loop connected to the VCE port k i…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.6.1.7
hwVdslSCFextXLinScaleUs This parameter is the scale factor to be applied to the upstream Xlinpsus values. It is represented as an unsigned integer in the range from 1 to 2^16 - 1.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.2.6.1.8
hwVdslSCFextXlinScGroupSizeUs This parameter is the number of subcarriers per group used to report Xlinpsus. The valid values are 1, 2, 4, 8, 16, 32, and 64. XLINGus should equal the sub-sampling factor used to estimate the crosstalk channel for …	Unsigned32 Constraints: range: 1-2 range: 4-4 range: 8-8 range: 16-16 range: 32-32 range: 64-64	.1.3.6.1.4.1.2011.6.115.1.2.6.1.9
hwVdslSCFextXLinBandUs XLINBANDSus contains pairs of (start_subcarrier_index, stop_subcarrier_index) for every band in which XLINpsus is reported.	OctetString Constraints: range: 0-96	.1.3.6.1.4.1.2011.6.115.1.2.6.1.10
hwVdslSCFextXlinRealUs For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for upstream FEXT coupling coefficients Xlinus(f) originating from the loop connected to the VCE port k int…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.6.1.11
hwVdslSCFextXlinImgUs For each given VCE port index k, this parameter is a one-dimensional array of complex values in linear scale for upstream FEXT coupling coefficients Xlinus(f) originating from the loop connected to the VCE port k int…	OctetString Constraints: range: 0-1024	.1.3.6.1.4.1.2011.6.115.1.2.6.1.12

The table vdsl2LineInventoryTable contains inventory of VDSL2
unit. The indexes of this table are ifIndex and vdsl2LInvUnit.

vdsl2LineInventoryEntry row .1.3.6.1.4.1.2011.6.115.1.3.1.1

The table vdsl2LineInventoryTable contains inventory of VDSL2
unit. The indexes of this entry are ifIndex and vdsl2LInvUnit.

Indexes

IF-MIBifIndex vdsl2LInvUnit

Column	Syntax	OID
vdsl2LInvUnit The termination unit XTUC{1} or XTUR{2}.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.4.1.2011.6.115.1.3.1.1.1
vdsl2LInvG994VendorId The xTU G.994.1 Vendor ID as inserted in the G.994.1 CL/CLR message. It consists of 8 binary octets, including a country code followed by a (regionally allocated) provider code, as defined in Recommendation T.35.	OctetString Constraints: range: 0-8	.1.3.6.1.4.1.2011.6.115.1.3.1.1.2
vdsl2LInvSystemVendorId The xTU System Vendor ID (identifies the xTU system integrator) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It con…	OctetString Constraints: range: 0-8	.1.3.6.1.4.1.2011.6.115.1.3.1.1.3
vdsl2LInvVersionNumber The xTU version number (vendor specific information) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It consists of up…	OctetString Constraints: range: 0-16	.1.3.6.1.4.1.2011.6.115.1.3.1.1.4
vdsl2LInvSerialNumber The xTU serial number (vendor specific information) as inserted in the Overhead Messages (both xTUs for G.992.3 and G.992.4) or in the Embedded Operations Channel (only xTU-R in G.992.1 and G.992.2). It is vendor speci…	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.3.1.1.5
vdsl2LInvSelfTestResult The xTU self-test result, coded as a 32-bit integer. The most significant octet of this object is '0' if the self-test passed, and '1' if the self-test failed. The interpretation of the other octets is vendor discreti…	OctetString Constraints: range: 0-4	.1.3.6.1.4.1.2011.6.115.1.3.1.1.6
vdsl2LInvTransmissionCapabilities The xTU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the xTU supports the respective coding. The valu…	HUAWEI-VDSL2-LINE-TC-MIBVdsl2TransmissionModeType Type Values: 0 ansit1413 1 etsi 2 g9921PotsNonOverlapped 3 g9921PotsOverlapped 4 g9921IsdnNonOverlapped 5 g9921isdnOverlapped 6 g9921tcmIsdnNonOverlapped 7 g9921tcmIsdnOverlapped 8 g9922potsNonOverlapeed 9 g9922potsOverlapped 10 g9922tcmIsdnNonOverlapped 11 g9922tcmIsdnOverlapped 12 g9921tcmIsdnSymmetric 13 reserved1 14 reserved2 15 reserved3 16 reserved4 17 reserved5 18 g9923PotsNonOverlapped 19 g9923PotsOverlapped 20 g9923IsdnNonOverlapped 21 g9923isdnOverlapped 22 reserved6 23 reserved7 24 g9924potsNonOverlapeed 25 g9924potsOverlapped 26 reserved8 27 reserved9 28 g9923AnnexIAllDigNonOverlapped 29 g9923AnnexIAllDigOverlapped 30 g9923AnnexJAllDigNonOverlapped 31 g9923AnnexJAllDigOverlapped 32 g9924AnnexIAllDigNonOverlapped 33 g9924AnnexIAllDigOverlapped 34 g9923AnnexLMode1NonOverlapped 35 g9923AnnexLMode2NonOverlapped 36 g9923AnnexLMode3Overlapped 37 g9923AnnexLMode4Overlapped 38 g9923AnnexMPotsNonOverlapped 39 g9923AnnexMPotsOverlapped 40 g9925PotsNonOverlapped 41 g9925PotsOverlapped 42 g9925IsdnNonOverlapped 43 g9925isdnOverlapped 44 reserved10 45 reserved11 46 g9925AnnexIAllDigNonOverlapped 47 g9925AnnexIAllDigOverlapped 48 g9925AnnexJAllDigNonOverlapped 49 g9925AnnexJAllDigOverlapped 50 g9925AnnexMPotsNonOverlapped 51 g9925AnnexMPotsOverlapped 52 reserved12 53 reserved13 54 reserved14 55 reserved15 56 reserved16 57 reserved17 58 reserved18 59 reserved19 60 reserved20 61 reserved21 62 reserved22 63 reserved23 64 reserved24 65 reserved25 66 reserved26 67 reserved27 68 reserved28 69 reserved29 70 reserved30 71 reserved31 72 g9932AnnexAPots 73 g9932AnnexAIsdn 74 g9932AnnexBPots 75 g9932AnnexBIsdn 76 g9932AnnexCPots 77 g9932AnnexCIsdn 78 g9935 79 g9935FriendlyDs 80 g9935FullFriendly 81 reserved32	.1.3.6.1.4.1.2011.6.115.1.3.1.1.7
vdsl2LInvModelId The XTU model ID.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.3.1.1.8

The table vdsl2PMLineCurrTable contains current Performance
Monitoring results of VDSL2 line.  
The indexes of this table are an interface index where the
interface has an ifType of vdsl2(251) and the termination
unit.

vdsl2PMLineCurrEntry row .1.3.6.1.4.1.2011.6.115.1.4.1.1.1

The table vdsl2PMLineCurrTable contains current Performance
Monitoring results of VDSL2 line.
The indexes of this entry are an interface index where the
interface has an ifType of vdsl2(251) and the termination
unit.

Indexes

IF-MIBifIndex vdsl2PMLCurrUnit

Column	Syntax	OID
vdsl2PMLCurrUnit The termination unit XTUC{1} or XTUR{2}.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.1
vdsl2PMLCurrValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.2
vdsl2PMLCurrInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.3
vdsl2PMLCurr15MTimeElapsed Total elapsed seconds in this interval. Unit: seconds	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.4
vdsl2PMLCurr15MFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.5
vdsl2PMLCurr15MEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >=1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.6
vdsl2PMLCurr15MSes Count of seconds during this interval that there was: xTU-C: If G.998.4 is supported and retransmission is enabled in the near-end received direction, a SES is declared if during a 1-second interval, …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.7
vdsl2PMLCurr15MLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.8
vdsl2PMLCurr15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely-errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.9
vdsl2PMLCurr1DayValidIntervals Valid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.10
vdsl2PMLCurr1DayInvalidIntervals Invalid intervals.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.11
vdsl2PMLCurr1DayTimeElapsed Total elapsed seconds in this interval. Unit: seconds	secondsHC-PerfHist-TC-MIBHCPerfTimeElapsed Type Constraints: range: 0..86399	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.12
vdsl2PMLCurr1DayFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.13
vdsl2PMLCurr1DayEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.14
vdsl2PMLCurr1DaySes Count of seconds during this interval that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.15
vdsl2PMLCurr1DayLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.16
vdsl2PMLCurr1DayUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.17
vdsl2PMLEverBeforeFecs Count of seconds since agent reset that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Huawei defined. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.18
vdsl2PMLEverBeforeEs Count of seconds since agent reset that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR L…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.19
vdsl2PMLEverBeforeSes Count of seconds since agent reset that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.20
vdsl2PMLEverBeforeLoss Count of seconds since agent reset that there was LOS (or LOS-FE for xTU-R). Huawei defined. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.21
vdsl2PMLEverBeforeUas Count of seconds in Unavailability State since agent reset. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored seconds.…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.22
vdsl2PMLCurr15MLofs Count of seconds in the current 15 minute interval when there was Loss of Framing. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.23
vdsl2PMLCurr15MLols Count of seconds in the current 15 minute interval when there was Loss of Link. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.24
vdsl2PMLCurr15MLops Count of seconds in the current 15 minute interval when there was Loss of Power. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.25
vdsl2PMLCurr1DayLofs Count of the number of seconds when there was Loss of Framing during the current day. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.26
vdsl2PMLCurr1DayLols Count of the number of seconds when there was Loss of Link during the current day. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.27
vdsl2PMLCurr1DayLops Count of the number of seconds when there was Loss of Power during the current day. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.28
vdsl2PMLEverBeforeLofs Count of the number of seconds when there was Loss of Framing since agent reset. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.29
vdsl2PMLEverBeforeLols Count of the number of seconds when there was Loss of Link since agent reset. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.30
vdsl2PMLEverBeforeLops Count of the number of seconds when there was Loss of Power since agent reset. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.31
vdsl2PMLCurr15MSosSuccess Count of the total number of successful SOS procedures initiated in the current 15 minute. Unit: times	timesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.32
vdsl2PMLCurr1DaySosSuccess Count of the total number of successful SOS procedures initiated during the current day. Unit: times	timesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.33
vdsl2PMLEverBeforeSosSuccess Count of the total number of successful SOS procedures initiated since agent reset. Unit: times	timesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.34
vdsl2PMLCurr15MInmainpeq This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 15 minutes.	OctetString Constraints: range: 0-68	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.35
vdsl2PMLCurr15MInmame This parameter is a count of the INMAME anomalies occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.36
vdsl2PMLCurr15MInmaiat This parameter is a count of the INMAIATi anomalies occurring on the line during current 15 minutes.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.37
vdsl2PMLCurr1DayInmainpeq This parameter is a count of the INMAINPEQi anomalies occurring on the line during current 1 day.	OctetString Constraints: range: 0-68	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.38
vdsl2PMLCurr1DayInmame This parameter is a count of the INMAME anomalies occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.39
vdsl2PMLCurr1DayInmaiat This parameter is a count of the INMAIATi anomalies occurring on the line during current 1 day.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.40
vdsl2PMLEverBeforeInmainpeq This parameter is a count of the INMAINPEQi anomalies occurring on the line ever before.	OctetString Constraints: range: 0-68	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.41
vdsl2PMLEverBeforeInmame This parameter is a count of the INMAME anomalies occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.42
vdsl2PMLEverBeforeInmaiat This parameter is a count of the INMAIATi anomalies occurring on the line ever before.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.43
vdsl2PMLineCurr15MStartTime Start time of the current 15-minute performance statistics.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.44
vdsl2PMLineCurr1DayStartTime Start time of the current 1-day performance statistics.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.45
vdsl2PMLCurr15MLeftrs If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.46
vdsl2PMLCurr15MEfb If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.47
vdsl2PMLCurr15MMinEftr If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.48
vdsl2PMLCurr1DayLeftrs If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 24 hours accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.49
vdsl2PMLCurr1DayEfb If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 24 hours accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.50
vdsl2PMLCurr1DayMinEftr If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 24 hours accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.51
vdsl2PMLEverBeforeLeftrs If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.52
vdsl2PMLEverBeforeEfb If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.53
vdsl2PMLEverBeforeMinEftr If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.54
hwvdsl2PMLEverBeforeSraDownShiftEvent This parameter is a count of sra downshift event occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.55
hwvdsl2PMLEverBeforeSraUpShiftEvent This parameter is a count of sra upshift event occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.56
hwvdsl2PMLCurr15MSraDownShiftEvent This parameter is a count of sra downshift event occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.57
hwvdsl2PMLCurr15MSraUpShiftEvent This parameter is a count of sra upshift event occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.58
hwvdsl2PMLCurr1DaySraDownShiftEvent This parameter is a count of sra downshift event occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.59
hwvdsl2PMLCurr1DaySraUpShiftEvent This parameter is a count of sra upshift event occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.60
hwvdsl2PMLEverBeforeDisorderLeavingEvent This parameter is a count of disorder leaving event occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.61
hwvdsl2PMLEverBeforeLof This parameter is a count of loss of frame failure occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.62
hwvdsl2PMLEverBeforeLos This parameter is a count of loss of signal failure occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.63
hwvdsl2PMLEverBeforeLop This parameter is a count of loss of power failure occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.64
hwvdsl2PMLEverBeforeLom This parameter is a count of loss of margin failure occurring on the line ever before.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.65
hwvdsl2PMLCurr15MDisorderLeavingEvent This parameter is a count of disorder leaving event occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.66
hwvdsl2PMLCurr1DayDisorderLeavingEvent This parameter is a count of disorder leaving event occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.67
hwvdsl2PMLCurr15MLof This parameter is a count of loss of frame failure occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.68
hwvdsl2PMLCurr15MLos This parameter is a count of loss of signal failure occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.69
hwvdsl2PMLCurr15MLop This parameter is a count of loss of power failure occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.70
hwvdsl2PMLCurr15MLom This parameter is a count of loss of margin failure occurring on the line during current 15 minutes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.71
hwvdsl2PMLCurr1DayLof This parameter is a count of loss of frame failure occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.72
hwvdsl2PMLCurr1DayLos This parameter is a count of loss of signal failure occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.73
hwvdsl2PMLCurr1DayLop This parameter is a count of loss of power failure occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.74
hwvdsl2PMLCurr1DayLom This parameter is a count of loss of margin failure occurring on the line during current 1 day.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.1.1.75

The table vdsl2PMLineCurrInitTable contains current
initialization counters of VDSL2 line. 
The indexes of this table are an interface index where the
interface has an ifType of vdsl2(251) and the termination
unit.

vdsl2PMLineCurrInitEntry row .1.3.6.1.4.1.2011.6.115.1.4.1.2.1

The table vdsl2PMLineCurrInitTable contains current
initialization counters of VDSL2 line.
The indexes of this entry are an interface index where the
interface has an ifType of vdsl2(251) and the termination
unit.

Indexes

IF-MIBifIndex

Column	Syntax	OID
vdsl2PMLCurrInit15MTimeElapsed Total elapsed seconds in this interval. Unit: seconds	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.1
vdsl2PMLCurrInit15MFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.2
vdsl2PMLCurrInit15MFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.3
vdsl2PMLCurrInit15MShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.4
vdsl2PMLCurrInit15MFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.5
vdsl2PMLCurrInit1DayTimeElapsed Total elapsed seconds in this interval. Unit: seconds	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.6
vdsl2PMLCurrInit1DayFullInits Count of full initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.7
vdsl2PMLCurrInit1DayFailedFullInits Count of failed full initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.8
vdsl2PMLCurrInit1DayShortInits Count of short initializations attempted on the line (successful and failed) during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.9
vdsl2PMLCurrInit1DayFailedShortInits Count of failed short initializations on the line during this interval.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.10
vdsl2PMLInitEverBeforeFullInits Count of full initializations attempted on the line (successful and failed) since agent reset. Huawei defined.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.11
vdsl2PMLInitEverBeforeFailedFullInits Count of failed full initializations on the line since agent reset. Huawei defined.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.12
vdsl2PMLInitEverBeforeShortInits Count of short initializations attempted on the line (successful and failed) since agent reset. Huawei defined.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.13
vdsl2PMLInitEverBeforeFailedShortInits Count of failed short initializations on the line since agent reset. Huawei defined.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.14
vdsl2PMLineCurrInit15MStartTime Start time of the current initializations 15-minute performance statistics.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.15
vdsl2PMLineCurrInit1DayStartTime Start time of the current initializations 1-day performance statistics.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.6.115.1.4.1.2.1.16

The table vdsl2PMLineHist15MinTable contains PM line history
for 15min intervals of VDSL2 line.   
The indexes of this table are an interface index where the
interface has an ifType of vdsl2(251), the termination unit,
and an interval number.

vdsl2PMLineHist15MinEntry row .1.3.6.1.4.1.2011.6.115.1.4.1.3.1

The table vdsl2PMLineHist15MinTable contains PM line history
for 15min intervals of VDSL2 line.
The indexes of this entry are an interface index where the
interface has an ifType of vdsl2(251), the termination unit,
and…

Indexes

IF-MIBifIndex vdsl2PMLHist15MUnit vdsl2PMLHist15MInterval

Column	Syntax	OID
vdsl2PMLHist15MUnit The termination unit XTUC{1} or XTUR{2}.	HUAWEI-VDSL2-LINE-TC-MIBVdsl2Unit Type Values: 1 xtuc 2 xtur	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.1
vdsl2PMLHist15MInterval The interval number.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.2
vdsl2PMLHist15MMonitoredTime Total seconds monitored in this interval. Unit: seconds	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.3
vdsl2PMLHist15MFecs Count of seconds during this interval that there was at least one FEC correction event for one or more bearer channels in this line. This parameter is inhibited during UAS or SES. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.4
vdsl2PMLHist15MEs Count of seconds during this interval that there was: xTU-C: CRC-8 >= 1 for one or more bearer channels OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: FEBE >= 1 for one or more bearer channels OR …	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.5
vdsl2PMLHist15MSes Count of seconds during this interval that there was: xTU-C: (CRC-8 summed over all bearer channels) >= 18 OR LOS >= 1 OR SEF >= 1 OR LPR >= 1 xTU-R: (FEBE summed over all bearer channels) >= 18 OR…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.6
vdsl2PMLHist15MLoss Count of seconds during this interval that there was LOS (or LOS-FE for xTU-R). Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.7
vdsl2PMLHist15MUas Count of seconds in Unavailability State during this interval. Unavailability begins at the onset of 10 contiguous severely -errored seconds, and ends at the onset of 10 contiguous seconds with no severely-errored secon…	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.8
vdsl2PMLHist15MValidInterval This variable indicates if the data for this interval is valid.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.9
vdsl2PMLHist15MLofs Count of seconds in the interval when there was Loss of Framing. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.10
vdsl2PMLHist15MLols Count of seconds in the interval when there was Loss of Link. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.11
vdsl2PMLHist15MLops Count of seconds in the interval when there was Loss of Power. Unit: seconds	secondsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.12
vdsl2PMLHist15MSosSuccess Count of the total number of successful SOS procedures initiated in the interval. Unit: times	timesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.13
vdsl2PMLHist15MInmainpeq This parameter is a count of the INMAINPEQi anomalies occurring on the line over the 15 minutes accumulation period.	OctetString Constraints: range: 0-68	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.14
vdsl2PMLHist15MInmame This parameter is a count of the INMAME anomalies occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.15
vdsl2PMLHist15MInmaiat This parameter is a count of the INMAIATi anomalies occurring on the line over the 15 minutes accumulation period.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.16
vdsl2PMLHist15MStartTime Start time of the historical 15-minute performance statistics.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.17
vdsl2PMLHist15MLeftrs If retransmission is used in a given transmit direction, this parameter is a count of the seconds with a near-end leftr defect present observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.18
vdsl2PMLHist15MEfb If retransmission is used in a given transmit direction, this parameter is a count of the number of error-free bits observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.19
vdsl2PMLHist15MMinEftr If retransmission is used in a given transmit direction, this parameter reports the minimum of the EFTR(Error-free throughput rate) observed over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.20
hwvdsl2PMLHist15MSraDownShiftEvent This parameter is a count of sra downshift event occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.21
hwvdsl2PMLHist15MSraUpShiftEvent This parameter is a count of sra upshift event occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.22
hwvdsl2PMLHist15MDisorderLeavingEvent This parameter is a count of disorder leaving event occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.23
hwvdsl2PMLHist15MLof This parameter is a count of loss of frame failure occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.24
hwvdsl2PMLHist15MLos This parameter is a count of loss of signal failure occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.25
hwvdsl2PMLHist15MLop This parameter is a count of loss of power failure occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.26
hwvdsl2PMLHist15MLom This parameter is a count of loss of margin failure occurring on the line over the 15 minutes accumulation period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.6.115.1.4.1.3.1.27