HUAWEI-PORT-MIB Table View

This table describes the access and configuration of physical attributes of various Ethernet interfaces.

hwEthernetEntry row .1.3.6.1.4.1.2011.5.25.157.1.1.1.1

Indicates the physical attributes of the Ethernet interface.
This table lists the physical attributes of various Ethernet interfaces.

Indexes

hwEthernetIfIndex

Column	Syntax	OID
hwEthernetIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.1
hwEthernetLoopback This object indicates the internal loop (local loopback) function, which is used to test a local interface. When the interface works normally, the local loopback function must be disabled. By default, stopLoopback is se…	Enumerationr/w Enumerated Values: 1 otherLoop 2 stopLoopback 3 local 4 remote	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.11
hwEthernetPortType This object indicates the type of an Ethernet interface, either the optical interface or the electrical interface.	Enumerationr/w Enumerated Values: 1 other 2 copper 3 fiber	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.12
hwEthernetSpeedSet This object indicates the transmission rate of the Ethernet interface. You can configure transmission rates for only certain Ethernet electrical interfaces, and you cannot configure transmission rates for optical interf…	Enumerationr/w Enumerated Values: 1 other 2 speed10 3 speed100 4 speed1000 5 speed10000 6 speed40000 7 speed20000 8 speed2500 9 speed5000 10 speed100000 11 speed12000 12 speed48000 13 speed25000 14 speed50000 15 speed200000 16 speed400000 17 speed12500	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.13
hwEthernetDuplex This object indicates the duplex mode of an Ethernet interface. Ethernet electrical interfaces can work in either half-duplex or full-duplex mode. Ethernet optical interfaces can work only in full-duplex mode.	Enumerationr/w Enumerated Values: 1 full 2 half	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.14
hwEthernetNegotiation This object indicates whether auto-negotiation is enabled on an Ethernet electrical interface. The default value is enable. For an Ethernet electrical interface, hwEthernetSpeedSet, hwEthernetDuplex, and hwEthernetNego…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.15
hwEthernetPortTypeOperate This object indicates the link type of an Ethernet interface, either optical fibers or cables. This object is only supported by certain Ethernet interfaces.	Enumerationr/w Enumerated Values: 1 other 2 copper 3 fiber100 4 fiber1000	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.16
hwEthernetClock This object indicates the clock mode. By default, the slave clock mode is used. Only WAN interfaces require the clock configuration.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.20
hwEthernetFlagJ0Mode This object indicates that 10GE WAN interfaces have to use SDH/SONET as the frame format and the overhead byte has to be set. The overhead byte of an SDH frame can be: j0: indicates the section trace byte. The default v…	Enumerationr/w Enumerated Values: 1 j01ByteMode 2 j016ByteMode 3 j064ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.21
hwEthernetFlagJ0Value This object indicates that when hwEthernetFlagJ0Mode is set to j01ByteMode, this object takes effect.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.22
hwEthernetFlagJ0Trace This object indicates the section trace byte. When hwEthernetFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this object takes effect. When hwEthernetFlagJ0Mode is set to j016ByteMode, the value of hwEthernetFl…	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.23
hwEthernetFlagJ1Mode This object indicates the overhead byte of an SDH frame. j1 indicates the path trace byte. By default, the value is j116ByteMode(2): hwEthernetFlagJ1Trace: NetEngine.	Enumerationr/w Enumerated Values: 1 j11ByteMode 2 j116ByteMode 3 j164ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.24
hwEthernetFlagJ1Value This object indicates that when hwEthernetFlagJ1Mode is set to j11ByteMode, this object takes effect.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.25
hwEthernetFlagJ1Trace This object indicates the path trace byte. When hwEthernetFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this object takes effect. When hwEthernetFlagJ1Mode is set to j116ByteMode, the value of this object is …	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.26
hwEthernetFlagC2Value This object indicates the overhead byte of the SDH frame. C2: indicates the path signal label byte. The value ranges from 00 to FF, in the hexadecimal format. The default value is 26 (0x1a).	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.27
hwEthernetUpHoldTime This object indicates the time period during which the interface remains Up.	Integer32r/w Constraints: range: 0-86400000	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.31
hwEthernetDownHoldTime This object indicates the time period during which the interface remains Down.	Integer32r/w Constraints: range: 0-86400000	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.32
hwEthernetSubinterfaceStatisticEnable This object indicates statistics collection is enabled for a sub-interface.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.33
hwEthernetFlowControl This object indicates the interface flow control status.	Enumerationr/w Enumerated Values: 1 receive 2 send 3 both 4 none 5 default	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.34
hwEthernetOffline This object indicates that the physical protocol status of an interface is Down.	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.35
hwEthernetSetTransferMode This object indicates the LAN-WAN mode of an Ethernet interface.	Enumerationr/w Enumerated Values: 1 lan 2 wan 3 none 4 otn 5 flexe	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.36
hwEthernetJumboframeMaxLength This object indicates the maximum length of the Jumbo frame on an interface.	Integer32r/w Constraints: range: 1518-16000	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.37
hwEthernetComboType combo mode of this port.	Enumerationr/w Enumerated Values: 1 auto 2 copper 3 fiber 4 other	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.38
hwEthernetPortMode Indicates combo mode of this port.	Enumeration Enumerated Values: 1 copper 2 fiber 3 other	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.39
hwEthernetNegotiationMode Set negotiation-mode for phy of electronic GE port.The mode is uesed for synchronizing clock.	Enumerationr/w Enumerated Values: 1 notsupport 2 auto 3 master 4 slave	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.40
hwEthernetCarrierTransitions Number of times the interface state has transitioned from up to down since the time the device restarted.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.1.1.1.41

This table describes the access and configuration of physical attributes of various POS interfaces.

hwPosEntry row .1.3.6.1.4.1.2011.5.25.157.1.2.1.1

Indicates the physical attributes of the POS interface.
This table lists the physical attributes of the POS interface.

Indexes

hwPosIfIndex

Column	Syntax	OID
hwPosIfIndex Interface index(es) of port(s) present on the device .	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.1
hwPosLinkProtocol This object indicates the link layer protocol running on a POS interface. By default, a POS interface uses PPP as the link layer protocol.	Enumerationr/w Enumerated Values: 1 ietf 2 nonstandard 3 hdlc 4 ppp 5 fr	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.11
hwPosFrameFormat This object indicates the frame type on a POS interface. By default, the frame type is SDH.	Enumerationr/w Enumerated Values: 1 sonet 2 sdh	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.12
hwPosLoopback This object indicates the internal loop (local loopback) function on a POS interface, which is used to test a local interface. When the interface works normally, the local loopback function must be disabled. By default…	Enumerationr/w Enumerated Values: 1 otherLoop 2 stopLoopback 3 local 4 remote	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.13
hwPosScramble This object indicates whether the payload scramble function is enabled on a POS interface. By default, the scramble function is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.14
hwPosClock This object indicates the clock mode. By default, the slave clock mode is used.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.15
hwPosCrcVerifyCode This object indicates the length of the CRC field. By default, the length is 32.	Enumerationr/w Enumerated Values: 1 crc16 2 crc32	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.16
hwPosFlagJ0Mode This object indicates the overhead byte of an SDH frame. The value can be: j0: indicates the section trace byte. The default value is j016ByteMode(2). hwEthernetFlagJ0Trace: NetEngine.	Enumerationr/w Enumerated Values: 1 j01ByteMode 2 j016ByteMode 3 j064ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.21
hwPosFlagJ0Value This object indicates that when hwPosFlagJ0Mode is set to j01ByteMode, this object takes effect.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.22
hwPosFlagJ0Trace This object indicates the section trace byte. When hwPosFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this object takes effect. When hwPosFlagJ0Mode is set to j016ByteMode, the value of hwPosFlagJ0Mode is up…	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.23
hwPosFlagJ1Mode This object indicates the overhead byte of an SDH frame. j1 indicates the path trace byte. The default value is j116ByteMode(2). hwPosFlagJ1Trace: NetEngine.	Enumerationr/w Enumerated Values: 1 j11ByteMode 2 j116ByteMode 3 j164ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.24
hwPosFlagJ1Value This object indicates the j1-1byte-mode value. When hwPosFlagJ1Mode is set to j11ByteMode, this object takes effect.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.25
hwPosFlagJ1Trace This object indicates the path trace byte. When hwPosFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this object takes effect. When hwPosFlagJ1Mode is set to j116ByteMode, the value of hwPosFlagJ1Mode is up to…	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.26
hwPosFlagC2Value This object indicates the overhead byte of an SDH frame. C2 indicates the path signal label byte. The value ranges from 00 to FF in the hexadecimal format. The default value is 22 (0x16).	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.2.1.1.27

Indicates the physical attributes of the CPOS interface.
This table lists the physical attributes of the CPOS interface.

hwCposEntry row .1.3.6.1.4.1.2011.5.25.157.1.3.1.1

Indicates the physical attributes of the CPOS interface.
This table lists the physical attributes of the CPOS interface.

Indexes

hwCposIfIndex

Column	Syntax	OID
hwCposIfIndex Interface index(es) of port(s) present on the device .	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.1
hwCposClock Indicates whether the clock is in master mode or slave mode. By default, the clock is in slave mode.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.11
hwCposIfType Indicates the interface type.	Enumerationr/w Enumerated Values: 1 stm1 2 stm16	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.12
hwCposFrameFormat Indicates the frame type of the CPOS interface. By default, the frame type of the CPOS interface is SDH.	Enumerationr/w Enumerated Values: 1 sonet 2 sdh	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.13
hwCposMultiplex Indicates the multiplex mode of the AUG. By default, the multiplex mode of the AUG is au-4.	Enumerationr/w Enumerated Values: 1 au3 2 au4	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.14
hwCposLoopback Indicates the loopback function of the CPOS interface. By default, the loopback function is disabled.	Enumerationr/w Enumerated Values: 1 otherloop 2 stopLoopback 3 local 4 remote	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.15
hwCposFlagJ0Mode Indicates the overhead byte of the SDH frame. j0: sets section trace byte. The default value is j016ByteMode(2);hwCposFlagJ0Trace NetEngine.	Enumerationr/w Enumerated Values: 1 j01ByteMode 2 j016ByteMode 3 j064ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.21
hwCposFlagJ0Value j01ByteMode Value . When hwCposFlagJ0Mode is set to j01ByteMode, hwCposFlagJ0Value takes effect.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.22
hwCposFlagJ0Trace Set section trace byte. When hwCposFlagJ0Mode is set to j016ByteMode or j064ByteOrNullMode, this variable takes effect. When hwCposFlagJ0Mode is set to j016ByteMode, this variable is up to 15 characters trace byte. When…	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.23
hwCposFlagJ1Mode Indicates the overhead byte of the SDH frame. j1: sets path trace byte. The default value is j116ByteMode(2);hwCposFlagJ1Trace NetEngine.	Enumerationr/w Enumerated Values: 1 j11ByteMode 2 j116ByteMode 3 j164ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.24
hwCposFlagJ1Value Indicates the value of j11ByteMode. When hwCposFlagJ1Mode is set to j11ByteMode, hwCposFlagJ1Value takes effect.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.25
hwCposFlagJ1Trace Set path trace byte. When hwCposFlagJ1Mode is set to j116ByteMode or j164ByteOrNullMode, this variable takes effect. When hwCposFlagJ1Mode is set to j116ByteMode, this variable is a string up to 15 characters trace byte…	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.26
hwCposFlagC2Value Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.27
hwCposB1SdAlarmThreshold The threshold of B1 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.28
hwCposB1ExcAlarmThreshold The threshold of B1 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.29
hwCposB2SdAlarmThreshold The threshold of B2 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.30
hwCposB2ExcAlarmThreshold The threshold of B2 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.31
hwCposB3SdAlarmThreshold The threshold of B3 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.32
hwCposB3ExcAlarmThreshold The threshold of B3 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.33
hwCposLpBipSdAlarmThreshold The threshold of BIP2 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.34
hwCposLpBipExcAlarmThreshold The threshold of BIP2 threshold crossing alarm.	Integer32r/w Constraints: range: 1-9	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.35
hwCposHighPathNumber Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.36
hwCposLowPathNumber Indicates the overhead byte of the SDH frame. c2: indicates the signal label byte. It is a hexdecimal value ranging from 00 to FF. The default value is 22(0x16).	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.37
hwCposMappingMode Indicates the mapping mode of cpos port, default if h-mode(1).	Enumerationr/w Enumerated Values: 1 hMode 2 lMode 3 aMode	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.38
hwCposRxJ0Mode Indicates the received J0 mode.	Enumeration Enumerated Values: 1 j01ByteMode 2 j016ByteMode 3 j064ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.39
hwCposRxJ1Mode Indicates the received J1 mode.	Enumeration Enumerated Values: 1 j11ByteMode 2 j116ByteMode 3 j164ByteOrNullMode 4 peer	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.40
hwCposRxJ0Value Indicates the received J0 value of 1-byte mode.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.41
hwCposRxJ1Value Indicates the received J1 value of 1-byte mode.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.42
hwCposRxJ0Trace Indicates the received J0 characters of 16-byte or 64-byte mode.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.43
hwCposRxJ1Trace Indicates the received J1 characters of 16-byte or 64-byte mode.	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.44
hwCposVc4Flag The value of this object identifies whether a VC4 channel can be created on the CPOS interface. 0 indicates that no VC4 channel can be created on the CPOS interface. 1 indicates that a VC4 channel can be created but ha…	Integer32 Constraints: range: 0-2	.1.3.6.1.4.1.2011.5.25.157.1.3.1.1.45

Description.

hwCposLpEntry row .1.3.6.1.4.1.2011.5.25.157.1.3.4.1

Description.

Indexes

hwCposLpIfIndex hwCposLpId

Column	Syntax	OID
hwCposLpIfIndex Description.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.1
hwCposLpId Description.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.2
hwCposFlagJ2Mode Description.	Enumerationr/w Enumerated Values: 1 j21ByteMode 2 j216ByteMode	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.3
hwCposFlagJ2Value Description.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.4
hwCposFlagJ2Trace Description.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.5
hwCposRxJ2Mode Indicates the received J2 mode.	Enumeration Enumerated Values: 1 j21ByteMode 2 j216ByteMode	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.6
hwCposRxJ2Value Indicates the received J2 value of 1-byte mode.	Integer32 Constraints: range: 0-127	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.7
hwCposRxJ2Trace Indicates the received J2 characters of 16-byte or 64-byte mode.	OctetString Constraints: range: 0-16	.1.3.6.1.4.1.2011.5.25.157.1.3.4.1.8

This table is used to bundle timeslots of CE1/CT1 interfaces.

hwDs0ChannelBundleEntry row .1.3.6.1.4.1.2011.5.25.157.1.4.1.1

This table is used to bundle timeslots of CE1/CT1 interfaces.

Indexes

hwDs0ChannelBundleParentIfIndex hwDs0ChannelBundleDs1ChannelId hwDs0ChannelBundleId

Column	Syntax	OID
hwDs0ChannelBundleParentIfIndex Indicates the index of the parent interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.1
hwDs0ChannelBundleDs1ChannelId Indicates the channel ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.2
hwDs0ChannelBundleId Indicates the index number of the channel set.	Integer32 Constraints: range: 0-30	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.3
hwDs0ChannelBundleIfIndex Indicates the index of the serial interface formed by the timeslot binding.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.11
hwDs0ChannelBundleTimeSlots Indicates the number of the range of the timeslot to be bound. The value is an integer ranging from 0 to 31. Multiple timeslots are separated by ','. The range of timeslot is expressed by using '-'. For E1 card mode: If…	OctetStringr/w Constraints: range: 0-61	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.12
hwDs0ChannelBundleSpeed Configures the mode to configure the timeslots. If the parameter 56 k is selected, the timeslots are bound in the mode of N x 56 kbit/s. If the parameter 64 k is selected, the timeslots are bound in the mode of N x 64 k…	kilo bytesEnumerationr/w Enumerated Values: 1 s56 2 s64 3 s150336	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.13
hwDs0ChannelBundleTimeSlot0 Indicates the timeslot0 to be bound or a single channel. The ture value indicates it will be create TDM channel.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.14
hwDs0ChannelBundleIsMasterPW Indicates if the pw configed on this port is master pw.	Enumeration Enumerated Values: 0 notacrpw 1 masterpw 2 notmasterpw	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.15
hwDs0ChannelBundleMasterPWStatus Indicates the status of master pw.	Enumeration Enumerated Values: 0 unlock 1 lock	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.16
hwDs0ChannelBundlePortName Port name.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.17
hwDs0ChannelBundleRowStatus This variable is used to create or delete an object.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.4.1.1.51

This table lists all E1/CE1 interfaces or T1/CT1 interfaces.
After the mode of E3/CE3 interfaces or T3/CT3 interfaces is set to channelized, this table can be used
to create E1/CE1, or T1/CT1, or E3/CE3, or T3/CT3 interfaces.

hwDs1Entry row .1.3.6.1.4.1.2011.5.25.157.1.5.1.1

This table lists all E1/CE1 interfaces or T1/CT1 interfaces.
After the mode of E3/CE3 interfaces or T3/CT3 interfaces is set to channelized, this table can be used
to create E1/CE1, or T1/CT1, or E3/CE3, or T3/CT3 inter…

Indexes

hwDs1ParentIfIndex hwDs1ChannelId hwDs1IfIndex

Column	Syntax	OID
hwDs1ParentIfIndex Indicates the index of the parent interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.1
hwDs1ChannelId Indicates the channel ID.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.2
hwDs1IfIndex Indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.3
hwDs1ChannelType Indicates the interface type. The type can be E1/CE1 or T1/CT1.	Enumerationr/w Enumerated Values: 1 t1 2 e1	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.11
hwDs1IfType Indicates the interface tyep. e3: is multiplexed by CE3 interfaces. t3: is multiplexed by CT3 interfaces. cpos: is multiplexed by CPOS interfaces. atm: is multiplexed by ATM interfaces. none: indicates the physical inte…	Enumerationr/w Enumerated Values: 1 e3 2 t3 3 cpos 4 atm 255 none	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.12
hwDs1Channelized Indicates the working mode of the interface. true: indicates the channelized mode. false: indicates the clear channel mode. The default is true.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.13
hwDs1CodeType Indicates the code type of the interface. ami: is short for Alternate Mark Inversion. hdb3: is short for High Density Bipolar of Order 3. b8zs: is short for Bipolar with 8-Zero Substitution. none: is not supported	Enumerationr/w Enumerated Values: 1 ami 2 hdb3 3 b8zs 255 none	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.14
hwDs1Clock Indicates the clock mode of the interface. master: indicates that the clock works in master mode and uses the internal clock signal. slave: indicates that the clock works in slave mode and uses the line clock signal.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.15
hwDs1FrameFormat Indicates the frame format of the interface. crc4: indicates that the frame format is CRC4. no-crc4: indicates that the frame format is no-CRC4. sf: indicates that the frame format is Super Frame. esf: indicates that th…	Enumerationr/w Enumerated Values: 1 esf 2 sf 3 noCrc4 4 crc	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.16
hwDs1Cable The cable command takes effect only if the E1 interface card uses 75-ohm coaxial cable. The default is short. If no cable is connected, this parameter is displayed as null.	Enumerationr/w Enumerated Values: 1 long 2 short 255 none	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.17
hwDs1Loopback Enable the loopback function of the interface. local: enables the local loopback on the interface. remote: enables the remote loopback on the interface. payload: enables the remote payload loopback on the interface. cel…	Enumerationr/w Enumerated Values: 1 local 2 remote 3 payload 4 cell 255 none	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.18
hwDs1ClockRecoveryDomain Indicates the clock recovery domain of the interface.	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.19
hwDs1PWClockDomain Indicates the clock recovery domain of the interface.	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.20
hwDs1WorkMode Indicates the clock recovery domain of the interface.	Integer32 Constraints: range: 0-8	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.21
hwDs1EsAlarmTriggerThreshold The trigger threshold of code violation count threshold crossing alarm of E1 line side .	Integer32r/w Constraints: range: 1-900	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.22
hwDs1EsAlarmResumeThreshold The resume threshold of code violation count threshold crossing alarm of E1 line side .	Integer32r/w Constraints: range: 1-900	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.23
hwDs1RowStatus This variable is used to create or delete an object.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.51
hwDs1Lbo The lbo of T1 port. Unit: db. the value is expanded 10 times,so the real value should be reduced 10 times	Enumerationr/w Enumerated Values: 1 db75 2 db155 3 db225 4 none 5 notsupport	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.52
hwDs1CableLength The cableLength of T1 port. Unit: feet.	Enumerationr/w Enumerated Values: 1 length133 2 length266 3 length399 4 length533 5 length655 6 notsupport 255 none	.1.3.6.1.4.1.2011.5.25.157.1.5.1.1.53

This table lists all E3/CE3 interfaces or all T3/CT3 interfaces.

hwDs3Entry row .1.3.6.1.4.1.2011.5.25.157.1.6.1.1

This table lists all E3/CE3 interfaces or all T3/CT3 interfaces.

Indexes

hwDs3ParentIfIndex hwDs3ChannelId hwDs3IfIndex

Column	Syntax	OID
hwDs3ParentIfIndex Indicates the index of the parent interface.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.1
hwDs3ChannelId Indicates the index of the parent interface.	Integer32 Constraints: range: 0-3	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.2
hwDs3IfIndex Indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.3
hwDs3ChannelType Indicates the interface type. The type can be E3/CE3 or T3/CT3.	Enumerationr/w Enumerated Values: 1 t3 2 e3	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.11
hwDs3IfType Indicates the parent interface type of the interface. cpos: is multiplexed by CPOS interfaces. none: indicates the interface is a physical interface. The default is none.	Enumerationr/w Enumerated Values: 1 cpos 255 none	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.12
hwDs3Channelized Indicates the working mode of the interface. true: indicates the channelized mode. false: indicates the clear channel mode. The default is true.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.13
hwDs3Clock Indicates the clock mode of the interface. master: indicates that the clock works in master mode and uses the internal clock signal. slave: indicates that the clock works in slave mode and uses the line clock signal.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.14
hwDs3FrameFormat Indicates the frame format of the interface.	Enumerationr/w Enumerated Values: 1 g832Adm 2 g751Adm 3 g751Plcp 4 cbitAdm 5 cbitPlcp 6 m23Adm 7 m23Plcp	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.15
hwDs3Scramble Indicates the scramble function of the interface. true: enables the scramble function. false: disables the scramble function. The default is false.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.16
hwDs3Cable The cable command takes effect only if the E3 interface card uses 75-ohm coaxial cable. The default is short. If no cable is connected, this parameter is displayed as null.	Enumerationr/w Enumerated Values: 1 long 2 short	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.17
hwDs3NationalBit Indicates the national bit of the E3/CE3 interface. n0: indicates the national bit is 0 and the interface supports only the communication within a country. n1: indicates the national bit is 1 and the interface supports …	Enumerationr/w Enumerated Values: 1 n0 2 n1	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.18
hwDs3Loopback Enable the loopback function of the interface. local: enables the local loopback on the interface. remote: enables the remote loopback on the interface. payload: enables the remote payload loopback on the interface. cel…	Enumerationr/w Enumerated Values: 1 local 2 remote 3 payload 4 cell 255 none	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.19
hwDs3CreateSerial Create serial interface from Ds3 interface. True create serial interface. False destroy serial interface.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.20
hwDs3RowStatus This variable is used to create or delete an object.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.6.1.1.51

Indicates the attribute of the serial interface formed by timeslots.
This table lists the physical attributes of the serial interface.

hwBundleSerialEntry row .1.3.6.1.4.1.2011.5.25.157.1.7.1.1

Indicates the attribute of the serial interface formed by timeslots.
This table lists the physical attributes of the serial interface.

Indexes

hwBundleSerialIfIndex

Column	Syntax	OID
hwBundleSerialIfIndex Interface index(es) of serial(s) present on the device .	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.7.1.1.1
hwBundleSerialLinkProtocol The link-protocol of interface. The serial(s) always use PPP as its link-protocol for default.	Enumerationr/w Enumerated Values: 1 ietf 2 nonstandard 3 hdlc 4 ppp 5 lapb 6 atm 7 tdm 255 none	.1.3.6.1.4.1.2011.5.25.157.1.7.1.1.11
hwBundleSerialTimerHold Indicates the interval for sending Keepalive packets from the serial interface to the peer. The default is 10 seconds.	Integer32r/w Constraints: range: 0-32767	.1.3.6.1.4.1.2011.5.25.157.1.7.1.1.12
hwBundleSerialLoopback true: enables the loopback on the serial interface. false: disables the loopback on the serial interface. By default, the loopback on the serial interface is disabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.5.25.157.1.7.1.1.13
hwBundleSerialCrcVerifyCode Indicates the length of the CRC verify code. The default is 32.	Enumerationr/w Enumerated Values: 1 crc16 2 crc32	.1.3.6.1.4.1.2011.5.25.157.1.7.1.1.14

This table describes the access and configuration of attributes of various physical interfaces.

hwPhysicalPortEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.1.1

Indicates the attribute of the physical port.

Indexes

hwPhysicalPortIfIndex

Column	Syntax	OID
hwPhysicalPortIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.1
hwPhysicalPortDelayTime This object indicates the interface delay. The default value is 0 ms.	Unsigned32r/w Constraints: range: 0-86400000	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.2
hwPhysicalPortDelayRemainTime This object indicates the remaining time after the interface delay is enabled. The value is in milliseconds.	Unsigned32 Constraints: range: 0-86400000	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.3
hwPhysicalPortName Indicates the physical port name.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.4
hwPhysicalPortInChassis Indicates the physical port in chassis.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.5
hwPhysicalPortInSlot Indicates the SlotID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.6
hwPhysicalPortInCard Indicates the CardID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.7
hwPhysicalPortInPort Indicates the PortID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.8
hwPhysicalAutoShutLaserEnable This object indicates the automatic disabling of LASER. By default, automatic disabling of LASER is not supported.	Enumerationr/w Enumerated Values: 1 enable 2 disable 255 notsupport	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.9
hwPhysicalAutoShutLaserOpenInterval This object indicates the enabling interval for the automatic disabling of LASER. The default value is 2000 ms. The value 2147483647 indicates that the interface does not support this function.	Integer32r/w Constraints: range: 100-300 range: 2147483647-2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.10
hwPhysicalAutoShutLaserCloseInterval This object indicates the disabling interval for the automatic disabling of LASER. The default value is 60000 ms. The value 2147483647 indicates that the interface does not support this function.	Integer32r/w Constraints: range: 200-30000 range: 2147483647-2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.11
hwPhysicalAutoShutLaserLongOpenInterval This object indicates the long enabling interval for the automatic disabling of LASER. The default value is 90000 ms. The value 2147483647 indicates that the interface does not support this function.	Integer32r/w Constraints: range: 200-30000 range: 2147483647-2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.12
hwPhysicalLoopbackType This object indicates the current interface status.	Enumeration Enumerated Values: 0 stopLoopback 1 local 2 remote	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.13
hwPhysicalShutLaser This object indicates whether the LASER function is enabled or not.	Enumerationr/w Enumerated Values: 1 off 2 on 255 notsupport	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.14
hwPhysicalLaserStatus This object indicates the LASER status.	Enumeration Enumerated Values: 1 off 2 on 3 offline 255 notsupport	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.15
hwPhysicalPortHoldUp This object indicates whether the interface is Up.	Enumerationr/w Enumerated Values: 0 disable 1 enable	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.16
hwPhysicalPortAlarmInverseEnable Config port alarm inverse enable.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.17
hwPhysicalPortInVsId VsId.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.18
hwPhysicalPortAlarmName Indicates the physical port alarm name.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.19
hwInputRateChangeThresholdPercent Indicates the threshold for the input rate change, in percentage.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.20
hwOutputRateChangeThresholdPercent Indicates the threshold for the output rate change, in percentage.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.21
hwCurrentStatisticalPeriodRate Indicates the rate in the current statistical period.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.22
hwLastStatisticalPeriodRate Indicates the rate in the last statistical period.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.23
hwPortPhysicalRate Indicates the current physical rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.24
hwLicenseType Indicates the type of interface function-controlled license.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.25
hwMaxPortNum Indicates the Maximum number of available interfaces	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.26
hwUsedPortNum Indicates the Number of interfaces in use.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.27
hwPhysicalPortMode The current state of portMode in port.	Enumeration Enumerated Values: 0 eth1g 1 eth10g 2 ethge 3 ethgf 25 eth25g 50 eth50g 100 eth100g	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.28
hwScadaGroupId Indicates the scada group ID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.29
hwPhysicalPortGroupID Indicates the physical port group ID.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.30
hwPortTransModeReasonDescr Indicates the physical port transmission mode different reason.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.31
hwAcBlockReason Indicates the AC block reason.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.32
hwPhysicalPortLocalPhyNum Indicates the local physical port phy number.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.33
hwPhysicalPortRemotePhyNum Indicates the remote physical port phy number.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.34
hwPhysicalPortLocalGroupID Indicates the local physical port groupID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.35
hwPhysicalPortRemteGroupID Indicates the remote physical port groupID.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.36
hwPhysicalPortBW Indicates the local port bandwidth	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.37
hwPhysicalPortList Indicates the physical port list	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.38
hwPhysicalPortPortType Indicates the physical port type	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.39
hwPhysicalPortAlarmReason Indicates the physical port alarm reason	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.40
hwInputDiscardEnable Indicates whether input discard traps should be generated for this physical port. By default, the value is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.41
hwInputDiscardThreshold Indicates the physical port input discard threshold, the default is 3000 packets	Unsigned32r/w Constraints: range: 100-4294967295	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.42
hwInputDiscardInterval Indicates the physical port input discard interval, it must be a multiple of 10, the default is 300 seconds	Integer32r/w Constraints: range: 60-86400	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.43
hwInputDiscardStatistics Indicates the physical port input discard statistics	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.44
hwOutputDiscardEnable Indicates whether output discard traps should be generated for this physical port. By default, the value is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.45
hwOutputDiscardThreshold Indicates the physical port output discard threshold, the default is 3000 packets	Unsigned32r/w Constraints: range: 100-4294967295	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.46
hwOutputDiscardInterval Indicates the physical port output discard interval, it must be a multiple of 10, the default is 300 seconds	Integer32r/w Constraints: range: 60-86400	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.47
hwOutputDiscardStatistics Indicates the physical port output discard statistics	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.48
hwBandwidthLast Indicates the physical port last bandwidth.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.49
hwBandwidthCurrent Indicates the physical port current bandwidth.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.1.1.50

This table describes functions of physical interfaces.

hwSDHRsMsPerfCurrentEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.2.1

Indicates the performance stat of the Regenerator Section.

Indexes

hwSDHRsMsPerfCurrentIfIndex hwSDHRsMsPerfCurrentDataIndex

Column	Syntax	OID
hwSDHRsMsPerfCurrentIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.1
hwSDHRsMsPerfCurrentDataIndex This object indicates the data index.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.2
hwSDHRsPerfCurrentBBE This object indicates the regenerator section (RS) background block error.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.3
hwSDHRsPerfCurrentES This object indicates the number of seconds that the RS error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.4
hwSDHRsPerfCurrentSES This object indicates the number of seconds that the severe RS error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.5
hwSDHRsPerfCurrentUAS This object indicates the number of seconds that the RS does not exist.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.6
hwSDHMsPerfCurrentBBE This object indicates the multi-section background block error.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.7
hwSDHMsPerfCurrentES This object indicates the number of seconds that the multi-section error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.8
hwSDHMsPerfCurrentSES This object indicates the number of seconds that the severe multi-section error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.9
hwSDHMsPerfCurrentUAS This object indicates the number of seconds that the multi-section does not exist.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.10
hwSDHMsPerfCurrentFEBBE This object indicates the multi-section remote background block error.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.11
hwSDHMsPerfCurrentFEES This object indicates the number of seconds that the multi-section remote error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.12
hwSDHMsPerfCurrentFESES This object indicates the number of seconds that the severe multi-section remote error lasts.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.13
hwSDHMsPerfCurrentFEUAS This object indicates the number of seconds that the multi-section remote error does not exist.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.2.1.14

This table describes functions of physical interfaces.

hwSDHHpPerfCurrentEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.3.1

Indicates the performance stat of the Higher order Path.

Indexes

hwSDHHpPerfCurrentIfIndex hwSDHHpPerfCurrentHpIndex hwSDHHpPerfCurrentDataIndex

Column	Syntax	OID
hwSDHHpPerfCurrentIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.1
hwSDHHpPerfCurrentHpIndex This object indicates the higher order path (HP) index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.2
hwSDHHpPerfCurrentDataIndex This object indicates the data index.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.3
hwSDHHpPerfCurrentBBE This object indicates the background errored block of the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.4
hwSDHHpPerfCurrentES This object indicates the number of errored seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.5
hwSDHHpPerfCurrentSES This object indicates the number of severe errored seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.6
hwSDHHpPerfCurrentUAS This object indicates the number of unavailable seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.7
hwSDHHpPerfCurrentFEBBE This object indicates the remote background errored block on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.8
hwSDHHpPerfCurrentFEES This object indicates the number of remote errored seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.9
hwSDHHpPerfCurrentFESES This object indicates the number of severe remote errored seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.10
hwSDHHpPerfCurrentFEUAS This object indicates the number of remote unavailable seconds on the HP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.3.1.11

This table describes the access and configuration of physical attributes of lower order paths (LPs).

hwSDHLpPerfCurrentEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.4.1

Indicates the performance stat of the Low order Path.

Indexes

hwSDHLpPerfCurrentIfIndex hwSDHLpPerfCurrentHpIndex hwSDHLpPerfCurrentLpIndex hwSDHLpPerfCurrentDataIndex

Column	Syntax	OID
hwSDHLpPerfCurrentIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.1
hwSDHLpPerfCurrentHpIndex This object indicates the HP index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.2
hwSDHLpPerfCurrentLpIndex This object indicates the lower order path (LP) index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.3
hwSDHLpPerfCurrentDataIndex This object indicates the data index.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.4
hwSDHLpPerfCurrentBBE This object indicates the background errored block of the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.5
hwSDHLpPerfCurrentES This object indicates the number of errored seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.6
hwSDHLpPerfCurrentSES This object indicates the number of severe errored seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.7
hwSDHLpPerfCurrentUAS This object indicates the number of unavailable seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.8
hwSDHLpPerfCurrentFEBBE This object indicates the the remote background errored block of the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.9
hwSDHLpPerfCurrentFEES This object indicates the number of remote errored seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.10
hwSDHLpPerfCurrentFESES This object indicates the number of remote errored seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.11
hwSDHLpPerfCurrentFEUAS This object indicates the number of unavailable seconds on the lower order path (LP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.4.1.12

This table describes functions of physical interfaces.

hwPDHPerfCurrentEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.5.1

Indicates the performance stat of the E1 line side.

Indexes

hwPDHPerfCurrentIfIndex hwPDHPerfCurrentDataIndex

Column	Syntax	OID
hwPDHPerfCurrentIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.1
hwPDHPerfCurrentDataIndex This object indicates the data index.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.2
hwPDHPerfCurrentBBE This object indicates the background errored block of the higher order path (HP).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.3
hwPDHPerfCurrentES This object indicates the number of errored seconds on the E1 line code.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.4
hwPDHPerfCurrentSES This object indicates the number of severe errored seconds on the E1 line code.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.5
hwPDHPerfCurrentUAS This object indicates the number of seconds for the loss of signals on the E1 line code.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.6
hwPDHPerfCurrentLCV This object indicates the number of errors on the E1 line code.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.8.5.1.7

This table describes the output of error packets and packet length configuration.

hwEthPortStatEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.6.1

Indicates the stat of the ethernet interface.

Indexes

hwEthPortStatIfIndex

Column	Syntax	OID
hwEthPortStatIfIndex This object indicates the interface index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.1
hwEthPortStatBadBytes This object indicates the statistics about the Badtypes errors.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.2
hwEthPortStatOutPut64Bytes This object indicates the number of output data packets each with a length less than or equal to 64 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.3
hwEthPortStatOutPut65to127Bytes This object indicates the number of output data packets each with a length ranging from 65 bytes to 127 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.4
hwEthPortStatOutPut128to255Bytes This object indicates the number of output data packets each with a length ranging from 128 bytes to 255 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.5
hwEthPortStatOutPut256to511Bytes This object indicates the number of output data packets each with a length ranging from 256 bytes to 511 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.6
hwEthPortStatOutPut512to1023Bytes This object indicates the number of output data packets each with a length ranging from 512 bytes to 1023 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.7
hwEthPortStatOutPut1024to1518Bytes This object indicates the number of output data packets each with a length ranging from 1024 bytes to 1518 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.8
hwEthPortStatOutPut1519toMaxBytes This object indicates the number of sent data packets each with a length greater than or equal to 1519 bytes.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.2011.5.25.157.1.8.6.1.9

Set the physical port close enable(1) disable(2) by EthOam.

hwEthOamPortLinkEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.8.1

Set the physical port close enable(1) disable(2) by EthOam.

Indexes

hwPhysicalPortIfIndex

Column	Syntax	OID
hwMepId the ID of the MEP.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.25.157.1.8.8.1.1
hwUniName the name of Uni interface that configed EthOam.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.8.1.2

Get management port status.

hwMEthStatusEntry row .1.3.6.1.4.1.2011.5.25.157.1.8.9.1

Get management port status.

Indexes

hwMethIfIndex

Column	Syntax	OID
hwMethIfIndex Interface index(es) of physical port(s) present on the device.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.5.25.157.1.8.9.1.1
hwMEthPortName The name of management port.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.8.9.1.2
hwMEthPhyStatus The status of management port is 1(up) or 0(down).	Enumeration Enumerated Values: 0 down 1 up	.1.3.6.1.4.1.2011.5.25.157.1.8.9.1.3
hwMEthIsActive The status of management port is 1(active) or 0(inactive).	Enumeration Enumerated Values: 0 inactive 1 active	.1.3.6.1.4.1.2011.5.25.157.1.8.9.1.4

Indicates the attributes of the dsl group.

hwDslGroupEntry row .1.3.6.1.4.1.2011.5.25.157.1.9.1.1

An entry in the dsl group table.

Indexes

hwDslGroupIfIndex

Column	Syntax	OID
hwDslGroupIfIndex Interface index(es) of dsl group present on the device.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.1
hwDslGroupWorkMode The dsl group of SHD4 card can work in efm or atm mode. Default is efm.	Enumerationr/w Enumerated Values: 1 atm 2 efm	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.2
hwDslGroupBisState Bis can be enabled or disabled in ATM mode of SHD4 card.	Enumerationr/w Enumerated Values: 1 disable 2 enable 3 notSupport	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.3
hwDslGroupEncapeMode The dsl group of AVD8 card can work in ETHoA-LLC mode or ETHoA-VCMUX mode. Default is ETHoA-LLC.	Enumerationr/w Enumerated Values: 1 eoaLlc 2 eoaVcmux 3 notSupport	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.4
hwDslGroupEnable Trigger the operation of binding dsl link(s) to the dsl group.	Enumerationr/w Enumerated Values: 1 disable 2 enable 3 notSupport	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.5
hwDslGroupRowStatus An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be reject…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.9.1.1.60

Indicates the attributes of the dsl group bound virtual-ethernet.

hwDslGroupBoundVeEntry row .1.3.6.1.4.1.2011.5.25.157.1.9.2.1

An entry in the dsl group bound vitrual-ethernet table.

Indexes

hwDslGroupIfIndexOfBound hwDslGroupPvcId

Column	Syntax	OID
hwDslGroupIfIndexOfBound Interface index(es) of dsl group present on the device.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.1
hwVirtualEthernetIfIndex The first virtual ethernet interface which the dsl group is bound to.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.2
hwDslGroupVpi VPI value of the 1st PVC pair.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.3
hwDslGroupVci VCI value of the 1st PVC pair.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.4
hwDslGroupPvcId Identifier for VPI/VCI Pair.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.5
hwBoundVeRowStatusobsolete An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be reject…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.9.2.1.50

Indicates the relation of the dsl group binding virtual-ethernet.

hwDslGroupBindVeEntry row .1.3.6.1.4.1.2011.5.25.157.1.9.3.1

An entry in the dsl group binding vitrual-ethernet table.

Indexes

hwDslGroupInterfaceIndex hwVirtualEthernetInterfaceIndex

Column	Syntax	OID
hwDslGroupInterfaceIndex Interface index(es) of the dsl group present on the device.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.9.3.1.1
hwVirtualEthernetInterfaceIndex The virtual ethernet interface index which the dsl group is bound to.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.9.3.1.2
hwBindVeRowStatus An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be reject…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.9.3.1.50

Indicates the attributes of the dsl ima group.

hwDslGroupImaEntry row .1.3.6.1.4.1.2011.5.25.157.1.10.1.1

An entry of the dsl ima group table.

Indexes

hwDslGroupImaIfIndex

Column	Syntax	OID
hwDslGroupImaIfIndex Interface index(es) of dsl group present on the device.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.1
hwDslGroupImaVersion Version of the ima group of SHD4I card. v0: ima protocol version 1.0; v1: ima protocol version 1.1.	Enumerationr/w Enumerated Values: 1 v0 2 v1	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.2
hwDslGroupImaFrameLen Frame length of the ima group of SHD4I card. If ima protocol version is 1.0, the frame length is only 128.	HUAWEI-IMA-MIBImaFrameLengthr/w Type Values: 1 m32 2 m64 3 m128 4 m256	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.3
hwDslGroupImaReset ima group reset for SHD4I card.	Enumerationr/w Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.4
hwDslGroupImaTxMinLinkNum Minimum active links number by TX direction.	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.5
hwDslGroupImaRxMinLinkNum Minimum active links number by RX direction.	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.6
hwDslGroupImaNeState The current state of the near-end ima group.	HUAWEI-IMA-MIBImaGroupState Type Values: 1 notConfigured 2 startUp 3 startUpAck 4 configAbortUnsupportedM 5 configAbortIncompatibleSymmetry 6 configAbortOther 7 insufficientLinks 8 blocked 9 operational 10 configAbortUnsupportedImaVersion	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.7
hwDslGroupImaFeState The current state of the far-end ima group.	HUAWEI-IMA-MIBImaGroupState Type Values: 1 notConfigured 2 startUp 3 startUpAck 4 configAbortUnsupportedM 5 configAbortIncompatibleSymmetry 6 configAbortOther 7 insufficientLinks 8 blocked 9 operational 10 configAbortUnsupportedImaVersion	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.8
hwDslGroupImaTxCellRate The current cell rate of ima group by TX direction.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.9
hwDslGroupImaRxCellRate The current cell rate of ima group by RX direction.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.10
hwDslGroupImaTxActLinkNum Number of active links by TX direction.	Integer32 Constraints: range: 0-4	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.11
hwDslGroupImaRxActLinkNum Number of active links by RX direction.	Integer32 Constraints: range: 0-4	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.12
hwDslGroupImaIfName The interface name of ima group.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.10.1.1.13

Indicates the dsl link bound relation.

hwDslLinkEntry row .1.3.6.1.4.1.2011.5.25.157.1.11.1.1

An entry of the dsl link bound relation.

Indexes

hwBoundDslGroupIfIndex hwDslLinkIfIndex

Column	Syntax	OID
hwBoundDslGroupIfIndex Interface index of dsl group which the dsl link bound to.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.11.1.1.1
hwDslLinkIfIndex Interface index of the dsl link device.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.11.1.1.2
hwDslLinkIfName The interface name of the dsl link.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.11.1.1.4
hwBoundDslGroupIfName Interface index of dsl group which the dsl link bound to.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.11.1.1.5
hwDslLinkBoundRowStatus An object that allows entries in this table to be created, modified and deleted using the RowStatus convention. A SET operation to any other attribute in this row, when this object is set to 'active' (1), MUST be reject…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.5.25.157.1.11.1.1.50

Indicates the attributes of the PW alarm.

hwPWAlarmEntry row .1.3.6.1.4.1.2011.5.25.157.1.12.1.1

An entry of the PW alarm relation.

Indexes

hwPWAlarmIfIndex

Column	Syntax	OID
hwPWAlarmIfIndex Interface index of PW alarm group.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.1
hwPWCesVcID Vc ID of PW alarm group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.2
hwPWCesVcType Vc Type of PW alarm group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.3
hwPeerIpAddr Peer IP Address of PW alarm group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.4
hwAlarmStatusobsolete Alarm status of PW alarm group.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.5
hwPWAlarmRMLEnableStatus PW control word RML of PW alarm group.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.6
hwLosAlarmTriggerThreshold Trigger Threshold of continuous loss packets of PW alarm group.	Integer32r/w Constraints: range: 2-65535	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.7
hwLosAlarmResumeThreshold Resume Threshold of continuous loss packets of PW alarm group.	Integer32r/w Constraints: range: 32-65535	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.8
hwPWPortName PW port name of PW alarm group.	OctetString	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.9
hwLosPktExcTriggerThreshold Trigger threshold of lost packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.10
hwLosPktExcResumeThreshold Resume threshold of lost packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.11
hwMisorderPktExcTriggerThreshold Trigger threshold of packets lost due to the out-of-order condition of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.12
hwMisorderPktExcResumeThreshold Resume threshold of packets lost due to the out-of-order condition of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.13
hwStrayPktExcTriggerThreshold Trigger threshold of misconnected packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.14
hwStrayPktExcResumeThreshold Resume threshold of misconnected packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.15
hwMalPktExcTriggerThreshold Trigger threshold of malformed packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.16
hwMalPktExcResumeThreshold Resume threshold of malformed packets of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.17
hwJtrUdrExcTriggerThreshold Trigger threshold of jitter buffer underflows of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.18
hwJtrUdrExcResumeThreshold Resume threshold of jitter buffer underflows of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.19
hwJtrOvrExcTriggerThreshold Trigger threshold of jitter buffer overflows of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.20
hwJtrOvrExcResumeThreshold Resume threshold of jitter buffer overflows of PW alarm group.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.5.25.157.1.12.1.1.21