HUAWEI-NTP-TRAP-MIB

This MIB is to provide TRAP support for NTP.
hwNtpStateChangeTrap & hwNtpSysPeerChangeTrap are added to notify the 
NTP state change & system peer change information
    

Imported Objects

huaweiUtilityHUAWEI-MIB
InterfaceIndexIF-MIB
InetAddress, InetAddressTypeINET-ADDRESS-MIB
NOTIFICATION-GROUP, MODULE-COMPLIANCE, OBJECT-GROUPSNMPv2-CONF
MODULE-IDENTITY, Counter64, Integer32, Unsigned32, IpAddress, NOTIFICATION-TYPE, OBJECT-TYPESNMPv2-SMI
TruthValue, DateAndTime, DisplayString, RowStatusSNMPv2-TC

Objects

hwNtpTrapMib .1.3.6.1.4.1.2011.6.80
hwNtpTrapObjects .1.3.6.1.4.1.2011.6.80.1
hwNtpState .1.3.6.1.4.1.2011.6.80.1.1
hwNtpSource
.1.3.6.1.4.1.2011.6.80.1.2
hwNtpSourceVpnName .1.3.6.1.4.1.2011.6.80.1.3
hwNtpOldSource
.1.3.6.1.4.1.2011.6.80.1.4
hwNtpOldSourceVpnName .1.3.6.1.4.1.2011.6.80.1.5
hwNtpCurrentClientNum .1.3.6.1.4.1.2011.6.80.1.6
hwNtpMaxDynamicSessions .1.3.6.1.4.1.2011.6.80.1.7
hwNtpMaxPacketRecvPerSecr .1.3.6.1.4.1.2011.6.80.1.8
hwNtpTraps .1.3.6.1.4.1.2011.6.80.2
hwNtpTrapMibConformance .1.3.6.1.4.1.2011.6.80.3
hwNtpTrapMibCompliances .1.3.6.1.4.1.2011.6.80.3.1

Notifications/Traps

NameOIDDescription
hwNtpStateChangeTrap



.1.3.6.1.4.1.2011.6.80.2.1
is used to notify when the NTP state changes from synchronized to unsynchronized & vice-versa.
NTP state changes occur due to reasons listed below
	1) System clock is reset by configuration.
	2) Selected peer is deleted by configuration.
	3) Selected peer is unreachable.
	4) Authentication failed for selected peer.
	5) Selected peer clock is not synchronized.
	6) Time elapsed since peer clock's last update is not within permissible limit.
	7) Source stratum is greater than the local stratum.
	8) System synchronization source lost.
	9) NTP mode mismatch for selected peer.
hwNtpSynchronizationFailureResume


.1.3.6.1.4.1.2011.6.80.2.10
This NTP state unsynchronized alarm was repaired.
hwNtpSysPeerChangeTrap




.1.3.6.1.4.1.2011.6.80.2.2
is used to notify the NTP system peer change from one source IP to other source IP without state change.
This trap is generated when the selected NTP peer is changed
hwNtpClientLimitExceed

.1.3.6.1.4.1.2011.6.80.2.3
This TRAP is used to notify the NTP client path limit exceed.
hwNtpClientLimitExceedResume

.1.3.6.1.4.1.2011.6.80.2.4
This NTP client path limit exceed alarm was repaired.
hwNtpDynamicSessionLimitReach

.1.3.6.1.4.1.2011.6.80.2.5
This TRAP is used to notify the NTP dynamic session limit reach.
hwNtpDynamicSessionLimitReachResume

.1.3.6.1.4.1.2011.6.80.2.6
This NTP dynamic session limit reach alarm was repaired.
hwNtpMaxPacketRecvPerSecReach

.1.3.6.1.4.1.2011.6.80.2.7
This TRAP is used to notify the NTP packet processing rate reaches the upper threshold.
hwNtpMaxPacketRecvPerSecResume

.1.3.6.1.4.1.2011.6.80.2.8
This NTP packet processing rate reaches the upper threshold alarm was repaired.
hwNtpSynchronizationFailure


.1.3.6.1.4.1.2011.6.80.2.9
This TRAP is used to notify when the NTP state changes from synchronized to unsynchronized.