HUAWEI-DC-TRAP-MIB

        The HUAWEI-DC-TRAP-MIB provides information about DataComm TRAPS.
hwDCTrapMIB1.3.6.1.4.1.2011.5.25.37

Imported Objects

entPhysicalNameENTITY-MIB
hwDatacommHUAWEI-MIB
ifIndex, ifDescrRFC1213-MIB
OBJECT-GROUP, MODULE-COMPLIANCE, NOTIFICATION-GROUPSNMPv2-CONF
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32SNMPv2-SMI
DisplayStringSNMPv2-TC

Objects

hwDCTrapMIB .1.3.6.1.4.1.2011.5.25.37
hwDCTrapControl .1.3.6.1.4.1.2011.5.25.37.1
hwDCCtrlTrap .1.3.6.1.4.1.2011.5.25.37.1.1
hwTunnelGroupID .1.3.6.1.4.1.2011.5.25.37.1.2
hwDCTrapReason
.1.3.6.1.4.1.2011.5.25.37.1.3
hwDCTraps .1.3.6.1.4.1.2011.5.25.37.2
hwDCTrapConformance .1.3.6.1.4.1.2011.5.25.37.3
hwDCTrapGroups .1.3.6.1.4.1.2011.5.25.37.3.1
hwDCTrapCompliances .1.3.6.1.4.1.2011.5.25.37.3.2

Notifications/Traps

NameOIDDescription
hwMPUSynClkFaulty.1.3.6.1.4.1.2011.5.25.37.2.1
MPU sync clock signal faulty!
hwBrdAutoSwtFail.1.3.6.1.4.1.2011.5.25.37.2.10
Board automatically switch syn-clock but it locked failed!
hwWriteFlashError.1.3.6.1.4.1.2011.5.25.37.2.100
write flash error!
hwBoardReset.1.3.6.1.4.1.2011.5.25.37.2.101
board reset!
hwBoardResetSuccess.1.3.6.1.4.1.2011.5.25.37.2.102
board reset success!
hwSlaveMPUReset.1.3.6.1.4.1.2011.5.25.37.2.103
slave MPU reset !
hwMasterSlaveSwap.1.3.6.1.4.1.2011.5.25.37.2.104
master slave swap!
hwRTCFail.1.3.6.1.4.1.2011.5.25.37.2.105
RTC failure!
hwExchangeChipFail.1.3.6.1.4.1.2011.5.25.37.2.106
5695 exchange chip fail!
hwTempResume.1.3.6.1.4.1.2011.5.25.37.2.107
Board temprature over threshold resume!
hwOpticalModuleInsert.1.3.6.1.4.1.2011.5.25.37.2.108
optical module plug in !
hwOpticalModuleRemove.1.3.6.1.4.1.2011.5.25.37.2.109
optical module plug out !
hwBrdAutoSwt.1.3.6.1.4.1.2011.5.25.37.2.11
Board automatically switch syn-clock!
hwFPGAAbnormal.1.3.6.1.4.1.2011.5.25.37.2.110
FPGA abnormal !
hwMinMTunnelDownAlarm.1.3.6.1.4.1.2011.5.25.37.2.111
For Mac in Mac tunnel. Mac tunnel have two status: up or down, when physical interface is down or some cc package 
can't arrive to the other side of mac in mac tunnel, the status of tunnel will be down
1 Notice/Trap name: Tunnel down
2 Notice/Trap generation cause: when All mac tunnel have been down in the mac tunnel group
3 Repair suggestions:
    make one of the mac tunnel up in the mac tunnel group
hwMinMTunnelUpAlarm.1.3.6.1.4.1.2011.5.25.37.2.112
For Mac in Mac tunnel. Mac tunnel have two status: up or down, if cc package can arrive to the other side of mac
in mac tunnel, the status of tunnel will be up
1 Notice/Trap name: Tunnel up
2 Notice/Trap generation cause: one of the tunnel is up in the mac tunnel group
3 Repair suggestion:
hwInterfacePhysicalDown.1.3.6.1.4.1.2011.5.25.37.2.113
This trap is to indicate port link down on physical layer.
hwInterfacePhysicalUp.1.3.6.1.4.1.2011.5.25.37.2.114
This trap is to indicate port link up on physical layer.
hwBTBStartupFileNameDifferent.1.3.6.1.4.1.2011.5.25.37.2.119
In the BTB system ,the start-up file name of master and slave chassis is different .
Used for BTB or its extend system.
hwBrdClkLockERR.1.3.6.1.4.1.2011.5.25.37.2.12
Board fabric clock is unlocked!
hwBTBChassisRunningModeConflict.1.3.6.1.4.1.2011.5.25.37.2.120
The Master and Slave chassises running modes conflict.Used for BTB or its extend system.
hwBTBCtrlChannelFail.1.3.6.1.4.1.2011.5.25.37.2.121
The FE control channel failture, as physical link from up to down or channel blocked.
Used for BTB or its extend system.
hwBTBCtrlChannelFailResume.1.3.6.1.4.1.2011.5.25.37.2.122
The FE control channel failture resume.Used for BTB or its extend system.
hwBTBDataChannelFail.1.3.6.1.4.1.2011.5.25.37.2.123
The data channel failture, all optical links down between chassises.Used for BTB or its extend system.
hwBTBDataChannelFailResume.1.3.6.1.4.1.2011.5.25.37.2.124
The data channel failture resume.Used for BTB or its extend system.
hwBTBClkChannelFail.1.3.6.1.4.1.2011.5.25.37.2.125
The clock channel failture, clock link down between chassises.Used for BTB or its extend system.
hwBTBClkChannelFailResume.1.3.6.1.4.1.2011.5.25.37.2.126
The clock Channel failture resume.Used for BTB or its extend system.
hwBTBSFUOpticInterfaceError.1.3.6.1.4.1.2011.5.25.37.2.127
The optical fiber connection error, the connection of SFU fiber between chassises is not correct.
Used for BTB or its extend system.
hwBTBSFUOpticInterfaceErrorResume.1.3.6.1.4.1.2011.5.25.37.2.128
The optical fiber connection error resume.Used for BTB or its extend system.
hwBTBVSRInterfaceInvalid.1.3.6.1.4.1.2011.5.25.37.2.129
The SFU VSR(very short reach) interface invalid.Used for BTB or its extend system.
hwBrdClkLockERRResume.1.3.6.1.4.1.2011.5.25.37.2.13
Board fabric clock unlock to current clock resume!
hwBTBVSRInterfaceInvalidResume.1.3.6.1.4.1.2011.5.25.37.2.130
The SFU VSR(very short reach) interface invalid resume.Used for BTB or its extend system.
hwBTBSlaveChassisNoHeart.1.3.6.1.4.1.2011.5.25.37.2.131
The slave chassis no heart.Used for BTB or its extend system.
hwBTBNoSlaveChassis.1.3.6.1.4.1.2011.5.25.37.2.132
No slave chassis connected to the master chassis in the BTB system.Used for BTB or its extend system.
hwBTBSlaveChassisRegisted.1.3.6.1.4.1.2011.5.25.37.2.133
The slave chassis registe successful.Used for BTB or its extend system.
hwBTBSlaveChassisRegisteFail.1.3.6.1.4.1.2011.5.25.37.2.134
The slave chassis registe failed.Used for BTB or its extend system.
hwBTBChassisTypeConflict.1.3.6.1.4.1.2011.5.25.37.2.135
The chassis information conflict in the PAF and Nvram.Used for BTB or its extend system.
hwSuperChangeSuccesful.1.3.6.1.4.1.2011.5.25.37.2.136
Super change successful.
hwSuperChangeFailure.1.3.6.1.4.1.2011.5.25.37.2.137
Super change Failure.
hwOpticaPowerAbnormal.1.3.6.1.4.1.2011.5.25.37.2.138
Optical Transceiver power abnormal.
hwEpldAbnormal.1.3.6.1.4.1.2011.5.25.37.2.139
Epld logic abnormal.
hwBrdRemoved.1.3.6.1.4.1.2011.5.25.37.2.14
Board pulled out!
hwPhyChipAbnormal.1.3.6.1.4.1.2011.5.25.37.2.140
PHY chip is abnormal.
hwSerdesAbnormal.1.3.6.1.4.1.2011.5.25.37.2.141
Serdes interface of PHY chip abnormal.
hwBoardAbnormal.1.3.6.1.4.1.2011.5.25.37.2.142
Board is abnormal.
hwFeChannelAbnormal.1.3.6.1.4.1.2011.5.25.37.2.143
FE data channel is abnormal
hwParityCheckAbnormal.1.3.6.1.4.1.2011.5.25.37.2.144
Data parity check is abnormal
hwPhyClockAbnormal.1.3.6.1.4.1.2011.5.25.37.2.145
The clock of PHY chip is abnormal.
hwPortAutoNegotiateFail.1.3.6.1.4.1.2011.5.25.37.2.146
The ethernet port negotiate failed
hwPortSemiduplex.1.3.6.1.4.1.2011.5.25.37.2.147
The ethernet port work at semi duplex state.
hwScuStartModeSetFail.1.3.6.1.4.1.2011.5.25.37.2.148
The start mode of SCU set failed
hwMemoryExhaust.1.3.6.1.4.1.2011.5.25.37.2.149
MPU memory exhaust.
hwBrdInserted.1.3.6.1.4.1.2011.5.25.37.2.15
Board plugged in!
hwMemoryExhaustClear.1.3.6.1.4.1.2011.5.25.37.2.150
MPU memory usage resume to normal.
hwMethAbnormal.1.3.6.1.4.1.2011.5.25.37.2.151
The Meth interface is abnormal.
hwLpuNotTight.1.3.6.1.4.1.2011.5.25.37.2.152
The LPU board is not tightly installed. Install the board again.
hwLicenseFail.1.3.6.1.4.1.2011.5.25.37.2.153
License fail.
hwHaBatchBegin.1.3.6.1.4.1.2011.5.25.37.2.154
No command line can be entered because batch backup is processing.
hwHaBatchEnd.1.3.6.1.4.1.2011.5.25.37.2.155
Command lines can be entered because batch backup ends.
hwHaSmoothBegin.1.3.6.1.4.1.2011.5.25.37.2.156
No command line can be entered because data smooth is processing.
hwHaSmoothEnd.1.3.6.1.4.1.2011.5.25.37.2.157
Command lines can be entered because data smooth ends.
hwFanUp.1.3.6.1.4.1.2011.5.25.37.2.158
Fan register!
hwBrdUp.1.3.6.1.4.1.2011.5.25.37.2.16
Board register!
hwClkSrcMiss.1.3.6.1.4.1.2011.5.25.37.2.17
CLK source Loss Of Signal!
hwClkAllSrcLost.1.3.6.1.4.1.2011.5.25.37.2.18
CLK all source lost!
hwClkAllSrcLostResume.1.3.6.1.4.1.2011.5.25.37.2.19
CLK all source lost resume!
hwMPUSynClkFaultyResume.1.3.6.1.4.1.2011.5.25.37.2.2
MPU sync clock signal faulty resume!
hwClkFail.1.3.6.1.4.1.2011.5.25.37.2.20
CLK hardware failed!
hwClkFailResume.1.3.6.1.4.1.2011.5.25.37.2.21
CLK hardware failed resume!
hwClkNoHeartbeat.1.3.6.1.4.1.2011.5.25.37.2.22
CLK No Heartbeat!
hwClkNoHeartbeatResume.1.3.6.1.4.1.2011.5.25.37.2.23
CLK No Heartbeat resume!
hwLPULostSynAlarm.1.3.6.1.4.1.2011.5.25.37.2.24
LPU SERDES interface is lost synchronization!
hwLPUOpenChannelError.1.3.6.1.4.1.2011.5.25.37.2.25
LPU SERDES interface open error!
hwLPUSlfTstErr.1.3.6.1.4.1.2011.5.25.37.2.26
LPU self test error!
hwLPU3ClkSwitch.1.3.6.1.4.1.2011.5.25.37.2.27
LPU 3 class clock is switch!
hwSFULostHrtReset.1.3.6.1.4.1.2011.5.25.37.2.28
SFU is reset because of heart beat loss!
hwSFULinkLostReset.1.3.6.1.4.1.2011.5.25.37.2.29
SFU is reset because of SERDES interface input channel link lost numbers over threshold!
hwSlaveMPUNoResp.1.3.6.1.4.1.2011.5.25.37.2.3
Slave MPU has no response!
hwSFUChannelLinkLost.1.3.6.1.4.1.2011.5.25.37.2.30
SFU check SERDES interface input channel link lost!
hwSFUInChannelOpenFail.1.3.6.1.4.1.2011.5.25.37.2.31
SFU SERDES interface input channel is opened failed!
hwVoltSensorFail.1.3.6.1.4.1.2011.5.25.37.2.32
Board voltage monitor failure!
hwVoltSensorFailResume.1.3.6.1.4.1.2011.5.25.37.2.33
Board voltage monitor failure resume!
hwVoltBtmC.1.3.6.1.4.1.2011.5.25.37.2.34
Board voltage below fatal threshold!
hwVoltBtmCResume.1.3.6.1.4.1.2011.5.25.37.2.35
Board voltage below fatal threshold resume!
hwVoltSprC.1.3.6.1.4.1.2011.5.25.37.2.36
Board voltage over fatal threshold!
hwVoltSprCResume.1.3.6.1.4.1.2011.5.25.37.2.37
Board voltage over fatal threshold resume!
hwVoltBtmM.1.3.6.1.4.1.2011.5.25.37.2.38
Board voltage below major threshold!
hwVoltBtmMResume.1.3.6.1.4.1.2011.5.25.37.2.39
Board voltage below major threshold resume!
hwSlaveMPUNoRespResume.1.3.6.1.4.1.2011.5.25.37.2.4
Slave MPU has no response resume!
hwVoltSprM.1.3.6.1.4.1.2011.5.25.37.2.40
Board voltage over major threshold!
hwVoltSprMResume.1.3.6.1.4.1.2011.5.25.37.2.41
Board voltage over major threshold resume!
hwTempSensorFail.1.3.6.1.4.1.2011.5.25.37.2.42
Board temprature monitor failure!
hwTempSensorFailResume.1.3.6.1.4.1.2011.5.25.37.2.43
Board temperature monitor failure resume!
hwTempMnr.1.3.6.1.4.1.2011.5.25.37.2.44
Board temperature over minor threshold!
hwTempMnrResume.1.3.6.1.4.1.2011.5.25.37.2.45
Board temperature over minor threshold resume!
hwTempMjr.1.3.6.1.4.1.2011.5.25.37.2.46
Board temperature over major threshold!
hwTempMjrResume.1.3.6.1.4.1.2011.5.25.37.2.47
Board temperature over major threshold resume!
hwTempCtl.1.3.6.1.4.1.2011.5.25.37.2.48
Board temperature over fatal threshold!
hwTempCtlResume.1.3.6.1.4.1.2011.5.25.37.2.49
Board temperature over fatal threshold resume!
hwBrdChannelFaulty.1.3.6.1.4.1.2011.5.25.37.2.5
Board channel faulty!
hwFanHFail.1.3.6.1.4.1.2011.5.25.37.2.50
Fan hardware failure!
hwDCFanFail.1.3.6.1.4.1.2011.5.25.37.2.51
Fan failure!
hwDCFanFailResume.1.3.6.1.4.1.2011.5.25.37.2.52
Fan failure resume!
hwFanAbsent.1.3.6.1.4.1.2011.5.25.37.2.53
Fan absent!
hwFanAbsentResume.1.3.6.1.4.1.2011.5.25.37.2.54
Fan absent resume!
hwFanCabUN.1.3.6.1.4.1.2011.5.25.37.2.55
Fan cable unplugged!
hwFanCabUNResume.1.3.6.1.4.1.2011.5.25.37.2.56
Fan cable unplugged resume!
hwPwrFail.1.3.6.1.4.1.2011.5.25.37.2.57
Power failure!
hwPwrFailResume.1.3.6.1.4.1.2011.5.25.37.2.58
Power failure resume!
hwPwrAbsent.1.3.6.1.4.1.2011.5.25.37.2.59
Power absent!
hwBrdChannelFaultyResume.1.3.6.1.4.1.2011.5.25.37.2.6
Board channel faulty resume!
hwPwrAbsentResume.1.3.6.1.4.1.2011.5.25.37.2.60
Power absent resume!
hwPwrCabUN.1.3.6.1.4.1.2011.5.25.37.2.61
Power monitor cable unplugged!
hwPwrCabUNResume.1.3.6.1.4.1.2011.5.25.37.2.62
Power monitor cable unplugged resume!
hwLCDHFail.1.3.6.1.4.1.2011.5.25.37.2.63
LCD hardware failure!
hwLCDFail.1.3.6.1.4.1.2011.5.25.37.2.64
LCD failure!
hwLCDAbsent.1.3.6.1.4.1.2011.5.25.37.2.65
LCD absent!
hwLCDAbsentResume.1.3.6.1.4.1.2011.5.25.37.2.66
LCD absent resume!
hwLCDCabUN.1.3.6.1.4.1.2011.5.25.37.2.67
LCD cable unplugged!
hwLCDCabUNResume.1.3.6.1.4.1.2011.5.25.37.2.68
LCD cable unplugged resume!
hwROMFail.1.3.6.1.4.1.2011.5.25.37.2.69
EEPROM failure!
hwBrdNofullin.1.3.6.1.4.1.2011.5.25.37.2.7
Board not full in!
hwMonitorBUSFail.1.3.6.1.4.1.2011.5.25.37.2.70
MonitorBUS failure!
hwMonitorBUSFailResume.1.3.6.1.4.1.2011.5.25.37.2.71
MonitorBUS failure resume!
hwBoardOfflineChange.1.3.6.1.4.1.2011.5.25.37.2.72
Board power status change!
hwBrdNofullinResume.1.3.6.1.4.1.2011.5.25.37.2.8
Board not full in resume!
hwBrdTypeNoMatchReset.1.3.6.1.4.1.2011.5.25.37.2.9
Board is reset because of the chip type is not matching!