 hPFWUpdate1 | .1.3.6.1.4.1.11.2.23.0.101 | Front Panel Controller firmware updated |
| hPFWUpdate2 | .1.3.6.1.4.1.11.2.23.0.102 | Primary Hot Swap Cage Controller firmware updated |
| hPFWUpdate3 | .1.3.6.1.4.1.11.2.23.0.103 | Secondary Hot Swap Cage Controller firmware updated |
| hPFWUpdate4 | .1.3.6.1.4.1.11.2.23.0.104 | NetServer Management Controller firmware updated |
| hPFWUpdate5 | .1.3.6.1.4.1.11.2.23.0.105 | CPU Management Controller firmware updated |
| networkCard2 | .1.3.6.1.4.1.11.2.23.0.116385 | The total number of packets with receive errors has exceeded the threshold. |
| networkCard6 | .1.3.6.1.4.1.11.2.23.0.116386 | The total number of packets with transmit errors has exceeded the threshold. |
| networkCard10 | .1.3.6.1.4.1.11.2.23.0.116387 | The total number of LAN Adapter reset errors has exceeded the threshold. |
| networkCard14 | .1.3.6.1.4.1.11.2.23.0.116388 | The total number of alignment and CRC errors has exceeded the threshold. |
| networkCard18 | .1.3.6.1.4.1.11.2.23.0.116389 | The total number of giant frame packets has exceeded the threshold. |
| networkCard22 | .1.3.6.1.4.1.11.2.23.0.116390 | The total number of packets with length less than the required minimum length has exceeded the threshold. |
| networkCard26 | .1.3.6.1.4.1.11.2.23.0.116391 | The total number of late collision errors has exceeded the threshold (the network is too large). |
| networkCard30 | .1.3.6.1.4.1.11.2.23.0.116392 | The total number of colliding packets has exceeded the threshold (the network is too busy). |
| networkCard34 | .1.3.6.1.4.1.11.2.23.0.116393 | The total number of carrier sense errors has exceeded the threshold. |
| networkCard38 | .1.3.6.1.4.1.11.2.23.0.116394 | The total number of adapter deferrals has exceeded the threshold (the network is forever busy). |
| networkCard42 | .1.3.6.1.4.1.11.2.23.0.116395 | The total number of No ECB errors (LAN adapter is out of receive buffers) errors has exceeded the threshold. |
| networkCard46 | .1.3.6.1.4.1.11.2.23.0.116396 | The total number of Receive Overflow errors has exceeded the threshold. |
| networkCard50 | .1.3.6.1.4.1.11.2.23.0.116397 | LAN adapter utilization count has exceeded the threshold. |
| networkCard54 | .1.3.6.1.4.1.11.2.23.0.116398 | The LAN adapter which the alarms were configured for, has been replaced by another type of LAN adapter. |
| networkCard66 | .1.3.6.1.4.1.11.2.23.0.116418 | The active NIC in a redundant group has failed. The standby NIC has taken over. |
| networkCard68 | .1.3.6.1.4.1.11.2.23.0.116419 | A previously failed NIC in a redundant group has become operational. |
| networkCard70 | .1.3.6.1.4.1.11.2.23.0.116420 | The standby NIC in a redundant group has failed. |
| networkCard72 | .1.3.6.1.4.1.11.2.23.0.116421 | All NICs (active and standby) in a redundant group have failed. |
| temperature1 | .1.3.6.1.4.1.11.2.23.0.12288 | Server temperature monitor cannot read temperature data. |
| temperature2 | .1.3.6.1.4.1.11.2.23.0.12289 | Server temperature has exceeded the warning temperature threshold. |
| temperature3 | .1.3.6.1.4.1.11.2.23.0.12290 | Server temperature has exceeded the emergency temperature threshold. |
| networkCard1 | .1.3.6.1.4.1.11.2.23.0.16385 | The total number of packets with receive errors has exceeded the threshold. |
| networkCard5 | .1.3.6.1.4.1.11.2.23.0.16386 | The total number of packets with transmit errors has exceeded the threshold. |
| networkCard9 | .1.3.6.1.4.1.11.2.23.0.16387 | The total number of LAN Adapter reset errors has exceeded the threshold. |
| networkCard13 | .1.3.6.1.4.1.11.2.23.0.16388 | The total number of alignment and CRC errors has exceeded the threshold. |
| networkCard17 | .1.3.6.1.4.1.11.2.23.0.16389 | The total number of giant frame packets has exceeded the threshold. |
| networkCard21 | .1.3.6.1.4.1.11.2.23.0.16390 | The total number of packets with length less than the required minimum length has exceeded the threshold. |
| networkCard25 | .1.3.6.1.4.1.11.2.23.0.16391 | The total number of late collision errors has exceeded the threshold (the network is too large). |
| networkCard29 | .1.3.6.1.4.1.11.2.23.0.16392 | The total number of colliding packets has exceeded the threshold (the network is too busy). |
| networkCard33 | .1.3.6.1.4.1.11.2.23.0.16393 | The total number of carrier sense errors has exceeded the threshold. |
| networkCard37 | .1.3.6.1.4.1.11.2.23.0.16394 | The total number of adapter deferrals has exceeded the threshold (the network is forever busy). |
| networkCard41 | .1.3.6.1.4.1.11.2.23.0.16395 | The total number of No ECB errors (LAN adapter is out of receive buffers) errors has exceeded the threshold. |
| networkCard45 | .1.3.6.1.4.1.11.2.23.0.16396 | The total number of Receive Overflow errors has exceeded the threshold. |
| networkCard49 | .1.3.6.1.4.1.11.2.23.0.16397 | LAN adapter utilization count has exceeded the threshold. |
| networkCard53 | .1.3.6.1.4.1.11.2.23.0.16398 | The LAN adapter which the alarms were configured for, has been replaced by another type of LAN adapter. |
| networkCard55 | .1.3.6.1.4.1.11.2.23.0.16399 | There possibly is a dataflow problem with your HP LAN adapter. |
| networkCard56 | .1.3.6.1.4.1.11.2.23.0.16400 | The HP LAN adapter driver did not receive a transmit complete interrupt. |
| networkCard57 | .1.3.6.1.4.1.11.2.23.0.16401 | There possibly is a dataflow problem with your HP LAN adapter. |
| networkCard58 | .1.3.6.1.4.1.11.2.23.0.16402 | There is a dataflow problem with your HP LAN adapter - receive interrupts are being generated, but no receive packets are being present. |
| networkCard59 | .1.3.6.1.4.1.11.2.23.0.16403 | There possibly is a problem with your HP LAN adapter - it generates too many buffer pointer errors. |
| networkCard60 | .1.3.6.1.4.1.11.2.23.0.16404 | There possibly is a problem with your HP LAN adapter - DMA timed out while transmitting or receiving a packet. |
| networkCard61 | .1.3.6.1.4.1.11.2.23.0.16405 | The HP LAN adapter is transmitting faster than the media can handle. |
| networkCard62 | .1.3.6.1.4.1.11.2.23.0.16406 | The number of buffer fragments has exceeded the maximum number allowed by the network protocol in your HP LAN adapter. |
| networkCard63 | .1.3.6.1.4.1.11.2.23.0.16407 | The total number of errors due to requests of an ECB being denied has exceeded the threshold. |
| networkCard64 | .1.3.6.1.4.1.11.2.23.0.16408 | There possibly is a problem with your HP LAN adapter running in bus master mode. |
| networkCard65 | .1.3.6.1.4.1.11.2.23.0.16418 | The active NIC in a redundant group has failed. The standby NIC has taken over. |
| networkCard67 | .1.3.6.1.4.1.11.2.23.0.16419 | A previously failed NIC in a redundant group has become operational. |
| networkCard69 | .1.3.6.1.4.1.11.2.23.0.16420 | The standby NIC in a redundant group has failed. |
| networkCard71 | .1.3.6.1.4.1.11.2.23.0.16421 | All NICs (active and standby) in a redundant group have failed. |
| systemHW6 | .1.3.6.1.4.1.11.2.23.0.20528 | Parity error has been detected in parity memory |
| systemHW8 | .1.3.6.1.4.1.11.2.23.0.20544 | One of the bus masters caused a bus timeout |
| systemHW7 | .1.3.6.1.4.1.11.2.23.0.20545 | IPMB Protocol Error |
| systemHW73 | .1.3.6.1.4.1.11.2.23.0.20546 | NOS memory dump initiated |
| systemHW9 | .1.3.6.1.4.1.11.2.23.0.20560 | I/0 channel check activated by device in EISA slot caused an error |
| systemHW11 | .1.3.6.1.4.1.11.2.23.0.20576 | Software NMI has been generated |
| systemHW12 | .1.3.6.1.4.1.11.2.23.0.20577 | Uncorrectable Bus Error |
| systemHW64 | .1.3.6.1.4.1.11.2.23.0.20578 | Cache Protocol and Parity error |
| systemHW65 | .1.3.6.1.4.1.11.2.23.0.20579 | Correctable data error |
| systemHW13 | .1.3.6.1.4.1.11.2.23.0.20592 | Memory size has been adjusted during the Power-On-Self-Test during the last boot |
| systemHW14 | .1.3.6.1.4.1.11.2.23.0.20624 | Parity error has occurred on a transfer to/from a device on one of the PCI buses |
| systemHW16 | .1.3.6.1.4.1.11.2.23.0.20640 | System error has occurred in the PCI subsystem |
| systemHW21 | .1.3.6.1.4.1.11.2.23.0.20656 | Processor or Terminator (#) not detected |
| systemHW18 | .1.3.6.1.4.1.11.2.23.0.20657 | An uncorrectable Processor problem was detected. |
| systemHW19 | .1.3.6.1.4.1.11.2.23.0.20658 | Processor (#) Disabled |
| systemHW59 | .1.3.6.1.4.1.11.2.23.0.20659 | The CPU processor module is currently functioning properly, but it is no longer operating within acceptable margins |
| systemHW20 | .1.3.6.1.4.1.11.2.23.0.20660 | Processor or Terminator Card Not Detected |
| systemHW22 | .1.3.6.1.4.1.11.2.23.0.20661 | Processor Internal Error |
| systemHW23 | .1.3.6.1.4.1.11.2.23.0.20662 | Processor Thermal Trip Failure |
| systemHW24 | .1.3.6.1.4.1.11.2.23.0.20663 | Processor failed internal self test |
| systemHW25 | .1.3.6.1.4.1.11.2.23.0.20664 | Processor hung during POST |
| systemHW26 | .1.3.6.1.4.1.11.2.23.0.20665 | Processor startup/initialization failed |
| systemHW60 | .1.3.6.1.4.1.11.2.23.0.20666 | PCI Hot Plug fault deasserted |
| systemHW61 | .1.3.6.1.4.1.11.2.23.0.20667 | PCI Hot Plug Powered On |
| systemHW62 | .1.3.6.1.4.1.11.2.23.0.20668 | PCI Hot Plug fault asserted |
| systemHW63 | .1.3.6.1.4.1.11.2.23.0.20669 | PCI Hot Plug Powered off |
| systemHW27 | .1.3.6.1.4.1.11.2.23.0.20670 | Multiple Fan Failure |
| systemHW79 | .1.3.6.1.4.1.11.2.23.0.20671 | Configuration error in a processor slot |
| systemHW28 | .1.3.6.1.4.1.11.2.23.0.20672 | Timeout of failsafe timer has occurred |
| systemHW81s | .1.3.6.1.4.1.11.2.23.0.20673 | CPU thermal trip |
| systemHW82s | .1.3.6.1.4.1.11.2.23.0.20674 | CPU hot warning |
| systemHW80s | .1.3.6.1.4.1.11.2.23.0.20675 | CPU internal error |
| systemHW83 | .1.3.6.1.4.1.11.2.23.0.20676 | CPU mismatch |
| systemHW58 | .1.3.6.1.4.1.11.2.23.0.20680 | Front Panel Button Violation |
| systemHW29 | .1.3.6.1.4.1.11.2.23.0.20704 | Error logging for a specific error has been disabled due to too many errors of that kind in a short time period |
| systemHW43 | .1.3.6.1.4.1.11.2.23.0.20736 | An event of warning severity has occurred in the system. For example, chassis door has been opened |
| systemHW44 | .1.3.6.1.4.1.11.2.23.0.20737 | An event of critical severity has occurred in the system. For example, both system fans have failed |
| voltage2 | .1.3.6.1.4.1.11.2.23.0.20738 | Fatal voltage threshold on one of the system voltage sensors has been exceeded. Voltage sensors are +12V, +5V, -12V, +3.3V to PCI, +3.3V to Processor |
| voltage1 | .1.3.6.1.4.1.11.2.23.0.20739 | Warning voltage threshold on one of the system voltage channels has been exceeded. Voltage channels are +12V, +5V, -12V, +3.3V to PCI, +3.3V to Processor |
| systemHW10 | .1.3.6.1.4.1.11.2.23.0.20740 | Voltage utilization warning |
| systemHW11s | .1.3.6.1.4.1.11.2.23.0.20741 | Voltage utilization error |
| aSR1 | .1.3.6.1.4.1.11.2.23.0.20752 | Server has been restarted after the system watchdog timer has timed out due to NOS being hung |
| aSR2 | .1.3.6.1.4.1.11.2.23.0.20753 | OS Watchdog Shutdown |
| aSR3 | .1.3.6.1.4.1.11.2.23.0.20754 | OS Watchdog poweroff |
| systemFW3 | .1.3.6.1.4.1.11.2.23.0.20755 | OS Boot Complete |
| systemFW2 | .1.3.6.1.4.1.11.2.23.0.20756 | System Firmware Boot Start |
| systemFW4 | .1.3.6.1.4.1.11.2.23.0.20757 | Machine Check Initiated |
| systemFW1 | .1.3.6.1.4.1.11.2.23.0.20758 | Generic trap for Critical or Fatal type E0 event from system firmware |
| fibreChannel5 | .1.3.6.1.4.1.11.2.23.0.20759 | The Fibre Channel Adapter is Online |
| fibreChannel6 | .1.3.6.1.4.1.11.2.23.0.20760 | The Fibre Channel Adapter is Offline |
| systemHW30 | .1.3.6.1.4.1.11.2.23.0.20800 | EISA Configuration Utility has altered system configuration |
| systemHW48 | .1.3.6.1.4.1.11.2.23.0.20832 | The hardware eventlog has been cleared. |
| systemHW49 | .1.3.6.1.4.1.11.2.23.0.20833 | An unrecognized HW log event was detected. |
| systemHW50 | .1.3.6.1.4.1.11.2.23.0.20848 | The system has been rebooted. |
| redundantPower3 | .1.3.6.1.4.1.11.2.23.0.209103 | Indicates a failure with the AC power source that is connected to one of the redundant power supply units. |
| redundantPower6 | .1.3.6.1.4.1.11.2.23.0.209106 | Indicates that one of the redundant power supply modules is in over temperature protection mode. |
| redundantPower10 | .1.3.6.1.4.1.11.2.23.0.209109 | Indicates that one of the redundant power supply modules in the HP NetServer has recovered from an over temperature protection mode. |
| redundantPower12 | .1.3.6.1.4.1.11.2.23.0.209110 | Indicates that one of the redundant power supply modules in the HP NetServer has exceeded the warning temperature level. |
| networkCard3 | .1.3.6.1.4.1.11.2.23.0.216385 | The total number of packets with receive errors has exceeded the threshold. |
| networkCard7 | .1.3.6.1.4.1.11.2.23.0.216386 | The total number of packets with transmit errors has exceeded the threshold. |
| networkCard11 | .1.3.6.1.4.1.11.2.23.0.216387 | The total number of LAN Adapter reset errors has exceeded the threshold. |
| networkCard15 | .1.3.6.1.4.1.11.2.23.0.216388 | The total number of alignment and CRC errors has exceeded the threshold. |
| networkCard19 | .1.3.6.1.4.1.11.2.23.0.216389 | The total number of giant frame packets has exceeded the threshold. |
| networkCard23 | .1.3.6.1.4.1.11.2.23.0.216390 | The total number of packets with length less than the required minimum length has exceeded the threshold. |
| networkCard27 | .1.3.6.1.4.1.11.2.23.0.216391 | The total number of late collision errors has exceeded the threshold (the network is too large). |
| networkCard31 | .1.3.6.1.4.1.11.2.23.0.216392 | The total number of colliding packets has exceeded the threshold (the network is too busy). |
| networkCard35 | .1.3.6.1.4.1.11.2.23.0.216393 | The total number of carrier sense errors has exceeded the threshold. |
| networkCard39 | .1.3.6.1.4.1.11.2.23.0.216394 | The total number of adapter deferrals has exceeded the threshold (the network is forever busy). |
| networkCard43 | .1.3.6.1.4.1.11.2.23.0.216395 | The total number of No ECB errors (LAN adapter is out of receive buffers) errors has exceeded the threshold. |
| networkCard47 | .1.3.6.1.4.1.11.2.23.0.216396 | The total number of Receive Overflow errors has exceeded the threshold. |
| networkCard51 | .1.3.6.1.4.1.11.2.23.0.216397 | LAN adapter utilization count has exceeded the threshold. |
| systemHW10s | .1.3.6.1.4.1.11.2.23.0.220560 | I/0 channel check activated by device in EISA slot caused an error |
| hPECCMemory10 | .1.3.6.1.4.1.11.2.23.0.220592 | System memory size reduced due to error in memory slot |
| systemHW15 | .1.3.6.1.4.1.11.2.23.0.220624 | Parity error has occurred on a transfer to or from a device on one of the PCI buses |
| systemHW17 | .1.3.6.1.4.1.11.2.23.0.220640 | System error has occurred in the PCI subsystem |
| aSR4 | .1.3.6.1.4.1.11.2.23.0.220752 | Server has been restarted after the system watchdog timer has timed out due to NOS being hung |
| systemHW31 | .1.3.6.1.4.1.11.2.23.0.220800 | Configuration Utility has altered system configuration |
| redundantPower17 | .1.3.6.1.4.1.11.2.23.0.222705 | Temperature alert on designated Power Supply. |
| redundantPower19 | .1.3.6.1.4.1.11.2.23.0.222706 | Fan failure on designated Power Supply. |
| redundantPower22 | .1.3.6.1.4.1.11.2.23.0.222708 | Fan speed-up on designated Power Supply. |
| temperature7 | .1.3.6.1.4.1.11.2.23.0.224449 | Hot Swap Cage : Temperature monitor error occurred |
| temperature8 | .1.3.6.1.4.1.11.2.23.0.224451 | Hot Swap Cage : Warning temperature exceeded |
| temperature9 | .1.3.6.1.4.1.11.2.23.0.224452 | Hot Swap Cage : Emergency temperature exceeded! |
| systemHW40 | .1.3.6.1.4.1.11.2.23.0.224453 | Power connection failure in one of the devices in the hot swap cage |
| systemHW41 | .1.3.6.1.4.1.11.2.23.0.224454 | A device has been removed from the hot swap cage |
| systemHW42 | .1.3.6.1.4.1.11.2.23.0.224455 | A device has been inserted into the hot swap cage |
| systemHW51 | .1.3.6.1.4.1.11.2.23.0.22528 | The Processor in the indicated slot has been disabled by the BIOS. |
| systemHW57 | .1.3.6.1.4.1.11.2.23.0.22544 | A single or multiple ECC Error has been detected on the P6 bus. |
| hPFan7 | .1.3.6.1.4.1.11.2.23.0.22576 | One of the fans in the Processor/PCI fan tray stopped. |
| hPFan8 | .1.3.6.1.4.1.11.2.23.0.22593 | Two or more of the fans in the Processor/PCI Fan Tray have stopped or have been removed. |
| hPFan9 | .1.3.6.1.4.1.11.2.23.0.22608 | Fan problem in Processor/PCI Fan Tray has been corrected. |
| aSR8 | .1.3.6.1.4.1.11.2.23.0.22624 | The System has been reset by the microcontroller firmware because watchdog timer expired. |
| hPFan10 | .1.3.6.1.4.1.11.2.23.0.22640 | One of the fans in the Memory Fan Tray stopped. |
| systemHW52 | .1.3.6.1.4.1.11.2.23.0.22651 | A user has halted the system with the NMI switch on the front panel. |
| hPFan11 | .1.3.6.1.4.1.11.2.23.0.22657 | Two or more of the fans in the Memory Fan Tray have stopped or been removed. |
| hPFan12 | .1.3.6.1.4.1.11.2.23.0.22672 | Fan problem in the Memory Fan Tray has been corrected. |
| systemHW53 | .1.3.6.1.4.1.11.2.23.0.22688 | Previously disabled Processor has been reinstalled. |
| redundantPower16 | .1.3.6.1.4.1.11.2.23.0.22705 | Temperature alert on designated Power Supply. |
| redundantPower18 | .1.3.6.1.4.1.11.2.23.0.22706 | Fan failure on designated Power Supply. |
| redundantPower20 | .1.3.6.1.4.1.11.2.23.0.22707 | Voltage error on designated Power Supply. |
| redundantPower21 | .1.3.6.1.4.1.11.2.23.0.22708 | Fan speed-up on designated Power Supply. |
| redundantPower23 | .1.3.6.1.4.1.11.2.23.0.22709 | A power supply's 3.3 volt supply has gone bad |
| redundantPower24 | .1.3.6.1.4.1.11.2.23.0.22710 | A power supply's 5 volt supply has gone bad |
| redundantPower25 | .1.3.6.1.4.1.11.2.23.0.22711 | A power supply's 12 volt supply has gone bad |
| redundantPower26 | .1.3.6.1.4.1.11.2.23.0.22712 | A power supply's -12 volt supply has gone bad |
| redundantPower27 | .1.3.6.1.4.1.11.2.23.0.22720 | Indicated Power Supply has been removed or is not connected properly. |
| redundantPower28 | .1.3.6.1.4.1.11.2.23.0.22736 | The indicated Power Supply has been inserted. |
| systemHW54 | .1.3.6.1.4.1.11.2.23.0.22752 | The system has been reset because Control Board detected a critical error. |
| systemHW55 | .1.3.6.1.4.1.11.2.23.0.22768 | The system has been power-cycled because Control Board detected a critical error. |
| systemHW56 | .1.3.6.1.4.1.11.2.23.0.22785 | The Processor Card is missing or not properly terminated in indicated processor module. |
| hPEnvironment7 | .1.3.6.1.4.1.11.2.23.0.22801 | Voltage Regulating Module (VRM) on the indicated processor module had failed. |
| storageCap2 | .1.3.6.1.4.1.11.2.23.0.24096 | Volume Storage Capacity has exceeded the warning threshold level. |
| storageCap4 | .1.3.6.1.4.1.11.2.23.0.24097 | Volume Storage Capacity has exceeded the minor threshold level. |
| storageCap6 | .1.3.6.1.4.1.11.2.23.0.24098 | Volume Storage Capacity has exceeded the major threshold level. |
| systemHW2 | .1.3.6.1.4.1.11.2.23.0.24356 | Post Error has occurred. |
| systemHW3 | .1.3.6.1.4.1.11.2.23.0.24358 | Post Error has occurred. |
| temperature4 | .1.3.6.1.4.1.11.2.23.0.24449 | Hot Swap Cage : Temperature monitor error occurred |
| temperature5 | .1.3.6.1.4.1.11.2.23.0.24451 | Hot Swap Cage : Warning temperature exceeded |
| temperature6 | .1.3.6.1.4.1.11.2.23.0.24452 | Hot Swap Cage : Emergency temperature exceeded! |
| systemHW32 | .1.3.6.1.4.1.11.2.23.0.24453 | Power connection failure in one of the devices in the hot swap cage |
| systemHW34 | .1.3.6.1.4.1.11.2.23.0.24454 | A device has been removed from the hot swap cage |
| systemHW35 | .1.3.6.1.4.1.11.2.23.0.24455 | A device has been inserted into the hot swap cage |
| systemHW45 | .1.3.6.1.4.1.11.2.23.0.24456 | Event log is getting full. |
| hPEnvironment1 | .1.3.6.1.4.1.11.2.23.0.25000 | One of the voltage sensors crossed its lower non-critical threshold. |
| hPEnvironment2 | .1.3.6.1.4.1.11.2.23.0.25001 | One of the voltage sensors crossed its lower critical threshold. |
| hPEnvironment3 | .1.3.6.1.4.1.11.2.23.0.25002 | One of the voltage sensors crossed its lower non-recoverable threshold. |
| hPEnvironment4 | .1.3.6.1.4.1.11.2.23.0.25003 | One of the voltage sensors crossed its upper non-critical threshold. |
| hPEnvironment5 | .1.3.6.1.4.1.11.2.23.0.25004 | One of the voltage sensors crossed its upper critical threshold. |
| hPEnvironment6 | .1.3.6.1.4.1.11.2.23.0.25005 | One of the voltage sensors crossed its upper non-recoverable threshold. |
| systemHW7s | .1.3.6.1.4.1.11.2.23.0.25006 | VRM failure |
| hPTemperature1 | .1.3.6.1.4.1.11.2.23.0.25007 | One of the temperature sensors crossed its lower non-critical threshold. |
| hPTemperature2 | .1.3.6.1.4.1.11.2.23.0.25008 | One of the temperature sensors crossed its lower critical threshold. |
| hPTemperature3 | .1.3.6.1.4.1.11.2.23.0.25009 | One of the temperature sensors crossed its lower non-recoverable threshold. |
| hPTemperature4 | .1.3.6.1.4.1.11.2.23.0.25010 | One of the temperature sensors crossed its upper non-critical threshold. |
| hPTemperature5 | .1.3.6.1.4.1.11.2.23.0.25011 | One of the temperature sensors crossed its upper critical threshold. |
| hPTemperature6 | .1.3.6.1.4.1.11.2.23.0.25012 | One of the temperature sensors crossed its upper non-recoverable threshold. |
| hPFan1 | .1.3.6.1.4.1.11.2.23.0.25013 | One of the fan sensors crossed its lower non-critical threshold. |
| hPFan2 | .1.3.6.1.4.1.11.2.23.0.25014 | One of the fan sensors crossed its lower critical threshold. |
| hPFan3 | .1.3.6.1.4.1.11.2.23.0.25015 | One of the fan sensors crossed its lower non-recoverable threshold. |
| hPFan4 | .1.3.6.1.4.1.11.2.23.0.25016 | One of the fan sensors crossed its upper non-critical threshold. |
| hPFan5 | .1.3.6.1.4.1.11.2.23.0.25017 | One of the fan sensors crossed its upper critical threshold. |
| hPFan6 | .1.3.6.1.4.1.11.2.23.0.25018 | One of the fan sensors crossed its upper non-recoverable threshold. |
| hPChassis1 | .1.3.6.1.4.1.11.2.23.0.25019 | The chassis has been opened. |
| hPChassis2 | .1.3.6.1.4.1.11.2.23.0.25020 | I/O area open |
| hPChassis3 | .1.3.6.1.4.1.11.2.23.0.25021 | Processor area open |
| systemHW80 | .1.3.6.1.4.1.11.2.23.0.25022 | Battery cycles have gone beyond the upper non-critical range |
| systemHW81 | .1.3.6.1.4.1.11.2.23.0.25023 | Battery cycles have gone beyond the upper critical range |
| systemHW82 | .1.3.6.1.4.1.11.2.23.0.25024 | Battery cycles have gone beyond the upper non-recoverable range |
| hPFan13 | .1.3.6.1.4.1.11.2.23.0.25025 | A system fan module error has occurred |
| hPFan14 | .1.3.6.1.4.1.11.2.23.0.25026 | A system fan module error has occurred |
| hPFan15 | .1.3.6.1.4.1.11.2.23.0.25027 | Fan module failure |
| hPFan16 | .1.3.6.1.4.1.11.2.23.0.25028 | Fan module failure |
| systemHW67 | .1.3.6.1.4.1.11.2.23.0.254454 | A SCSI cable has been removed from the hot swap cage. |
| systemHW68 | .1.3.6.1.4.1.11.2.23.0.254455 | A SCSI cable was attached to the hot swap cage. |
| systemHW69 | .1.3.6.1.4.1.11.2.23.0.254456 | A SCSI terminator has been removed from the hot swap cage. |
| systemHW70 | .1.3.6.1.4.1.11.2.23.0.254457 | A SCSI terminator has been attached in the hot swap cage. |
| systemHW84 | .1.3.6.1.4.1.11.2.23.0.25780 | Unrecoverable chipset error has occurred in system board . |
| hPRaid2 | .1.3.6.1.4.1.11.2.23.0.28609 | HPDA Controller: Cache Error |
| hPRaid6 | .1.3.6.1.4.1.11.2.23.0.28641 | HPDA Hot Spare:Failed |
| hPRaid9 | .1.3.6.1.4.1.11.2.23.0.28657 | HPDA Hard Disk Failed |
| hPRaid11 | .1.3.6.1.4.1.11.2.23.0.28673 | HPDA Threshold Exceeded: Parity |
| hPRaid13 | .1.3.6.1.4.1.11.2.23.0.28674 | HPDA Threshold Exceeded: Soft Errors |
| hPRaid15 | .1.3.6.1.4.1.11.2.23.0.28675 | HPDA Threshold Exceeded: Hardware Errors |
| hPRaid17 | .1.3.6.1.4.1.11.2.23.0.28676 | HPDA Threshold Exceeded: Miscellaneous Errors |
| hPRaid19 | .1.3.6.1.4.1.11.2.23.0.28677 | HPDA Controller: NVRAM Age |
| redundantPower29 | .1.3.6.1.4.1.11.2.23.0.29101 | Indicated Power Supply has been removed. |
| redundantPower30 | .1.3.6.1.4.1.11.2.23.0.29102 | The indicated Power Supply has been inserted. |
| redundantPower31 | .1.3.6.1.4.1.11.2.23.0.29103 | The indicated Power Supply Unit power has failed. |
| redundantPower33 | .1.3.6.1.4.1.11.2.23.0.29104 | Power supply subsystem redundancy gained. |
| redundantPower34 | .1.3.6.1.4.1.11.2.23.0.29105 | Power supply sunsystem redundancy lost. |
| redundantPower35 | .1.3.6.1.4.1.11.2.23.0.29106 | The server Power Supply Subsystem has fewer than the required number of Power Supply Units installed for normal operation. |
| redundantPower36 | .1.3.6.1.4.1.11.2.23.0.29107 | The server Power Supply Subsystem has fewer than the required number of Power Supply Units installed for normal operation. |
| redundantPower32 | .1.3.6.1.4.1.11.2.23.0.29109 | Predictive failure/alert in power supply |
| networkCard4 | .1.3.6.1.4.1.11.2.23.0.316385 | The total number of packets with receive errors has exceeded the threshold. |
| networkCard8 | .1.3.6.1.4.1.11.2.23.0.316386 | The total number of packets with transmit errors has exceeded the threshold. |
| networkCard12 | .1.3.6.1.4.1.11.2.23.0.316387 | The total number of LAN Adapter reset errors has exceeded the threshold. |
| networkCard16 | .1.3.6.1.4.1.11.2.23.0.316388 | The total number of alignment and CRC errors has exceeded the threshold. |
| networkCard20 | .1.3.6.1.4.1.11.2.23.0.316389 | The total number of giant frame packets has exceeded the threshold. |
| networkCard24 | .1.3.6.1.4.1.11.2.23.0.316390 | The total number of packets with length less than the required minimum length has exceeded the threshold. |
| networkCard28 | .1.3.6.1.4.1.11.2.23.0.316391 | The total number of late collision errors has exceeded the threshold (the network is too large). |
| networkCard32 | .1.3.6.1.4.1.11.2.23.0.316392 | The total number of colliding packets has exceeded the threshold (the network is too busy). |
| networkCard36 | .1.3.6.1.4.1.11.2.23.0.316393 | The total number of carrier sense errors has exceeded the threshold. |
| networkCard40 | .1.3.6.1.4.1.11.2.23.0.316394 | The total number of adapter deferrals has exceeded the threshold (the network is forever busy). |
| networkCard44 | .1.3.6.1.4.1.11.2.23.0.316395 | The total number of No ECB errors (LAN adapter is out of receive buffers) errors has exceeded the threshold. |
| networkCard48 | .1.3.6.1.4.1.11.2.23.0.316396 | The total number of Receive Overflow errors has exceeded the threshold. |
| networkCard52 | .1.3.6.1.4.1.11.2.23.0.316397 | LAN adapter utilization count has exceeded the threshold. |
| aSR5 | .1.3.6.1.4.1.11.2.23.0.320752 | Server has not been restarted after the system watchdog timer has timed out due to NOS being hung |
| systemHW71 | .1.3.6.1.4.1.11.2.23.0.324454 | A drive has been removed from the hot swap cage |
| systemHW72 | .1.3.6.1.4.1.11.2.23.0.324455 | A drive has been inserted into the hot swap cage |
| systemHW4 | .1.3.6.1.4.1.11.2.23.0.34356 | System boot (POST Complete). |
| systemHW5 | .1.3.6.1.4.1.11.2.23.0.34357 | Netserver Management Controller started |
| systemHW46 | .1.3.6.1.4.1.11.2.23.0.34456 | Event log cleared |
| storageCap1 | .1.3.6.1.4.1.11.2.23.0.4096 | Volume Storage Capacity has exceeded the warning threshold level. |
| storageCap3 | .1.3.6.1.4.1.11.2.23.0.4097 | Volume Storage Capacity has exceeded the minor threshold level. |
| storageCap5 | .1.3.6.1.4.1.11.2.23.0.4098 | Volume Storage Capacity has exceeded the major threshold level. |
| aSR6 | .1.3.6.1.4.1.11.2.23.0.420752 | Server has been powered down after the system watchdog timer has timed out due to NOS being hung |
| systemHW1 | .1.3.6.1.4.1.11.2.23.0.4356 | Post Error has occurred. |
| systemHW47 | .1.3.6.1.4.1.11.2.23.0.44456 | SDR area cleared |
| systemHW83s | .1.3.6.1.4.1.11.2.23.0.44457 | FRU internal use area cleared |
| aSR7 | .1.3.6.1.4.1.11.2.23.0.520752 | Server has been power cycled after the system watchdog timer has timed out due to NOS being hung |
| systemHW100 | .1.3.6.1.4.1.11.2.23.0.53001 | SMART predictive failure detected |
| systemHW33 | .1.3.6.1.4.1.11.2.23.0.54453 | system Voltage failure |
| systemHW36 | .1.3.6.1.4.1.11.2.23.0.54454 | A SCSI cable has been removed from the hot swap cage. |
| systemHW37 | .1.3.6.1.4.1.11.2.23.0.54455 | A SCSI cable was attached to hot swap cage. |
| systemHW38 | .1.3.6.1.4.1.11.2.23.0.54456 | A SCSI terminator has been removed from the hot swap cage. |
| systemHW39 | .1.3.6.1.4.1.11.2.23.0.54457 | A SCSI terminator has been attached in the hot swap cage. |
| systemHW74 | .1.3.6.1.4.1.11.2.23.0.54460 | SCSI Duplex Board has been removed |
| systemHW75 | .1.3.6.1.4.1.11.2.23.0.54461 | SCSI Duplex Board has been inserted |
| systemHW78 | .1.3.6.1.4.1.11.2.23.0.54464 | SCSI Bus Type has changed |
| systemHW76 | .1.3.6.1.4.1.11.2.23.0.54465 | Normal ACPI server shutdown |
| systemHW77 | .1.3.6.1.4.1.11.2.23.0.54466 | ACPI hardware failure |
| hPDiskSystem1 | .1.3.6.1.4.1.11.2.23.0.8210 | The Defect List Threshold has been exceeded. |
| hPRaid1 | .1.3.6.1.4.1.11.2.23.0.8609 | HPDA Controller: Cache Error |
| hPRaid3 | .1.3.6.1.4.1.11.2.23.0.8625 | HPDA Logical Drive: Critical |
| hPRaid4 | .1.3.6.1.4.1.11.2.23.0.8626 | HPDA Logical Drive Not Available |
| hPRaid5 | .1.3.6.1.4.1.11.2.23.0.8641 | HPDA Hot Spare:Failed |
| hPRaid7 | .1.3.6.1.4.1.11.2.23.0.8642 | HPDA Hot Spare Succeeded |
| hPRaid8 | .1.3.6.1.4.1.11.2.23.0.8657 | HPDA Hard Disk Failed |
| hPRaid10 | .1.3.6.1.4.1.11.2.23.0.8673 | HPDA Threshold Exceeded: Parity |
| hPRaid12 | .1.3.6.1.4.1.11.2.23.0.8674 | HPDA Threshold Exceeded: Soft Errors |
| hPRaid14 | .1.3.6.1.4.1.11.2.23.0.8675 | HPDA Threshold Exceeded: Hardware Errors |
| hPRaid16 | .1.3.6.1.4.1.11.2.23.0.8676 | HPDA Threshold Exceeded: Miscellaneous Errors |
| hPRaid18 | .1.3.6.1.4.1.11.2.23.0.8677 | HPDA Controller: NVRAM Age |
| redundantPower1 | .1.3.6.1.4.1.11.2.23.0.9101 | The Redundant Power Supply module is not operating properly, but there is no power supply module hardware failure. |
| redundantPower2 | .1.3.6.1.4.1.11.2.23.0.9103 | Indicates a failure with the AC power source that is connected to one of the redundant power supply units. |
| redundantPower4 | .1.3.6.1.4.1.11.2.23.0.9105 | Indicates that one of the redundant power supply modules is not in normal operating condition. |
| redundantPower5 | .1.3.6.1.4.1.11.2.23.0.9106 | Indicates that one of the redundant power supply modules is in over temperature protection mode. |
| redundantPower7 | .1.3.6.1.4.1.11.2.23.0.9107 | Indicates that one of the redundant power supply modules has been physically removed from the HP NetServer Power Supply Subsystem. |
| redundantPower8 | .1.3.6.1.4.1.11.2.23.0.9108 | Indicates that one of the redundant power supply modules has been physically inserted into the HP NetServer Power Supply Subsystem. |
| redundantPower9 | .1.3.6.1.4.1.11.2.23.0.9109 | Indicates that one of the redundant power supply modules in the HP NetServer has recovered from an over temperature protection mode. |
| redundantPower11 | .1.3.6.1.4.1.11.2.23.0.9110 | Indicates that one of the redundant power supply modules in the HP NetServer has exceeded the warning temperature level. |
| redundantPower13 | .1.3.6.1.4.1.11.2.23.0.9111 | Indicates that one of the redundant power supply modules in the HP NetServer has exceeded the emergency temperature level. |
| redundantPower14 | .1.3.6.1.4.1.11.2.23.0.9112 | Power System failure A/C Lost |
| redundantPower15 | .1.3.6.1.4.1.11.2.23.0.9113 | The Power Supply Subsystem has fewer than the required number of Power Supply Units installed for normal operation or is having problems powering up or down. |
| redundantPower37 | .1.3.6.1.4.1.11.2.23.0.9114 | Power Supply Subsystem soft failure |
| hPECCMemory2 | .1.3.6.1.4.1.11.2.23.6.0.24353 | A single-bit error has been corrected in one of the memory modules. |
| hPECCMemory3 | .1.3.6.1.4.1.11.2.23.6.0.24354 | Predictive failure in a memory module |
| hPECCMemory7 | .1.3.6.1.4.1.11.2.23.6.0.24357 | A Multiple-bit error has occurred in one of the memory modules |
| hPECCMemory9 | .1.3.6.1.4.1.11.2.23.6.0.24359 | Single-bit repeated error |
| hPECCMemory11 | .1.3.6.1.4.1.11.2.23.6.0.4360 | ECC error corrected in memory module |
| hPECCMemory12 | .1.3.6.1.4.1.11.2.23.6.0.4361 | Uncorrectable multi-bit ECC error has occurred in memory module |
| hPECCMemory13 | .1.3.6.1.4.1.11.2.23.6.0.4363 | Repeated ECC error corrected in memory module |
| hPECCMemory14 | .1.3.6.1.4.1.11.2.23.6.0.4364 | ECC memory module is operating outside of acceptable margins |
| hPECCMemory15 | .1.3.6.1.4.1.11.2.23.6.0.4365 | Memory Mirroring switched to Slave Set |
| hPECCMemory16 | .1.3.6.1.4.1.11.2.23.6.0.4366 | Faulty row switched to Hot Spare row |
| rAVoltage1 | .1.3.6.1.4.1.11.2.23.8.0.109 | The server has lost the power completely. |
| rAVoltage2 | .1.3.6.1.4.1.11.2.23.8.0.111 | Voltage measured in the server has gone outside of -12V Upper Threshold. |
| rAVoltage3 | .1.3.6.1.4.1.11.2.23.8.0.113 | Voltage measured in the server has gone outside of +3.3V Upper Threshold. |
| rAVoltage4 | .1.3.6.1.4.1.11.2.23.8.0.114 | Voltage measured in the server has gone outside of +5V Upper Threshold. |
| rAVoltage5 | .1.3.6.1.4.1.11.2.23.8.0.115 | Voltage measured in the server has gone outside of +12V Upper Threshold. |
| rAVoltage6 | .1.3.6.1.4.1.11.2.23.8.0.121 | Voltage measured in the server has gone outside of -12V Lower Threshold. |
| rAVoltage10 | .1.3.6.1.4.1.11.2.23.8.0.122 | The HP Remote Assistant Card's battery charging circuit is bad. |
| rAVoltage7 | .1.3.6.1.4.1.11.2.23.8.0.123 | Voltage measured in the server has gone outside of +3.3V Lower Threshold. |
| rAVoltage8 | .1.3.6.1.4.1.11.2.23.8.0.124 | Voltage measured in the server has gone outside of +5V Lower Threshold. |
| rAVoltage9 | .1.3.6.1.4.1.11.2.23.8.0.125 | Voltage measured in the server has gone outside of +12V Lower Threshold. |
| rAOther10 | .1.3.6.1.4.1.11.2.23.8.0.1602 | A remote user has executed a remote power cycle on the server via the HP RA or Remote Control. |
| rAOther13 | .1.3.6.1.4.1.11.2.23.8.0.1603 | A remote user has executed a remote power down of the server via the HP RA or Remote Control card. |
| rATemp1 | .1.3.6.1.4.1.11.2.23.8.0.211 | The server temperature measured on the HP Remote Assistant Card has exceeded the configured warning threshold. |
| rATemp2 | .1.3.6.1.4.1.11.2.23.8.0.221 | The server temperature measured on the HP Remote Assistant Card has exceeded the configured threshold and the server has been automatically shut down. |
| rATemp3 | .1.3.6.1.4.1.11.2.23.8.0.2221 | The server temperature or voltage levels measured by the remote management hardware has exceeded the configured threshold. The server has been automatically shut down. |
| rATemp4 | .1.3.6.1.4.1.11.2.23.8.0.231 | The server temperature measured on the HP Remote Assistant Card has exceeded the configured Graceful Shutdown threshold value by 5 degrees C and the server has been automatically shut down. |
| rAOther2 | .1.3.6.1.4.1.11.2.23.8.0.2401 | A remote user has logged in to the HP RA or Remote Control card. |
| rAOther4 | .1.3.6.1.4.1.11.2.23.8.0.2402 | An unauthorized user has made 3 or more unsuccessful attempts to log in to the HP RA or Remote Control card. |
| rAOther22 | .1.3.6.1.4.1.11.2.23.8.0.2406 | A remote user has been automatically disconnected from the HP RA or Remote Control card, because of inactivity. |
| rAOther24 | .1.3.6.1.4.1.11.2.23.8.0.2407 | A remote user has been prematurely disconnected from the HP RA or Remote Control card. |
| rAOther26 | .1.3.6.1.4.1.11.2.23.8.0.2408 | A remote user failed to connect to the HP RA or Remote Control on a dialback |
| rAOther8 | .1.3.6.1.4.1.11.2.23.8.0.2601 | An administrator has executed a remote on the server via the HP RA or Remote Control card. |
| rAOther17 | .1.3.6.1.4.1.11.2.23.8.0.2604 | A remote user has executed a remote graceful shutdown of the server via the HP RA or Remote Control card. |
| rAOther30 | .1.3.6.1.4.1.11.2.23.8.0.2901 | The HP RA or Remote Control modem was unable to connect to the TAP paging service modem. |
| rAOther33 | .1.3.6.1.4.1.11.2.23.8.0.2902 | The HP RA or Remote Control was unable to connect to the TAP paging service. |
| rAOther34 | .1.3.6.1.4.1.11.2.23.8.0.2903 | The HP RA or Remote Control was unable to log on to the TAP paging service. |
| rAOther36 | .1.3.6.1.4.1.11.2.23.8.0.2904 | The HP RA or Remote Control pager message was rejected by the TAP paging service. |
| rAOther37 | .1.3.6.1.4.1.11.2.23.8.0.2905 | The HP RA or Remote Control email notification message was not sent correctly. |
| rAOther38 | .1.3.6.1.4.1.11.2.23.8.0.2906 | A modem error has been detected on the remote management card. |
| rAOther39 | .1.3.6.1.4.1.11.2.23.8.0.2907 | TopTools Remote Control Card memory test started |
| rAOther40 | .1.3.6.1.4.1.11.2.23.8.0.2908 | TopTools Remote Control Card memory test completed |
| rAOther41 | .1.3.6.1.4.1.11.2.23.8.0.2909 | TopTools Remote Control Card memory test stopped by user |
| rAOther42 | .1.3.6.1.4.1.11.2.23.8.0.2910 | TopTools Remote Control Card memory test error |
| rAOther43 | .1.3.6.1.4.1.11.2.23.8.0.2911 | TopTools Remote Control Card started |
| rAOther44 | .1.3.6.1.4.1.11.2.23.8.0.2912 | TopTools Remote Control Card detects a serious internal error that prevents normal operation of the card |
| rAOther45 | .1.3.6.1.4.1.11.2.23.8.0.2913 | The firmware on the TopTools Remote Control has been updated |
| rAOther46 | .1.3.6.1.4.1.11.2.23.8.0.2914 | The TopTools Remote Control backup battery has discharged to a level where it will not be able to power the card |
| rAOther47 | .1.3.6.1.4.1.11.2.23.8.0.2915 | The battery on the TopTools Remote Control card is disconnected |
| rAOther48 | .1.3.6.1.4.1.11.2.23.8.0.2916 | Remote Control Card: DHCP has assigned a new IP address |
| rAOther27 | .1.3.6.1.4.1.11.2.23.8.0.3408 | Integrated RA configuration reset to defaults |
| rAOther11 | .1.3.6.1.4.1.11.2.23.8.0.3602 | A remote user has executed a remote hard reset on the server via the HP RA or Remote Control. |
| rAOther14 | .1.3.6.1.4.1.11.2.23.8.0.3603 | A remote user has executed a remote power up of the server via the HP RA or Remote Control card. |
| rAOther1 | .1.3.6.1.4.1.11.2.23.8.0.401 | An administrator has logged in to the HP Remote Assistant Card. |
| rAOther3 | .1.3.6.1.4.1.11.2.23.8.0.402 | An unauthorized user has made 3 or more unsuccessful attempts to log in to the HP Remote Assistant Card within a 5-minute period of time. |
| rAOther5 | .1.3.6.1.4.1.11.2.23.8.0.403 | The HP Remote Assistant Card's battery charging circuit is bad. |
| rAOther6 | .1.3.6.1.4.1.11.2.23.8.0.404 | The HP Remote Assistant Card has been shut down. |
| rAOther20 | .1.3.6.1.4.1.11.2.23.8.0.405 | A remote user disconnected from the HP RA or Remote Control card. |
| rAOther21 | .1.3.6.1.4.1.11.2.23.8.0.406 | An administrator has been automatically disconnected from the HP Remote Assistant board. The administrator was inactive for more than five minutes. |
| rAOther23 | .1.3.6.1.4.1.11.2.23.8.0.407 | An administrator has been prematurely disconnected from the Remote Assistant board. |
| rAOther25 | .1.3.6.1.4.1.11.2.23.8.0.408 | An administrator failed to connect to the HP Remote Assistant board on a dialback |
| rAOther28 | .1.3.6.1.4.1.11.2.23.8.0.4408 | TopTools Remote Control card configuration was corrupted and has been restored to default settings. |
| rAOther15 | .1.3.6.1.4.1.11.2.23.8.0.4603 | Automatic power shutdown due to critical condition. |
| rAASR1 | .1.3.6.1.4.1.11.2.23.8.0.501 | ASR has stopped notifying the HP Remote Assistant Card that the system is running correctly (the server probably hung or crashed). |
| rAASR2 | .1.3.6.1.4.1.11.2.23.8.0.502 | The HP Remote Assistant card has restarted the server due to the NOS being hung. |
| rAASR3 | .1.3.6.1.4.1.11.2.23.8.0.503 | The Automatic Server Restart software has been enabled by the Remote Assistant ASR timer. |
| rAASR4 | .1.3.6.1.4.1.11.2.23.8.0.504 | The HP Remote Assistant Automatic Server Restart timer has been disabled. |
| rAOther16 | .1.3.6.1.4.1.11.2.23.8.0.5603 | Front panel power down. |
| rAOther7 | .1.3.6.1.4.1.11.2.23.8.0.601 | An administrator has executed a remote on the server via the HP Remote Assistant Card. |
| rAOther9 | .1.3.6.1.4.1.11.2.23.8.0.602 | An administrator has executed a remote power cycle on the server via the HP Remote Assistant Card. |
| rAOther12 | .1.3.6.1.4.1.11.2.23.8.0.603 | An administrator has executed a remote power down of the server via the HP Remote Assistant Card. |
| rAOther18 | .1.3.6.1.4.1.11.2.23.8.0.701 | The server's BIOS has successfully initialized the HP Remote Assistant Card during the boot process. |
| rABusUsage1 | .1.3.6.1.4.1.11.2.23.8.0.800 | The 5-minute average EISA bus utilization has exceeded the configured threshold. |
| rAOther19 | .1.3.6.1.4.1.11.2.23.8.0.900 | An administrator has executed Test Page from the HP Remote Assistant Configuration Utility. |
| rAOther29 | .1.3.6.1.4.1.11.2.23.8.0.901 | The HP Remote Assistant modem was unable to connect to the TAP paging service modem. |
| rAOther31 | .1.3.6.1.4.1.11.2.23.8.0.902 | HP Remote Assistant was unable to connect with the TAP paging service. |
| rAOther32 | .1.3.6.1.4.1.11.2.23.8.0.903 | HP Remote Assistant was unable to log on to the TAP paging service. |
| rAOther35 | .1.3.6.1.4.1.11.2.23.8.0.904 | The HP Remote Assistant pager message was rejected |
| sCSISmart22 | .1.3.6.1.4.1.795.2.5.0.126 | Aspi: initializing |
| adaptecSCSI2 | .1.3.6.1.4.1.795.4.1.0.18193 | Device Database has been corrupted. |
| adaptecSCSI4 | .1.3.6.1.4.1.795.4.1.0.18194 | SCSI Status agent was unloaded from a NetWare Server. |
| adaptecSCSI6 | .1.3.6.1.4.1.795.4.1.0.18196 | One of the SCSI HBAs can no longer be detected by the SCSI Status agent. |
| adaptecSCSI8 | .1.3.6.1.4.1.795.4.1.0.18197 | A Host Adapter which has failed, has become accessible again. |
| adaptecSCSI10 | .1.3.6.1.4.1.795.4.1.0.18198 | A new SCSI Host Bus Adapter has been discovered or device database has been cleared. |
| adaptecSCSI12 | .1.3.6.1.4.1.795.4.1.0.18199 | One of the SCSI devices installed on the server can no longer be detected by the SCSI Status agent. |
| adaptecSCSI14 | .1.3.6.1.4.1.795.4.1.0.18200 | A SCSI device which has failed, has become accessible again. |
| adaptecSCSI16 | .1.3.6.1.4.1.795.4.1.0.18201 | A new SCSI device has been discovered. |
| adaptecSCSI18 | .1.3.6.1.4.1.795.4.1.0.18205 | The SCSI Status agent detected that the Host Bus Adapter has been changed. |
| adaptecSCSI22 | .1.3.6.1.4.1.795.4.1.0.18206 | The SCSI Status agent detected that a SCSI device installed on the server has been changed. |
| adaptecSCSI20 | .1.3.6.1.4.1.795.4.1.0.18208 | The SCSI Status agent sent a request to an HBA and the request never completed. |
| adaptecSCSI24 | .1.3.6.1.4.1.795.4.1.0.18209 | The SCSI Status agent sent a request to a SCSI device and the request never completed. |
| adaptecSCSI1 | .1.3.6.1.4.1.795.4.1.0.8193 | Device Database has been corrupted. |
| adaptecSCSI3 | .1.3.6.1.4.1.795.4.1.0.8194 | SCSI Status agent was unloaded from a NetWare Server. |
| adaptecSCSI5 | .1.3.6.1.4.1.795.4.1.0.8196 | One of the SCSI HBAs can no longer be detected by the SCSI Status agent. |
| adaptecSCSI7 | .1.3.6.1.4.1.795.4.1.0.8197 | A Host Adapter which has failed, has become accessible again. |
| adaptecSCSI9 | .1.3.6.1.4.1.795.4.1.0.8198 | A new SCSI Host Bus Adapter has been discovered or device database has been cleared. |
| adaptecSCSI11 | .1.3.6.1.4.1.795.4.1.0.8199 | One of the SCSI devices installed on the server can no longer be detected by the SCSI Status agent. |
| adaptecSCSI13 | .1.3.6.1.4.1.795.4.1.0.8200 | A SCSI device which has failed, has become accessible again. |
| adaptecSCSI15 | .1.3.6.1.4.1.795.4.1.0.8201 | A new SCSI device has been discovered. |
| adaptecSCSI17 | .1.3.6.1.4.1.795.4.1.0.8205 | The SCSI Status agent detected that the Host Bus Adapter has been changed. |
| adaptecSCSI21 | .1.3.6.1.4.1.795.4.1.0.8206 | The SCSI Status agent detected that a SCSI device installed on the server has been changed. |
| adaptecSCSI19 | .1.3.6.1.4.1.795.4.1.0.8208 | The SCSI Status agent sent a request to an HBA and the request never completed. |
| adaptecSCSI23 | .1.3.6.1.4.1.795.4.1.0.8209 | The SCSI Status agent sent a request to a SCSI device and the request never completed. |
hp 