HPN-ICF-EFM-COMMON-MIB Table View

Primary controls and status for the OAM capabilities of an
Ethernet like interface.  There will be one row in this table
for each Ethernet like interface in the system that supports
the Ethernet OAM functions defined in [802.3ah].

hpnicfDot3OamEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1

An entry in the table, containing information on the Ethernet
OAM function for a single Ethernet like interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hpnicfDot3OamAdminState This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The hpnicfDot3OamAdminState always starts in t…	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.1
hpnicfDot3OamOperStatus At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this initialization …	Enumeration Enumerated Values: 1 disabled 2 linkfault 3 passiveWait 4 activeSendLocal 5 sendLocalAndRemote 6 sendLocalAndRemoteOk 7 oamPeeringLocallyRejected 8 oamPeeringRemotelyRejected 9 operational	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.2
hpnicfDot3OamMode This object configures the mode of OAM operation for this Ethernet like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional c…	Enumerationr/w Enumerated Values: 1 active 2 passive	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.3
hpnicfDot3OamMaxOamPduSize The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local impl…	Integer32 Constraints: range: 64-1522	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.4
hpnicfDot3OamConfigRevision The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate configuration changes have occured which might require the …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.5
hpnicfDot3OamFunctionsSupported The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently …	Bits Enumerated Values: 0 unidirectionalSupport 1 loopbackSupport 2 eventSupport 3 variableSupport	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.1.1.6

Information about the OAM peer for a particular Ethernet like
interface. OAM entities communicate with a single OAM peer
entity on full-duplex Ethernet links on which OAM is enabled
and operating properly.
          
In certain states, the OAM peer information is not available.
Whether peer information is available is communicated via the
hpnicfDot3OamPeerStatus object.  When this object is inactive, all
other information in the row is to be considered invalid.

hpnicfDot3OamPeerEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1

An entry in the table, containing information on the peer OAM
entity for a single Ethernet like interface.

Note that there is at most one OAM peer for each Ethernet like
interface. There is exactly one row…

Indexes

IF-MIBifIndex

Column	Syntax	OID
hpnicfDot3OamPeerStatus This object indicates whether the information in this row should be considered valid. When active(1), the information is valid and represents the current peer of the OAM entity. When inactive(2), the information in thi…	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.1
hpnicfDot3OamPeerMacAddress The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU. This value is initialized to all zeros (0x000000000000). This value is invalid if the hpnicfDot3OamPeerStatus…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.2
hpnicfDot3OamPeerVendorOui The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OAM entity. This value is initialized to all zeros …	Dot3Oui Type Constraints: range: 3	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.3
hpnicfDot3OamPeerVendorInfo The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The vendor information field is within the Local Information TLV, and can be used to determine additi…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.4
hpnicfDot3OamPeerMode The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last…	Enumeration Enumerated Values: 1 active 2 passive 3 unknown	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.5
hpnicfDot3OamPeerMaxOamPduSize The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The max…	Integer32 Constraints: range: 64-1522	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.6
hpnicfDot3OamPeerConfigRevision The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OAM this interface. This value is initializ…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.7
hpnicfDot3OamPeerFunctionsSupported The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to t…	Bits Enumerated Values: 0 unidirectionalSupport 1 loopbackSupport 2 eventSupport 3 variableSupport	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.2.1.8

This table contains methods to control the loopback state of
the local link as well as indicating the status of the
loopback function.
          
Loopback can be used to place the remote OAM entity in a state
where every received frame (except OAMPDUs) are echoed back
over the same interface on which they were received.   In this
state, at the remote entity, 'normal' traffic is disabled as
only the looped back frames are transmitted on the interface.
Loopback is thus an intrusive operation that prohibits normal
data flow and should be used accordingly.

hpnicfDot3OamLoopbackEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.3.1

An entry in the table, containing information on the loopback
status for a single Ethernet like interface. There is an
entry in this table for every Ethernet like interface on which
supports OAM and loopback function w…

Indexes

IF-MIBifIndex

Column	Syntax	OID
hpnicfDot3OamLoopbackCommand This attribute initiates or terminates remote loopback with an OAM peer. Writing startRemoteLoopback(2) to this attribute cause the local OAM client to send a loopback OAMPDU to the OAM peer with the loopback enable fl…	Enumerationr/w Enumerated Values: 1 noLoopback 2 startRemoteLoopback 3 stopRemoteLoopback	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.3.1.1
hpnicfDot3OamLoopbackStatus The loopback status of the OAM entity. This status is determined by a combination of the local parser and multiplexer states, the remote parser and multiplexer states, as well as by the actions of the local OAM client.…	Enumeration Enumerated Values: 1 noLoopback 2 initiatingLoopback 3 remoteLoopback 4 terminatingLoopback 5 localLoopback 6 unknown	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.3.1.2
hpnicfDot3OamLoopbackIgnoreRx Since OAM loopback is a distruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value i…	Enumerationr/w Enumerated Values: 1 ignore 2 process	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.3.1.3

Statistics for the OAM function on a particular Ethernet like
interface.

hpnicfDot3OamStatsEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1

An entry in the table, containing statistics information on
the Ethernet OAM function for a single Ethernet like
interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hpnicfDot3OamInformationTx A count of the number of Information OAMPDUs transmitted on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address f…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.1
hpnicfDot3OamInformationRx A count of the number of Information OAMPDUs received on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.2
hpnicfDot3OamUniqueEventNotificationTx A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a frame ma…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.3
hpnicfDot3OamUniqueEventNotificationRx A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a fram…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.4
hpnicfDot3OamDuplicateEventNotificationTx A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.5
hpnicfDot3OamDuplicateEventNotificationRx A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possiblity that a f…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.6
hpnicfDot3OamLoopbackControlTx A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Conrol OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.7
hpnicfDot3OamLoopbackControlRx A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Control OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.8
hpnicfDot3OamVariableRequestTx A count of the number of Variable Request OAMPDUs transmitted on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.9
hpnicfDot3OamVariableRequestRx A count of the number of Variable Request OAMPDUs received on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC ad…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.10
hpnicfDot3OamVariableResponseTx A count of the number of Variable Response OAMPDUs transmitted on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved M…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.11
hpnicfDot3OamVariableResponseRx A count of the number of Variable Response OAMPDUs received on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.12
hpnicfDot3OamOrgSpecificTx A count of the number of Organization Specific OAMPDUs transmitted on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the re…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.13
hpnicfDot3OamOrgSpecificRx A count of the number of Organization Specific OAMPDUs received on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reser…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.14
hpnicfDot3OamUnsupportedCodesTx A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. An unsupported opcode OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of th…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.15
hpnicfDot3OamUnsupportedCodesRx A count of the number of OAMPDUs received on this interface with an unsupported op-code. An unsupported opcode OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the re…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.16
hpnicfDot3OamFramesLostDueToOam A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM mulitplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contenti…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.4.1.17

Ethernet OAM includes the ability to generate and receive
event notifications to indicate various link problems.  This
table contains the mechanisms to configure the thresholds to
generate the standard Ethernet OAM events.
          
These events are:
  - Errored Symbol Period Event.  Generated when the number of
    symbol errors exceeds a threshold within a given window
    defined by a number of symbols (e.g. 1,000 symbols out of
    1,000,000 had errors).
  - Errored Frame Period Event.  Generated when the number of
    frame errors exceeds a threshold within a given window
    defined by a number of frames (e.g. 10 frames out of 1000
    had errors).
  - Errored Frame Event.  Generated when the number of frame
    errors exceeds a threshold within a given window defined
    by a period of time (e.g. 10 frames in 1 second had
    errors).
  - Errored Frame Seconds Summary Event.  Generated when the
    number of errored frame seconds exceeds a threshold within
    a given time period (e.g. 10 errored frame seconds within
    the last 100 seconds).  An errored frame second is defined
    as a 1 second interval which had >0 frame errors.

hpnicfDot3OamEventConfigEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1

Event configuration information is available for every
Ethernet like interface that supports OAM and the event
function of OAM as indicated in the hpnicfDot3OamFunctionsSupported
attribute.

Event configurat…

Indexes

IF-MIBifIndex

Column	Syntax	OID
hpnicfDot3OamErrSymPeriodWindowHi The two objects hpnicfDot3OamErrSymPeriodWindowHi and hpnicfDot3OamErrSymPeriodLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.1
hpnicfDot3OamErrSymPeriodWindowLo The two objects hpnicfDot3OamErrSymPeriodWindowHi and hpnicfDot3OamErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is de…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.2
hpnicfDot3OamErrSymPeriodThresholdHi The two objects hpnicfDot3OamErrSymPeriodThresholdHi and hpnicfDot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to ca…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.3
hpnicfDot3OamErrSymPeriodThresholdLo The two objects hpnicfDot3OamErrSymPeriodThresholdHi and hpnicfDot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to ca…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.4
hpnicfDot3OamErrSymPeriodEvNotifEnable Indicates whether the occurence of Errored Symbol Period Events should result in Event Notification OAMPDUs generated by the OAM layer. By default, this object should have the value enabled(1) for Etherne…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.5
hpnicfDot3OamErrFramePeriodWindow The number of frames over which the threshold is defined. If hpnicfDot3OamErrFramePeriodThreshold frame errors occur within a window of hpnicfDot3OamErrFramePeriodWindow frames, an Event Notification OAMP…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.6
hpnicfDot3OamErrFramePeriodThreshold The number of frame errors that must occur for this event to be triggered. If hpnicfDot3OamErrFramePeriodThreshold frame errors occur within a window of hpnicfDot3OamErrFramePeriodWindow frames, an Event …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.7
hpnicfDot3OamErrFramePeriodEvNotifEnable Indicates whether the occurence of an Errored Frame Period Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethe…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.8
hpnicfDot3OamErrFrameWindow The amount of time (in 100ms increments) over which the threshold is defined. If hpnicfDot3OamErrFrameThreshold frame errors occur within a window of hpnicfDot3OamErrFrameWindow seconds (measured in tenth…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.9
hpnicfDot3OamErrFrameThreshold The number of frame errors that must occur for this event to be triggered. If hpnicfDot3OamErrFrameThreshold frame errors occur within a window of hpnicfDot3OamErrFrameWindow (in tenths of seconds), an Ev…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.10
hpnicfDot3OamErrFrameEvNotifEnable Indicates whether the occurence of an Errored Frame Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet li…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.11
hpnicfDot3OamErrFrameSecsSummaryWindow The amount of time (in 100ms intervals) over which the threshold is defined. If hpnicfDot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of hpnicfDot3OamErrFrameSecsSummaryWindow (in t…	Integer32r/w Constraints: range: 100-9000	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.12
hpnicfDot3OamErrFrameSecsSummaryThreshold The number of errored frame seconds that must occur for this event to be triggered. If hpnicfDot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of hpnicfDot3OamErrFrameSecsSummaryWindo…	Integer32r/w Constraints: range: 1-900	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.13
hpnicfDot3OamErrFrameSecsEvNotifEnable Indicates whether the occurence of an Errored Frame Seconds Summary Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1)…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.5.1.14

This table records a history of the events that have occurred
at the Ethernet OAM level.  These events can include locally
detected events, which may result in locally generated
OAMPDUs, and remotely detected events, which are detected by
the OAM peer entity and signaled to the local entity via
Ethernet OAM.  Ethernet OAM events can be signaled by Event
Notification OAMPDUs or by the flags field in any OAMPDU.

hpnicfDot3OamEventLogEntry row .1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1

An entry in the hpnicfDot3OamEventLogTable.

Indexes

IF-MIBifIndex hpnicfDot3OamEventLogIndex

Column	Syntax	OID
hpnicfDot3OamEventLogIndex An arbitrary integer for identifiying individual events within the event log.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.1
hpnicfDot3OamEventLogTimestamp The date and time that this event instance occurred.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.2
hpnicfDot3OamEventLogOui The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining th…	Dot3Oui Type Constraints: range: 3	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.3
hpnicfDot3OamEventLogType The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFramePeriodEvent …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.4
hpnicfDot3OamEventLogLocation Whether this event occurred locally, or was received from the OAM peer via Ethernet OAM.	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.5
hpnicfDot3OamEventLogWindowHi If the event represents a threshold crossing event, the two objects hpnicfDot3OamEventWindowHi and hpnicfDot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.6
hpnicfDot3OamEventLogWindowLo If the event represents a threshold crossing event, the two objects hpnicfDot3OamEventWindowHi and hpnicfDot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.7
hpnicfDot3OamEventLogThresholdHi If the event represents a threshold crossing event, the two objects hpnicfDot3OamEventThresholdHi and hpnicfDot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold c…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.8
hpnicfDot3OamEventLogThresholdLo If the event represents a threshold crossing event, the two objects hpnicfDot3OamEventThresholdHi and hpnicfDot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold c…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.9
hpnicfDot3OamEventLogValue If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (e.g. 11, when 11 occurrences happened in 5 seconds while the thresho…	HCNUM-TCCounterBasedGauge64	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.10
hpnicfDot3OamEventLogRunningTotal This value respresents the total number of times this occurence has happened since the last reset (e.g. 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold c…	HCNUM-TCCounterBasedGauge64	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.11
hpnicfDot3OamEventLogEventTotal This value respresents the total number of times one or more of these occurences have resulted in an event (e.g. 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error thres…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.15.2.42.3.1.6.1.12