HP-TUNNEL-MIB Table View

This table is used to provision for a tunnel without 
having to configure the source and destination ends of the tunnels.

hpTunnelConfigEntry row .1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1

A set of objects that are used to create a tunnel.

Indexes

hpTunnelID

Column	Syntax	OID
hpTunnelID The tunnel number to configure a tunnel.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.1
hpTunnelIfIndexdeprecated The interface index associated with this tunnel entry. Since this Object is read-only, it is deprecated in favor of hpTunnelInterfaceIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.2
hpTunnelRowStatus The status of this row, by which new entries may be created, or old entries deleted from this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.3
hpTunnelInterfaceIndex The tunnel interface index associated with this tunnel entry.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.1.1.4

This table augments the tunnelIfTable

hpTunnelIfEntry row .1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1

A set of objects as an augment to tunnelIfTable.

Indexes

No indexes recorded

Column	Syntax	OID
hpTunnelIfPMTU Enable/Disable path mtu discovery for this tunnel.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.1
hpTunnelIfNUD Enable/Disable Neighbor Unreachability Detection for this tunnel.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.2
hpTunnelIfMTU The size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that ca…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.3
hpTunnelEncapsMethod The encapsulation method used by the tunnel.	HpTunnelTyper/w Type Values: 1 unspecified 2 direct4in4 3 direct6in4 4 direct6in4Ipsec 5 direct6in6 6 ipsecIpv4 7 ipsecIpv6 8 macinudp	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.4
hpTunnelIpsecName Specifies the IPSEC profile name for tunnel. This mentioned IPSEC profile can be attached with tunnel to avail the protection for tunnel traffic	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.2.1.5

This table augments the tunnelInetConfigTable

hpTunnelInetConfigEntry row .1.3.6.1.4.1.11.2.14.11.5.1.77.1.3.1

A set of objects as an augment to tunnelInetConfigTable.

Indexes

No indexes recorded

Column	Syntax	OID
hpTunnelInetConfigEncapsMethod The encapsulation method used by the tunnel.	HpTunnelTyper/w Type Values: 1 unspecified 2 direct4in4 3 direct6in4 4 direct6in4Ipsec 5 direct6in6 6 ipsecIpv4 7 ipsecIpv6 8 macinudp	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.3.1.1

A table that maps a VLAN to a tunnel. The tunnel to VLAN mapping                implies that tunnel will carry bidirectional traffic of a VLAN.

hpicfVlanTunnelMappingEntry row .1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1

An entry containing the mapping of a VLAN to a tunnel.
The VLAN-to-tunnel mapping allows all the VLAN traffic to
flow through the associated tunnel.

Indexes

hpicfVLANIndex hpicfTunnelIfIndex

Column	Syntax	OID
hpicfVLANIndex This object refers to the VLANID that is mapped to a tunnel	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.1
hpicfTunnelIfIndex This object specifies the tunnel interface index which is mapped to a speciifc VLAN.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.2
hpicfVlanTunnelMappingRowStatus The row status of a VLAN to tunnel mapping entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.4.1.3

A table containing the information about the UDP tunnel types.

hpicfUDPTunnelTypeEntry row .1.3.6.1.4.1.11.2.14.11.5.1.77.1.5.1

An entry containing the information on a UDP tunnel type.

Indexes

No indexes recorded

Column	Syntax	OID
hpicfUDPTunnelType This object is used to configure the UDP tunnel type. A value of none(0) indicates that the tunnel is not a UDP tunnel. A value of remotemirror(1) indicates that the UDP tunnel configured is a remote mirroring tun…	Enumerationr/w Enumerated Values: 0 none 1 remotemirror 2 vxlan	.1.3.6.1.4.1.11.2.14.11.5.1.77.1.5.1.1