HP-SN-MPLS-TE-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
7
Rows
7
Columns
94

mplsTunnelTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2 · 1 row entry · 37 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelTable' 
The mplsTunnelTable allows new MPLS tunnels to be
created between an LSR and a remote endpoint, and
existing tunnels to be reconfigured or removed.
Note that only point-to-point tunnel segments are
supported, although multi-point-to-point and point-
to-multi-point connections are supported by an LSR
acting as a cross-connect.  Each MPLS tunnel can
thus have one out-segment originating at this LSR
and/or one in-segment terminating at this LSR.
mplsTunnelEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1
An entry in this table represents an MPLS tunnel.
An entry can be created by a network administrator
or by an SNMP agent as instructed by an MPLS
signaling protocol. Whenever a new entry is created
with mplsTunnelIsIf s…
Indexes
Column Syntax OID
mplsTunnelIndex
Uniquely identifies this row.
HP-SN-MPLS-TC-MIBMplsTunnelIndex
Type Constraints:
range: 1..65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.1
mplsTunnelInstance
Uniquely identifies an instance of a tunnel. It is
useful to identify multiple instances of tunnels
for the purposes of backup and parallel tunnels.
HP-SN-MPLS-TC-MIBMplsTunnelInstanceIndex
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.2
mplsTunnelIngressLSRId
The purpose of this object is to uniquely identity a
tunnel within a network. When the MPLS signalling
protoocol is rsvp(2) this value SHOULD mimic the
Extended Tunnel Id field in the SESSION object.
When the MPLS signa…
HP-SN-MPLS-TC-MIBMplsLsrIdentifier
Type Constraints:
range: 4
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.3
mplsTunnelEgressLSRId
Specifies the egress LSR ID.
HP-SN-MPLS-TC-MIBMplsLsrIdentifier
Type Constraints:
range: 4
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.4
mplsTunnelName
The canonical name assigned to the tunnel. This name
can be used to refer to the tunnel on the LSR's
console port. If mplsTunnelIsIf is set to true
then the ifName of the interface corresponding to
this tunnel should h…
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.5
mplsTunnelDescr
A textual string containing information about the
tunnel. If there is no description this object
contains a zero length string.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.6
mplsTunnelIsIf
Denotes whether or not this tunnel corresponds to an
interface represented in the interfaces group
table. Note that if this variable is set to true
then the ifName of the interface corresponding to
this tunnel should ha…
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.7
mplsTunnelIfIndex
If mplsTunnelIsIf is set to true, then this value
contains the LSR-assigned ifIndex which corresponds
to an entry in the interfaces table. Otherwise
this variable should contain the value of zero
indicating that a vali…
IF-MIBInterfaceIndexOrZero
Type Constraints:
range: 0..2147483647
Description:
This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.8
mplsTunnelXCPointer
This variable points to a row in the mplsXCTable.
This table identifies the segments that compose
this tunnel, their characteristics, and
relationships to each other. A value of zeroDotZero
indicates that no LSP has bee…
SNMPv2-TCRowPointerr/w
Description:
Represents a pointer to a conceptual row. The value is the
name of the instance of the first accessible columnar object
in the conceptual row.

For example, ifIndex.3 would point to the 3rd row in the
ifTable…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.9
mplsTunnelSignallingProto
The signaling protocol, if any, which was used to
setup this tunnel.
Enumerationr/w
Enumerated Values:
1none
2rsvp
3crldp
4other
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.10
mplsTunnelSetupPrio
Indicates the setup priority of this tunnel.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.11
mplsTunnelHoldingPrio
Indicates the holding priority for this tunnel.
Integer32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.12
mplsTunnelSessionAttributes
This bitmask indicates optional session values for
this tunnel. The following describes these
bitfields:

fastRerouteThis flag indicates that the any tunnel
hop may choose to reroute this tunnel without
te…
Bitsr/w
Enumerated Values:
0fastReroute
1mergingPermitted
2isPersistent
3isPinned
4recordRoute
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.13
mplsTunnelOwner
Indicates which protocol created and is responsible
for managing this tunnel. Values rsvp(2) and
crldp(3) should not be used at the head-end of a
MPLS tunnel.
Enumerationr/w
Enumerated Values:
1admin
2rsvp
3crldp
4policyAgent
5other
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.14
mplsTunnelLocalProtectInUse
Indicates that the local repair mechanism is in use
to maintain this tunnel (usually in the face of an
outage of the link it was previously routed over).
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.15
mplsTunnelResourcePointer
This variable represents a pointer to the traffic
parameter specification for this tunnel. This
value may point at an entry in the
mplsTunnelResourceEntry to indicate which
mplsTunnelResourceEntry is to be assigned to …
SNMPv2-TCRowPointerr/w
Description:
Represents a pointer to a conceptual row. The value is the
name of the instance of the first accessible columnar object
in the conceptual row.

For example, ifIndex.3 would point to the 3rd row in the
ifTable…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.16
mplsTunnelInstancePriority
This value indicates which priority, in descending
order, with 0 indicating the lowest priority,
within a group of tunnel instances. A group of
tunnel instances is defined as a set of tunnels
with the same mplsTunnelInd…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.17
mplsTunnelHopTableIndex
Index into the mplsTunnelHopTable entry that
specifies the explicit route hops for this tunnel.
HP-SN-MPLS-TC-MIBMplsPathIndexOrZeror/w .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.18
mplsTunnelARHopTableIndex
Index into the mplsTunnelARHopTable entry that
specifies the actual hops traversed by the tunnel.
HP-SN-MPLS-TC-MIBMplsPathIndexOrZero .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.19
mplsTunnelCHopTableIndex
Index into the mplsTunnelCHopTable entry that
specifies the computed hops traversed by the
tunnel.
HP-SN-MPLS-TC-MIBMplsPathIndexOrZero .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.20
mplsTunnelPrimaryInstance
Specifies the instance index of the primary instance
of this tunnel.
HP-SN-MPLS-TC-MIBMplsTunnelInstanceIndex
Type Constraints:
range: 0..65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.21
mplsTunnelPrimaryTimeUp
Specifies the total time the primary instance of
this tunnel has been active. The primary instance
of this tunnel is defined in
mplsTunnelPrimaryInstance.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.22
mplsTunnelPathChanges
Specifies the number of times the paths has changed
for this tunnel.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.23
mplsTunnelLastPathChange
Specifies the time since the last path change for
this tunnel.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.24
mplsTunnelCreationTime
Specifies the value of SysUpTime when the first
instance of this tunnel came into existence.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.25
mplsTunnelStateTransitions
Specifies the number of times the state of this
tunnel instance has changed.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.26
mplsTunnelIncludeAnyAffinity
A link satisfies the include-any constraint if and
only if the constraint is zero, or the link and the
constraint have a resource class in common.
HP-SN-MPLS-TC-MIBMplsTunnelAffinityr/w .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.27
mplsTunnelIncludeAllAffinity
A link satisfies the include-all constraint if and
only if the link contains all of the adminstrative
groups specified in the constraint.
HP-SN-MPLS-TC-MIBMplsTunnelAffinityr/w .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.28
mplsTunnelExcludeAllAffinity
A link satisfies the exclude-all constraint if and
only if the link contains none of the adminstrative
groups specifie in the constraint.
HP-SN-MPLS-TC-MIBMplsTunnelAffinityr/w .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.29
mplsTunnelPathInUse
This value denotes the configured path that was
chosen for this tunnel. This value reflects the
secondary index into mplsTunnelHopTable. This path
may not exactly match the one in
mplsTunnelARHopTable due to the fact th…
HP-SN-MPLS-TC-MIBMplsPathIndexOrZeror/w .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.30
mplsTunnelRole
This value signifies the role that this tunnel
entry/instance represents. This value MUST be set
to head(1) at the originating point of the tunnel.
This value MUST be set to transit(2) at transit
points along the tunnel…
Enumerationr/w
Enumerated Values:
1head
2transit
3tail
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.31
mplsTunnelTotalUpTime
This value represents the aggregate up time for all
instances of this tunnel, if available. If this
value is unavailable, it MUST return a value of 0.
SNMPv2-SMITimeTicksr/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.32
mplsTunnelInstanceUpTime
This value identifies the total time that this
tunnel instance's operStatus has been Up(1).
SNMPv2-SMITimeTicksr/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.33
mplsTunnelAdminStatus
Indicates the desired operational status of this
tunnel.
Enumerationr/w
Enumerated Values:
1up
2down
3testing
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.34
mplsTunnelOperStatus
Indicates the actual operational status of this
tunnel, which is typically but not limited to, a
function of the state of individual segments of
this tunnel.
Enumeration
Enumerated Values:
1up
2down
3testing
4unknown
5dormant
6notPresent
7lowerLayerDown
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.35
mplsTunnelRowStatus
This variable is used to create, modify, and/or
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.36
mplsTunnelStorageType
This variable indicates the storage type for this
object.
SNMPv2-TCStorageTyper/w
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
Description:
Describes the memory realization of a conceptual row. A
row which is volatile(2) is lost upon reboot. A row which
is either nonVolatile(3), permanent(4) or readOnly(5), is
backed up by stable storage. A row which is …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.2.1.37

mplsTunnelHopTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4 · 1 row entry · 16 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelHopTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelHopTable' 
The mplsTunnelHopTable is used to indicate the hops,
strict or loose, for an MPLS tunnel defined in
mplsTunnelTable, when it is established via
signaling, for the outgoing direction of the
tunnel.  Each row in this table is indexed by
mplsTunnelHopListIndex.  Each row also has a
secondary index mplsTunnelHopIndex corresponding to
the next hop that this row corresponds to.  The
first row in the table is the first hop after the
origination point of the tunnel.  In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelHopTable.
mplsTunnelHopEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1
An entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol.
Indexes
Column Syntax OID
mplsTunnelHopListIndex
Primary index into this table identifying a
particular explicit route object.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.1
mplsTunnelHopPathOptionIndex
Secondary index into this table identifying a
particular group of hops representing a particular
configured path. This is otherwise known as a path
option.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.2
mplsTunnelHopIndex
Secondary index into this table identifying a
particular hop.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.3
mplsTunnelHopAddrType
Denotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP.
Enumerationr/w
Enumerated Values:
1ipV4
2ipV6
3asNumber
4lspid
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.4
mplsTunnelHopIpv4Addr
If mplsTunnelHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this

hop. If mplsTunnelHopAddrType is set to lspid(4),
then this value will contain the Ingress LSR Router
ID o…
INET-ADDRESS-MIBInetAddressIPv4r/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.5
mplsTunnelHopIpv4PrefixLen
If mplsTunnelHopAddrType is ipV4(1), then the prefix
length for this hop's IPv4 address is contained
herein. This object is otherwise insignificant and
should contain a value of 0.
Unsigned32r/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.6
mplsTunnelHopIpv6Addr
If the mplsTunnelHopAddrType is set to ipV6(2), then
this variable contains the IPv6 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.
INET-ADDRESS-MIBInetAddressIPv6r/w
Type Constraints:
range: 16
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.7
mplsTunnelHopIpv6PrefixLen
If mplsTunnelHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.
Unsigned32r/w
Constraints:
range: 0-128
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.8
mplsTunnelHopAsNumber
If mplsTunnelHopAddrType is set to asNumber(3), then
this value will contain the AS number of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.
Unsigned32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.9
mplsTunnelHopLspId
If mplsTunnelHopAddrType is set to lspid(4), then
this value will contain the LSPID of a tunnel of
this hop. The present tunnel being configured is
tunneled through this hop (using label stacking).
This object is otherw…
HP-SN-MPLS-TC-MIBMplsLSPIDr/w
Type Constraints:
range: 0..31
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.10
mplsTunnelHopType
Denotes whether this tunnel hop is routed in a
strict or loose fashion.
Enumerationr/w
Enumerated Values:
1strict
2loose
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.11
mplsTunnelHopIncludeExclude
If this value is set to include(1), then this
indicates that this hop must be included in the
tunnel's path. If this value is set to exclude(2),
then this hop must be avoided when calculating the
path for this tunnel. T…
Enumerationr/w
Enumerated Values:
1include
2exclude
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.12
mplsTunnelHopPathOptionName
The description of this series of hops as they
relate to the specified path option.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.13
mplsTunnelHopEntryPathComp
If this value is set to dynamic, then the user
should only specify the source and destination of
the path and expect that the CSPF will calculate
the remainder of the path. If this value is set to
explicit, the user sh…
Enumerationr/w
Enumerated Values:
1dynamic
2explicit
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.14
mplsTunnelHopRowStatus
This variable is used to create, modify, and/or
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.15
mplsTunnelHopStorageType
This variable indicates the storage type for this
object.
SNMPv2-TCStorageTyper/w
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
Description:
Describes the memory realization of a conceptual row. A
row which is volatile(2) is lost upon reboot. A row which
is either nonVolatile(3), permanent(4) or readOnly(5), is
backed up by stable storage. A row which is …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.4.1.16

mplsTunnelResourceTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6 · 1 row entry · 10 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelResourceTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelResourceTable' 
The mplsTunnelResourceTable allows a manager to
specify which resources are desired for an MPLS
tunnel.  This table also allows several tunnels to
point to a single entry in this table, implying
that these tunnels should share resources.
mplsTunnelResourceEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1
An entry in this table represents a set of resources
for an MPLS tunnel. An entry can be created by a
network administrator or by an SNMP agent as
instructed by any MPLS signaling protocol.
Indexes
Column Syntax OID
mplsTunnelResourceIndex
Uniquely identifies this row.
Unsigned32
Constraints:
range: 1-2147483647
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.1
mplsTunnelResourceMaxRate
The maximum rate in bits/second. Note that setting
mplsTunnelResourceMaxRate,
mplsTunnelResourceMeanRate, and
mplsTunnelResourceMaxBurstSize to 0 indicates best-
effort treatment.
This object is copied to an instance o…
bits per secondHP-SN-MPLS-TC-MIBMplsBitRater/w
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.2
mplsTunnelResourceMeanRate
This object is copied into an instance of
mplsTrafficParamMeanRate in the
mplsTrafficParamTable. The OID of this table entry
is then copied into the corresponding
mplsInSegmentTrafficParamPtr.

When resour…
bits per secondHP-SN-MPLS-TC-MIBMplsBitRater/w
Type Constraints:
range: 1..2147483647
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.3
mplsTunnelResourceMaxBurstSize
The maximum burst size in bytes. This object is
copied to mplsInSegmentMaxBurstSize of the
corresponding in-segment.

When resource allocation is performed as requested
by this TSpec object, it is copied …
bytesHP-SN-MPLS-TC-MIBMplsBurstSizer/w
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.4
mplsTunnelResourceMeanBurstSize
The mean burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value.
bytesHP-SN-MPLS-TC-MIBMplsBurstSizer/w
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.5
mplsTunnelResourceExcessBurstSize
The Excess burst size in bytes. The implementations
which do not implement this variable must return 0
for this value and must not allow a user to set
this value.
bytesHP-SN-MPLS-TC-MIBMplsBurstSizer/w
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.6
mplsTunnelResourceFrequency
The granularity of the availability of committed
rate. The implementations which do not implement
this variable must return unspecified(1) for this
value and must not allow a user to set this value.
Enumerationr/w
Enumerated Values:
1unspecified
2frequent
3veryFrequent
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.7
mplsTunnelResourceWeight
The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP.
Unsigned32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.8
mplsTunnelResourceRowStatus
This variable is used to create, modify, and/or
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.9
mplsTunnelResourceStorageType
This variable indicates the storage type for this
object.
SNMPv2-TCStorageTyper/w
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
Description:
Describes the memory realization of a conceptual row. A
row which is volatile(2) is lost upon reboot. A row which
is either nonVolatile(3), permanent(4) or readOnly(5), is
backed up by stable storage. A row which is …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.6.1.10

mplsTunnelARHopTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7 · 1 row entry · 9 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelARHopTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelARHopTable' 
The mplsTunnelARHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as reported by the MPLS
signaling protocol, for the outgoing direction of
the tunnel.  Each row in this table is indexed by
mplsTunnelARHopListIndex.  Each row also has a
secondary index mplsTunnelARHopIndex, corresponding
to the next hop that this row corresponds to.  The
first row in the table is the first hop after the
origination point of the tunnel.  In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelARHopTable.
          
Please note that since the information necessary to
build entries within this table are not provided by
some MPLS signaling protocols, implementation of
this table is optional. Furthermore, since the
information in this table is actually provided by
the MPLS signaling protocol after the path has been
set-up, the entries in this table are provided only
for observation, and hence, all variables in this
table are accessible exclusively as read-only.
mplsTunnelARHopEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1
An entry in this table represents a tunnel hop. An
entry is created by a network administrator for
signaled ERLSP set up by an MPLS signaling
protocol.
Indexes
Column Syntax OID
mplsTunnelARHopListIndex
Primary index into this table identifying a
particular recorded hop list.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.1
mplsTunnelARHopIndex
Secondary index into this table identifying the
particular hop.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.2
mplsTunnelARHopAddrType
Denotes the address type of this tunnel hop.
Enumeration
Enumerated Values:
1ipV4
2ipV6
3asNumber
4lspId
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.3
mplsTunnelARHopIpv4Addr
If mplsTunnelARHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.
INET-ADDRESS-MIBInetAddressIPv4
Type Constraints:
range: 4
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.4
mplsTunnelARHopIpv4PrefixLen
If mplsTunnelARHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.
Unsigned32
Constraints:
range: 0-32
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.5
mplsTunnelARHopIpv6Addr
If the mplsTunnelARHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.
INET-ADDRESS-MIBInetAddressIPv6
Type Constraints:
range: 16
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.6
mplsTunnelARHopIpv6PrefixLen
If mplsTunnelARHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.
Unsigned32
Constraints:
range: 0-128
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.7
mplsTunnelARHopAsNumber
If mplsTunnelARHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact.
Unsigned32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.8
mplsTunnelARHopLspId
If mplsTunnelARHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.
HP-SN-MPLS-TC-MIBMplsLSPID
Type Constraints:
range: 0..31
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.7.1.9

mplsTunnelCHopTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8 · 1 row entry · 10 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelCHopTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelCHopTable' 
The mplsTunnelCHopTable is used to indicate the
hops, strict or loose, for an MPLS tunnel defined
in mplsTunnelTable, as computed by a constraint-
based routing protocol, based on the
mplsTunnelHopTable for the outgoing direction of
the tunnel.  Each row in this table is indexed by
mplsTunnelCHopListIndex.  Each row also has a
secondary index mplsTunnelCHopIndex, corresponding
to the next hop that this row corresponds to.  The
first row in the table is the first hop after the
origination point of the tunnel.  In case we want
to specify a particular interface on the
originating LSR of an outgoing tunnel by which we
want packets to exit the LSR, we specify this as
the first hop for this tunnel in
mplsTunnelCHopTable.
          
Please note that since the information necessary to
build entries within this table may not be
supported by some LSRs, implementation of this
table is optional. Furthermore, since the
information in this table is actually provided by
routing protocol after the path has been computed,
the entries in this table are provided only for
observation, and hence, all variables in this table
are accessible exclusively as read-only.
mplsTunnelCHopEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1
An entry in this table represents a tunnel hop. An
entry in this table is created by a constraint-
based routing protocol based on the hops specified
in the corresponding mplsTunnelHopTable.
Indexes
Column Syntax OID
mplsTunnelCHopListIndex
Primary index into this table identifying a
particular computed hop list.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.1
mplsTunnelCHopIndex
Secondary index into this table identifying the
particular hop.
HP-SN-MPLS-TC-MIBMplsPathIndex .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.2
mplsTunnelCHopAddrType
Denotes the address type of this tunnel hop. Note
that lspId(4) is a valid option only for tunnels
signaled via CRLDP.
Enumeration
Enumerated Values:
1ipV4
2ipV6
3asNumber
4lspId
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.3
mplsTunnelCHopIpv4Addr
If mplsTunnelCHopAddrType is set to ipV4(1), then
this value will contain the IPv4 address of this
hop. This object is otherwise insignificant and
should contain a value of 0.
INET-ADDRESS-MIBInetAddressIPv4
Type Constraints:
range: 4
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.4
mplsTunnelCHopIpv4PrefixLen
If mplsTunnelCHopAddrType is ipV4(1), then the
prefix length for this hop's IPv4 address is
contained herein. This object is otherwise
insignificant and should contain a value of 0.
Unsigned32
Constraints:
range: 0-32
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.5
mplsTunnelCHopIpv6Addr
If the mplsTunnelCHopAddrType is set to ipV6(2),
then this variable contains the IPv6 address of
this hop. This object is otherwise insignificant
and should contain a value of 0.
INET-ADDRESS-MIBInetAddressIPv6
Type Constraints:
range: 16
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.6
mplsTunnelCHopIpv6PrefixLen
If mplsTunnelCHopAddrType is set to ipV6(2), this
value will contain the prefix length for this hop's
IPv6 address. This object is otherwise
insignificant and should contain a value of 0.
Unsigned32
Constraints:
range: 0-128
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.7
mplsTunnelCHopAsNumber
If mplsTunnelCHopAddrType is set to asNumber(3),
then this value will contain the AS number of this
hop. This object is otherwise insignificant and
should contain a value of 0 to indicate this fact.
Unsigned32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.8
mplsTunnelCHopLspId
If mplsTunnelCHopAddrType is set to lspid(4), then
this value will contain the LSP ID of this hop.
This object is otherwise insignificant and should
contain a value of 0 to indicate this fact.
HP-SN-MPLS-TC-MIBMplsLSPID
Type Constraints:
range: 0..31
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.9
mplsTunnelCHopType
Denotes whether this is tunnel hop is routed in a
strict or loose fashion.
Enumeration
Enumerated Values:
1strict
2loose
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.8.1.10

mplsTunnelPerfTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9 · 1 row entry · 5 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelPerfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelPerfTable' 
This table provides per-tunnel MPLS performance
information.
mplsTunnelPerfEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1
An entry in this table is created by the LSR for
every tunnel. Its is an extension to
mplsTunnelEntry.
Indexes
No indexes recorded
Column Syntax OID
mplsTunnelPerfPackets
Number of packets forwarded by the tunnel.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.1
mplsTunnelPerfHCPackets
High capacity counter for number of packets
forwarded by the tunnel.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.2
mplsTunnelPerfErrors
Number of errored packets.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.3
mplsTunnelPerfBytes
Number of bytes forwarded by the tunnel.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.4
mplsTunnelPerfHCBytes
High capacity counter for number of bytes forwarded
by the tunnel.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.9.1.5

mplsTunnelCRLDPResTable

table
.1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10 · 1 row entry · 7 columns
Open in standard view
Uses the hp variant from /opt/observium/mibs/hp.
Command help
Walk mplsTunnelCRLDPResTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HP-SN-MPLS-TE-MIB' -M '/opt/observium/mibs/hp:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HP-SN-MPLS-TE-MIB::mplsTunnelCRLDPResTable' 
The mplsTunnelCRLDPResTable allows a manager to
specify which CR-LDP-specific resources are desired
for an MPLS tunnel if that tunnel is signaled using
CR-LDP. Note that these attributes are in addition
to those specified in mplsTunnelResourceTable. This
table also allows several tunnels to point to a
single entry in this table, implying that these
tunnels should share resources.
mplsTunnelCRLDPResEntry row .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1
An entry in this table represents a set of resources
for an MPLS tunnel established using CRLDP
(mplsTunnelSignallingProto equal to crldp (3)). An
entry can be created by a network administrator or
by an SNMP agent as i…
Indexes
Column Syntax OID
mplsTunnelCRLDPResMeanBurstSize
The mean burst size in bytes.
bytesHP-SN-MPLS-TC-MIBMplsBurstSizer/w
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.2
mplsTunnelCRLDPResExcessBurstSize
The Excess burst size in bytes.
bytesHP-SN-MPLS-TC-MIBMplsBurstSizer/w
Type Constraints:
range: 1..4294967295
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.3
mplsTunnelCRLDPResFrequency
The granularity of the availability of committed
rate.
Enumerationr/w
Enumerated Values:
1unspecified
2frequent
3veryFrequent
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.4
mplsTunnelCRLDPResWeight
The relative weight for using excess bandwidth above
its committed rate. The value of 0 means that
weight is not applicable for the CR-LSP.
Unsigned32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.5
mplsTunnelCRLDPResFlags
The value of the 1 byte Flags conveyed as part of
the traffic parameters during the establishment of
the CRLSP. The bits in this object are to be
interpreted as follows.

+--+--+--+--+--+--+--+--+
| Res |F…
Unsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.6
mplsTunnelCRLDPResRowStatus
This variable is used to create, modify, and/or
delete a row in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.7
mplsTunnelCRLDPResStorageType
This variable indicates the storage type for this
object.
SNMPv2-TCStorageTyper/w
Type Values:
1other
2volatile
3nonVolatile
4permanent
5readOnly
Description:
Describes the memory realization of a conceptual row. A
row which is volatile(2) is lost upon reboot. A row which
is either nonVolatile(3), permanent(4) or readOnly(5), is
backed up by stable storage. A row which is …
 .1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.3.2.10.1.8