HP-PROCURVE-420-PRIVATE-MIB Table View

Table of descriptive and status information about
configuration of each RS-232 line in this system

lineEntry row .1.3.6.1.4.1.11.2.3.7.11.37.2.1.1

An entry in the table, containing information
about configuration in one RS232 line of the Access Point.

Indexes

lineIndex

Column	Syntax	OID
lineIndexmandatory This is defined as RS-232 index.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.1
lineDataBitsmandatory This is defined as number of data bits for the RS232 interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.2
lineParitymandatory This is defined as parity of the RS232 interface.	Enumeration Enumerated Values: 1 odd 2 even 99 none	.1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.3
lineSpeedmandatory This is defined as the speed of the RS-232 interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.4
lineStopBitsmandatory This is defined as the number of stop bits for the RS-232 interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.2.1.1.5

Table of descriptive and status information about
configuration of each switch port (including expansion slot)
in this system. This table also contains information
about each trunk (similar to Cisco's EtherChannel).

portEntry row .1.3.6.1.4.1.11.2.3.7.11.37.3.1.1

An entry in the table, containing information
about configuration in one switch port of the switch.

Indexes

portIndex

Column	Syntax	OID
portIndexmandatory This is defined as ifIndex in the IF-MIB.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.1
portNamemandatory Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.2
portTypemandatory Indicates the port type.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseMiniGBIC	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.3
portSpeedDpxCfgmandatory Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100…	Enumeration Enumerated Values: 1 auto 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.4
portFlowCtrlCfgmandatory (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in…	Enumeration Enumerated Values: 1 enabled 2 disabled 3 backPressure 4 dot3xFlowControl	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.5
portCapabilitiesmandatory Port capabilities.	Enumeration Enumerated Values: 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 reserved6 7 reserved7 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl 99 portCap10half	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.6
portAutonegotiationmandatory Whether autonegotiation is enabled.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.7
portSpeedDpxStatusmandatory The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this …	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.8
portFlowCtrlStatusmandatory (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, thi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.11.2.3.7.11.37.3.1.1.9

Table of descriptive and status information about
configuration of each radio of the AP.

hpdot11StationConfigEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.1.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11portIndex

Column	Syntax	OID
hpdot11portIndexmandatory Radio index of the AP.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.1
hpdot11DesiredSSIDmandatory This attribute reflects the Service Set ID used in the DesiredSSID parameter of the most recent MLME_Scan.request. This value may be modified by an external management entity and used by the local SME to make decisions …	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.2
hpdot11BeaconPeriodmandatory This attribute shall specify the number of ms that a station shall use for scheduling Beacon transmissions. This value is transmitted in Beacon and Probe Response frames.	Integer32r/w Constraints: range: 20-1000	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.3
hpdot11DTIMPeriodmandatory This attribute shall specify the number of beacon intervals that shall elapse between transmission of Beacons frames containing a TIM element whose DTIM Count field is 0. This value is transmitted in the DTIM Period fie…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.4
hpdot11OperationalRateSetmandatory This attribute shall specify the set of data rates at which the station may transmit data. Each octet contains a value representing a rate. Each rate shall be within the range from 2 to 127, corresponding to data rates …	Integer32r/w Constraints: range: 1-108	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.5
hpdot11AuthenticationAlgorithmmandatory This attribute shall be a set of all the authentication algorithms supported by the STAs. The following are the default values and the associated algorithm. Value = 1: Open System Value = 2: Shared Key	Enumerationr/w Enumerated Values: 1 openSystem 2 sharedKey	.1.3.6.1.4.1.11.2.3.7.11.37.7.1.1.6

Table of descriptive and status information about
configuration of each radio of the AP.

hpdot11PrivacyEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.2.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11PrivacyportIndex

Column	Syntax	OID
hpdot11PrivacyportIndexmandatory Radio index of the AP.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.1
hpdot11PrivacyInvokedmandatory When this attribute is true, it shall indicate that the IEEE 802.11 WEP mechanism is used for transmitting frames of type Data. The default value of this attribute shall be false.	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.2
hpdot11WEPDefaultKeyIDmandatory This attribute shall indicate the use of the first, second, or third element of the WEPDefaultKeys array when set to values of zero, one, or two(the fourth are reserved for dynamic key). The default value of this attri…	Integer32r/w Constraints: range: 0-3	.1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.3
hpdot11WEPKeyMappingLengthmandatory The maximum number of tuples that dot11WEPKeyMappings can hold.	Integer32r/w Constraints: range: 10-2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.2.1.4

Table of descriptive and status information about
configuration of each radio of the AP.

hpdot11OperationEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11OperationIndex

Column	Syntax	OID
hpdot11OperationIndexmandatory Radio index of the AP.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.1
hpdot11RTSThresholdmandatory This attribute shall indicate the number of octets in an MPDU, below which an RTS/CTS handshake shall not be performed. An RTS/CTS handshake shall be performed at the beginning of any frame exchange sequence where the M…	Integer32r/w Constraints: range: 0-2347	.1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.2
hpdot11FragmentationThresholdmandatory This attribute shall specify the mandatory maximum size, in octets, of the MPDU that may be delivered to the PHY. An MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC h…	Integer32r/w Constraints: range: 256-2346	.1.3.6.1.4.1.11.2.3.7.11.37.7.3.1.1.3

Table of descriptive and status information about
configuration of each radio of the AP.

hpdot11PhyOperationEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11Index

Column	Syntax	OID
hpdot11Indexmandatory Radio index of the AP.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.1
hpdot11CurrentChannelmandatory The current operating frequency channel of the network	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.2
hpdot11TurboModeEnabledmandatory This attribute, when true, shall indicate that the propietory turbo mode option is enabled. The default value of this attribute shall be false.	Enumeration Enumerated Values: 1 on 2 off 99 none	.1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.3
hpdot11PreambleLengthmandatory This attribute determines whether or not a short or a long preamble is used to delineate 802.11 frames.	Enumerationr/w Enumerated Values: 1 short 2 long	.1.3.6.1.4.1.11.2.3.7.11.37.7.4.1.1.4

Table of descriptive and status information about
configuration of each authentication server.

hpdot11AuthenticationServerEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.6.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11serverIndex

Column	Syntax	OID
hpdot11serverIndexmandatory Radio index of the AP.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.1
hpdot11AuthenticationServermandatory This values indicates the IP address of the authentication server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.2
hpdot11AuthenticationPortmandatory This values indicates the UDP Port used by the primary authentication server.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.3
hpdot11AuthenticationKeymandatory This values indicates the shared key used by the authentication server.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.4
hpdot11AuthenticationRetransmitmandatory This values indicates the retransmit timer length used by the authentication server.	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.5
hpdot11AuthenticationTimeoutmandatory This values indicates the Timeout value(sec) used by the authentication server.	Integer32r/w Constraints: range: 1-60	.1.3.6.1.4.1.11.2.3.7.11.37.7.6.1.6

Table of status information about
each configured MAC Address Filtering Entry.

hpdot11FilterEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.7.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

hpdot11FilterIndex

Column	Syntax	OID
hpdot11FilterIndexmandatory Filter index.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.1
hpdot11FilterAddressmandatory This values indicates the MAC address of the filter entry.	PhysAddressr/w	.1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.2
hpdot11FilterStatusmandatory This values indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.	Enumerationr/w Enumerated Values: 30 allowed 31 denied	.1.3.6.1.4.1.11.2.3.7.11.37.7.7.1.3

Conceptual table for WEP default keys.  This table shall
contain the four WEP default secret key values
corresponding to the four possible KeyID values.  The WEP
default secret keys are logically WRITE-ONLY.  Attempts to
read the entries in this table shall return unsuccessful
status and values of null or zero.  The default value of
each WEP default key shall be null.

hpdot11WEPDefaultKeys11gEntry row .1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1

An Entry (conceptual row) in the WEP Default Keys Table.

ifIndex - Each 802.11 interface is represented by an
ifEntry. Interface tables in this MIB module are indexed
by ifIndex.

Indexes

dot11WEPDefaultKey11gLength

Column	Syntax	OID
hpdot11WEPDefaultKey11gLengthmandatory A 40(64)-bits [5 octets WEP], 104(128)-bits [13 octets] or 128(152)-bits [16 octets]	Enumerationr/w Enumerated Values: 64 sixtyFour 128 oneHundredTwentyEight 152 oneHundredFiftyTwo	.1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.1
hpdot11WEPDefaultKey11gIndexmandatory The auxiliary variable used to identify instances of the columnar objects in the WEP Default Keys Table. The value of this variable is equal to the WEPDefaultKeyID + 1	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.2
hpdot11WEPDefaultKey11gValuemandatory A 40(64)-bits [5 octets WEP] or 104(128)-bits [13 octets] default secret key value.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.11.2.3.7.11.37.7.8.1.1.1.3