HM2-PLATFORM-ROUTING-MIB Table View

This table contains the per-interface configuration
parameters for local proxy ARP.

hm2AgentSwitchLocalProxyArpEntry row .1.3.6.1.4.1.248.12.2.1.11.1

Represents a logical row in the
hm2AgentSwitchLocalProxyArpTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hm2AgentSwitchLocalProxyArpMode The local proxy ARP mode for the interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.1.11.1.1

This table augments the MIB-II ipNetToMediaTable by providing
per-interface ARP entry information.

hm2AgentSwitchIntfArpEntry row .1.3.6.1.4.1.248.12.2.1.12.1

This table augments the MIB-II ipNetToMediaTable by providing
per-interface ARP entry information.

Indexes

hm2AgentSwitchIntfArpIpAddress hm2AgentSwitchIntfArpIfIndex

Column	Syntax	OID
hm2AgentSwitchIntfArpIpAddress The Type of Address assigned to this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.1.12.1.1
hm2AgentSwitchIntfArpIfIndex The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.248.12.2.1.12.1.2
hm2AgentSwitchIntfArpAge This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.1.12.1.3
hm2AgentSwitchIntfArpMacAddress The hardware MAX Address that each interface maps to.	RFC1213-MIBPhysAddressr/w	.1.3.6.1.4.1.248.12.2.1.12.1.4
hm2AgentSwitchIntfArpType The type of ARP entry.	Enumeration Enumerated Values: 1 local 2 gateway 3 static 4 dynamic	.1.3.6.1.4.1.248.12.2.1.12.1.5
hm2AgentSwitchIntfArpStatus The status of this ARP entry. Setting this object destroy will remove the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.1.12.1.6

IP interface table.

hm2AgentSwitchIpInterfaceEntry row .1.3.6.1.4.1.248.12.2.2.3.1

IP interface entry.

Indexes

hm2AgentSwitchIpInterfaceIfIndex

Column	Syntax	OID
hm2AgentSwitchIpInterfaceIfIndex The IfIndex associated with this instance.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.248.12.2.2.3.1.1
hm2AgentSwitchIPAddressConfigMethod The source of the IP address. User can set the object to none(0) or dhcp(2). Option dhcp(2) enables DHCP client on the interface. Option none(0) disables DHCP client on the interface. Get on this object returns manual(1…	Enumerationr/w Enumerated Values: 0 none 1 manual 2 dhcp	.1.3.6.1.4.1.248.12.2.2.3.1.2
hm2AgentSwitchIpInterfaceIpAddress The IP address assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceNetMask must be set at the same time.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.3.1.3
hm2AgentSwitchIpInterfaceNetMask The netmask assigned to this interface. When setting this value, the value of hm2AgentSwitchIpInterfaceIpAddress must be set at the same time.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.3.1.4
hm2AgentSwitchIpInterfaceClearIp When setting this object to 'enable(1)' the interfaces IP address and netmask will be set back to 0.0.0.0. Reading this object always returns 'disable(2).	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.5
hm2AgentSwitchIpInterfaceRoutingMode Enables or disables routing for this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.6
hm2AgentSwitchIpInterfaceProxyARPMode Enables or disables proxy ARP for this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.7
hm2AgentSwitchIpInterfaceMtuValue Configures the MTU value for this interface. The applicable range is 68 to the <interface MTU value - 18>, in bytes. Get of this object returns the effective MTU value on the interface. Set of this object with a valu…	Unsigned32r/w Constraints: range: 0-0 range: 68-12266	.1.3.6.1.4.1.248.12.2.2.3.1.8
hm2AgentSwitchIpInterfaceBandwidth Configures the bandwidth value for this interface. If the returned value is 0, bandwidth for this interface is not configured.	Unsigned32r/w Constraints: range: 0-10000000	.1.3.6.1.4.1.248.12.2.2.3.1.9
hm2AgentSwitchIpInterfaceUnnumberedIfIndex If this object is non-zero, it indicates that the interface is unnumbered and specifies which interface the address is borrowed from.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.248.12.2.2.3.1.10
hm2AgentSwitchIpInterfaceIcmpUnreachables If this object is enabled, it indicates that ICMP unreachables can be sent on this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.11
hm2AgentSwitchIpInterfaceIcmpRedirects If this object is enabled and hm2AgentSwitchIpIcmpRedirectsMode is also enabled, ICMP redirects can be sent on this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.12
hm2AgentSwitchDhcpOperation Renew or release the IP address learned through DHCP. Get on this object always gives none. None means no operation is performed on DHCP.	Enumerationr/w Enumerated Values: 1 renew 2 release 3 none	.1.3.6.1.4.1.248.12.2.2.3.1.13
hm2AgentSwitchIpInterfaceSuppressed This mib variable contains the following values, which has the meaning as: 'unsuppressed' - The interface is not suppressed 'suppressed' - The interface is suppressed	Enumeration Enumerated Values: 0 unsuppressed 1 suppressed	.1.3.6.1.4.1.248.12.2.2.3.1.14
hm2AgentSwitchIpInterfaceNumberOfFlaps This mib variable displays the number of flaps occurred on the interface	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.4.1.248.12.2.2.3.1.15
hm2AgentSwitchIpInterfaceCurrentPenalty This mib variable displays the current penalty of an interface	Unsigned32 Constraints: range: 0-20000	.1.3.6.1.4.1.248.12.2.2.3.1.16
hm2AgentSwitchIpInterfaceReUseTime This mib variable displays the number of seconds until the interface is allowed to come up	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.2.3.1.17
hm2AgentSwitchIpInterfaceNetdirectedBCMode Enables or disables netdirected broadcasts for this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.3.1.248

There is no global administrative flag for router discovery.  The global
routing flag (hm2AgentSwitchIpRoutingMode) will be used for this purpose.  If routing
is disabled, router discovery is disabled as well.

hm2AgentSwitchIpRouterDiscoveryEntry row .1.3.6.1.4.1.248.12.2.2.4.1

.

Indexes

hm2AgentSwitchIpRouterDiscoveryIfIndex

Column	Syntax	OID
hm2AgentSwitchIpRouterDiscoveryIfIndex Interface Number to configure Router Discovery on.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.248.12.2.2.4.1.1
hm2AgentSwitchIpRouterDiscoveryAdvertiseMode Enable or disable router discovery on the interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.2.4.1.2
hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval Maximum time allowed between sending router advertisements from the interface.	Integer32r/w Constraints: range: 4-1800	.1.3.6.1.4.1.248.12.2.2.4.1.3
hm2AgentSwitchIpRouterDiscoveryMinAdvertisementInterval Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.	Integer32r/w Constraints: range: 3-1800	.1.3.6.1.4.1.248.12.2.2.4.1.4
hm2AgentSwitchIpRouterDiscoveryAdvertisementLifetime Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to hm2AgentSwitchIpRouterDiscoveryMaxAdvertisementInterval.	Integer32r/w Constraints: range: 4-9000	.1.3.6.1.4.1.248.12.2.2.4.1.5
hm2AgentSwitchIpRouterDiscoveryPreferenceLevel Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.2.4.1.6
hm2AgentSwitchIpRouterDiscoveryAdvertisementAddress Address used when sending router advertisements from the interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.4.1.7

A static VLAN for which routing can be enabled/disabled.

hm2AgentSwitchIpVlanEntry row .1.3.6.1.4.1.248.12.2.2.5.1

A static VLAN for which routing can be enabled/disabled.

Indexes

hm2AgentSwitchIpVlanId

Column	Syntax	OID
hm2AgentSwitchIpVlanId The VLAN's ID.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.248.12.2.2.5.1.1
hm2AgentSwitchIpVlanIfIndex The IfIndex associated with this VLAN.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.248.12.2.2.5.1.2
hm2AgentSwitchIpVlanRoutingStatus Status of Routing mode per VLAN. active(1) - VLAN is enabled for routing createAndGo(4) - Adds VLAN entry for routing createAndWait(5) - Adds VLAN entry for routing destroy(6) - Removes VLAN from routing	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.2.5.1.3

Contains a list of secondary IP addresses associated with an interface.

hm2AgentSwitchSecondaryAddressEntry row .1.3.6.1.4.1.248.12.2.2.6.1

A secondary IP address for a given interface. This IP address must not
conflict with the IP address configured in the hm2AgentSwitchIpInterfaceTable.

Indexes

hm2AgentSwitchIpInterfaceIfIndex hm2AgentSwitchSecondaryIpAddress

Column	Syntax	OID
hm2AgentSwitchSecondaryIpAddress The secondary IP address assigned to this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.6.1.1
hm2AgentSwitchSecondaryNetMask The secondary netmask assigned to this interface. This value must be set during creation and can not be changed.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.6.1.2
hm2AgentSwitchSecondaryStatus Creates a new entry in the secondary address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The hm2AgentSwitchSecondaryNetMask objec…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.2.6.1.3

Contains a list of IP helper addresses associated with an interface.

hm2AgentSwitchIntfIpHelperAddressEntry row .1.3.6.1.4.1.248.12.2.2.10.1

An IP helper address for a given interface.

Indexes

hm2AgentSwitchIpInterfaceIfIndex hm2AgentSwitchIntfIpHelperUdpPort hm2AgentSwitchIntfIpHelperIpAddress

Column	Syntax	OID
hm2AgentSwitchIntfIpHelperUdpPort UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and ne…	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.4.1.248.12.2.2.10.1.1
hm2AgentSwitchIntfIpHelperIpAddress An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.2.10.1.2
hm2AgentSwitchIntfIpHelperHitCount The number of times a packet has been forwarded or discarded according to this entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.2.10.1.4
hm2AgentSwitchIntfIpHelperStatus Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.2.10.1.5

This table contains the MIB objects required to configure 
route-redistribution for RIP. Here, RIP is the Destination
protocol and the source protocols can be any of : BGP, OSPF,
Static, Connected.

hm2AgentRipRouteRedistEntry row .1.3.6.1.4.1.248.12.2.3.8.1

The entries of the table.

Indexes

hm2AgentRipRouteRedistSource

Column	Syntax	OID
hm2AgentRipRouteRedistSource Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.	Enumeration Enumerated Values: 1 connected 2 static 3 ospf 4 bgp	.1.3.6.1.4.1.248.12.2.3.8.1.1
hm2AgentRipRouteRedistMode User enabels/disables route-redistribution for a particular source protocol.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.3.8.1.2
hm2AgentRipRouteRedistMetric Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.248.12.2.3.8.1.3
hm2AgentRipRouteRedistMetricConfigured Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.3.8.1.4
hm2AgentRipRouteRedistMatchInternal If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.248.12.2.3.8.1.5
hm2AgentRipRouteRedistMatchExternal1 If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.248.12.2.3.8.1.6
hm2AgentRipRouteRedistMatchExternal2 If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.248.12.2.3.8.1.7
hm2AgentRipRouteRedistMatchNSSAExternal1 If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.248.12.2.3.8.1.8
hm2AgentRipRouteRedistMatchNSSAExternal2 If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.	Enumerationr/w Enumerated Values: 1 true 2 false 3 not-applicable	.1.3.6.1.4.1.248.12.2.3.8.1.9
hm2AgentRipRouteRedistDistList Access-list number of the access-list, which filters routes received from a source-protocol.	Unsigned32r/w Constraints: range: 1000-1099 range: 0-0	.1.3.6.1.4.1.248.12.2.3.8.1.10
hm2AgentRipRouteRedistDistListConfigured Flag to determine whether Access-list is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.3.8.1.11

A list of subnets which require separate
configuration in RIP.  Augments rip2IfConfTable
in the RIPv2-MIB.

hm2AgentRip2IfConfEntry row .1.3.6.1.4.1.248.12.2.3.9.1

A Single Routing Domain in a single Subnet.
Augments rip2IfConfEntry in RIPv2-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentRip2IfConfAuthKeyId The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.3.9.1.1

This table contains the MIB objects required to configure 
route-redistribution for OSPF. Here, OSPF is the Destination
protocol and the source protocols can be any of : BGP, RIP,
Static, Connected.

hm2AgentOspfRouteRedistEntry row .1.3.6.1.4.1.248.12.2.4.8.1

The entries of the table.

Indexes

hm2AgentOspfRouteRedistSource

Column	Syntax	OID
hm2AgentOspfRouteRedistSource Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.	Enumeration Enumerated Values: 1 connected 2 static 3 rip 4 bgp	.1.3.6.1.4.1.248.12.2.4.8.1.1
hm2AgentOspfRouteRedistMode User enables/disables route-redistribution for a particular source protocol.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.8.1.2
hm2AgentOspfRouteRedistMetric Metric used for redistributing a particular source protocol route into OSPF.	Integer32r/w Constraints: range: 0-16777214	.1.3.6.1.4.1.248.12.2.4.8.1.3
hm2AgentOspfRouteRedistMetricConfigured Flag to determine whether OSPF redistribute-metric is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.4.8.1.4
hm2AgentOspfRouteRedistMetricType Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).	Enumerationr/w Enumerated Values: 1 externalType1 2 externalType2	.1.3.6.1.4.1.248.12.2.4.8.1.5
hm2AgentOspfRouteRedistTag It specifies the tag field in routes redistributed by OSPF.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.4.8.1.6
hm2AgentOspfRouteRedistSubnets If this value is false, then OSPF will not redistribute subnetted routes.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.4.8.1.7
hm2AgentOspfRouteRedistDistList Access-list number of the access-list, which filters routes received from a source-protocol. HiOS: Valid access list numbers are between 1000 and 1099. HiSecOS: Valid access list numbers are between 1 and 10000.	Unsigned32r/w Constraints: range: 0-10000	.1.3.6.1.4.1.248.12.2.4.8.1.8
hm2AgentOspfRouteRedistDistListConfigured Flag to determine whether Access-list is configured or not.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.4.8.1.9

The OSPF Interface Table describes the  inter-
faces from the viewpoint of OSPF.  Augments 
ospfIfTable from the OSPF-MIB.

hm2AgentOspfIfEntry row .1.3.6.1.4.1.248.12.2.4.9.1

The OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF. Augments
ospfIfEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentOspfIfAuthKeyId The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.4.9.1.1
hm2AgentOspfIfIpMtuIgnoreFlag Configures the IP MTU Ignore Flag value for this OSPF interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.9.1.2
hm2AgentOspfIfPassiveMode Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.4.9.1.3
hm2AgentOspfIfAdvertiseSecondaries Configures the advertisability of the secondary addresses configured on this interface.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.9.1.4
hm2AgentOspfIfFastHelloMode Configures the fast hello mode on this interface. If enabled, hello packets are sent every 250ms, ospfIfHelloInterval is ignored. The dead interval and spf delay need to be re-configured accordingly for faster convergen…	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.9.1.248

Information about this router's virtual inter-
faces.  Augments ospfVirtIfTable from the OSPF-MIB.

hm2AgentOspfVirtIfEntry row .1.3.6.1.4.1.248.12.2.4.10.1

Information about a single Virtual Interface.
Augments ospfVirtIfEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentOspfVirtIfAuthKeyId The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.4.10.1.1

The OSPF Process's Area Link State Database (LSDB). 
The LSDB contains type-10 Link State Advertisements 
from throughout the areas that the device is attached to.

hm2AgentOspfAreaOpaqueLsdbEntry row .1.3.6.1.4.1.248.12.2.4.16.1

A single AreaOpaque Link State Advertisement.

Indexes

hm2AgentOspfAreaOpaqueLsdbAreaId hm2AgentOspfAreaOpaqueLsdbType hm2AgentOspfAreaOpaqueLsdbLsid hm2AgentOspfAreaOpaqueLsdbRouterId

Column	Syntax	OID
hm2AgentOspfAreaOpaqueLsdbAreaId The 32 bit identifier of the Area from which the LSA was received.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.4.16.1.1
hm2AgentOspfAreaOpaqueLsdbType The type of the link state advertisement. Each link state type has a separate advertisement format.	Enumeration Enumerated Values: 10 areaOpaqueLink	.1.3.6.1.4.1.248.12.2.4.16.1.2
hm2AgentOspfAreaOpaqueLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.4.16.1.3
hm2AgentOspfAreaOpaqueLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.248.12.2.4.16.1.4
hm2AgentOspfAreaOpaqueLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.16.1.5
hm2AgentOspfAreaOpaqueLsdbAge This field is the age of the link state advertisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.16.1.6
hm2AgentOspfAreaOpaqueLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.16.1.7
hm2AgentOspfAreaOpaqueLsdbAdvertisement The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.248.12.2.4.16.1.8

The OSPF Process's Link-Local Link State Database 
for non-virtual links. 
This table is identical to the OSPF LSDB Table 
in format, but contains only Link-Local Link State 
Advertisements for non-virtual links. The purpose is 
to allow Link-Local LSAs to be displayed for each 
non-virtual interface. This table is implemented to 
support type-9 LSAs which are defined 
in 'The OSPF Opaque LSA Option'.

hm2AgentOspfLocalLsdbEntry row .1.3.6.1.4.1.248.12.2.4.17.1

A single Link State Advertisement.

Indexes

hm2AgentOspfLocalLsdbIpAddress hm2AgentOspfLocalLsdbAddressLessIf hm2AgentOspfLocalLsdbType hm2AgentOspfLocalLsdbLsid hm2AgentOspfLocalLsdbRouterId

Column	Syntax	OID
hm2AgentOspfLocalLsdbIpAddress The IP Address of the interface from which the LSA was received if the interface is numbered.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.4.17.1.1
hm2AgentOspfLocalLsdbAddressLessIf The Interface Index of the interface from which the LSA was received if the interface is unnumbered.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.248.12.2.4.17.1.2
hm2AgentOspfLocalLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 9 localOpaqueLink	.1.3.6.1.4.1.248.12.2.4.17.1.3
hm2AgentOspfLocalLsdbLsid The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.4.17.1.4
hm2AgentOspfLocalLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.248.12.2.4.17.1.5
hm2AgentOspfLocalLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.17.1.6
hm2AgentOspfLocalLsdbAge This field is the age of the link state adver- tisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.17.1.7
hm2AgentOspfLocalLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The check…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.17.1.8
hm2AgentOspfLocalLsdbAdvertisement The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.248.12.2.4.17.1.9

The OSPF Process's AS-scope LSA Link State Database. 
The Database contains the AS-scope Link State 
Advertisements from throughout the areas that 
the device is attached to. 
          
This table is identical to the OSPF LSDB Table 
in format, but contains only AS-scope Link State 
Advertisements.  The purpose is to allow AS-scope 
LSAs to be displayed once for the router rather 
than once in each non-stub area.

hm2AgentOspfAsLsdbEntry row .1.3.6.1.4.1.248.12.2.4.18.1

A single Link State Advertisement.

Indexes

hm2AgentOspfAsLsdbType hm2AgentOspfAsLsdbLsid hm2AgentOspfAsLsdbRouterId

Column	Syntax	OID
hm2AgentOspfAsLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 11 asOpaqueLink	.1.3.6.1.4.1.248.12.2.4.18.1.1
hm2AgentOspfAsLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.4.18.1.2
hm2AgentOspfAsLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.248.12.2.4.18.1.3
hm2AgentOspfAsLsdbSequence The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to det…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.18.1.4
hm2AgentOspfAsLsdbAge This field is the age of the link state adver- tisement in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.18.1.5
hm2AgentOspfAsLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The check…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.4.18.1.6
hm2AgentOspfAsLsdbAdvertisement The entire Link State Advertisement, including its header.	OctetString Constraints: range: 1-65535	.1.3.6.1.4.1.248.12.2.4.18.1.7

Information about all the configured Not-So-Stubby-Area(NSSAs) in OSPF.  
Augments ospfAreaTable from the OSPF-MIB.

hm2AgentOspfAreaNSSAEntry row .1.3.6.1.4.1.248.12.2.4.248.1

Information about a single Not-So-Stubby-Area(NSSA).
Augments ospfAreaEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentOspfAreaNSSAImportSummaries When set to enabled, OSPF's summary routes are imported into the NSSA as Type-3 summary-LSAs. When set to disabled, summary routes are not imported into the NSSA. The default setting is enabled.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.248.1.1
hm2AgentOspfAreaNSSARedistribute When set to enabled NSSA ASBRs will not redistribute external routes into the NSSA and they will cease to originate Type-7 external LSAs for external routes.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.4.248.1.2
hm2AgentOspfAreaNSSADefaultInfoOriginate Determines if the router will originate a Type-7 default LSA into the NSSA. This command will cause a default LSA to be originated only if the router is an NSSA ABR or ASBR.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.4.248.1.3
hm2AgentOspfAreaNSSADefaultMetric Defines the metric value advertised in the Type-7 default LSA originated by this router	Integer32r/w Constraints: range: 1-16777214	.1.3.6.1.4.1.248.12.2.4.248.1.4
hm2AgentOspfAreaNSSADefaultMetricType Defines the metric type advertised in the Type-7 default LSA originated by this router	Enumerationr/w Enumerated Values: 1 ospfMetric 2 comparable 3 nonComparable	.1.3.6.1.4.1.248.12.2.4.248.1.5

Information about interface metrics.

hm2AgentOspfIfMetricEntry row .1.3.6.1.4.1.248.12.2.4.249.1

Information about interface metrics.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentOspfIfMetricCalculatedCost Returns the actual cost value used by OSPF for this interface.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.248.12.2.4.249.1.1

Operations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
`hm2AgentRouterVrrpOperEntry' items.

hm2AgentRouterVrrpOperEntry row .1.3.6.1.4.1.248.12.2.9.1.1

An entry in the table contains operational priority that is
associated with a virtual router.

Indexes

IF-MIBifIndex VRRP-MIBvrrpOperVrId

Column	Syntax	OID
hm2AgentRouterVrrpOperPriorityobsolete This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.9.1.1.1

Contains a list of IP helper addresses configured globally.

hm2AgentSwitchIpHelperAddressEntry row .1.3.6.1.4.1.248.12.2.11.8.1

An IP Helper address that applies to packets received on any interface.

Indexes

hm2AgentSwitchIpHelperUdpPort hm2AgentSwitchIpHelperAddress

Column	Syntax	OID
hm2AgentSwitchIpHelperUdpPort UDP port number. A relay entry with port 0 allows dhcp, time, winnameserver, tacacs, dns, tftp, netbios-ns and netbios-dgm relay.	Unsigned32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.248.12.2.11.8.1.1
hm2AgentSwitchIpHelperAddress The IP Helper address assigned to this interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.11.8.1.2
hm2AgentSwitchIpHelperHitCount The number of times a packet has been forwarded or discarded according to this entry.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.11.8.1.3
hm2AgentSwitchIpHelperStatus Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.11.8.1.4

Contains a list of VLAN IDs used internally for port-based routing interfaces.

hm2AgentSwitchInternalVlanEntry row .1.3.6.1.4.1.248.12.2.12.3.1

A VLAN ID internally assigned to a port-based routing interface.

Indexes

hm2AgentSwitchInternalVlanId

Column	Syntax	OID
hm2AgentSwitchInternalVlanId A VLAN ID internally assigned to a port-based routing interface.	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.248.12.2.12.3.1.1
hm2AgentSwitchInternalVlanIfIndex Interface index of port-based routing interface using this VLAN ID.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.248.12.2.12.3.1.2

Table lists information about OSPFv2 message queue utilization.

hm2AgentOspfQueueEntry row .1.3.6.1.4.1.248.12.2.13.1.1

Information on a specific OSPFv2 message queue.

Indexes

hm2AgentOspfQueueIndex

Column	Syntax	OID
hm2AgentOspfQueueIndex Index value for this message queue.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.13.1.1.1
hm2AgentOspfQueueName Name of an OSPFv2 message queue.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.12.2.13.1.1.2
hm2AgentOspfQueueLength The number of messages currently in the message queue.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.13.1.1.3
hm2AgentOspfQueueHigh The high water mark of the number of messages in the message queue.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.13.1.1.4
hm2AgentOspfQueueDrops The number of items dropped because the message queue was full.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.13.1.1.5
hm2AgentOspfQueueLimit The maximum number of messages this queue can hold.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.13.1.1.6

Contains statistics for the twenty most recent SPF runs. 
Statistics are reported from the oldest SPF first to the most recent.

hm2AgentOspfSpfStatsEntry row .1.3.6.1.4.1.248.12.2.15.1

Statistics for a single SPF run.

Indexes

hm2AgentOspfSpfIndex

Column	Syntax	OID
hm2AgentOspfSpfIndex Integer that uniquely identifies an SPF run. This value is incremented each time OSPF runs a full routing table calculation.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.1
hm2AgentOspfSpfStatsDeltaT How long since this routing table calculation ran. The time is given in seconds.	secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.2
hm2AgentOspfSpfStatsIntra Number of milliseconds to compute intra-area routes.	milli-secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.3
hm2AgentOspfSpfStatsSumm Number of milliseconds to compute inter-area routes.	milli-secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.4
hm2AgentOspfSpfStatsExt Number of milliseconds to compute external routes.	milli-secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.5
hm2AgentOspfSpfStatsSpfTotal Number of milliseconds for entire routing table calculation.	milli-secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.6
hm2AgentOspfSpfStatsRibUpdate Number of milliseconds to update the common routing table.	milli-secondsSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.15.1.7
hm2AgentOspfSpfStatsReason Reasons why a routing table calculation was required. R - new router LSA, N - new Network LSA, SN - new network summary LSA, SA - new ASBR summary LSA, X - new external LSA.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.248.12.2.15.1.8

A count of the number of routes with each number of ECMP next hops.

hm2AgentEcmpCountEntry row .1.3.6.1.4.1.248.12.2.18.1

Number of IPv4 routes with a given number of next hops.

Indexes

hm2AgentEcmpNextHopCount

Column	Syntax	OID
hm2AgentEcmpNextHopCount The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform.	Unsigned32 Constraints: range: 0-128	.1.3.6.1.4.1.248.12.2.18.1.1
hm2AgentEcmpRouteCount The number of IPv4 routes with agentEcmpNextHopCount next hops.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.18.1.2

Information about this router's neighbors.
Augments ospfNbrTable from the OSPF-MIB.

hm2AgentOspfNbrEntry row .1.3.6.1.4.1.248.12.2.249.1

Information about a single neighbor.
Augments ospfNbrEntry in OSPF-MIB.

Indexes

No indexes recorded

Column	Syntax	OID
hm2AgentOspfNbrDeadTime The neighbor's Dead Time is the amount of remaining time since the last OSPF hello packet received, before declaring the neighbor status as down.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.248.12.2.249.1.1

Information about this router's OSPF routes.

hm2AgentOspfRouteEntry row .1.3.6.1.4.1.248.12.2.250.1

Information about a single route.

Indexes

hm2AgentOspfRouteNet hm2AgentOspfRouteMask

Column	Syntax	OID
hm2AgentOspfRouteNet The IP Address of the Net or Subnet indicated by the route.	INET-ADDRESS-MIBInetAddressIPv4 Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.250.1.1
hm2AgentOspfRouteMask The Subnet Mask that pertains to the Net or Subnet.	INET-ADDRESS-MIBInetAddressIPv4 Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.250.1.2
hm2AgentOspfRouteCost The route cost calculated in the SPF algorithm to reach the network.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.250.1.3
hm2AgentOspfRouteProtoType The type of route that was learned from OSPF.	Enumeration Enumerated Values: 1 intra 2 inter 3 ext-type1 4 ext-type2 5 nssa-type1 6 nssa-type2	.1.3.6.1.4.1.248.12.2.250.1.4

This table contains variables to define
an entry in the VRRP Tracking database.

hm2AgentVrrpTrackingEntry row .1.3.6.1.4.1.248.12.2.260.1.1

The entries of the table.

Indexes

hm2AgentVrrpTrackIfIndex hm2AgentVrrpTrackVrid hm2AgentVrrpTrackId

Column	Syntax	OID
hm2AgentVrrpTrackIfIndex DURABLE: { 1:all } The interface number of the virtual router	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.260.1.1.1
hm2AgentVrrpTrackVrid DURABLE: { 1:all } The virtual router id for this virtual router	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.248.12.2.260.1.1.2
hm2AgentVrrpTrackId DURABLE: { 1:all } The id of the object being tracked	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.248.12.2.260.1.1.3
hm2AgentVrrpTrackDecrement DURABLE: { 1:all } The value by wich the current priority of the virtual router is decremented when the tracked object goes DOWN.	Integer32r/w Constraints: range: 1-253	.1.3.6.1.4.1.248.12.2.260.1.1.4
hm2AgentVrrpTrackOperStatus Shows if the tracked object is currently UP or DOWN or NOT-READY	Enumeration Enumerated Values: 1 up 2 down 3 notReady	.1.3.6.1.4.1.248.12.2.260.1.1.5
hm2AgentVrrpTrackRowStatus DURABLE: { 1:all } Defines the status of a vrrp tracking database entry. Set to createAndGo(4) to create a new row. Set to destroy(6) to delete an entry. Reads as active(1) if the tracked object exists and is trackable,…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.260.1.1.6

This table contains variables to define
an entry in the VRRP enhancements database.

hm2AgentVrrpExtEntry row .1.3.6.1.4.1.248.12.2.260.2.1

The entry of the hm2AgentVrrpExtTable.

Indexes

hm2AgentVrrpExtIfIndex hm2AgentVrrpExtVrid

Column	Syntax	OID
hm2AgentVrrpExtIfIndex The interface number of the virtual router	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.260.2.1.1
hm2AgentVrrpExtVrid The virtual router id for this virtual router	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.248.12.2.260.2.1.2
hm2AgentVrrpExtDomainId The domain this virtual router is a member of. If set to 0, the virtual router is not a member of any domain.	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.248.12.2.260.2.1.3
hm2AgentVrrpExtDomainRole The role of this virtual router in its domain. This is none(1) if the virtual router is not member of a domain, supervisor(3) if it is the supervisor of its domain, member(2) otherwise.	Enumerationr/w Enumerated Values: 1 none 2 member 3 supervisor	.1.3.6.1.4.1.248.12.2.260.2.1.4
hm2AgentVrrpExtDomainStatus Shows if the domain configuration is correct for this virtual router	Enumeration Enumerated Values: 1 noError 2 noSupervisor 3 supervisorDown	.1.3.6.1.4.1.248.12.2.260.2.1.5
hm2AgentVrrpExtAdvertAddress The IP address advertisements of the virtual router are sent to	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.260.2.1.6
hm2AgentVrrpExtAdvertTimer This is used to set the interval between advertisements in milliseconds. This accesses the same value as vrrpOperAdvertisementInterval.	milli-secondsInteger32r/w Constraints: range: 100-255000	.1.3.6.1.4.1.248.12.2.260.2.1.7
hm2AgentVrrpExtCfgPriority The configured priority of the virtual router. This can be different from the operating priority if tracked objects are down or the virtual router is the ip address owner	Integer32r/w Constraints: range: 1-254	.1.3.6.1.4.1.248.12.2.260.2.1.8
hm2AgentVrrpExtNotifyAddress The IP address notifications of the virtual router are sent to	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.260.2.1.9
hm2AgentVrrpExtNotifyLinkdown Enables or disables sending of notification messages if the virtual router's interface goes down.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.260.2.1.10
hm2AgentVrrpExtPreemptionDelay Time (in seconds) after startup of the virtual router by which the preemption of a Master with a lower priority is delayed.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.248.12.2.260.2.1.11
hm2AgentVrrpPrimaryVirtualAddress The virtual IP address in the subnet of the primary ip address on the interface. If no match is found, an unspecified virtual address is returned. If no virtual address is configured, 0.0.0.0 is returned.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.248.12.2.260.2.1.12
hm2AgentVrrpExtMethod The source of the VRRP instance. User can set the object to none(1), config(2), ttdp(3).	Enumerationr/w Enumerated Values: 1 none 2 config 3 ttdp	.1.3.6.1.4.1.248.12.2.260.2.1.13
hm2AgentVrrpExtProxyarp This object specifies if proxy arp functionality must be associated with a vrrp instance. Possible values: - true: enable proxy arp on change of vrrpOperState to master - false: No impact NOTE: Set the value to true wh…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.248.12.2.260.2.1.14

This table contains variables to define
an entry in the VRRP domain database.

hm2AgentVrrpDomainEntry row .1.3.6.1.4.1.248.12.2.260.3.1

The entries of the table.

Indexes

hm2AgentVrrpDomainId

Column	Syntax	OID
hm2AgentVrrpDomainId The domain ID.	Integer32 Constraints: range: 0-8	.1.3.6.1.4.1.248.12.2.260.3.1.1
hm2AgentVrrpDomainMemberSendAdv DURABLE: { 1:all } Determines if the members of this domain send advertisement packets. If set to disabled(2), only the supervisor of the domain sends packets.	HM2-TC-MIBHmEnabledStatusr/w Type Values: 1 enable 2 disable	.1.3.6.1.4.1.248.12.2.260.3.1.2
hm2AgentVrrpDomainStatus Shows if the configuration of the domain is complete.	Enumeration Enumerated Values: 1 noError 2 noSupervisor 3 supervisorDown	.1.3.6.1.4.1.248.12.2.260.3.1.3
hm2AgentVrrpDomainSupervisorIfIndex The interface number of the supervisor of the domain	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.248.12.2.260.3.1.4
hm2AgentVrrpDomainSupervisorVrid The virtual router id of the supervisor of the domain. 0 if unconfigured	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.260.3.1.5
hm2AgentVrrpDomainOperPriority The current operating priority of the domain. This can be different from the configured priority if tracked objects are down. For domain members this is the priority of the supervisor of that Domain if the supervisor is…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.248.12.2.260.3.1.6
hm2AgentVrrpDomainSupervisorOperState Shows the current operational state of the domain supervisor.	Enumeration Enumerated Values: 1 initialize 2 backup 3 master 4 unknown	.1.3.6.1.4.1.248.12.2.260.3.1.7

.

hm2AgentStaticNeighbourEntry row .1.3.6.1.4.1.248.12.2.270.10.1

.

Indexes

hm2AgentStaticNeighbourAddressType hm2AgentStaticNeighbourAddress

Column	Syntax	OID
hm2AgentStaticNeighbourAddressType .	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.248.12.2.270.10.1.1
hm2AgentStaticNeighbourAddress .	OctetString Constraints: range: 4-4 range: 16-16	.1.3.6.1.4.1.248.12.2.270.10.1.2
hm2AgentStaticNeighbourPhysAddress .	OctetStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.248.12.2.270.10.1.3
hm2AgentStaticNeighbourIfIndex .	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.248.12.2.270.10.1.4
hm2AgentStaticNeighbourRowStatus The status of this entry. Setting this object destroy will remove the entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.248.12.2.270.10.1.5

.

hm2AgentDynamicNeighbourEntry row .1.3.6.1.4.1.248.12.2.270.11.1

.

Indexes

hm2AgentDynamicNeighbourAddressType hm2AgentDynamicNeighbourAddress

Column	Syntax	OID
hm2AgentDynamicNeighbourAddressType .	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.248.12.2.270.11.1.1
hm2AgentDynamicNeighbourAddress .	OctetString Constraints: range: 4-4 range: 16-16	.1.3.6.1.4.1.248.12.2.270.11.1.2
hm2AgentDynamicNeighbourPhysAddress .	OctetString Constraints: range: 0-65535	.1.3.6.1.4.1.248.12.2.270.11.1.3
hm2AgentDynamicNeighbourIfIndex .	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.248.12.2.270.11.1.4
hm2AgentDynamicNeighbourAction .	Enumerationr/w Enumerated Values: 1 other 2 delete 3 static	.1.3.6.1.4.1.248.12.2.270.11.1.5