HM2-DIAGNOSTIC-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

106

hm2SigConCommonTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.1 · 1 row entry · 18 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConCommonTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConCommonTable'

This table contains all variables to configure the behavior
of the signalling contacts.

hm2SigConCommonEntry row .1.3.6.1.4.1.248.11.22.1.3.1.1.1

The entry of the hm2SigConConfigTable.

Indexes

hm2SigConID

Column Syntax OID

hm2SigConID

This index is used to identify the associated signalling contact.

Integer32

Constraints:
range: 1-2

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.1

hm2SigConTrapEnable

Determines whether a trap shall be sent or not, when
the signal contact operating state changes.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.2

hm2SigConTrapCause

This object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hm2SigConTrapCauseIndex.

Enumeration

Enumerated Values:

1	none
2	power-supply
3	link-failure
4	temperature
5	fan-failure
6	module-removal
7	ext-nvm-removal
8	ext-nvm-not-in-sync
9	ring-redundancy
10	password-change
11	password-min-length
12	password-policy-not-configured
13	password-policy-inactive
14	telnet-enabled
15	http-enabled
16	snmp-unsecure
17	sysmon-enabled
18	ext-nvm-update-enabled
19	no-link
20	hidisc-enabled
21	ext-nvm-config-load-unsecure
23	https-certificate-warning
24	modbus-tcp-enabled
25	ethernet-ip-enabled
26	profinet-io-enabled
27	ethernet-loops
28	humidity
29	pml-disabled
30	stp-port-blocked

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.3

hm2SigConTrapCauseIndex

This attribute specifies the entity which produces the trap.
power-supply: index of power-supply table
link-failure: index of interface table
temperature: 0
ext-nvm-removal: (1) sd, (2) usb, (3) serial (not supp…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.4

hm2SigConMode

This attribute specifies the behavior of the relay contact.
The factory settings for signal contact 1 is monitoring the
correct operation of entries specified to be survived.
When the device has also a second signal con…

Enumerationr/w

Enumerated Values:

1	manual
2	monitor
3	deviceState
4	deviceSecurity
5	deviceStateAndSecurity

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.5

hm2SigConOperState

This attribute shows the current operating state of the
signal contact.

Enumeration

Enumerated Values:

1	open
2	close

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.6

hm2SigConOperTimeStamp

This attribute shows local system time (hm2SystemLocalTime) of the last hm2SigConOperState change.

HM2-TC-MIBHmTimeSeconds1970

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.7

hm2SigConManualActivate

When operating in manual mode, the signal contact state can
be set by this attribute.

Enumerationr/w

Enumerated Values:

1	open
2	close

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.8

hm2SigConSenseLinkFailure

Sets the monitoring of the network connection(s).

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.9

hm2SigConSenseTemperature

Sets the monitoring of the device temperature.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.10

hm2SigConSenseFan

Sets the monitoring of the device fan modules.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.11

hm2SigConSenseModuleRemoval

Sets the monitoring of module removal (platform dependant).

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.12

hm2SigConSenseExtNvmRemoval

Sets the monitoring of the external non-volatile memory removal.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.13

hm2SigConSenseExtNvmNotInSync

Sets the monitoring whether the external non-volatile memory is in
sync with the configuration in NVRAM.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.14

hm2SigConSenseRingRedundancy

Sets the monitoring of the ring redundancy.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.15

hm2SigConSenseEthernetLoops

Sets the monitoring for Ethernet loops.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.16

hm2SigConSenseHumidity

Sets the monitoring of the device humidity.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.17

hm2SigConSenseStpPortBlock

Sets the monitoring for STP loops.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.1.1.18

hm2SigConPSTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.2 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConPSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConPSTable'

This table contains the configuration of all power supply states.

hm2SigConPSEntry row .1.3.6.1.4.1.248.11.22.1.3.1.2.1

The entry of the hm2SigConPSTable.

Indexes

hm2SigConID HM2-PWRMGMT-MIBhm2PSID

Column Syntax OID

hm2SigConSensePSState

Sets the monitoring of the power supply state.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.2.1.1

hm2SigConInterfaceTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.3 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConInterfaceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConInterfaceTable'

This table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifIndex. The table is also used
for the device monitoring configuration.

hm2SigConInterfaceEntry row .1.3.6.1.4.1.248.11.22.1.3.1.3.1

The entry of the hm2SigConLinkTable.

Indexes

hm2SigConID IF-MIBifIndex

Column Syntax OID

hm2SigConSenseIfLinkAlarm

Indicates whether an alarm for the signalling relay of the
associated link will be produced or not, so you can mask the
value of ifMauMediaAvailable.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.3.1.1

hm2SigConModuleTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.4 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConModuleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConModuleTable'

This table contains all variables to mask a module for the
signaling relay. The index for a module corresponds with the 
slot number.

hm2SigConModuleEntry row .1.3.6.1.4.1.248.11.22.1.3.1.4.1

The entry of the hm2SigConModuleTable.

Indexes

hm2SigConID hm2SigConModID

Column Syntax OID

hm2SigConModID

This index is used to identify the associated module.

Integer32

Constraints:
range: 1-7

.1.3.6.1.4.1.248.11.22.1.3.1.4.1.1

hm2SigConSenseModule

Indicates whether an alarm for the signalling relay of the
associated module will be produced or not.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.4.1.2

hm2SigConFanModuleTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.5 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConFanModuleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConFanModuleTable'

This table contains all variables to mask a fan module for the
signaling relay. The index for a module corresponds with the 
module number.

hm2SigConFanModuleEntry row .1.3.6.1.4.1.248.11.22.1.3.1.5.1

The entry of the hm2SigConFanModuleTable.

Indexes

hm2SigConID hm2SigConFanModID

Column Syntax OID

hm2SigConFanModID

This index is used to identify the associated fan module.

Integer32

Constraints:
range: 1-7

.1.3.6.1.4.1.248.11.22.1.3.1.5.1.1

hm2SigConSenseFanModule

Indicates whether an alarm for the signalling relay of the
associated fan module will be produced or not.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.1.5.1.2

hm2SigConStatusTable

table

.1.3.6.1.4.1.248.11.22.1.3.1.10 · 1 row entry · 4 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2SigConStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2SigConStatusTable'

This table shows the current monitored entities
for which there is a trap cause (hm2SigConTrapCause) active.

hm2SigConStatusEntry row .1.3.6.1.4.1.248.11.22.1.3.1.10.1

The entry of the hm2SigConStatusTable.

Indexes

hm2SigConID hm2SigConStatusIndex

Column Syntax OID

hm2SigConStatusIndex

This index is used to identify the occured event.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.1.10.1.1

hm2SigConStatusTimeStamp

This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.

HM2-TC-MIBHmTimeSeconds1970

.1.3.6.1.4.1.248.11.22.1.3.1.10.1.2

hm2SigConStatusTrapCause

This object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hm2SigConTrapCauseIndex.

Enumeration

Enumerated Values:

1	none
2	power-supply
3	link-failure
4	temperature
5	fan-failure
6	module-removal
7	ext-nvm-removal
8	ext-nvm-not-in-sync
9	ring-redundancy
10	password-change
11	password-min-length
12	password-policy-not-configured
13	password-policy-inactive
14	telnet-enabled
15	http-enabled
16	snmp-unsecure
17	sysmon-enabled
18	ext-nvm-update-enabled
19	no-link
20	hidisc-enabled
21	ext-nvm-config-load-unsecure
22	iec61850-mms-enabled
23	https-certificate-warning
24	modbus-tcp-enabled
25	ethernet-ip-enabled
26	profinet-io-enabled
27	ethernet-loops
28	humidity
30	stp-port-blocked

.1.3.6.1.4.1.248.11.22.1.3.1.10.1.3

hm2SigConStatusTrapCauseIndex

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.1.10.1.4

hm2DevMonCommonTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.1 · 1 row entry · 15 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonCommonTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonCommonTable'

This table contains all variables to configure the behavior
of the signalling contacts.

hm2DevMonCommonEntry row .1.3.6.1.4.1.248.11.22.1.3.2.1.1

The entry of the hm2DevMonConfigTable.

Indexes

hm2DevMonID

Column Syntax OID

hm2DevMonID

This index is used to identify the associated device monitoring group.
Currently only one group is supported

Integer32

Constraints:
range: 1-1

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.1

hm2DevMonTrapEnable

Determines whether a trap shall be sent or not when
the signal contact operating state changes.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.2

hm2DevMonTrapCause

This object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hm2DevMonTrapCauseIndex.

Enumeration

Enumerated Values:

1	none
2	power-supply
3	link-failure
4	temperature
5	fan-failure
6	module-removal
7	ext-nvm-removal
8	ext-nvm-not-in-sync
9	ring-redundancy
28	humidity
30	stp-port-blocked

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.3

hm2DevMonTrapCauseIndex

This attribute specifies the entity which produces the trap.
power-supply: index of power supply table
link-failure: index of interface table
temperature: 0
ext-nvm-removal: (1) sd, (2) usb, (3) Serial (not supp…

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.4

hm2DevMonOperState

This attribute shows the current operating state of the
signal contact.

Enumeration

Enumerated Values:

1	noerror
2	error

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.5

hm2DevMonOperTimeStamp

This attribute shows the local system time (hm2SystemLocalTime) of the last hm2DevMonOperState change.

HM2-TC-MIBHmTimeSeconds1970

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.6

hm2DevMonSenseLinkFailure

Sets the monitoring of the network connection(s).

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.7

hm2DevMonSenseTemperature

Sets the monitoring of the device temperature.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.8

hm2DevMonSenseFan

Sets the monitoring of the device fan modules.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.9

hm2DevMonSenseModuleRemoval

Sets the monitoring of module removal (platform dependent).

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.10

hm2DevMonSenseExtNvmRemoval

Sets the monitoring of the external non-volatile memory removal.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.11

hm2DevMonSenseExtNvmNotInSync

Sets the monitoring whether the external non-volatile memory is in
sync with the configuration in NVRAM.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.12

hm2DevMonSenseRingRedundancy

Sets the monitoring of the ring redundancy.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.13

hm2DevMonSenseHumidity

Sets the monitoring of the device humidity.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.14

hm2DevMonSenseStpPortBlock

Sets the monitoring whether a port was blocked by STP.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.1.1.15

hm2DevMonPSTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.2 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonPSTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonPSTable'

This table contains the configuration of all power supply states.

hm2DevMonPSEntry row .1.3.6.1.4.1.248.11.22.1.3.2.2.1

The entry of the hm2DevMonPSTable.

Indexes

hm2DevMonID HM2-PWRMGMT-MIBhm2PSID

Column Syntax OID

hm2DevMonSensePSState

Sets the monitoring of the power supply state.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.2.1.1

hm2DevMonInterfaceTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.3 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonInterfaceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonInterfaceTable'

This table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifIndex. The table is also used
for the device monitoring configuration.

hm2DevMonInterfaceEntry row .1.3.6.1.4.1.248.11.22.1.3.2.3.1

The entry of the hm2DevMonLinkTable.

Indexes

hm2DevMonID IF-MIBifIndex

Column Syntax OID

hm2DevMonSenseIfLinkAlarm

Indicates whether an alarm for the signalling relay of the
associated link will be produced or not, so you can mask the
value of ifMauMediaAvailable.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.3.1.1

hm2DevMonModuleTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.4 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonModuleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonModuleTable'

This table contains all variables to mask a module for the
device status. The index for a module corresponds with the
slot number.

hm2DevMonModuleEntry row .1.3.6.1.4.1.248.11.22.1.3.2.4.1

The entry of the hm2DevMonModuleTable.

Indexes

hm2DevMonID hm2DevMonModID

Column Syntax OID

hm2DevMonModID

This index is used to identify the associated module.

Integer32

Constraints:
range: 1-7

.1.3.6.1.4.1.248.11.22.1.3.2.4.1.1

hm2DevMonSenseModule

Indicates whether an alarm for the device status of the
associated module will be produced or not.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.4.1.2

hm2DevMonFanModuleTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.5 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonFanModuleTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonFanModuleTable'

This table contains all variables to mask a fan module for the
device status. The index for a module corresponds with the
module number.

hm2DevMonFanModuleEntry row .1.3.6.1.4.1.248.11.22.1.3.2.5.1

The entry of the hm2DevMonFanModuleTable.

Indexes

hm2DevMonID hm2DevMonFanModID

Column Syntax OID

hm2DevMonFanModID

This index is used to identify the associated fan module.

Integer32

Constraints:
range: 1-7

.1.3.6.1.4.1.248.11.22.1.3.2.5.1.1

hm2DevMonSenseFanModule

Indicates whether an alarm for the device status of the
associated fan module will be produced or not.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.2.5.1.2

hm2DevMonStatusTable

table

.1.3.6.1.4.1.248.11.22.1.3.2.10 · 1 row entry · 4 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevMonStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevMonStatusTable'

This table shows the current monitored entities in the hm2DeviceMonitorGroup
for which there is a trap cause (hm2DevMonStatusTrapCause) active.

hm2DevMonStatusEntry row .1.3.6.1.4.1.248.11.22.1.3.2.10.1

The entry of the hm2DevMonStatusTable.

Indexes

hm2DevMonID hm2DevMonStatusIndex

Column Syntax OID

hm2DevMonStatusIndex

This index is used to identify the occured event.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.2.10.1.1

hm2DevMonStatusTimeStamp

This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.

HM2-TC-MIBHmTimeSeconds1970

.1.3.6.1.4.1.248.11.22.1.3.2.10.1.2

hm2DevMonStatusTrapCause

This object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hm2DevMonTrapCauseIndex.

Enumeration

Enumerated Values:

1	none
2	power-supply
3	link-failure
4	temperature
5	fan-failure
6	module-removal
7	ext-nvm-removal
8	ext-nvm-not-in-sync
9	ring-redundancy
28	humidity
30	stp-port-blocked

.1.3.6.1.4.1.248.11.22.1.3.2.10.1.3

hm2DevMonStatusTrapCauseIndex

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.2.10.1.4

hm2DevSecInterfaceTable

table

.1.3.6.1.4.1.248.11.22.1.3.3.2 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevSecInterfaceTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevSecInterfaceTable'

This table contains all variables to mask an alarm for the
signalling relay, produced by a link. The index for a link
corresponds with ifIndex. The table is also used
for the device monitoring configuration.

hm2DevSecInterfaceEntry row .1.3.6.1.4.1.248.11.22.1.3.3.2.1

The entry of the hm2DevSecLinkTable.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2DevSecSenseIfNoLink

Port has no link but admin state is up

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.3.3.2.1.1

hm2DevSecStatusTable

table

.1.3.6.1.4.1.248.11.22.1.3.3.10 · 1 row entry · 4 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DevSecStatusTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DevSecStatusTable'

This table shows the current monitored entities in the hm2DevSecConfigGroup
for which there is a trap cause (hm2DevSecStatusTrapCause) active.

hm2DevSecStatusEntry row .1.3.6.1.4.1.248.11.22.1.3.3.10.1

The entry of the hm2DevSecStatusTable.

Indexes

hm2DevSecStatusIndex

Column Syntax OID

hm2DevSecStatusIndex

This index is used to identify the occured event.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.3.10.1.1

hm2DevSecStatusTimeStamp

This attribute shows the local system time (hm2SystemLocalTime) of occuration the event.

HM2-TC-MIBHmTimeSeconds1970

.1.3.6.1.4.1.248.11.22.1.3.3.10.1.2

hm2DevSecStatusTrapCause

This object identifies the cause for a trap.
The index of the entity which produces the trap
is specified by hm2DevSecTrapCauseIndex.

Enumeration

Enumerated Values:

1	none
10	password-change
11	password-min-length
12	password-policy-not-configured
13	password-policy-inactive
14	telnet-enabled
15	http-enabled
16	snmp-unsecure
17	sysmon-enabled
18	ext-nvm-update-enabled
19	no-link
20	hidisc-enabled
21	ext-nvm-config-load-unsecure
22	iec61850-mms-enabled
23	https-certificate-warning
24	modbus-tcp-enabled
25	ethernet-ip-enabled
26	profinet-io-enabled
29	pml-disabled

.1.3.6.1.4.1.248.11.22.1.3.3.10.1.3

hm2DevSecStatusTrapCauseIndex

This attribute specifies the entity which produces the trap.
ext-nvm-update-enabled: (1) sd, (2) usb, (3) serial (not supported yet)
no-link: index of interface table
0: other errors.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.3.3.10.1.4

hm2LedGlobalTable

table

.1.3.6.1.4.1.248.11.22.1.4.1 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2LedGlobalTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2LedGlobalTable'

hm2LedGlobalEntry row .1.3.6.1.4.1.248.11.22.1.4.1.1

Indexes

hm2LedGlobalLedType

Column Syntax OID

hm2LedGlobalLedType

Hm2LedType

Type Values:

1	power
2	status
3	rm
4	envm
5	i1
6	i2

.1.3.6.1.4.1.248.11.22.1.4.1.1.1

hm2LedGlobalStatus

Hm2LedStatus

Type Values:

1	off
2	greenSolid
3	greenBlink1
4	greenBlink3
5	greenBlink4
6	greenBlink5
7	greenBlink5i
8	yellowSolid
9	yellowBlink1
10	yellowBlink3
11	yellowBlink4
12	yellowBlink5
13	redSolid
14	redBlink1
15	redBlink3
16	redBlink4
17	redBlink5

.1.3.6.1.4.1.248.11.22.1.4.1.1.2

hm2LedPortTable

table

.1.3.6.1.4.1.248.11.22.1.4.2 · 1 row entry · 3 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2LedPortTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2LedPortTable'

hm2LedPortEntry row .1.3.6.1.4.1.248.11.22.1.4.2.1

Indexes

HM2-DEVMGMT-MIBhm2IfacePhysIndex

Column Syntax OID

hm2LedPortStatus

Hm2LedStatus

Type Values:

1	off
2	greenSolid
3	greenBlink1
4	greenBlink3
5	greenBlink4
6	greenBlink5
7	greenBlink5i
8	yellowSolid
9	yellowBlink1
10	yellowBlink3
11	yellowBlink4
12	yellowBlink5
13	redSolid
14	redBlink1
15	redBlink3
16	redBlink4
17	redBlink5

.1.3.6.1.4.1.248.11.22.1.4.2.1.1

hm2LedPortPoeStatus

Hm2LedStatus

Type Values:

1	off
2	greenSolid
3	greenBlink1
4	greenBlink3
5	greenBlink4
6	greenBlink5
7	greenBlink5i
8	yellowSolid
9	yellowBlink1
10	yellowBlink3
11	yellowBlink4
12	yellowBlink5
13	redSolid
14	redBlink1
15	redBlink3
16	redBlink4
17	redBlink5

.1.3.6.1.4.1.248.11.22.1.4.2.1.2

hm2LedPortSignaling

Enable for LED port signaling.

HM2-TC-MIBHmEnabledStatusr/w

Type Values:

1	enable
2	disable

.1.3.6.1.4.1.248.11.22.1.4.2.1.3

hm2DiagIfaceUtilizationTable

table

.1.3.6.1.4.1.248.11.22.1.5.1 · 1 row entry · 5 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DiagIfaceUtilizationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DiagIfaceUtilizationTable'

This table contains variables for each interface of
the switch.

hm2DiagIfaceUtilizationEntry row .1.3.6.1.4.1.248.11.22.1.5.1.1

The entry of the hm2DiagIfaceUtilizationTable.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2DiagIfaceUtilization

The best estimate of the mean physical layer
network utilization on this interface during the
last sampling interval, in hundredth of one percent.
The first historyControlInterval (rfc1757) of this
interface is used as…

Integer32

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.1.1.1

hm2DiagIfaceUtilizationControlInterval

The interval in seconds over which the data is
sampled for hm2DiagIfaceUtilization.
This interval can be any number of seconds
between 1 and 3600 (1 hour).
The first historyControlInterval (rfc1757) of this
interface is…

Integer32r/w

Constraints:
range: 1-3600

.1.3.6.1.4.1.248.11.22.1.5.1.1.2

hm2DiagIfaceUtilizationAlarmLowerThreshold

Surveys the interface utilization hm2DiagIfaceUtilization and
generates an alarm for this interfaces, if
the utilization value is below the given limit.
A value of 0 disables the alarm generation.

Integer32r/w

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.1.1.3

hm2DiagIfaceUtilizationAlarmUpperThreshold

Surveys the interface utilization hm2DiagIfaceUtilization and
generates an alarm for this interfaces, if the given
limit is exceeded.
A value of 0 disables the alarm generation.

Integer32r/w

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.1.1.4

hm2DiagIfaceUtilizationAlarmCondition

The alarm condition is given (true), if the given
hm2DiagIfaceUtilizationAlarmUpperThreshold limit is exceeded
by the interface utilization or if the utilization value falls below
hm2DiagIfaceUtilizationAlarmLowerThre…

SNMPv2-TCTruthValue

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.5.1.1.5

hm2DiagEgressIfaceUtilizationTable

table

.1.3.6.1.4.1.248.11.22.1.5.2 · 1 row entry · 5 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DiagEgressIfaceUtilizationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DiagEgressIfaceUtilizationTable'

This table contains egress variables for each interface of
the switch.

hm2DiagEgressIfaceUtilizationEntry row .1.3.6.1.4.1.248.11.22.1.5.2.1

The entry of the hm2DiagEgressIfaceUtilizationTable.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2DiagEgressIfaceUtilization

The best estimate of the mean physical layer
network egress utilization on this interface during the
last sampling interval, in hundredth of one percent.
The first historyControlInterval (rfc1757) of this
interface is u…

Integer32

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.2.1.1

hm2DiagEgressIfaceUtilizationControlInterval

The interval in seconds over which the egress data is
sampled for hm2DiagEgressIfaceUtilization.
This interval can be any number of seconds
between 1 and 3600 (1 hour).
The first historyControlInterval (rfc1757) of this…

Integer32r/w

Constraints:
range: 1-3600

.1.3.6.1.4.1.248.11.22.1.5.2.1.2

hm2DiagEgressIfaceUtilizationAlarmLowerThreshold

Surveys the egress interface utilization hm2DiagEgressIfaceUtilization and
generates an alarm for this interface, if
the utilization value is below the given limit.
A value of 0 disables the alarm generation.

Integer32r/w

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.2.1.3

hm2DiagEgressIfaceUtilizationAlarmUpperThreshold

Surveys the egress interface utilization hm2DiagEgressIfaceUtilization and
generates an alarm for this interface, if the given
limit is exceeded.
A value of 0 disables the alarm generation.

Integer32r/w

Constraints:
range: 0-10000

.1.3.6.1.4.1.248.11.22.1.5.2.1.4

hm2DiagEgressIfaceUtilizationAlarmCondition

The alarm condition is given (true), if the given
hm2DiagEgressIfaceUtilizationAlarmUpperThreshold limit is exceeded
by the egress interface utilization or if the utilization value falls below
hm2DiagEgressIfaceUtiliz…

SNMPv2-TCTruthValue

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.5.2.1.5

hm2DiagCableTesterCableTable

table

.1.3.6.1.4.1.248.11.22.1.6.10 · 1 row entry · 5 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2DiagCableTesterCableTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2DiagCableTesterCableTable'

This table contains variables for each pair of
the cable.

hm2DiagCableTesterCableEntry row .1.3.6.1.4.1.248.11.22.1.6.10.1

The entry of the hm2DiagCableTesterCableTable.

Indexes

hm2DiagCableTesterCablePair

Column Syntax OID

hm2DiagCableTesterCablePair

Index of the hm2DiagCableTesterCableTable.
If a PHY does not support the measurement per pair,
the first index is used to show the values.

Integer32

Constraints:
range: 1-4

.1.3.6.1.4.1.248.11.22.1.6.10.1.1

hm2DiagCableTesterCableStatus

Indicates the results of the Cable Test.
normal(1) - The cable is working correctly.
open(2) - The cable is disconnected or there is a faulty
connector.
short(3) - There is an …

Enumeration

Enumerated Values:

1	normal
2	open
3	short
4	unknown

.1.3.6.1.4.1.248.11.22.1.6.10.1.2

hm2DiagCableTesterCableMinimumLength

The estimated length of the cable in meters. This value
indicates the shortest length estimated. This object will
return 0 if hm2DiagCableTesterStatus is not success(2) or the cable
length is unknown.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.248.11.22.1.6.10.1.3

hm2DiagCableTesterCableMaximumLength

The estimated length of the cable in meters. This value
indicates the longest length estimated. This object will
return 0 if hm2DiagCableTesterStatus is not success(2) or the cable
length is unknown.

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.248.11.22.1.6.10.1.4

hm2DiagCableTesterCableFailureLocation

The estimated distance in meters from the end of the cable to
the failure location. This object will return 0 if
hm2DiagCableTesterStatus is not success(2).

SNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.248.11.22.1.6.10.1.5

hm2PortMonitorIntfTable

table

.1.3.6.1.4.1.248.11.22.1.7.2 · 1 row entry · 2 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorIntfTable'

Port state mode interface table.

hm2PortMonitorIntfEntry row .1.3.6.1.4.1.248.11.22.1.7.2.1

Port state mode interface entry.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2PortMonitorIntfReset

Port monitor interface reset.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.2.1.2

hm2PortMonitorIntfAction

Interface link disable state.

Enumerationr/w

Enumerated Values:

1	port-disable
2	trap-only
3	auto-disable

.1.3.6.1.4.1.248.11.22.1.7.2.1.3

hm2PortMonitorConditionIntfTable

table

.1.3.6.1.4.1.248.11.22.1.7.3.1 · 1 row entry · 6 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorConditionIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorConditionIntfTable'

Port state condition interface table.

hm2PortMonitorConditionIntfEntry row .1.3.6.1.4.1.248.11.22.1.7.3.1.1

Port state action interface entry.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2PortMonitorConditionField

Condition type field.

Bits

Enumerated Values:

0	none
1	link-flap
2	crcFragments
3	duplexMismatch
4	overload-detection
5	speed-duplex

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.1

hm2PortMonitorConditionLinkFlapMode

Interface link flap mode.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.2

hm2PortMonitorConditionCrcFragmentsMode

Interface CrcFragments mode.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.3

hm2PortMonitorConditionDuplexMismatchDetectionMode

Interface duplex mismatch detection mode.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.4

hm2PortMonitorConditionOverloadDetectionMode

Interface Overload Detection mode.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.5

hm2PortMonitorConditionSpeedDuplexMode

Interface Speed and Duplex monitor mode.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.248.11.22.1.7.3.1.1.6

hm2PortMonitorConditionLinkFlapIntfTable

table

.1.3.6.1.4.1.248.11.22.1.7.3.2.1 · 1 row entry · 4 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorConditionLinkFlapIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorConditionLinkFlapIntfTable'

Port condition link flap interface table.

hm2PortMonitorConditionLinkFlapIntfEntry row .1.3.6.1.4.1.248.11.22.1.7.3.2.1.1

Port condition link flap interface entry.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hm2PortMonitorConditionLinkFlapInterval Measure interval in seconds (1-180s) for link flap detection.	Integer32r/w Constraints: `range: 1-180`	`.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.1`
hm2PortMonitorConditionLinkFlapCount Link flap counter (1-100).	Integer32r/w Constraints: `range: 1-100`	`.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.2`
hm2PortMonitorConditionLinkFlapCountInterval Link flap count that occured in last interval.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.3`
hm2PortMonitorConditionLinkFlapCountTotal Total link flap count.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.248.11.22.1.7.3.2.1.1.4`

hm2PortMonitorConditionCrcFragmentsIntfTable

table

.1.3.6.1.4.1.248.11.22.1.7.3.3.1 · 1 row entry · 4 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorConditionCrcFragmentsIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorConditionCrcFragmentsIntfTable'

Port condition CrcFragments interface table.

hm2PortMonitorConditionCrcFragmentsIntfEntry row .1.3.6.1.4.1.248.11.22.1.7.3.3.1.1

Port condition CrcFragments interface entry.

Indexes

IF-MIBifIndex

Column	Syntax	OID
hm2PortMonitorConditionCrcFragmentsInterval Measure interval in seconds (5-180s) for CrcFragments detection.	Integer32r/w Constraints: `range: 5-180`	`.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.1`
hm2PortMonitorConditionCrcFragmentsCount CrcFragments counter (1-1000000).	Integer32r/w Constraints: `range: 1-1000000`	`.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.2`
hm2PortMonitorConditionCrcFragmentsCountInterval CrcFragments count that occured in last interval.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.3`
hm2PortMonitorConditionCrcFragmentsCountTotal Total CrcFragments count.	SNMPv2-SMIInteger32 Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.248.11.22.1.7.3.3.1.1.4`

hm2PortMonitorConditionOvldDetIntfTable

table

.1.3.6.1.4.1.248.11.22.1.7.3.4.1 · 1 row entry · 9 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorConditionOvldDetIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorConditionOvldDetIntfTable'

Port condition overload detection interface table.

hm2PortMonitorConditionOvldDetIntfEntry row .1.3.6.1.4.1.248.11.22.1.7.3.4.1.1

Port condition overload detection interface entry.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2PortMonitorConditionOvldDetTrfcType

Overload detection condition traffic type.

Enumerationr/w

Enumerated Values:

1	all
2	bc
3	bc-mc

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.1

hm2PortMonitorConditionOvldDetTholdType

Overload detection conditon threshold type.

Enumerationr/w

Enumerated Values:

1	pps
2	kbps

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.2

hm2PortMonitorConditionOvldDetLwrTholdVal

Overload detection condition lower threshold value.

Integer32r/w

Constraints:
range: 0-10000000

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.3

hm2PortMonitorConditionOvldDetUprTholdVal

Overload detection condition upper threshold value.

Integer32r/w

Constraints:
range: 0-10000000

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.4

hm2PortMonitorConditionOvldDetIntvl

Measure interval in seconds (1-20s) for overload detection.

Integer32r/w

Constraints:
range: 1-20

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.5

hm2PortMonitorConditionOvldDetPkgCntAll

All package count from last interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.6

hm2PortMonitorConditionOvldDetPkgCntBC

Broadcast package count from last interval.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.7

hm2PortMonitorConditionOvldDetPkgCntMC

Overload detection condition lower threshold value.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.8

hm2PortMonitorConditionOvldDetPkgCntKbit

Overload detection condition lower threshold value.

SNMPv2-SMIInteger32

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.248.11.22.1.7.3.4.1.1.9

hm2PortMonitorConditionSpeedDuplexTable

table

.1.3.6.1.4.1.248.11.22.1.7.3.5.1 · 1 row entry · 1 columns

Open in standard view

Uses the hirschmann variant from /opt/observium/mibs/hirschmann.

Command help

Walk hm2PortMonitorConditionSpeedDuplexTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'HM2-DIAGNOSTIC-MIB' -M '/opt/observium/mibs/hirschmann:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'HM2-DIAGNOSTIC-MIB::hm2PortMonitorConditionSpeedDuplexTable'

Port condition speed-duplex interface table.

hm2PortMonitorConditionSpeedDuplexEntry row .1.3.6.1.4.1.248.11.22.1.7.3.5.1.1

Port condition speed-duplex interface entry.

Indexes

IF-MIBifIndex

Column Syntax OID

hm2PortMonitorConditionSpeedDuplexValue

Speed and duplex combination allowed by port-monitor.

Bitsr/w

Enumerated Values:

0	hdx-10
1	fdx-10
2	hdx-100
3	fdx-100
4	hdx-1000
5	fdx-1000
6	fdx-2500
7	fdx-10000

.1.3.6.1.4.1.248.11.22.1.7.3.5.1.1.1