GESINGLEUPS-MIB Table View

A list of input table entries.  The number of entries
is given by the value of upsInputNumLines.(*)

upsInputGenEntry row .1.3.6.1.4.1.818.1.1.10.3.3.1

An entry containing information applicable to a
particular input line.(*)

Indexes

upsInputLineIndexgen

Column	Syntax	OID
upsInputLineIndexgen The input line identifier.(*)	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.1
upsInputFrequencygen The present input frequency.(*)	0.1 HertzNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.2
upsInputVoltagegen The magnitude of the present input voltage.(*)	RMS VoltsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.3
upsInputCurrentgen The magnitude of the present input current.(*)	0.1 RMS AmpNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.4
upsInputTruePowergen The magnitude of the present input true power.(*)	WattsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.5
upsInputVoltageMingen The lowest magnitude of the input voltage since last read out.	RMS VoltsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.6
upsInputVoltageMaxgen The highest magnitude of the input voltage since last read out.	RMS VoltsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.3.3.1.7

A list of output table entries.  The number of
entries is given by the value of upsOutputNumLines.(*)

upsOutputGenEntry row .1.3.6.1.4.1.818.1.1.10.4.4.1

An entry containing information applicable to a
particular output line.(*)

Indexes

upsOutputLineIndexgen

Column	Syntax	OID
upsOutputLineIndexgen The output line identifier.(*)	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.1
upsOutputVoltagegen The present output voltage.(*)	RMS VoltsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.2
upsOutputCurrentgen The present output current.(*)	0.1 RMS AmpNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.3
upsOutputPowergen The present output true power.(*)	WattsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.4
upsOutputPercentLoadgen The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.(*)	percentInteger32 Constraints: range: 0-200	.1.3.6.1.4.1.818.1.1.10.4.4.1.5
upsOutputPowerFactorgen The present output power factor. The returned value correspond to the cosf of the load. A positive value indicate an inductive load; a negative value indicate a capacitive load; value 1 indicate a resistive load. If…	0.01 cos phiInteger32 Constraints: range: -99-100	.1.3.6.1.4.1.818.1.1.10.4.4.1.6
upsOutputPeakCurrentgen The present output peak current.(*)	AmpsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.7
upsOutputShareCurrentgen In a parallel system ideally all the UPS are requested to contribute to the load with the same amount of current, i.e. with no current share. The current share occurs when an UPS exchanges some current with another UP…	AmpsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.818.1.1.10.4.4.1.8

A list of bypass table entries.  The number of
entries is given by the value of upsBypassNumLines.(*)

upsBypassGenEntry row .1.3.6.1.4.1.818.1.1.10.5.3.1

An entry containing information applicable to a
particular bypass input.(*)

Indexes

upsBypassLineIndexgen

Column	Syntax	OID
upsBypassLineIndexgen The bypass line identifier.(*)	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.5.3.1.1
upsBypassVoltagegen The present bypass voltage.(*)	RMS VoltsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.5.3.1.2
upsBypassCurrentgen The present bypass current.(*)	0.1 RMS AmpNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.5.3.1.3
upsBypassPowergen The present true power conveyed by the bypass.(*)	WattsNonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.5.3.1.4

A list of alarm table entries.  The table contains
zero, one, or many rows at any moment, depending upon
the number of alarm conditions in effect.  The table
is initially empty at agent startup.  The agent
creates a row in the table each time a condition is
detected and deletes that row when that condition no
longer pertains.  The agent creates the first row with
upsAlarmId equal to 1, and increments the value of
upsAlarmId each time a new row is created, wrapping to
the first free value greater than or equal to 1 when
the maximum value of upsAlarmId would otherwise be
exceeded.  Consequently, after multiple operations,
the table may become sparse, e.g., containing entries
for rows 95, 100, 101, and 203 and the entries should
not be assumed to be in chronological order because
upsAlarmId might have wrapped.
          
Alarms are named by an AutonomousType (OBJECT
IDENTIFIER), upsAlarmDescr, to allow a single table to
reflect well known alarms plus alarms defined by a
particular implementation, i.e., as documented in the
private enterprise MIB definition for the device.  No
two rows will have the same value of upsAlarmDescr,
since alarms define conditions.  In order to meet this
requirement, care should be taken in the definition of
alarm conditions to insure that a system cannot enter
the same condition multiple times simultaneously.
          
The number of rows in the table at any given time is
reflected by the value of upsAlarmsPresent.(*)

upsAlarmGenEntry row .1.3.6.1.4.1.818.1.1.10.6.2.1

An entry containing information applicable to a
particular alarm.(*)

Indexes

upsAlarmIdgen

Column	Syntax	OID
upsAlarmIdgen A unique identifier for an alarm condition. This value must remain constant.(*)	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.6.2.1.1
upsAlarmDescrgen A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.(*)	SNMPv2-TCAutonomousType Description: Represents an independently extensible type identification value. It may, for example, indicate a particular sub-tree with further MIB definitions, or define a particular type of protocol or hardware.	.1.3.6.1.4.1.818.1.1.10.6.2.1.2
upsAlarmTimegen The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.(*)	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.818.1.1.10.6.2.1.3

A list of receptacle table entries.  The number of
entries is given by the value of upsReceptacleNum.

upsReceptacleGenEntry row .1.3.6.1.4.1.818.1.1.10.8.7.1

An entry containing information applicable to a
particular receptacle.

Indexes

upsReceptacleLineIndexgen

Column	Syntax	OID
upsReceptacleLineIndexgen The receptacle line identifier.	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.8.7.1.1
upsReceptacleOnOffgen The present state of the receptacle. Setting this object to 'on' will cause the receptacle to be turned on. Setting this object to 'off' will turn the receptacle off. If the receptacle is already in the desired state n…	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.818.1.1.10.8.7.1.2

A list of event table entries.  The number of entries is always
10, and the value of upsEventTableSize gives the number of valid
entries from the begging of the table.  Invalid entries return 0.
          
To prevent problems with simultaneous queries from several agents,
these values MUST be accessed using several PDUs in the
same SNMP message (<number> is (1..10)):
          
PDU-SET upsSetStartingTimeStamp <time> 
PDU-SET upsEventGetNext <number>
PDU-GET upsEventTableSize
PDU-GET upsEventCode,upsEventStatus,upsEventTime 1
PDU-GET upsEventCode,upsEventStatus,upsEventTime 2
..
PDU-GET upsEventCode,upsEventStatus,upsEventTime <number>
          
The table is read up to requested number of events and the
management software afterwards decides which entries are
valid, as indicated by the upsEventTableSize.

upsEventGenEntry row .1.3.6.1.4.1.818.1.1.10.10.6.1

An entry containing information applicable to a
particular event.

Indexes

upsEventLineIndexgen

Column	Syntax	OID
upsEventLineIndexgen The event line identifier.	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.10.6.1.1
upsEventCodegen The event code in numerical format.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.818.1.1.10.10.6.1.2
upsEventStatusgen The status of the UPS at the moment that the event was generated. The format is specified at the 'upsStatus' command. If the UPS is not able to deliver status information, then SNMPNOSUCHNAME is returned.	NonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.10.6.1.3
upsEventTimegen The timestamp of the moment the event was generated.	NonNegativeInteger32 Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.818.1.1.10.10.6.1.4

A list of parameter entries. The number of entries is always
16, and the value of upsParameterTableSize gives the number of valid
entries from the begging of the table. Invalid entries return 0.
          
To prevent problems with simultaneous queries from several agents,
these values MUST be accessed using several PDUs in the
same SNMP message (<number> is (1..16)):
          
Read sequence:
          
PDU-SET upsSetStartingAddress <addr>
PDU-SET upsParametersRead <number>
PDU-GET upsParameterTableSize
PDU-GET upsParameterValue 1
PDU-GET upsParameterValue 2
..
PDU-GET upsParameterValue <number>
          
The table is read up to requested number of events and the
management software afterwards decides which entries are
valid, as indicated by the upsParameterTableSize.
          
Write sequence:
          
PDU-SET upsSetStartingAddress <addr>
PDU-SET upsParameterValue 1
PDU-SET upsParameterValue 2
..
PDU-SET upsParameterValue <number>
PDU-SET upsParametersWrite <number>

upsParameterGenEntry row .1.3.6.1.4.1.818.1.1.10.10.11.1

An entry containing information applicable to a
particular parameter.

Indexes

upsParameterLineIndexgen

Column	Syntax	OID
upsParameterLineIndexgen The parameter line identifier.	PositiveInteger32 Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.818.1.1.10.10.11.1.1
upsParameterValuegen The parameter value in numerical format.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.818.1.1.10.10.11.1.2