e sources of power to this agent has failed.
Presumably a redundant power-supply has taken over.

e previously bad sources of power to this agent 
has come back to life without causing an agent restart.

that the value of one of the object identifiers 
(or the value of an object below that in the MIB tree) 
defined in the extremeSmartTrapRulesTable has changed, 
and hence a new entry has been created in the 
extremeSmartTrapInstanceTable. Such a trap is sent 
at most once every thirty seconds if one or more entry 
was created in the last thirty seconds.

that the value of the extremeSlotModuleState for 
the specified extremeSlotNumber has changed. 
Traps will be reported only for significant states.

discovers a new neighbor through Extreme Discovery
Protocol.

ates are received from this neighbor within
the configured timeout period and this neighbor entry is aged
out by the device.

t notification indicates that the on-board 
temperature sensor has reported a temperature that is 
outside the normal operating range (either higher than 
the maximum or lower than the minimum of the range) and 
the switch is in an overheat (or overcold) condition.

ed trap indicates one or more of the
cooling fans inside the device has failed.  A
fanOK trap will be sent once the fan has attained
normal operation.

transitioned out of a failure state and
is now operating correctly.

empted to login to console or by telnet but was
refused access due to incorrect username or password

Cpu HealthCheck has failed.

ations Rising trap generated when
extremeCpuUtilRisingThreshold is touched/crossed 
This trap is supported only in ExtremeWare.

ation Falling Trap is generated when the
extremeCpuAggregateUtilization falls below 80% of the
extremeCpuUtilRisingThreshold
This trap is supported only in ExtremeWare.

Failed processor on module has been detected.

MSM failover occurred.

 node performed a hitless MSM failover, but the 
master failed to resume normal operation within the reelect timeout.
Thus, a new master (this switch) was elected.

Committed Information Rate exceeded.

t (return to) normal notification indicates 
that the on-board tempature sensor has reported a 
temperature that has returned to within the normal 
operating range from having been in an overheat (or 
overcold) condition.  The temperature of the unit has 
sufficiently cooled to be below the maximum (or warmed 
to be above the minimum) of the normal operating range.

This Notification indicates a change in the PoE PSU for the slot.

This Notification indicates when a LACP member-port has been added to the Aggregator.

This Notification indicates when a LACP member-port has been deleted from the Aggregator.

eBgpPrefixReachedThreshold notification is generated
when the number of prefixes received over this 
peer session reaches the threshold limit.

eBgpPrefixMaxExceeded notification is generated
when the number of prefixes received over this 
peer session reaches the maximum configured limit.

will be generated, for a port on which limit-learning has been
configured,  when a new MAC address exceeding the limit is learnt on that
port.

will be generated when a MAC Address is learnt on a port on which 
it is not not authorized. This will happen when the MAC address is statically 
configured  as a 'secure mac' on some other port(s).

will be generated on a port for which lock-learning has been 
configured, when a new MAC address is learnt on that port.

will be generated when a netlogin supplicant passes 
authentication and logs in successfully into the network.

will be generated when a netlogin supplicant logs out. 
This trap is meant to notify logout event only for already 
authenticated and logged in supplicant.

will be generated upon authentication failure for a 
netlogin supplicant

will be generated on a valn for which gratuitous ARP protection has been
configured, when a gratuitous ARP does not match the internal static or secured IP<->MAC binding.

is sent by Extreme's Network Management Applications when a change
in its inventory database occurs. This trap is not send by a router or switch.

is sent by Extreme's Network Management Applications when a change 
in its Topology database occurs. This trap is not send by a router or switch.

eElrpVlanLoopDetected notification is generated
when the ELRP client detects a loop in the vlan.

eEapsStateChange notification is generated
when the EAPS domain has a state change.

eEapsFailTimerExpFlagSet notification is 
generated when the EAPS domain's fail timer expires
for the first time, while its state is not in Fail state.

eEapsFailTimerExpFlagClear notification is 
generated when the EAPS domain's Fail timer expired flag 
is cleared.

it is in Link-Down state, and it receives a 
Health-Check-Pdu from the Master indicating the ring is
Complete, it means there is some problem with the Transit
switch that has issued this trap message.

eEapsPortStatusChange notification is 
generated when an EAPS primary or secondary port changes state.

eEapsConfigChange notification is generated
when the EAPS configuration has changed.  It is sent 30 seconds 
after the first change is made to limit the number of traps sent

eEapsLastStatusChangeTime notification is generated
10 seconds after a status change occurs.  Within the 10 second period all
status changes cause extremeEapsLastStatusChange variable to be updated.
10 seconds after the first change, this trap is sent.  This is to ensure
a management station is notified that a change occured, in case the regular
traps are dropped due to be being sent while the network is converging.

eBgpPrefixReachedThreshold notification is generated
when the number of prefixes received over this 
peer session reaches the threshold limit.

eBgpPrefixMaxExceeded notification is generated
when the number of prefixes received over this 
peer session reaches the maximum configured limit.

eEapsFailTimerExpFlagSet notification is 
generated when the EAPS domain's segment timer expires
for the first time.

eEapsSegmentTimerExpFlagClear notification is 
generated when the EAPS domain's Segment Fail timer 
expired flag is cleared.

eEapsSharedPortStateChange notification is generated
when the EAPS shared port state changes.

eEapsSharedPortRootBlockerChange notification is generated
when each switch detects a new rootblocker ID on the networks.