ECS4510-MIB Table View

Table of descriptive and status information about
the switch units in this system.

switchInfoEntry row .1.3.6.1.4.1.259.10.1.24.1.1.3.1

Table providing descriptions and status information for
switch units.

Indexes

swUnitIndex

Column	Syntax	OID
swUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.1
swHardwareVer Hardware version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.2
swMicrocodeVer Microcode version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.3
swLoaderVer Loader version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.4
swBootRomVer Boot ROM code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.5
swOpCodeVer Operation code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.6
swPortNumber The number of ports on this switch.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.7
swPowerStatus Indicates the switch uses internalPower(1), redundantPower(2) or both(3)	Enumeration Enumerated Values: 1 internalPower 2 redundantPower 3 internalAndRedundantPower	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.8
swRoleInSystem Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.	Enumeration Enumerated Values: 1 master 2 backupMaster 3 slave	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.9
swSerialNumber Serial number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.10
swServiceTag Service tag serial-number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.13
swModelNumber Model number of the switch.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.14
swEpldVer The EPLD version of the switch.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.1.3.1.15

Table about the status of individual power values.

switchIndivPowerEntry row .1.3.6.1.4.1.259.10.1.24.1.1.6.1

Table about the status of individual power.

Indexes

swIndivPowerUnitIndex swIndivPowerIndex

Column	Syntax	OID
swIndivPowerUnitIndex This is defined as swUnitIndex.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.259.10.1.24.1.1.6.1.1
swIndivPowerIndex 1 means internal power, 2 means external power.	Enumeration Enumerated Values: 1 internalPower 2 externalPower	.1.3.6.1.4.1.259.10.1.24.1.1.6.1.2
swIndivPowerStatus notPresent(1) means not present, green(2) means up, red(3) means down.	Enumeration Enumerated Values: 1 notPresent 2 green 3 red	.1.3.6.1.4.1.259.10.1.24.1.1.6.1.3

The fan status table.

switchFanEntry row .1.3.6.1.4.1.259.10.1.24.1.1.9.1

A conceptual row of the switchFanTable.

Indexes

switchUnitIndex switchFanIndex

Column	Syntax	OID
switchFanStatus Indicating the status of the fan, 1:ok; 2:failure.	Enumeration Enumerated Values: 1 ok 2 failure	.1.3.6.1.4.1.259.10.1.24.1.1.9.1.3
switchFanOperSpeed The operational value of the fan speed, measured in rpm (rotations per minute).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.1.9.1.6

The table which collects switch temperature information.

switchThermalTempEntry row .1.3.6.1.4.1.259.10.1.24.1.1.11.1

A conceptual row of the switchThermalTempTable.

Indexes

switchThermalTempUnitIndex switchThermalTempThermalIndex

Column	Syntax	OID
switchThermalTempUnitIndex The unit of the switch for stackable device.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.259.10.1.24.1.1.11.1.1
switchThermalTempThermalIndex The thermal index of the switch.	Integer32 Constraints: range: 1-3	.1.3.6.1.4.1.259.10.1.24.1.1.11.1.2
switchThermalTempValue The temperature of the device in degrees Celsius.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.1.11.1.3

The table for configuring the thermal action.

switchThermalActionEntry row .1.3.6.1.4.1.259.10.1.24.1.1.12.1

A conceptual row of the switchThermalActionTable.

Indexes

switchThermalActionUnitIndex switchThermalActionThermalIndex switchThermalActionIndex

Column	Syntax	OID
switchThermalActionRisingThreshold The rising threshold of the switch temperature.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.1.12.1.4
switchThermalActionFallingThreshold The falling threshold of the switch temperature.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.1.12.1.5
switchThermalActionAction The action that will be taken when the temperature exceeds the rising threshold or falls below the falling threshold.	Bitsr/w Enumerated Values: 0 trap	.1.3.6.1.4.1.259.10.1.24.1.1.12.1.6
switchThermalActionStatus Set valid(1) to create an entry, Set Invalid(2) to delete an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.1.12.1.7

Table of descriptive and status information describing
the configuration of stacking system.

switchStackingEntry row .1.3.6.1.4.1.259.10.1.24.1.1.23.1

An entry in the table, describing the configuration of
stacking system of one unit.

Indexes

swStackingUnitIndex

Column	Syntax	OID
swStackingUnitIndex This object identifies the switch within the system for which this entry contains information.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.1
swActiveStackingButton This object identifies the active status of stacking button of the switch.	Enumeration Enumerated Values: 0 notPressed 1 pressed	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.2
swConfigStackingButton This object identifies the configured status of stacking button of the switch.	Enumerationr/w Enumerated Values: 0 notPressed 1 pressed	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.3
swMasterButton This object identifies the master button status of the switch.	Enumerationr/w Enumerated Values: 0 notPressed 1 pressed	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.4
swActiveStackingPortOption This object identifies the active option status of stacking port of the switch.	Enumeration Enumerated Values: 1 optionOne 2 optionTwo	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.5
swConfigStackingPortOption This object identifies the configured option status of stacking port of the switch.	Enumerationr/w Enumerated Values: 1 optionOne 2 optionTwo	.1.3.6.1.4.1.259.10.1.24.1.1.23.1.6

Table of descriptive and status information describing
the configuration of each switch port. This table also
contains information about each trunk.

portEntry row .1.3.6.1.4.1.259.10.1.24.1.2.1.1

An entry in the table, describing the configuration of
one switch port or trunk.

Indexes

portIndex

Column	Syntax	OID
portIndex The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.1
portName The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.2
portType Indicates the port type of the configuration of the switch.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseSfp 9 hundredBaseFxScSingleMode 10 hundredBaseFxScMultiMode 11 thousandBaseCX 12 tenG	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.3
portSpeedDpxCfg Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half…	Enumerationr/w Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 5 tx 6 rx	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.5
portCapabilities Port or trunk capabilities.	Bitsr/w Enumerated Values: 0 portCap10half 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 portCap10gHalf 7 portCap10gFull 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.6
portAutonegotiation Whether auto-negotiation is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case t…	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.8
portFlowCtrlStatus (2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently confi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.9
portTrunkIndex The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding tru…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.10
portComboForcedMode This determines the running mode of a fiber port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal…	Enumerationr/w Enumerated Values: 1 none 2 copperForced 3 copperPreferredAuto 4 reserved4 5 sfpPreferredAuto 6 sfpForced100Fx 7 sfpForced1000Sfp 8 sfpForced10gSfp	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.12
portMasterSlaveModeCfg Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.	Enumerationr/w Enumerated Values: 1 master 2 slave 3 auto 4 autoPreferMaster 5 autoPreferSlave	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.15
portMacAddrLearningStatus Set this variable to enabled(1) to start to learn MAC addresses. Set this variable to disabled(2) to stop learning MAC addresses.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.17
portMacAddrLearningCount The current number of learned MAC addresses.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.2.1.1.18

Table for cable diagnostics result.

cableDiagResultEntry row .1.3.6.1.4.1.259.10.1.24.1.2.3.2.1

Entry for cable diagnostics result.

Indexes

cableDiagResultIfIndex

Column	Syntax	OID
cableDiagResultIfIndex This is defined as the ifIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.1
cableDiagResultStatusPairA The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Val…	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 7 unknown 8 impedanceMismatch 9 failed 10 notSupported 11 noCable 12 underTesting	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.2
cableDiagResultStatusPairB The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Val…	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 7 unknown 8 impedanceMismatch 9 failed 10 notSupported 11 noCable 12 underTesting	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.3
cableDiagResultStatusPairC The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Val…	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 7 unknown 8 impedanceMismatch 9 failed 10 notSupported 11 noCable 12 underTesting	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.4
cableDiagResultStatusPairD The result of cable diagnostics. Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack of continuity between pins at each end of the pair. Val…	Enumeration Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 7 unknown 8 impedanceMismatch 9 failed 10 notSupported 11 noCable 12 underTesting	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.5
cableDiagResultDistancePairA Displays the fault distance of pair A of the cable in meters. 0 will be displayed if cableDiagResultStatusPairA equals to Value underTesting(12).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.6
cableDiagResultDistancePairB Displays the fault distance of pair B of the cable in meters. 0 will be displayed if cableDiagResultStatusPairB equals to Value underTesting(12).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.7
cableDiagResultDistancePairC Displays the fault distance of pair C of the cable in meters. 0 will be displayed if cableDiagResultStatusPairC equals to Value underTesting(12).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.8
cableDiagResultDistancePairD Displays the fault distance of pair D of the cable in meters. 0 will be displayed if cableDiagResultStatusPairD equals to Value underTesting(12).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.9
cableDiagResultTime Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.2.3.2.1.11

Table for internal loopback test result.

loopInternalResultEntry row .1.3.6.1.4.1.259.10.1.24.1.2.4.2.1

Entry for internal loopback test result.

Indexes

loopInternalResultIfIndex

Column	Syntax	OID
loopInternalResultIfIndex This is defined as the ifIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.4.2.1.1
loopInternalResultStatus The result of internal loopback.	Enumeration Enumerated Values: 1 notTestedYet 2 succeeded 3 failed	.1.3.6.1.4.1.259.10.1.24.1.2.4.2.1.2
loopInternalResultTime Displays the last time of internal loopback. For example, 'Jan 1 02:03:04 2002'.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.24.1.2.4.2.1.3

Dispalys port utilization during recent 300 seconds.

portUtilEntry row .1.3.6.1.4.1.259.10.1.24.1.2.6.1

Dispalys port utilization during recent 300 seconds.

Indexes

portUtilIfIndex

Column	Syntax	OID
portUtilIfIndex The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.1
portInOctetRate The input octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.2
portInPacketRate The input packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.3
portInUtil The input utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.4
portOutOctetRate The output octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.5
portOutPacketRate The output packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.6
portOutUtil The output utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.6.1.7

Configures vlan trunking feature.

portVlanTrunkingEntry row .1.3.6.1.4.1.259.10.1.24.1.2.7.1

Configures vlan trunking feature.

Indexes

portVlanTrunkingIfIndex

Column	Syntax	OID
portVlanTrunkingIfIndex The port and trunk interface of the portVlanTrunkingTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.7.1.1
portVlanTrunkingStatus Whether vlan trunking is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.2.7.1.2

This table lists the information of the media device
(SFP/XFP/Copper) installed in the physical port.
Only the ifIndices of Ethernet ports associated
with the operational cards will be included in this table.

portMediaInfoEntry row .1.3.6.1.4.1.259.10.1.24.1.2.10.1

An entry in the Interface Media Information table.
The ifIndices of ethernet interfaces will be used
to index this table.

Indexes

portMediaInfoIfIndex

Column	Syntax	OID
portMediaInfoIfIndex ifindex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.1
portMediaInfoConnectorType The connector type.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.2
portMediaInfoFiberType The fiber type.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.3
portMediaInfoEthComplianceCodes The ethernet compliance codes.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.4
portMediaInfoBaudRate The baud rate.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.5
portMediaInfoVendorOUI The OUI of the vendor.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.6
portMediaInfoVendorName The media vendor name, full name of the corporation.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.7
portMediaInfoPartNumber The media vendor part number.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.8
portMediaInfoRevision The media vendor product version number.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.9
portMediaInfoSerialNumber The vendor serial number of the media device.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.10
portMediaInfoDateCode The date code of the media device.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.2.10.1.11

This table lists the instrumented parameters of all
optical interfaces.

portOpticalMonitoringInfoEntry row .1.3.6.1.4.1.259.10.1.24.1.2.11.1

Only the ifIndices of optical interfaces
whose parameters need to be monitored will
be used to index this table.

Indexes

portOpticalMonitoringInfoIfIndex

Column	Syntax	OID
portOpticalMonitoringInfoIfIndex ifindex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.1
portOpticalMonitoringInfoTemperature This object holds the value of the transmitter laser diode temperature for the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius). If the device supports ALARM WARNING TRAP…	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.2
portOpticalMonitoringInfoVcc This object holds the value of the Vcc. It is measured in V. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.3
portOpticalMonitoringInfoTxBiasCurrent Tx Bias Current. It is measured in mA. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.4
portOpticalMonitoringInfoTxPower This object holds the value of the transmitter optical signal power for the interface, measured in dBm. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or…	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.5
portOpticalMonitoringInfoRxPower This object holds the value of the receiver optical signal power for the interface, measured in dBm. If the device support ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or hig…	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.24.1.2.11.1.6

This table lists the threshold of transceivers.

portTransceiverThresholdInfoEntry row .1.3.6.1.4.1.259.10.1.24.1.2.12.1

Identify the index of the transceiver

Indexes

portTransceiverThresholdInfoIfIndex

Column	Syntax	OID
portTransceiverThresholdInfoIfIndex ifindex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.1
portTransceiverThresholdInfoTemperatureLowAlarm This object holds the low alarm threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.2
portTransceiverThresholdInfoTemperatureLowWarn This object holds the low warning threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.3
portTransceiverThresholdInfoTemperatureHighWarn This object holds the high warning threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.4
portTransceiverThresholdInfoTemperatureHighAlarm This object holds the high alarm threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.5
portTransceiverThresholdInfoVccLowAlarm This object holds the low alarm threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.6
portTransceiverThresholdInfoVccLowWarn This object holds the low warning threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.7
portTransceiverThresholdInfoVccHighWarn This object holds the high warning threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.8
portTransceiverThresholdInfoVccHighAlarm This object holds the high alarm threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.9
portTransceiverThresholdInfoTxBiasCurrentLowAlarm low alarm threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.10
portTransceiverThresholdInfoTxBiasCurrentLowWarn low warning threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.11
portTransceiverThresholdInfoTxBiasCurrentHighWarn high warning threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.12
portTransceiverThresholdInfoTxBiasCurrentHighAlarm high alarm threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.13
portTransceiverThresholdInfoTxPowerLowAlarm This object holds the low alarm threshold of the transmitter optical signal power for theinterface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.14
portTransceiverThresholdInfoTxPowerLowWarn This object holds the low warning threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.15
portTransceiverThresholdInfoTxPowerHighWarn This object holds the high warning threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.16
portTransceiverThresholdInfoTxPowerHighAlarm This object holds the high alarm threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.17
portTransceiverThresholdInfoRxPowerLowAlarm This object holds the low alarm threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.18
portTransceiverThresholdInfoRxPowerLowWarn This object holds the low warning threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.19
portTransceiverThresholdInfoRxPowerHighWarn This object holds the high warning threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.20
portTransceiverThresholdInfoRxPowerHighAlarm This object holds the high alarm threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.21
portTransceiverThresholdAutoMode Indicates the transceiver threshold is retrieved from EEPROM or configured by user.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.2.12.1.22

Table describing the configuration and status of each
trunk.

trunkEntry row .1.3.6.1.4.1.259.10.1.24.1.3.3.1

An entry describing the configuration and status of a
particular trunk.

Indexes

trunkIndex

Column	Syntax	OID
trunkIndex Identifies the trunk within the switch that is described by the table entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.3.3.1.1
trunkPorts The complete set of ports currently associated with this trunk.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.3.3.1.2
trunkCreation A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.	Enumeration Enumerated Values: 1 static 2 lacp	.1.3.6.1.4.1.259.10.1.24.1.3.3.1.3
trunkStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.3.3.1.4

Table for LACP port configuration.

lacpPortEntry row .1.3.6.1.4.1.259.10.1.24.1.4.1.1

Entry for LACP port configuration. While an entry may
exist for a particular port, the port may not support
LACP and an attempt to enable LACP may result in
failure.

Indexes

lacpPortIndex

Column	Syntax	OID
lacpPortIndex The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.4.1.1.1
lacpPortStatus Whether 802.3ad LACP is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.4.1.1.2

The table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType.

staPortEntry row .1.3.6.1.4.1.259.10.1.24.1.5.2.1

The conceptual entry of staPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
staPortProtocolMigration When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.3
staPortOperEdgePort The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.5
staPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.6
staPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-de…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.7
staPortSystemStatus Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.9
staPortLongAdminPathCost The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This obje…	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.10
staPortLongOperPathCost The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This objec…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.11
staPortBpduFlooding This parameter is used to configure the capability of BPDU flooding.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.12
staPortBpduGuard A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.15
staPortAdminEdgePortWithAuto The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port a…	Enumerationr/w Enumerated Values: 1 true 2 false 3 auto	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.16
staPortBpduFilter The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid trans…	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.17
staPortRootGuardStatus Specifies the desired status of root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.18
staPortBpduGuardAutoRecovery A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.19
staPortBpduGuardAutoRecoveryInterval The interval in seconds used by BPDU guard auto recovery mechanism.	Unsigned32r/w Constraints: range: 30-86400	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.20
staPortTcPropStop Stop topology change propogate on this ifindex. Don't enable on potential ring port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.5.2.1.21

This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0.

xstInstanceCfgEntry row .1.3.6.1.4.1.259.10.1.24.1.5.6.4.1

A conceptual row containing the property of the RST or MST instance.

Indexes

xstInstanceCfgIndex

Column	Syntax	OID
xstInstanceCfgIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.1
xstInstanceCfgPriority The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.2
xstInstanceCfgTimeSinceTopologyChange The time (in hundredths of a second) since the last topology change was detected by the bridge entity in RST or MST.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.3
xstInstanceCfgTopChanges The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.4
xstInstanceCfgDesignatedRoot The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identi…	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.5
xstInstanceCfgRootCost The cost of the path to the root as seen from this bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.6
xstInstanceCfgRootPort The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.7
xstInstanceCfgMaxAge The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is t…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.8
xstInstanceCfgHelloTime The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.9
xstInstanceCfgHoldTime This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.10
xstInstanceCfgForwardDelay For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the por…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.11
xstInstanceCfgBridgeMaxAge For RST or MST protocol, the time (in hundredths of a second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the v…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.12
xstInstanceCfgBridgeHelloTime For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.13
xstInstanceCfgBridgeForwardDelay For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.14
xstInstanceCfgTxHoldCount For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.15
xstInstanceCfgPathCostMethod For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value o…	StaPathCostMode Type Values: 1 short 2 long	.1.3.6.1.4.1.259.10.1.24.1.5.6.4.1.16

The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration.

xstInstancePortEntry row .1.3.6.1.4.1.259.10.1.24.1.5.6.5.1

The conceptual row for xstInstancePortTable.

Indexes

xstInstanceCfgIndex BRIDGE-MIBdot1dStpPort

Column	Syntax	OID
xstInstancePortPriority Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active lin…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.3
xstInstancePortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, …	Enumeration Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.4
xstInstancePortEnable The enabled/disabled status of the port.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.5
xstInstancePortDesignatedRoot The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.7
xstInstancePortDesignatedCost The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.8
xstInstancePortDesignatedBridge The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.9
xstInstancePortDesignatedPort The port identifier of the port on the designated bridge for this port's segment.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.10
xstInstancePortForwardTransitions The number of times this port has transitioned from the learning state to the forwarding state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.11
xstInstancePortPortRole The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port …	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup 6 master	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.12
xstInstancePortAdminPathCost The admin value of the MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster med…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.13
xstInstancePortOperPathCost The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attache…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.10.1.24.1.5.6.5.1.14

The Multiple Spanning Tree region instance vlan configuration table.
Please read the actual instance vlan mapped in the mstInstanceOperTable.

mstInstanceEditEntry row .1.3.6.1.4.1.259.10.1.24.1.5.6.6.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceEditIndex

Column	Syntax	OID
mstInstanceEditIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.1
mstInstanceEditVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.2
mstInstanceEditVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.3
mstInstanceEditVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.4
mstInstanceEditVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.5
mstInstanceEditRemainingHops The remaining hop count for this MST instance.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.5.6.6.1.6

The Multiple Spanning Tree region instance vlan mapped table.

mstInstanceOperEntry row .1.3.6.1.4.1.259.10.1.24.1.5.6.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceOperIndex

Column	Syntax	OID
mstInstanceOperIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.10.1.24.1.5.6.7.1.1
mstInstanceOperVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.7.1.2
mstInstanceOperVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.7.1.3
mstInstanceOperVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.7.1.4
mstInstanceOperVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.24.1.5.6.7.1.5

A table providing the mechanism to configure the
spanning tree loopback detection of each port or trunk

staLoopbackDetectionPortEntry row .1.3.6.1.4.1.259.10.1.24.1.5.8.1

A conceptual row of staLoopbackDetectionPortTable.

Indexes

staLoopbackDetectionPortIfIndex

Column	Syntax	OID
staLoopbackDetectionPortIfIndex The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.24.1.5.8.1.1
staLoopbackDetectionPortStatus Status of the port on whether spanning tree loopback detection is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.8.1.2
staLoopbackDetectionPortTrapStatus The parameter indicates whether the trap has to be sent when loopback BPDUs have been detected.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.5.8.1.3
staLoopbackDetectionPortReleaseMode Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manu…	Enumerationr/w Enumerated Values: 1 auto 2 manual	.1.3.6.1.4.1.259.10.1.24.1.5.8.1.4
staLoopbackDetectionPortRelease Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.	Enumerationr/w Enumerated Values: 1 noRelease 2 release	.1.3.6.1.4.1.259.10.1.24.1.5.8.1.5

Table describing the configuration of each TC propagation group.

staTcPropGroupEntry row .1.3.6.1.4.1.259.10.1.24.1.5.10.1

An entry describing the configuration of a particular TC propagation group.

Indexes

staTcPropGroupIndex

Column	Syntax	OID
staTcPropGroupIndex Identifies the TC propagation group within the switch that is described by the table entry.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.259.10.1.24.1.5.10.1.1
staTcPropGroupPorts The complete set of ports currently associated with this TC propagation group. A port can only belong to one group. If a port detects a topology change, this port only notifies other ports in the same group to propagate…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.5.10.1.2

Table for port mirroring, enabling a port to be mirrored
to/from another port. Not all ports can be mirrored and
limitations may apply as to which ports can be used as either
source or destination ports.

mirrorEntry row .1.3.6.1.4.1.259.10.1.24.1.8.1.1

The conceptual row of mirrorTable.

Indexes

mirrorDestinationPort mirrorSourcePort

Column	Syntax	OID
mirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.1.1.1
mirrorSourcePort The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.1.1.2
mirrorType If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.	Enumerationr/w Enumerated Values: 1 rx 2 tx 3 both	.1.3.6.1.4.1.259.10.1.24.1.8.1.1.3
mirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.8.1.1.4

Table for VLAN mirroring, enabling a VLAN to be mirrored
to a port.

vlanMirrorEntry row .1.3.6.1.4.1.259.10.1.24.1.8.2.1

The conceptual row of vlanMirrorTable.

Indexes

vlanMirrorDestinationPort vlanMirrorSourceVlan

Column	Syntax	OID
vlanMirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.2.1.1
vlanMirrorSourceVlan The source VLAN for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.2.1.2
vlanMirrorStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.8.2.1.4

A table that contains the settings of RSPAN.

rspanEntry row .1.3.6.1.4.1.259.10.1.24.1.8.3.1

The conceptual row of rspanTable.

Indexes

rspanSessionId

Column	Syntax	OID
rspanSessionId The session ID that may specify an entry in the table which contains destination port(s) information.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.1
rspanSrcTxPorts Specifies the source port list in tx mode.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.2
rspanSrcRxPorts Specifies the source port list in rx mode.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.3
rspanDstPort The port number of a destination port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.4
rspanDstPortTag Specifies the traffic which is sent out from source port with RSPAN VLAN ID or not.	Enumerationr/w Enumerated Values: 1 none 2 untagged 3 tagged	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.5
rspanSwitchRole Specifies the role of current switch.	Enumerationr/w Enumerated Values: 1 none 2 source 3 intermediate 4 destination	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.6
rspanRemotePorts Specifies the uplink port list.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.7
rspanRemoteVlanId Specifies the ID of a RSPAN VLAN.	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.8
rspanOperStatus The operational status of the entry. A status of up(1) means the setting of a session is complete and it has started performing its function. A status of down(2) means no function is performed because of incompleted ses…	Enumeration Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.9
rspanStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.8.3.1.10

Table for MAC mirroring, enabling a MAC address to be
mirrored to a port.

macMirrorEntry row .1.3.6.1.4.1.259.10.1.24.1.8.4.1

The conceptual row of mirrorMacTable.

Indexes

macMirrorDestinationPort macMirrorSourceMacAddr

Column	Syntax	OID
macMirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.8.4.1.1
macMirrorSourceMacAddr Packets with matching source MAC address will be monitored.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.259.10.1.24.1.8.4.1.2
macMirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.8.4.1.3

Table for current router ports.

igmpSnoopRouterCurrentEntry row .1.3.6.1.4.1.259.10.1.24.1.9.8.1

Entry for current router ports.

Indexes

igmpSnoopRouterCurrentVlanIndex

Column	Syntax	OID
igmpSnoopRouterCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.8.1.1
igmpSnoopRouterCurrentPorts The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.8.1.2
igmpSnoopRouterCurrentStatus The set of ports which are static router ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.8.1.3

Table for static router ports.

igmpSnoopRouterStaticEntry row .1.3.6.1.4.1.259.10.1.24.1.9.9.1

Entry for static router ports.

Indexes

igmpSnoopRouterStaticVlanIndex

Column	Syntax	OID
igmpSnoopRouterStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.9.1.1
igmpSnoopRouterStaticPorts The set of ports which are static router ports.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.9.9.1.2
igmpSnoopRouterStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.9.9.1.3

Table for current multicast addresses.

igmpSnoopMulticastCurrentEntry row .1.3.6.1.4.1.259.10.1.24.1.9.10.1

Entry for current multicast addresses.

Indexes

igmpSnoopMulticastCurrentVlanIndex igmpSnoopMulticastCurrentIpAddress

Column	Syntax	OID
igmpSnoopMulticastCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.10.1.1
igmpSnoopMulticastCurrentIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.24.1.9.10.1.2
igmpSnoopMulticastCurrentPorts The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.10.1.3
igmpSnoopMulticastCurrentStatus The set of ports which are static members.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.10.1.4

Table for static multicast addresses.

igmpSnoopMulticastStaticEntry row .1.3.6.1.4.1.259.10.1.24.1.9.11.1

Entry for static multicast addresses.

Indexes

igmpSnoopMulticastStaticVlanIndex igmpSnoopMulticastStaticIpAddress

Column	Syntax	OID
igmpSnoopMulticastStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.11.1.1
igmpSnoopMulticastStaticIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.24.1.9.11.1.2
igmpSnoopMulticastStaticPorts The set of ports which are members.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.24.1.9.11.1.3
igmpSnoopMulticastStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.9.11.1.4

Table for enabling or disabling IGMP snooping per VLAN.

igmpSnoopCurrentVlanEntry row .1.3.6.1.4.1.259.10.1.24.1.9.14.1

Entry for enabling or disabling IGMP snooping.

Indexes

igmpSnoopCurrentVlanIndex

Column	Syntax	OID
igmpSnoopCurrentVlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.1
igmpSnoopCurrentVlanStatus Parameter to enable or disable IGMP snooping on this VLAN. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.2
igmpSnoopCurrentVlanImmediateLeave The parameter to enable or disable the Immediate-Leave feature on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.3
igmpSnoopCurrentVlanGeneralQuerySuppression The parameter to enable or disable general query suppresion on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.4
igmpSnoopCurrentVlanLastMemQueryCount Represents the number of queries sent by the switch before it assumes there are no local members.	Unsigned32r/w Constraints: range: 1-255	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.5
igmpSnoopCurrentVlanLastMemQueryIntvl The last member query interval is the max response time inserted into group-specific queries sent in response to leave group messages,and is also the the max response time inserted into group-and-source-specific query m…	Unsigned32r/w Constraints: range: 1-31744	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.6
igmpSnoopCurrentVlanProxyAddress Represents the address of queries sent by the switch.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.7
igmpSnoopCurrentVlanQueryIntvl Represents the query interval of queries sent by the switch.	Unsigned32r/w Constraints: range: 2-31744	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.8
igmpSnoopCurrentVlanQueryRespIntvl Represents the query response interval of queries sent by the switch.	Unsigned32r/w Constraints: range: 10-31740	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.9
igmpSnoopCurrentVlanProxyReporting Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(3), the status of the feature is decided by the global configuration.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 3 default	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.10
igmpSnoopCurrentVlanVersion The version of igmp packets supported by this vlan.	Unsigned32r/w Constraints: range: 1-3	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.11
igmpSnoopCurrentVlanVersionExclusive Enable/disable control of the IGMP Snooping exclusive supported version.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.12
igmpSnoopCurrentVlanReportSupression Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(0), the status of the feature is decided by the global configuration.	Enumerationr/w Enumerated Values: 0 default 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.13
igmpSnoopCurrentVlanImmediateLeaveByHostIp The parameter to enable or disable the Immediate-Leave feature by host ip on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.24.1.9.14.1.14

Table for current multicast addresses.

igmpSnoopMulticastGroupEntry row .1.3.6.1.4.1.259.10.1.24.1.9.15.1

Entry for Group multicast addresses.

Indexes

igmpSnoopMulticastGroupVlanIndex igmpSnoopMulticastGroupIpAddress igmpSnoopMulticastGroupSourceIPAddress

Column	Syntax	OID
igmpSnoopMulticastGroupVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.259.10.1.24.1.9.15.1.1
igmpSnoopMulticastGroupIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.24.1.9.15.1.2
igmpSnoopMulticastGroupSourceIPAddress Source IP address of source.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.24.1.9.15.1.3
igmpSnoopMulticastGroupPorts The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.15.1.4
igmpSnoopMulticastGroupStatus The set of ports which are static IGMP member ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.24.1.9.15.1.5

The table for configuring the IGMP snooping profile.

igmpSnoopProfileEntry row .1.3.6.1.4.1.259.10.1.24.1.9.18.1

The entry for configuring the IGMP snooping profile.

Indexes

igmpSnoopProfileId

Column	Syntax	OID
igmpSnoopProfileId The ID of the IGMP snooping profile.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.18.1.1
igmpSnoopProfileAction The access mode of the IGMP snooping profile.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.10.1.24.1.9.18.1.2
igmpSnoopProfileStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.24.1.9.18.1.3

The table for configuring the range of the IGMP snooping
profile.

igmpSnoopProfileRangeEntry row .1.3.6.1.4.1.259.10.1.24.1.9.20.1

The entry for configuring the range of the IGMP snooping
profile.

Indexes

igmpSnoopProfileRangeProfileId igmpSnoopProfileRangeInetAddressType igmpSnoopProfileRangeStartInetAddress

Column	Syntax	OID
igmpSnoopProfileRangeProfileId This is defined as igmpSnoopProfileId.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.20.1.1
igmpSnoopProfileRangeInetAddressType The address type associated with this agent. Only ipv4(1) type is supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.259.10.1.24.1.9.20.1.2
igmpSnoopProfileRangeStartInetAddress The specified addresses in the start of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.10.1.24.1.9.20.1.3
igmpSnoopProfileRangeEndInetAddress The specified addresses in the end of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.10.1.24.1.9.20.1.4
igmpSnoopProfileRangeAction The access mode of the IGMP snooping profile.	Enumeration Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.10.1.24.1.9.20.1.5

Table for port configuration in IGMP filtering.

igmpSnoopFilterPortEntry row .1.3.6.1.4.1.259.10.1.24.1.9.21.1

Entry for port configuration in IGMP filtering.

Indexes

igmpSnoopFilterPortIndex

Column	Syntax	OID
igmpSnoopFilterPortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.21.1.1
igmpSnoopFilterPortProfileId The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTab…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.9.21.1.2

Table for port configuration in IGMP throttling.

igmpSnoopThrottlePortEntry row .1.3.6.1.4.1.259.10.1.24.1.9.22.1

Entry for port configuration in IGMP throttling.

Indexes

igmpSnoopThrottlePortIndex

Column	Syntax	OID
igmpSnoopThrottlePortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.24.1.9.22.1.1
igmpSnoopThrottlePortRunningStatus Describes the running status of IGMP throttling on the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.24.1.9.22.1.2
igmpSnoopThrottlePortAction The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to th…	Enumerationr/w Enumerated Values: 1 replace 2 deny	.1.3.6.1.4.1.259.10.1.24.1.9.22.1.3
igmpSnoopThrottlePortMaxGroups The maximum number of IGMP groups that the interface can join.	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.259.10.1.24.1.9.22.1.4
igmpSnoopThrottlePortCurrentGroups The current number of IGMP groups that the interface has joined.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.24.1.9.22.1.5