Dell-LAN-TRAP-MIB

Indicates that an invalid user tries to login to the CLI or Web.
The dellTrapSource should indicate the unit member ID and the
dellTrapInfo should indicate whether the login attempt is on the
CLI or Web and the IP address from which the attempt was made.

Indicates that an SNMP request or CLI/Web access request was
received but does not meet the management ACL rules. For example,
if the request comes from an invalid IP address or has the wrong
SNMP community string (for V1/2c) or is not authenticated for
SNMPv3, etc. The dellTrapSource should indicate the unit # and
the dellTrapInfo should indicate which interface (web, cli, snmp)
is violated and the source IP address of the request.

Indicates that an SFP was inserted into the system.
The dellTrapSource should indicate the unit # and
the dellTrapInfo should indicate on which interface
was the SFP inserted.

Indicates that an SFP was removed from the system.
The dellTrapSource should indicate the unit # and
the dellTrapInfo should indicate from which interface
was the SFP removed.

Indicates that an XFP was inserted into the system.
The dellTrapSource should indicate the unit # and
the dellTrapInfo should indicate on which interface
was the XFP inserted.

Indicates that an XFP was removed from the system.
The dellTrapSource should indicate the unit # and
the dellTrapInfo should indicate from which interface
was the XFP removed.

Indicates that a switch hardware resource overflowed. The
dellTrapSource should indicate the unit number whereas dellTrapInfo
should identify the resource that overflowed.

Indicates that a switch software resource overflowed. The
dellTrapSource should indicate the unit number whereas dellTrapInfo
should identify the resource that overflowed (e.g. maximum
VLAN/LAG/MACs/IPs exceeded).

Indicates that the switch configuration has changed. The
dellTrapSource should indicate the source of the change such
as the unit, slot, port, VLAN, LAG, etc. The dellTrapInfo
may indicate additional information regarding the change.

This trap indicates that in order to perform the last SET request,
a reset operation of the router/bridge is required. This may occur
for any number of reasons such as if the change affects the routing
protocols to be switched from SPF to STP. This trap warns the user
to manually reset the switch using either physical or software reset.

This trap indicates that the device finished a TFTP
transaction with the management station. The dellTrapInfo field
will provide TFTP exit code and name/type of the file being
transferred.

This trap indicates that in the device aborted a TFTP session with
the management station. The dellTrapInfo field will provide TFTP
exit code and name/type of the file being transferred.

Informational trap indicating that the device has intiated a
TFTP session. dellTrapInfo will contain the name/type of the file
being transferred.

Link failure detected, no backup available. The dellTrapSource
should indicate the fail link.

Automantic switchover to backup link because of main link fault.
The dellTrapSource indicates the backup link coming on, and the
dellTrapInfo indicates the failed link.

Communication returned to main link. The dellTrapSource indicates
the main link coming up, and the dellTrapInfo indicates the backup
link.

This trap indicates that the an error occured during initialization
phase of the switch. Additional information is provided in the
dellTrapInfo field.

Indicates that a port was dynamically added to the VLAN. The
dellTrapSource will indicate the VLAN, and the dellTrapInfo will
indicate the port being added.

Indicates that a port was dynamically removed from a VLAN. The
dellTrapSource will indicate the VLAN, and the dellTrapInfo will
indicate the port being removed.

The requested static connection was not accepted because there is
no available IP virtual address to allocate to it.

The virtual IP address appeared as a source IP. All the connections
using it will be deleted and it will not be further allocated to
new connections.

The source IP address sent an ARP specifying a virtual IP which
was not allocated for this source. This virtual IP will not be
allocated to connections of this specific source IP.

Indicates that the stack master unit has failed. This trap is
generated by the new master when it takes over the stack. The
dellTrapSource should be the new master unit #, and the
dellTrapInfo should identify the old master unit #.

Indicates when a new master has been elected. This is different
from a stack failure in that the master has not failed but for
some reason a new master has been elected (e.g. the user requested
a new master. The trap should be generated by the new master.
the dellTrapSource should identify the new master, and the
dellTrapInfo should identify the old master.

Indicates that a member of the stack has failed. This condition
is detected by the master unit so the dellTrapSource should indicate
the master unit ID and the dellTrapInfo should indicate the
member unit that failed.

Indicates that a new member unit has been added to the stack.
This trap is generated by the master unit so the dellTrapSource
should indicate the master unit ID, and the dellTrapInfo should
identify the new unit ID.

Indicates that a member unit has been removed from the stack.
The dellTrapSource indicates the master unit ID and the
dellTrapInfo indicates the unit ID being removed.

Indicates that the stack has split into two distinct stacks which
means that each stack may end up with its own master temporarily
until the stack is rejoined. This is possibly different from the
stackMemberUnitFailed trap, which indicates only a single unit
failure. This trap indicates that the master has lost track of
part of the stack membership so that the other units may elect
their own master. The dellTrapSource should indicate the master
unit ID and the dellTrapInfo should identify the units that are
split from the main stack.

Indicates that the stack has split into two distinct stacks which
means that each stack may end up with its own master temporarily
until the stack is rejoined. This trap is generated by the new
master unit elected in the split sub-stack. The dellTrapSource
should identify the new master unit ID, and the dellTrapInfo should
identify the old master unit ID before the split occured.

Indicates that previously split stack has rejoined. The rejoined
stack will elect a master and this trap should be generated by the
elected master. The dellTrapSource should indicate the master unit
ID and the dellTrapInfo should list the unit IDs of the members.

Indicates a failure in one of the stacking link. If this stack
was connected in a ring, then the failure of a stacking link
results in a chain stack instead of a ring. Another failure
in the chain topology would result in a split stack. If the
stack is connected in a meshed or star topology then multiple
link failure may be tolerated. This trap may be generated by
any unit within the stack and must indicate the source of the
failure. The dellTrapSource should identify one end of the link
where the failure is detected. The dellTrapInfo may provide
additional information about the failure.

DHCP failed to allocate an IP address to a requesting host
because of memory shortage or inadequate configuration of
available IP addresses.

The trap is sent by a bridge when any of its configured ports
transitions from the Learning state to the Forwarding state.

The trap is sent by a bridge when any of its configured ports
transitions from the Forwarding state to the Blocking state.

Indicates that the packet drop due to the policy. This trap
may result in a huge number of trap packets and should be used
only for debugging purposes. The number of traps sent per
time period is user configurable and the user may enable/disable
generation of this trap.

Indicates that the packet has forward based on policy. The number
of traps sent per time period is user configurable and the user
may enable/disable generation of this trap.

An IGMP Message of v1 received on a given interface. The
dellTrapSource should indicate the interface.

One or more VRRP entries deleted due to IP interface deletion or
transition.

Informational trap indicating that a port is added to a trunk.
The dellTrapSource should indicate the trunk to which the port
is added. The dellTrapInfo should indicate the port being added.

This warning is generated when a port removed from a trunk.
The dellTrapSource should indicate the trunk from which the port
is removed. The dellTrapInfo should indicate the port being
removed.

Informational trap indicating that a port that is blocked from
MAC learning has receive a frame with new source Mac Address.
The dellTrapSource should identify the port and the dellTrapInfo
should specify the new MAC address received.

Indicates that a dynamic VLAN has been added via GVRP. The
dellTrapSource should identify the VLAN being added.

Indicates that a dynamic VLAN has been removed via GVRP. The
dellTrapSource should identify the VLAN being removed.

Indicates that a dynamic VLAN has been made static. The
dellTrapSource should identify the VLAN.

Indicates that a static VLAN has been made dynamic. The
dellTrapSource should identify the VLAN.

Trap indicating the fan state. The dellTrapSource should identify
the exact fan index if there are multiple fans. The dellTrapInfo
may provide additional info relating to the fan new state.

Trap indicating the power supply state. The dellTrapSource should
identify the exact power supply. The dellTrapInfo may provide
additional info regarding the power state.

Trap indicating that the temperature in the device has exceeded the
device specific safe temperature threshold.

Informational trap indicating that the device has finished
a copy operation successfully.

Informational trap indicating that the copy operation has failed.

Informational trap indicating that port 802.1x status is authorized.

Warning trap is indicating that port 802.1x status is unAuthorized.

Indicates that a broadcast storm has been detected. The
dellTrapSource should indicate the port on which the broadcast
storm is detected.

Indicates that the switch has been elected as the new STP root.

Indicates that a new root has been elected. The dellTrapSource
should indicate the member unit number and the dellTrapInfo should
provide information on the new root.

Indicates that this switch has been elected as the new IGMP
snooping querier.