DGS3224-SWL3MGMT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
3
Rows
3
Columns
35
.1.3.6.1.4.1.171.11.101.3.3.2.1.3 · 1 row entry · 14 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3IpCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3224-SWL3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3224-SWL3MGMT-MIB::swL3IpCtrlTable'
This table contains IP interface information.
swL3IpCtrlEntry row .1.3.6.1.4.1.171.11.101.3.3.2.1.3.1
A list of information about a specific IP interface.
Column Syntax OID
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.1
This object uniquely identifies the IP interface number in the
swL3IpCtrlTable.
Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.2
The IP address of the interface. This object only can take the
value of the unicast IP address.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.3
The IP net mask for this interface.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.4
This object indicates the IP control entry's VLAN name. The
VLAN name in each entry must be unique in the IP Control Table.
OctetStringr/w
Constraints:
range: 0-32
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.5
This object indicates the IP operation mode.

other(1) - This entry is currently in use but the conditions under
which it will remain are determined by each of the following values.
bootp(3) - The I…
Enumerationr/w
Enumerated Values:
1other
3bootp
4dhcp
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.8
The state of the IP interface.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.9
The IPv6 link local address for this interface.
Ipv6Address
Type Constraints:
range: 16
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.14
The IPv6 prefix length for this IPv6 link local address.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.15
This variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.16
The state of the IPv6 link local auto.
Enumerationr/w
Enumerated Values:
1other
2enabled
3disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.17
The object indicates the state of the DHCPv6 client.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.20
Enable or disable insertion of option 12 in the DHCPDISCOVER and
DHCPREQUEST message.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.22
Specify the host name to be inserted in the DHCPDISCOVER and
DHCPREQUEST message. The specified host name must start with a
letter, end with a letter or digit, and have only letters, digits,
and hyphen as interior ch…
OctetStringr/w
Constraints:
range: 0-63
.1.3.6.1.4.1.171.11.101.3.3.2.1.3.1.23
.1.3.6.1.4.1.171.11.101.3.3.2.1.4 · 1 row entry · 12 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3Ipv6CtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3224-SWL3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3224-SWL3MGMT-MIB::swL3Ipv6CtrlTable'
This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry row .1.3.6.1.4.1.171.11.101.3.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Column Syntax OID
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.1
Maximum Reassembly Size of the IP interface.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.2
Neighbor solicitation's retransmit timer.
The unit is set in milliseconds.
Unsigned32r/w
Constraints:
range: 0-4294967295
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.3
Neighbor solicited state.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.5
The minimum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInt…
Integer32r/w
Constraints:
range: 3-1350
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.6
The maximum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
Integer32r/w
Constraints:
range: 4-1800
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.7
Indicates the lifetime of the router as the default router.
Integer32r/w
Constraints:
range: 0-9000
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.8
Indicates the amount of time that a node can consider a neighboring
node reachable after receiving a reachability confirmation.
Integer32r/w
Constraints:
range: 0-3600000
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.9
Indicates the amount of time between retransmissions of neighbor
solicited messages.
The unit is set in millisecond.
Unsigned32r/w
Constraints:
range: 0-4294967295
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.10
Indicates the default value of the hop limit field in the IPv6 header for
packets sent by hosts that receive this RA message.
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.11
When enabled, it indicates that hosts receiving this RA must use a
stateful address configuration protocol to obtain an address in the addition
to the addresses derived from the stateless address configuration.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.12
When enabled, it indicates that hosts receiving this RA must use a stateful
address configuration protocol to obtain an on-link address configuration information.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.4.1.13
.1.3.6.1.4.1.171.11.101.3.3.2.1.5 · 1 row entry · 9 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3Ipv6AddressCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3224-SWL3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3224-SWL3MGMT-MIB::swL3Ipv6AddressCtrlTable'
This table contains IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry row .1.3.6.1.4.1.171.11.101.3.3.2.1.5.1
A list of information about a specific IPv6 address.
Column Syntax OID
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.1
Specify the IPv6 address.
Ipv6Address
Type Constraints:
range: 16
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.2
Indicates the prefix length of this IPv6 address.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.3
Indicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains in preferred state.
For an infinite valid lifetime, the value can be set to 0xfffffff…
Unsigned32r/w
Constraints:
range: 0-4294967294
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.4
Indicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains valid.
For an infinite valid lifetime, the value can be set to 0xffffffff.
Unsigned32r/w
Constraints:
range: 0-4294967294
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.5
When enabled, the address implied by the specified prefix is available
on the link where the RA message is received.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.6
When enabled, the specified prefix will be used to create an autonomous address configuration.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.7
This variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.8
This object indicates the type of the IPv6 address.
manual(1): the IPv6 address is configured by user.
dhcpv6(2): the IPv6 address is assigned by DHCPv6 server.
stateless(3): the IPv6 address is assigned by router adver…
Enumeration
Enumerated Values:
1manual
2dhcpv6
3stateless
.1.3.6.1.4.1.171.11.101.3.3.2.1.5.1.9