DGS3000-10TC-L3MGMT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Tables
21
Rows
21
Columns
173
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3 · 1 row entry · 20 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3IpCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3IpCtrlTable'
This table contains IP interface information.
swL3IpCtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1
A list of information about a specific IP interface.
Column Syntax OID
swL3IpCtrlInterfaceNameThis object indicates the name of the IP interface.OctetString
Constraints:
range: 1-12
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.1
swL3IpCtrlIfIndexThis object uniquely identifies the IP interface number in the
swL3IpCtrlTable.
Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.2
swL3IpCtrlIpAddrThe IP address of the interface. This object only can take the
value of the unicast IP address.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.3
swL3IpCtrlIpSubnetMaskThe IP net mask for this interface.SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.4
swL3IpCtrlVlanNameThis object indicates the IP control entry's VLAN name. The
VLAN name in each entry must be unique in the IP Control Table.
OctetStringr/w
Constraints:
range: 0-32
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.5
swL3IpCtrlProxyArpThis object indicates enable/disable of the proxy ARP function for IPv4.Enumerationr/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.6
swL3IpCtrlSecondaryWhen this is true(1), the IP address is the secondary IP. When
false(2), the IP address is the primary IP.
SNMPv2-TCTruthValuer/w
Constraints:
range: 0-127
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.7
swL3IpCtrlModeThis object indicates the IP operation mode.

other(1) - This entry is currently in use but the conditions under
which it will remain are determined by each of the following values.
bootp(3) - The I…
Enumerationr/w
Enumerated Values:
1none
2log
3snmp-trap
4log-and-trap
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.8
swL3IpCtrlAdminStateThe state of the IP interface.Enumerationr/w
Constraints:
range: 0-127
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.9
swL3IpCtrlIpv4AdminStateThe IPv4 admin state of the IP interface. The default state is determined by project.
This state will only be effective when the swL3IpCtrlAdminState is enabled.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.10
swL3IpCtrlIpv6AdminStateThe IPv6 admin state of the IP interface. The default state is determined by project.
This state will only be effective when the swL3IpCtrlAdminState is enabled.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.12
swL3IpCtrlIpv6LinkLocalAddressThe IPv6 link local address for this interface.Ipv6Address
Type Constraints:
range: 16
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.14
swL3IpCtrlIpv6LinkLocalPrefixLenThe IPv6 prefix length for this IPv6 link local address.SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.15
swL3IpCtrlStateThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.16
swL3IpCtrlIpv6LinkLocalAutoStateThe state of the IPv6 link local auto.Enumerationr/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.17
swL3IpCtrlLocalProxyArpThis object indicates enable/disable of the local proxy ARP function for IPv4.Enumerationr/w
Constraints:
range: 1-2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.18
swL3IpCtrlDhcpv6ClientStateThe object indicates the state of the DHCPv6 client.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.20
swL3IpCtrlIpDirectedBroadcastStateThe object indicates the state of the IP Directed Broadcast.Enumerationr/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.21
swL3IpCtrlIpDhcpOption12StateEnable or disable insertion of option 12 in the DHCPDISCOVER and
DHCPREQUEST message.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.22
swL3IpCtrlIpDhcpOption12HostNameSpecify the host name to be inserted in the DHCPDISCOVER and
DHCPREQUEST message. The specified host name must start with a
letter, end with a letter or digit, and have only letters, digits,
and hyphen as interior ch…
OctetStringr/w
Constraints:
range: 0-63
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.3.1.23
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4 · 1 row entry · 12 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3Ipv6CtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3Ipv6CtrlTable'
This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Column Syntax OID
swL3Ipv6CtrlInterfaceNameThis object indicates the name of the IP interface.OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.1
swL3Ipv6CtrlMaxReassmblySizeMaximum Reassembly Size of the IP interface.SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.2
swL3Ipv6CtrlNsRetransTimerNeighbor solicitation's retransmit timer.
The unit is set in milliseconds.
Unsigned32r/w
Constraints:
range: 0-4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.3
swL3Ipv6CtrlRaStateNeighbor solicited state.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.5
swL3Ipv6CtrlRaMinRtrAdvIntervalThe minimum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInt…
Integer32r/w
Constraints:
range: 3-1350
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.6
swL3Ipv6CtrlRaMaxRtrAdvIntervalThe maximum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
Integer32r/w
Constraints:
range: 4-1800
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.7
swL3Ipv6CtrlRaLifeTimeIndicates the lifetime of the router as the default router.Integer32r/w
Constraints:
range: 0-9000
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.8
swL3Ipv6CtrlRaReachableTimeIndicates the amount of time that a node can consider a neighboring
node reachable after receiving a reachability confirmation.
Integer32r/w
Constraints:
range: 0-3600000
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.9
swL3Ipv6CtrlRaRetransTimeIndicates the amount of time between retransmissions of neighbor
solicited messages.
The unit is set in millisecond.
Unsigned32r/w
Constraints:
range: 0-4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.10
swL3Ipv6CtrlRaHopLimitIndicates the default value of the hop limit field in the IPv6 header for
packets sent by hosts that receive this RA message.
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.11
swL3Ipv6CtrlRaManagedFlagWhen enabled, it indicates that hosts receiving this RA must use a
stateful address configuration protocol to obtain an address in the addition
to the addresses derived from the stateless address configuration.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.12
swL3Ipv6CtrlRaOtherConfigFlagWhen enabled, it indicates that hosts receiving this RA must use a stateful
address configuration protocol to obtain an on-link address configuration information.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.4.1.13
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5 · 1 row entry · 9 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3Ipv6AddressCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3Ipv6AddressCtrlTable'
This table contains IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1
A list of information about a specific IPv6 address.
Column Syntax OID
swL3Ipv6AddressCtrlInterfaceNameThis object indicates the name of the IP interface.OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.1
swL3Ipv6AddressSpecify the IPv6 address.Ipv6Address
Type Constraints:
range: 16
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.2
swL3Ipv6AddressCtrlPrefixLenIndicates the prefix length of this IPv6 address.SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.3
swL3Ipv6AddressCtrlPreferredLifeTimeIndicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains in preferred state.
For an infinite valid lifetime, the value can be set to 0xfffffff…
Unsigned32r/w
Constraints:
range: 0-4294967294
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.4
swL3Ipv6AddressCtrlValidLifeTimeIndicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains valid.
For an infinite valid lifetime, the value can be set to 0xffffffff.
Unsigned32r/w
Constraints:
range: 0-4294967294
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.5
swL3Ipv6AddressCtrlOnLinkFlagWhen enabled, the address implied by the specified prefix is available
on the link where the RA message is received.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.6
swL3Ipv6AddressCtrlAutonomousFlagWhen enabled, the specified prefix will be used to create an autonomous address configuration.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.7
swL3Ipv6AddressCtrlStateThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.8
swL3Ipv6AddressCtrlAddressTypeThis object indicates the type of the IPv6 address.
manual(1): the IPv6 address is configured by user.
dhcpv6(2): the IPv6 address is assigned by DHCPv6 server.
stateless(3): the IPv6 address is assigned by router adver…
Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.2.1.5.1.9
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8 · 1 row entry · 6 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3LoopBackIpCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3LoopBackIpCtrlTable'
This table contains loopback IP interface information.
swL3LoopBackIpCtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1
A list of information about a specific loopback IP interface.
Column Syntax OID
swL3LoopBackIpCtrlInterfaceNameThis object indicates the name of the loopback IP interface.OctetString
Constraints:
range: 1-12
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.1
swL3LoopBackIpCtrlIfIndexThis object uniquely identifies the loopback IP interface number in the
swL3LoopBackIpCtrlTable.
Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.2
swL3LoopBackIpCtrlIpAddrThe IP address of the loopback interface. This object only can take the
value of the unicast IP address.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.3
swL3LoopBackIpCtrlIpSubnetMaskThe IP net mask for this loopback interface.SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.4
swL3LoopBackIpCtrlAdminStateThe state of the loopback IP interface.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.5
swL3LoopBackIpCtrlRowStatusThis variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.2.1.8.1.6
.1.3.6.1.4.1.171.11.133.1.1.3.2.2.1 · 1 row entry · 4 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3IpFdbInfoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3IpFdbInfoTable'
A table that contains forwarding and/or filtering information.
This information is used by the switch in determining how to
propagate the received IP packets.
swL3IpFdbInfoEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.2.1.1
Information about a specific IP address for which the bridge
has some forwarding and/or filtering information.
Column Syntax OID
swL3IpFdbInfoIpAddrA IP address for which switch has forwarding and/or filtering
information.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.2.1.1.1
swL3IpFdbInfoIpSubnetMaskA IP net mask for this interface for which the switch has
forwarding and/or filtering information.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.2.1.1.2
swL3IpFdbInfoPortEither the value '0', or the port number of the port on which
packet having a IP address equal to the value of the
corresponding instance of swL3IpFdbInfoIpAddr has been seen. A
value of '0' indicates that the port nu…
Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.2.1.1.3
swL3IpFdbInfoTypeThe status of this entry.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.2.2.1.1.4
.1.3.6.1.4.1.171.11.133.1.1.3.2.5 · 1 row entry · 9 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3IpStaticRouteTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3IpStaticRouteTable'
This entity's IP static Routing table.
swL3IpStaticRouteEntry row .1.3.6.1.4.1.171.11.133.1.1.3.2.5.1
A particular route to a particular destination, under a particular policy.
Once an entry is built,it shouldn't be modified.That is,it just supports
create and delete actions.
Column Syntax OID
swL3IpStaticRouteDestThe destination IP address of this route.

This object may not take a Multicast (Class D)
address value.

Any assignment (implicit or otherwise) of an
instance of this object to a valu…
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.1
swL3IpStaticRouteMaskIndicate the mask to be logical-AND with the
destination address before being compared to
the value in the swL3IpStaticRouteDest field.
For those systems that do not support arbitrary
subnet masks, an agent c…
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.2
swL3IpStaticRouteBkupStateThe routing state for this route.The value SHOULD be
primary(1), backup(2) or none(3).
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.3
swL3IpStaticRouteNextHopSpecifies the IP address for the next hop router.
An IP address of 255.255.255.255 denotes a Null interface
as the next hop.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.4
swL3IpStaticRouteMetricSpecifies the routing metric for this route.Integer32r/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.5
swL3IpStaticRouteStatusThis object indicates the status of this entry.

other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.6
swL3IpStaticRouteWeightSpecifies the weight value. Used for the weighted multipath.Integer32r/w
Constraints:
range: 0-4
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.7
swL3IpStaticRouteInterfaceNameSpecifies the name of the IP interface.SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.8
swL3IpStaticRouteCostSpecifies the cost of the Route Entry.SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.2.5.1.9
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.4 · 1 row entry · 3 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3RelayDhcpCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3RelayDhcpCtrlTable'
This table specifies the IP address as a destination to forward
(relay) DHCP packets to.
swL3RelayDhcpCtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.3.1.4.1
A list of information specifying the IP address as a destination
to forward (relay) DHCP packets to.
Column Syntax OID
swL3RelayDhcpCtrlInterfaceNameThe name of the IP interface.OctetString
Constraints:
range: 0-12
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.4.1.1
swL3RelayDhcpCtrlServerThe DHCP server IP address.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.4.1.2
swL3RelayDhcpCtrlStateThis object indicates the status of this entry.

other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.3.1.4.1.3
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.3 · 1 row entry · 2 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3DHCPRelayOption60DefTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3DHCPRelayOption60DefTable'
This table indicates the default relay servers for the packet
that has no option 60 mathcing rules.
swL3DHCPRelayOption60DefEntry row .1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.3.1
A list of information indicates the default relay servers for the packet
that has no option 60 mathcing rules.
Column Syntax OID
swL3DHCPRelayOption60DefRelayIpThis object indicates the IP address of default relay server.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.3.1.1
swL3DHCPRelayOption60DefRowStatusThis object indicates the status of this entry.SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.3.1.2
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4 · 1 row entry · 4 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3DHCPRelayOption60Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3DHCPRelayOption60Table'
This table indicates the relay servers for the packet at option 60 rules.
swL3DHCPRelayOption60Entry row .1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4.1
A list of information indicates the relay servers for the packet
at option 60 rules.
Column Syntax OID
swL3DHCPRelayOption60StringThis object indicates string of this entry.SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4.1.1
swL3DHCPRelayOption60RelayIpThis object indicates the IP address of relay server.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4.1.2
swL3DHCPRelayOption60MatchTypeThis object indicates match state of this entry.

exact(1): means the option 60 string in the packet must full
match with the specified string.
partial(2): means the option 60 string in the packet only ne…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4.1.3
swL3DHCPRelayOption60RowStatusThis object indicates the status of this entry.SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.8.4.1.4
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4 · 1 row entry · 5 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3DHCPRelayOption61Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3DHCPRelayOption61Table'
This table indicates the relay servers for the packet at option 61 rules.
swL3DHCPRelayOption61Entry row .1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1
A list of information indicates the relay servers for the packet
at option 61 rules.
Column Syntax OID
swL3DHCPRelayOption61ClientTypeThis object indicates client type of this entry.

mac(1): means the client-ID which is the MAC address of client.
string(2): means the client-ID which is specified string by administrator.
Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1.1
swL3DHCPRelayOption61ClientIDThis object indicates string of this entry.

When swL3DHCPRelayOption61ClientType is mac(1), the format of this
object should be XX-XX-XX-XX-XX-XX (MAC address).
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1.2
swL3DHCPRelayOption61ModeThis object indicates mode of this entry.

relay(1): means to relay the packet to the IP address which is specified
by swL3DHCPRelayOption61RelayIp.
drop(2): means to drop the packet.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1.3
swL3DHCPRelayOption61RelayIpThis object indicates the IP address of relay server.

Pay attention to when swL3DHCPRelayOption61Mode is:
relay(1): this object must be set together.
drop(2): this object can not be set, and it always ret…
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1.4
swL3DHCPRelayOption61RowStatusThis object indicates the status of this entry.SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.3.1.9.4.1.5
.1.3.6.1.4.1.171.11.133.1.1.3.3.2.6 · 1 row entry · 3 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3RelayDnsCtrlTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3RelayDnsCtrlTable'
This table displays the current DNS relay static table.
swL3RelayDnsCtrlEntry row .1.3.6.1.4.1.171.11.133.1.1.3.3.2.6.1
A list of information display the current DNS relay static
table.
Column Syntax OID
swL3RelayDnsCtrlDomainNameThe domain name of the entry.OctetString
Constraints:
range: 1-32
.1.3.6.1.4.1.171.11.133.1.1.3.3.2.6.1.1
swL3RelayDnsCtrlIpAddrThe IP address of the entry.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.3.2.6.1.2
swL3RelayDnsCtrlStateThis object indicates the status of this entry.

other(1) - this entry is currently in use but the conditions
under which it will remain so are different from each of
the following values.
invalid(…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.3.2.6.1.3

swL3Md5Table

table
.1.3.6.1.4.1.171.11.133.1.1.3.4 · 1 row entry · 3 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3Md5Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3Md5Table'
This table displays the current MD5 key table.
swL3Md5Entry row .1.3.6.1.4.1.171.11.133.1.1.3.4.1
A list of information displays the current MD5 key table.
Indexes
Column Syntax OID
swL3Md5KeyIdThe MD5 key ID.Integer32
Constraints:
range: 1-255
.1.3.6.1.4.1.171.11.133.1.1.3.4.1.1
swL3Md5KeyAn MD5 password of up to 16 bytes.OctetStringr/w
Constraints:
range: 1-16
.1.3.6.1.4.1.171.11.133.1.1.3.4.1.2
swL3Md5RowStatusThis object indicates the status of this entry.SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.4.1.3
.1.3.6.1.4.1.171.11.133.1.1.3.5 · 1 row entry · 6 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3RouteRedistriTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3RouteRedistriTable'
Route redistribution allows routers on the network that are 
running different routing protocols to exchange routing 
information. This is accomplished by comparing the routes stored
in the varios routers' routing tables and assigning appropriate
metrics. This information is then exchanged among the various 
routers according to the individual routers current routing 
protocol.
swL3RouteRedistriEntry row .1.3.6.1.4.1.171.11.133.1.1.3.5.1
A list of information displaying the route redistribution table.
Column Syntax OID
swL3RouteRedistriSrcProtocolAllows the selection of the protocol of the source device.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.5.1.1
swL3RouteRedistriDstProtocolAllows the selection of the protocol of the destination device.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.5.1.2
swL3RouteRedistriTypeAllows the selection of one of the methods for calculating
the metric value.
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.5.1.3
swL3RouteRedistriMetricAllows the entry of an OSPF interface cost. This is analogous
to a Hop Count in the RIP routing protocol. The value '0'
indicates default value.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.5.1.4
swL3RouteRedistriRowStatusThis object indicates the status of this entry.SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.5.1.5
swL3RouteRedistriRouteMapNameThis Object just works when the destination protocol is BGP
and indicate the route-map working when redistribute the route
to BGP.
OctetStringr/w
Constraints:
range: 0-16
.1.3.6.1.4.1.171.11.133.1.1.3.5.1.6
.1.3.6.1.4.1.171.11.133.1.1.3.6 · 1 row entry · 5 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3OspfHostTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3OspfHostTable'
The list of Hosts, and their metrics, that the router will 
advertise as host routes.
swL3OspfHostEntry row .1.3.6.1.4.1.171.11.133.1.1.3.6.1
A metric to be advertised, for a given type of service, when a
given host is reachable.
Column Syntax OID
swL3OspfHostIpAddressThe IP Address of the Host.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.6.1.1
swL3OspfHostTOSThe Type of Service of the route being configured.OSPF-MIBTOSType
Type Constraints:
range: 0..30
.1.3.6.1.4.1.171.11.133.1.1.3.6.1.2
swL3OspfHostMetricThe Metric to be advertised.OSPF-MIBMetricr/w
Type Constraints:
range: 0..65535
.1.3.6.1.4.1.171.11.133.1.1.3.6.1.3
swL3OspfHostAreaIDThe Area the Host Entry is to be found within. By default, the
area that a subsuming OSPF interface is in, or 0.0.0.0
OSPF-MIBAreaIDr/w.1.3.6.1.4.1.171.11.133.1.1.3.6.1.4
swL3OspfHostStatusThis variable displays the status of the entry. Setting it to
'invalid' has the effect of rendering it inoperative. The internal
effect (row removal) is implementation dependent.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.6.1.5
.1.3.6.1.4.1.171.11.133.1.1.3.7 · 1 row entry · 12 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3ospfVirtIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3ospfVirtIfTable'
Information about this router's virtual inter-
faces.
swL3ospfVirtIfEntry row .1.3.6.1.4.1.171.11.133.1.1.3.7.1
Information about a single Virtual Interface.
Column Syntax OID
swL3ospfVirtIfAreaIdThe Transit Area that the Virtual Link
traverses. By definition, this is not 0.0.0.0
OSPF-MIBAreaID.1.3.6.1.4.1.171.11.133.1.1.3.7.1.1
swL3ospfVirtIfNeighborThe Router ID of the Virtual Neighbor.OSPF-MIBRouterID.1.3.6.1.4.1.171.11.133.1.1.3.7.1.2
swL3ospfVirtIfTransitDelayThe estimated number of seconds it takes to
transmit a link- state update packet over this
interface.
OSPF-MIBUpToMaxAger/w
Type Constraints:
range: 0..3600
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.3
swL3ospfVirtIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state reque…
OSPF-MIBUpToMaxAger/w
Type Constraints:
range: 0..3600
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.4
swL3ospfVirtIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for the
virtual neighbor.
OSPF-MIBHelloRanger/w
Type Constraints:
range: 1..65535
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.5
swL3ospfVirtIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for t…
Integer32r/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.6
swL3ospfVirtIfStateOSPF virtual interface states.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.7.1.7
swL3ospfVirtIfEventsThe number of state changes or error events on
this Virtual Link
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.8
swL3ospfVirtIfAuthTypeThe authentication type specified for a virtu-
al interface. Additional authentication types
may be assigned locally.
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.9
swL3ospfVirtIfAuthKeyIf Authentication Type is simplePassword, the
device will left adjust and zero fill to 8 oc-
tets.

Note that unauthenticated interfaces need no
authentication key, and simple password authen-
ticatio…
OctetStringr/w
Constraints:
range: 0-256
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.10
swL3ospfVirtIfAuthKeyIDThe MD5 key ID.Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.11
swL3ospfVirtIfStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.7.1.12
.1.3.6.1.4.1.171.11.133.1.1.3.8 · 1 row entry · 22 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3ospfIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3ospfIfTable'
The OSPF Interface Table describes the  inter-
faces from the viewpoint of OSPF.
swL3ospfIfEntry row .1.3.6.1.4.1.171.11.133.1.1.3.8.1
The OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF.
Column Syntax OID
swL3ospfIfIpAddressThe IP address of this OSPF interface.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.1
swL3ospfAddressLessIfFor the purpose of easing the instancing of
addressed and addressless interfaces; This
variable takes the value 0 on interfaces with
IP Addresses, and the corresponding value of
ifIndex for interfaces havin…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.2
swL3ospfIfAreaIdA 32-bit integer uniquely identifying the area
to which the interface connects. Area ID
0.0.0.0 is used for the OSPF backbone.
OSPF-MIBAreaIDr/w.1.3.6.1.4.1.171.11.133.1.1.3.8.1.3
swL3ospfIfTypeThe OSPF interface type.

By way of a default, this field may be intuited
from the corresponding value of ifType. Broad-
cast LANs, such as Ethernet and IEEE 802.5,
take the value 'broadcast', X.25…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.8.1.4
swL3ospfIfAdminStatThe OSPF interface's administrative status.
The value formed on the interface, and the in-
terface will be advertised as an internal route
to some area. The value 'disabled' denotes
that the interface is extern…
OSPF-MIBStatusr/w
Type Values:
1enabled
2disabled
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.5
swL3ospfIfRtrPriorityThe priority of this interface. Used in
multi-access networks, this field is used in
the designated router election algorithm. The
value 0 signifies that the router is not eligi-
ble to become the designate…
OSPF-MIBDesignatedRouterPriorityr/w
Type Constraints:
range: 0..255
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.6
swL3ospfIfTransitDelayThe estimated number of seconds it takes to
transmit a link state update packet over this
interface.
OSPF-MIBUpToMaxAger/w
Type Constraints:
range: 0..3600
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.7
swL3ospfIfRetransIntervalThe number of seconds between link-state ad-
vertisement retransmissions, for adjacencies
belonging to this interface. This value is
also used when retransmitting database descrip-
tion and link-state request …
OSPF-MIBUpToMaxAger/w
Type Constraints:
range: 0..3600
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.8
swL3ospfIfHelloIntervalThe length of time, in seconds, between the
Hello packets that the router sends on the in-
terface. This value must be the same for all
routers attached to a common network.
OSPF-MIBHelloRanger/w
Type Constraints:
range: 1..65535
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.9
swL3ospfIfRtrDeadIntervalThe number of seconds that a router's Hello
packets have not been seen before it's neigh-
bors declare the router down. This should be
some multiple of the Hello interval. This
value must be the same for a…
OSPF-MIBPositiveIntegerr/w
Type Constraints:
range: 0..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.10
swL3ospfIfPollIntervalThe larger time interval, in seconds, between
the Hello packets sent to an inactive non-
broadcast multi- access neighbor.
OSPF-MIBPositiveIntegerr/w
Type Constraints:
range: 0..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.11
swL3ospfIfStateThe OSPF Interface State.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.8.1.12
swL3ospfIfDesignatedRouterThe IP Address of the Designated Router.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.13
swL3ospfIfBackupDesignatedRouterThe IP Address of the Backup Designated
Router.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.14
swL3ospfIfEventsThe number of times this OSPF interface has
changed its state, or an error has occurred.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.15
swL3ospfIfMulticastForwardingThe way multicasts should forwarded on this
interface; not forwarded, forwarded as data
link multicasts, or forwarded as data link uni-
casts. Data link multicasting is not meaning-
ful on point to point and NB…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.8.1.16
swL3ospfIfDemandIndicates whether Demand OSPF procedures (hel-
lo supression to FULL neighbors and setting the
DoNotAge flag on proogated LSAs) should be per-
formed on this interface.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.17
swL3ospfIfAuthTypeThe authentication type specified for an in-
terface. Additional authentication types may
be assigned locally.
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.18
swL3ospfIfAuthKeyThe Authentication Key. If the Area's Author-
ization Type is simplePassword, and the key
length is shorter than 8 octets, the agent will
left adjust and zero fill to 8 octets.

Note that unauthentica…
OctetStringr/w
Constraints:
range: 0-256
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.19
swL3ospfIfAuthKeyIDThe MD5 key ID.Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.20
swL3ospfIfPassiveModeAssign the designated entry to be a passive interface.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.8.1.21
swL3ospfIfMetricThe Metric to be advertised.OSPF-MIBMetricr/w
Type Constraints:
range: 0..65535
.1.3.6.1.4.1.171.11.133.1.1.3.8.1.23
.1.3.6.1.4.1.171.11.133.1.1.3.10 · 1 row entry · 6 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3ospfAreaTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3ospfAreaTable'
Information describing the configured  parame-
ters  and cumulative statistics of the router's
attached areas.
swL3ospfAreaEntry row .1.3.6.1.4.1.171.11.133.1.1.3.10.1
Information describing the configured parame-
ters and cumulative statistics of one of the
router's attached areas.
Indexes
Column Syntax OID
swL3ospfAreaIdA 32-bit integer uniquely identifying an area.
Area ID 0.0.0.0 is used for the OSPF backbone.
OSPF-MIBAreaID.1.3.6.1.4.1.171.11.133.1.1.3.10.1.1
The type specified for an area.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.10.1.2
swL3ospfAreaSummaryStateWhether the summary LSA is effective for this area.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.10.1.3
swL3ospfAreaMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.Integer32r/w
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.10.1.4
swL3ospfAreaTranslateState.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.10.1.5
swL3ospfAreaStatusThis variable displays the status of the en-
try. Setting it to 'invalid' has the effect of
rendering it inoperative. The internal effect
(row removal) is implementation dependent.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.10.1.6
.1.3.6.1.4.1.171.11.133.1.1.3.12 · 1 row entry · 8 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3dvmrpInterfaceTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3dvmrpInterfaceTable'
The (conceptual) table listing the router's multicast-
capable interfaces.
swL3dvmrpInterfaceEntry row .1.3.6.1.4.1.171.11.133.1.1.3.12.1
An entry (conceptual row) in the dvmrpInterfaceTable. This
row augments ipMRouteInterfaceEntry in the IP Multicast MIB,
where the threshold object resides.
Column Syntax OID
swL3dvmrpInterfaceIfIndexThe ifIndex value of the interface for which DVMRP is
enabled.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.1
swL3dvmrpInterfaceLocalAddressThe IP address this system will use as a source address on
this interface. On unnumbered interfaces, it must be the
same value as dvmrpInterfaceLocalAddress for some interface
on the system.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.2
swL3dvmrpInterfaceMetricThe distance metric for this interface which is used to
calculate distance vectors.
Integer32r/w
Constraints:
range: 1-31
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.3
swL3dvmrpInterfaceProbeProbe distribution interval.Integer32r/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.4
swL3dvmrpInterfaceNbrTimeoutUsed to set the timer before neighbors are timed out.Integer32r/w
Constraints:
range: 1-65535
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.5
swL3dvmrpInterfaceStatusThe status of this entry. Creating the entry enables DVMRP
on the virtual interface; destroying the entry or setting it
to notInService disables DVMRP on the virtual interface.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.6
swL3dvmrpInterfaceRcvBadPktsThe number of DVMRP packets received on the interface by
the DVMRP process which were subsequently discarded as
invalid (e.g. invalid packet format, or a route report from
an unknown neighbor).
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.7
swL3dvmrpInterfaceRcvBadRoutesThe number of routes, in valid DVMRP packets, which were
ignored because the entry was invalid.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.12.1.8
.1.3.6.1.4.1.171.11.133.1.1.3.13.1 · 1 row entry · 8 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3OspfInternalLsdbTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3OspfInternalLsdbTable'
The OSPF Process's Link State Database.
swL3OspfInternalLsdbEntry row .1.3.6.1.4.1.171.11.133.1.1.3.13.1.1
A single Link State Advertisement.
Column Syntax OID
swL3OspfInternalLsdbAreaIdThe 32 bit identifier of the Area from which
the LSA was received.
OSPF-MIBAreaID.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.1
swL3OspfInternalLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format.
Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.2
swL3OspfInternalLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.3
swL3OspfInternalLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.
OSPF-MIBRouterID.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.4
swL3OspfInternalLsdbMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.5
swL3OspfInternalLsdbSequenceNoThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number t…
OctetString
Constraints:
range: 4-4
.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.6
swL3OspfInternalLsdbAgeThis field is the age of the link state adver-
tisement in seconds.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.7
swL3OspfInternalLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, excepting the
age field. The age field is excepted so that
an advertisement's age can be incremented
without updating the checks…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.13.1.1.8
.1.3.6.1.4.1.171.11.133.1.1.3.13.2 · 1 row entry · 10 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3OspfExternalLsdbTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3OspfExternalLsdbTable'
The OSPF Process's Links State Database.
swL3OspfExternalLsdbEntry row .1.3.6.1.4.1.171.11.133.1.1.3.13.2.1
A single Link State Advertisement.
Column Syntax OID
swL3OspfExternalLsdbTypeThe type of the link state advertisement.
Each link state type has a separate advertise-
ment format.
Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.1
swL3OspfExternalLsdbLsidThe Link State ID is an LS Type Specific field
containing either a Router ID or an IP Address;
it identifies the piece of the routing domain
that is being described by the advertisement.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.2
swL3OspfExternalLsdbRouterIdThe 32 bit number that uniquely identifies the
originating router in the Autonomous System.
OSPF-MIBRouterID.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.3
swL3OspfExternalLsdbMetricEnter the metric (1 - 65535; 0 for auto cost) of this area.Integer32
Constraints:
range: 0-65535
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.4
swL3OspfExternalLsdbMetricTypeEnter the metric type of this area.Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.5
swL3OspfExternalLsdbSequenceNoThe sequence number field is a signed 32-bit
integer. It is used to detect old and dupli-
cate link state advertisements. The space of
sequence numbers is linearly ordered. The
larger the sequence number t…
OctetString
Constraints:
range: 4-4
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.6
swL3OspfExternalLsdbAgeThis field is the age of the link state adver-
tisement in seconds.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.7
swL3OspfExternalLsdbChecksumThis field is the checksum of the complete
contents of the advertisement, except the
age field. The age field is the exception so that
an advertisement's age can be incremented
without updating the checksum. Th…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.8
swL3OspfExternalLsdbForwardingAddressThis field is the forwarding address.SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.9
swL3OspfExternalLsdbRouteTagThis field is the route tag.OctetString.1.3.6.1.4.1.171.11.133.1.1.3.13.2.1.10
.1.3.6.1.4.1.171.11.133.1.1.3.14.1 · 1 row entry · 16 columns
Uses the d-link variant from /opt/observium/mibs/d-link.
Command help
Walk swL3VrrpOperTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DGS3000-10TC-L3MGMT-MIB' -M '/opt/observium/mibs/d-link:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DGS3000-10TC-L3MGMT-MIB::swL3VrrpOperTable'
Operations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
'swL3vrrpOperEntry' items.
swL3VrrpOperEntry row .1.3.6.1.4.1.171.11.133.1.1.3.14.1.1
An entry in the vrrpOperTable containing the operational
characteristics of a virtual router. On a VRRP router,
a given virtual router is identified by a combination
of the IF index and VRID.

Rows in the ta…
Column Syntax OID
swL3VrrpOperIfIndexThe ifIndex value of the interface for which VRRP is
enabled.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.1
swL3VrrpOperVrIdThis object contains the Virtual Router Identifier (VRID).VrId
Type Constraints:
range: 1..255
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.2
swL3VrrpOperVirtualMacAddrThe virtual MAC address of the virtual router. Although this
object can be derived from the 'swL3VrrpOperVrId' object, it is
defined so that it is easily obtainable by a management
application and can be included in VRR…
SNMPv2-TCMacAddress
Type Constraints:
range: 6
Description:
Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.3
swL3VrrpOperStateThe current state of the virtual router. This object has
three defined values:

- `initialize', which indicates that all the
virtual router is waiting for a startup event.

- `backup'…
Enumeration.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.4
swL3VrrpOperAdminStateThis object will enable/disable the virtual router
function. Setting the value to `up', will transition
the state of the virtual router from `initialize' to `backup'
or `master', depending on the value of `swL3VrrpOperP…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.5
swL3VrrpOperPriorityThis object specifies the priority to be used for the
virtual router master election process. Higher values imply
higher priority.

A priority of '0', although not settable, is sent by
the master router to…
Integer32r/w
Constraints:
range: 0-255
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.6
swL3VrrpOperMasterIpAddrThe master router's real (primary) IP address. This is
the IP address listed as the source in VRRP advertisement
last received by this virtual router.
SNMPv2-SMIIpAddress
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.7
swL3VrrpOperCriticalIpAddrIn the case where there is more than one IP address for
a given `ifIndex', this object is used to specify the IP
address that will become the `swL3VrrpOperMasterIpAddr', should
the virtual router transition from backup …
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.8
swL3VrrpOperCheckCriticalIpStateCritical IP state.Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.9
swL3VrrpOperAuthTypeAuthentication type used for VRRP protocol exchanges between
virtual routers. This value of this object is the same for a
given ifIndex.

New enumerations to this list can only be added via a new
RFC on th…
Enumerationr/w.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.10
swL3VrrpOperAuthKeyThe Authentication Key. This object is set according to
the value of the 'swL3VrrpOperAuthType' object
('simpleTextPassword' or 'ipAuthenticationHeader'). If the
length of the value is less than 16 octets, the agent wil…
OctetStringr/w
Constraints:
range: 0-16
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.11
swL3VrrpOperAdvertisementIntervalThe time interval, in seconds, between sending
advertisement messages. Only the master router sends
VRRP advertisements.
secondsInteger32r/w
Constraints:
range: 1-255
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.12
swL3VrrpOperPreemptModeControls whether a higher priority virtual router will
preempt a lower priority master.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.13
swL3VrrpOperVirtualRouterUpTimeThis is the value of the `sysUpTime' object when this
virtual router (i.e., the `swL3VrrpOperState') transitioned
out of `initialized'.
SNMPv2-TCTimeStamp
Based On: SNMPv2-SMITimeTicks
Description:
The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.14
swL3VrrpOperVirtualIpAddrThe assigned IP addresses that a virtual router is
responsible for backing up.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.15
swL3VrrpOperRowStatusThe row status variable, used in accordance to installation
and removal conventions for conceptual rows. The rowstatus of
a currently active row in the vrrpOperTable is constrained
by the operational state of the corres…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
.1.3.6.1.4.1.171.11.133.1.1.3.14.1.1.16