DGS-1210-48-AX Table View

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

sysPortCtrlEntry row .1.3.6.1.4.1.171.10.76.11.1.13.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

sysPortCtrlIndex

Column	Syntax	OID
sysPortCtrlIndex Interface index of the port for the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.76.11.1.13.1.1
sysPortCtrlSpeed Configures interface speed.	Enumerationr/w Enumerated Values: 1 rate1000M-Full 2 rate100M-Full 3 rate100M-Half 4 rate10M-Full 5 rate10M-Half 6 auto 7 disable	.1.3.6.1.4.1.171.10.76.11.1.13.1.2
sysPortCtrlOperStatus The port's operating speed state.	Enumeration Enumerated Values: 1 down 2 rate1000M-Full 3 rate100M-Full 4 rate100M-Half 5 rate10M-Full 6 rate10M-Half	.1.3.6.1.4.1.171.10.76.11.1.13.1.3
sysPortCtrlMDI Configures interface auto/mdi/mdix mode. The default setting is Auto.	Enumerationr/w Enumerated Values: 1 auto 2 mdi 3 mdix	.1.3.6.1.4.1.171.10.76.11.1.13.1.4
sysPortCtrlFlowControl Enables / disables flow control for the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.171.10.76.11.1.13.1.5
sysPortCtrlFlowControlOper The link parner negotiate port's operating flow control state.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.1.13.1.6
sysPortCtrlType The port's media type.	Enumeration Enumerated Values: 1 fastethernet 2 gigabitethernet 3 fiberwith100BaseSFPModule 4 fiberwith1000BaseSFPModule	.1.3.6.1.4.1.171.10.76.11.1.13.1.7

A table that contains port-specific information
for the Spanning Tree Protocol.

stpPortEntry row .1.3.6.1.4.1.171.10.76.11.6.2.1

A list of information maintained by every port
about the Spanning Tree Protocol state for that
port.

Indexes

stpPort

Column	Syntax	OID
stpPort The port number of the port for which this entry contains Spanning Tree Protocol management information.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.76.11.6.2.1.1
stpPortPriority The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of stpPort.	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.171.10.76.11.6.2.1.2
stpPortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will …	Enumeration Enumerated Values: 1 disabled 2 blocking 3 listening 4 learning 5 forwarding 6 broken	.1.3.6.1.4.1.171.10.76.11.6.2.1.3
stpPortEnable The enabled/disabled status of the port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.6.2.1.4
stpAdminPortPathCost The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object …	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.171.10.76.11.6.2.1.5
stpPortPathCost The contribution of this port to the path cost of paths towards the spanning tree root which include this port.	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.171.10.76.11.6.2.1.6
stpPortDesignatedRoot The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.	BridgeId Type Constraints: range: 8 Description: The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to ref…	.1.3.6.1.4.1.171.10.76.11.6.2.1.7
stpPortDesignatedCost The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.6.2.1.8
stpPortDesignatedBridge The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.	BridgeId Type Constraints: range: 8 Description: The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to ref…	.1.3.6.1.4.1.171.10.76.11.6.2.1.9
stpPortDesignatedPort The Port Identifier of the port on the Designated Bridge for this port's segment.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.171.10.76.11.6.2.1.10
stpPortForwardTransitions The number of times this port has transitioned from the Learning state to the Forwarding state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.76.11.6.2.1.11
stpPortProtocolMigration When operating in RSTP (version 2) mode, writing TRUE(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns FALSE(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.76.11.6.2.1.12
stpPortOperEdgePort The operational value of the Edge Port parameter. The object is initialized to the value of stpPortAdminEdgePort and is set FALSE on reception of a BPDU.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.76.11.6.2.1.13
stpPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.171.10.76.11.6.2.1.14
stpPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-det…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.76.11.6.2.1.15
stpPortEdge This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.	Enumerationr/w Enumerated Values: 0 false 1 true 2 auto	.1.3.6.1.4.1.171.10.76.11.6.2.1.16
stpPortRestrictedRole A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Po…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.76.11.6.2.1.17
stpPortRestrictedTCN A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.76.11.6.2.1.18

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

dot1qVlanEntry row .1.3.6.1.4.1.171.10.76.11.7.6.1

Information for a VLAN configured into the
device by (local or network) management.

Indexes

dot1qVlanName

Column	Syntax	OID
dot1qVlanName An administratively assigned string, which may be used to identify the VLAN.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.171.10.76.11.7.6.1.1
dot1qVlanEgressPorts The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVR…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.7.6.1.2
dot1qVlanForbiddenPorts The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar contro…	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.7.6.1.3
dot1qVlanUntaggedPorts The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There …	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.7.6.1.4
dot1qVlanRowStatus The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.7.6.1.5

A table containing per port control and status
information for VLAN configuration in the device.

dot1qVlanPortEntry row .1.3.6.1.4.1.171.10.76.11.7.7.1

Information controlling VLAN configuration for a port
on the device.

Indexes

No indexes recorded

Column	Syntax	OID
dot1qVlanPvid The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.	VlanIndexr/w Description: A value used to index per-VLAN tables: values of 0 and 4095 are not permitted; if the value is between 1 and 4094 inclusive, it represents an IEEE 802.1Q VLAN-ID with global scope within a given bridged domain (see Vlan…	.1.3.6.1.4.1.171.10.76.11.7.7.1.1

This table contains the list of ports through which 
a router, in a particular VLAN is reachable.

dot1qVlanUngisterMCFilterEntry row .1.3.6.1.4.1.171.10.76.11.7.8.1

A list of multicast filter mode information for each VLAN ID.

Indexes

dot1qVlanUngisterMCFilterVlanId

Column	Syntax	OID
dot1qVlanUngisterMCFilterVlanId Per Vlan to configure multicast filtering function.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.76.11.7.8.1.1
dot1qVlanUngisterMCFiltermode Filter unknown multicast frames or normal operation(i.e. forwarding)	Enumerationr/w Enumerated Values: 0 forward 1 filter	.1.3.6.1.4.1.171.10.76.11.7.8.1.2

A Port-channel is created through ifMain table.
After the creation of the port-channel, corresponding logical
interface will be created in the ifMain table. 
This Port-channel table is indexed through Key values and allows to 
configure link selection policy and the Mac address for 
the port-channel. All other objects in this table displays 
the details of the port-channel.

laPortChannelEntry row .1.3.6.1.4.1.171.10.76.11.8.1.3.1

There is one entry in this table for each created
port-channel port.

Indexes

laPortChannelIfIndex

Column	Syntax	OID
laPortChannelIfIndex The index of the port-channel(Aggregator's interface index).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.76.11.8.1.3.1.1
laPortChannelMemberList Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.8.1.3.1.2
laPortChannelMode Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.	PortLaModer/w Type Values: 1 lacp 2 static 3 disable Description: Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. s…	.1.3.6.1.4.1.171.10.76.11.8.1.3.1.3

A table that contains Link Aggregation Control
configuration information about every
Aggregation Port associated with this device.
A row appears in this table for each physical port.

laPortControlEntry row .1.3.6.1.4.1.171.10.76.11.8.2.1.1

A list of Link Aggregation Control configuration
parameters for each Aggregation Port on this device.

Indexes

laPortControlIndex

Column	Syntax	OID
laPortControlIndex The index of the port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.76.11.8.2.1.1.1
laPortActorPortPriority The priority value assigned to this Aggregation Port. This 16-bit value is read-write.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.10.76.11.8.2.1.1.2
laPortActorActivity This object indicates LACP_Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and part…	Enumerationr/w Enumerated Values: 1 active 2 passive	.1.3.6.1.4.1.171.10.76.11.8.2.1.1.3
laPortActorTimeout This object indicates LACP_Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.	Enumerationr/w Enumerated Values: 1 short 2 long	.1.3.6.1.4.1.171.10.76.11.8.2.1.1.4

A list of the Static MACs

staticEntry row .1.3.6.1.4.1.171.10.76.11.9.3.1

A Static MAC entry containing the mac and forwarding port.

Indexes

staticVlanID staticMac staticPort

Column	Syntax	OID
staticVlanID The VLAN ID of the static MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.9.3.1.1
staticMac The MAC address associated of the static MAC entry.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.9.3.1.2
staticPort The forwarding port of the static MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.9.3.1.3
staticStatus The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.9.3.1.4

This table contains the list of ports through which 
a router, in a particular VLAN is reachable.

igsVlanRouterEntry row .1.3.6.1.4.1.171.10.76.11.10.3.3.1

An igs vlan router entry contain the igs vlan router port list.

Indexes

igsVlanRouterVlanId

Column	Syntax	OID
igsVlanRouterVlanId It is the VLAN ID of the igs vlan router entry.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.76.11.10.3.3.1.1
igsVlanRouterPortList List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.10.3.3.1.2

This table contains configuration of snooping
on specific Vlans. This Table is valid only when VLAN is  
enabled in the system.

igsVlanFilterEntry row .1.3.6.1.4.1.171.10.76.11.10.3.4.1

Contains snooping status , version and fast leave
configuration for a specific VLAN.

Indexes

igsVlanFilterVlanId

Column	Syntax	OID
igsVlanFilterVlanId Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.1
igsVlanSnoopStatus This object allows you to enable/disable IGS function on a specific VLAN.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.2
igsVlanQuerier Indicates whether the switch is configured as a querier in the VLAN	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.3
igsVlanCfgQuerier The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.4
igsVlanQueryInterval This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in th…	Integer32 Constraints: range: 60-600	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.5
igsVlanRtrPortList List of ports which are configured statically as router ports	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.10.3.4.1.6

This table contains MAC based multicast forwarding 
information.

igsVlanMulticastGroupEntry row .1.3.6.1.4.1.171.10.76.11.10.3.5.1

This table contains VLAN ID, multicast group MAC address and the
list of ports onto which the multicast data packets for group
should be forwarded.

Indexes

igsVlanMulticastGroupVlanId igsVlanMulticastGroupIpAddress

Column	Syntax	OID
igsVlanMulticastGroupVlanId VLAN ID pertaining to the Multicast forwarding entry	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.76.11.10.3.5.1.1
igsVlanMulticastGroupIpAddress Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.76.11.10.3.5.1.2
igsVlanMulticastGroupMacAddress Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.10.3.5.1.3
igsVlanMulticastGroupPortList List of ports onto which the multicast data packets destined for this group will be forwarded.	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.10.3.5.1.4

A table that contains the configuration objects for the 
Authenticator PAE associated with each port. 
An entry appears in this table for each port that may 
authenticate access to itself.

dot1xAuthConfigPortEntry row .1.3.6.1.4.1.171.10.76.11.11.2.9.1

The configuration information for an Authenticator Port.

Indexes

dot1xAuthConfigPortNumber

Column	Syntax	OID
dot1xAuthConfigPortNumber A unique value for each port that correlates to port index. Its value ranges between 1 and the value of port number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.11.2.9.1.1
dot1xAuthConfigPortControl The current value of the controlled Port control parameter for the Port.	Enumerationr/w Enumerated Values: 1 forceUnauthorized 2 auto 3 forceAuthorized	.1.3.6.1.4.1.171.10.76.11.11.2.9.1.2
dot1xAuthConfigPortStatus The current value of the controlled Port status parameter for the Port.	Enumeration Enumerated Values: 1 authorized 2 unauthorized	.1.3.6.1.4.1.171.10.76.11.11.2.9.1.3
dot1xAuthConfigPortSessionTime The duration of the session in seconds.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.10.76.11.11.2.9.1.4
dot1xAuthConfigPortSessionUserName The User-Name representing the identity of the Supplicant PAE.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.76.11.11.2.9.1.5

A list of 802.1p port default priority Entries.

dot1pPortEntry row .1.3.6.1.4.1.171.10.76.11.12.3.1.1

A list of 802.1p port default priority priorities.

Indexes

dot1pPortIndex

Column	Syntax	OID
dot1pPortIndex A port identifier that is in the range of 1 to ifNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.12.3.1.1.1
dot1pPortPriority For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, D-Link Smart Switches will refer t…	Enumerationr/w Enumerated Values: 1 low 2 medium 3 high 4 highest	.1.3.6.1.4.1.171.10.76.11.12.3.1.1.2

A table to control the rate limiting parameters 
either for the entire switch or for each interface in the switch.

bandwidthCtrlEntry row .1.3.6.1.4.1.171.10.76.11.13.1.2.1

An entry appears in this table for each physical
interface in the switch.

Indexes

bandwidthCtrlIndex

Column	Syntax	OID
bandwidthCtrlIndex The interface index for which the configuration in this entry applies.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.13.1.2.1.1
bandwidthCtrlTxThreshold Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, th…	Integer32r/w Constraints: range: 64-1024000 range: 0-0	.1.3.6.1.4.1.171.10.76.11.13.1.2.1.2
bandwidthCtrlRxThreshold Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets…	Integer32r/w Constraints: range: 64-1024000 range: 0-0	.1.3.6.1.4.1.171.10.76.11.13.1.2.1.3

A table to configure trusted host in the system.

trustedHostEntry row .1.3.6.1.4.1.171.10.76.11.14.1.2.1

Each entry in this table represents rules for particular
trusted host.

Indexes

trustedHostIpAddr trustedHostIpMask

Column	Syntax	OID
trustedHostIpAddr The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.14.1.2.1.1
trustedHostIpMask Used to mask with IP address, it allow you set a subnet as a trusted host entry.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.14.1.2.1.2
trustedHostRowStatus The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.14.1.2.1.3

A table to control port security features of the device.

portSecEntry row .1.3.6.1.4.1.171.10.76.11.14.2.1.1

An entry appears in port security table for each interface
in the system.

Indexes

portSecIndex

Column	Syntax	OID
portSecIndex The interface index for which the configuration in this entry applies.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.14.2.1.1.1
portSecState Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.14.2.1.1.2
portSecMLA Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 6…	Integer32r/w Constraints: range: 0-64	.1.3.6.1.4.1.171.10.76.11.14.2.1.1.3

A table to control ARP Spoofing prevention for the entire 
switch or for each interface in the switch.

aRPSpoofPreventEntry row .1.3.6.1.4.1.171.10.76.11.14.3.1.1

An entry appears in this table for each interface
in the system.

Indexes

aRPSpoofPreventIpAddr

Column	Syntax	OID
aRPSpoofPreventIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.14.3.1.1.1
aRPSpoofPreventMacAddress Ethernet Mac Address.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.14.3.1.1.2
aRPSpoofPreventPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.14.3.1.1.3
aRPSpoofPreventRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.14.3.1.1.4

A table to ACL profile .

aclProfileEntry row .1.3.6.1.4.1.171.10.76.11.15.1.1.1

Each entry in this table is a ACL profile.
Index to the table is ACL profile ID.

Indexes

aclProfileNo

Column	Syntax	OID
aclProfileNo The ACL Profile ID. The ID 1 to 50 is user-defined ACL, and the ID more than 50 is reserved for system-defined ACL. The user only allow to create user-defined ACL ID. And system-defined ACL is read only.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.1
aclProfileType The ACL Profile type, possible value are l2 (1) - for MAC-based rule, l3 (2) - for IPv4-based rule, arpSP_permit(4) - for ARP Spoofing prevention entry, arpSP_deny(5) - for ARP Spoofing prevention entry, voiceVlan(6) -…	Enumerationr/w Enumerated Values: 1 l2 2 l3 4 arpSP-permit 5 arpSP-deny 6 voiceVlan	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.2
aclProfileRuleCount The number of rules in this profile.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.3
aclProfileMask Indicate which field want to care in the packet. Turn on the following bits to select the following items Type Item BIT ------------------------------------------ L2 DST_MAC …	OctetStringr/w	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.4
aclProfileDstMacAddrMask The ACL Profile destination MAC address mask. If DST_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleDstMacAddr, to caculate a range of MAC address which is really care.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.5
aclProfileSrcMacAddrMask The ACL Profile source MAC address mask. If SRC_MAC is turn on in aclProfileMask, it will work with its member rule field,aclL2RuleSrcMacAddr, to caculate a range of MAC address which is really care.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.6
aclProfileIPProtocol Indicate which IP Protocol will be care in this profile. Only profile type is l3 can set the IP protocol. For others, this field will be none.	Enumerationr/w Enumerated Values: 0 none 1 icmp 2 igmp 6 tcp 17 udp	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.7
aclProfileDstIpAddrMask The ACL Profile destination IP address mask. If DST_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleDstIpAddr, to caculate a range of IP address which is really care. The value is in …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.8
aclProfileSrcIpAddrMask The ACL Profile source IP address mask. If SRC_IP is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleSrcIpAddr, to caculate a range of IP address which is really care. The value is in HEX f…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.9
aclProfileDstPortMask The ACL Profile UDP/TCP destination port mask. If DST_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpDstPort, to caculate a range of destination port which is really care. Th…	OctetStringr/w	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.10
aclProfileSrcPortMask The ACL Profile UDP/TCP source port mask. If SRC_PORT is turn on in aclProfileMask, it will work with its member rule field,aclL3RuleTcpUdpSrcPort, to caculate a range of source port which is really care. The value is…	OctetStringr/w	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.11
aclProfileArpSenderMacAddrMask The ACL Profile Sender MAC mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.12
aclProfileArpSenderIpAddrMask The ACL Profile Sender IP mask. This is only for ARP Spoofing Prevention which is System-defined ACL, and it's not allow to modify. The value is in HEX format.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.13
aclProfileStatus This object indicates the status of this entry, can only be set to 'createAndWait','active' and 'destroy'. When the value of the entry status is 'createAndWait', it could be set to 'active' only if the three values of…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.15.1.1.1.14

A table to configure L2 filter rules in the system.

aclL2RuleEntry row .1.3.6.1.4.1.171.10.76.11.15.2.1.1

Each entry in this table is a L2 filter rule.
Index to the table is the L2 filter number and Profile ID.

Indexes

aclL2AccessID aclL2ProfileID

Column	Syntax	OID
aclL2AccessID L2 Filter rule ID.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.1
aclL2ProfileID ACL Profile ID which this rule join.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.2
aclL2RuleEtherType The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '-1', which means the rule don't care this condition.	Integer32r/w Constraints: range: 1501-65535 range: -1--1	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.3
aclL2RuleDstMacAddr Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero,which means the rule don't care this condition.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.4
aclL2RuleSrcMacAddr Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero, which means the rule don't care this condition.. address	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.5
aclL2RuleVlanId Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. By Default, the value will be '-1', which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-4094	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.6
aclL2Rule1pPriority 802.1p priority to be matched with the packet. By Default, the value will be '-1', which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-7	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.7
aclL2RuleDstMacAddrMask The MAC address Mask work for Destination MAC address. This field is read-only and copy from it's Profile setting.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.8
aclL2RuleSrcMacAddrMask The MAC address Mask work for Source MAC address. This field is read-only and copy from it's Profile setting.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.9
aclL2RuleInPortList Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.10
aclL2RuleAction Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded.	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.11
aclL2RuleStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.15.2.1.1.13

A table to configure L3 filter rules in the system.

aclL3RuleEntry row .1.3.6.1.4.1.171.10.76.11.15.3.1.1

Each entry in this table is a L3 filter rule.
Index to the table is L3 filter number.

Indexes

aclL3RuleAccessID aclL3RuleProfileNo

Column	Syntax	OID
aclL3RuleAccessID L3 Filter rule ID.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.1
aclL3RuleProfileNo The Profile ID which this rule join.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.2
aclL3RuleProtocol The type of protocol to be checked against the packet.	Enumeration Enumerated Values: 1 icmp 2 igmp 6 tcp 17 udp	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.3
aclL3RuleICMPMessageType The message type to be checked against the packet. If the message type matches with the packet, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1',which means…	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.4
aclL3RuleICMPMessageCode The message code to be checked against the packet. If the packet matches with the message code, then the packet will be dropped / allowed based on the action set in aclL3RuleAction. The default value is '-1', which mean…	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.5
aclL3RuleDstIpAddr Destination IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.6
aclL3RuleSrcIpAddr Source IP address to be matched with the packet. The default value will be zero, which means the rule don't care this condition.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.7
aclL3RuleDstIpAddrMask The IP subnet mask for Destination IP address. This field is read-only and copy from it's Profile setting.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.8
aclL3RuleSrcIpAddrMask The IP subnet mask for Source IP address. This field is read-only and copy from it's Profile setting.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.9
aclL3RuleTcpUdpDstPort The TCP / UDP destination port. The default value is -1, which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-65535	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.10
aclL3RuleTcpUdpSrcPort The TCP / UDP source port. The default value is -1, which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-65535	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.11
aclL3RuleTcpUdpDstPortMask The TCP / UDP Destination port Mask. This field is read-only and copy from it's Profile setting.	OctetString	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.12
aclL3RuleTcpUdpSrcPortMask The TCP / UDP Source port Mask. This field is read-only and copy from it's Profile setting.	OctetString	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.13
aclL3RuleTcpAckBit The TCP ACK bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.14
aclL3RuleTcpRstBit The TCP RST bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.15
aclL3RuleTcpUrgBit The TCP Urg bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.16
aclL3RuleTcpPshBit The TCP Psh bit to be checked against the packet. The default value is 'dont-care'(-1). which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.17
aclL3RuleTcpSynBit The TCP Syn bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.18
aclL3RuleTcpFinBit The TCP Fin bit to be checked against the packet. The default value is 'dont-care'(-1), which means the rule don't care this condition.	Enumerationr/w Enumerated Values: -1 dont-care 1 establish 2 notEstablish	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.19
aclL3RuleDscp The IP Dscp value to be checked against the packet. A default value is '-1', which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-63	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.20
aclL3RuleIgmpType The IGMP Type to be checked against the packet.A default value is '-1', which means the rule don't care this condition.	Integer32r/w Constraints: range: -1-255	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.21
aclL3RulePortList Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.22
aclL3RuleAction Specifies the action to be taken on the packet if the filter rule matches.	Enumerationr/w Enumerated Values: 1 allow 2 drop	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.23
aclL3RuleStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.15.3.1.1.25

A table to control Loopback detection features either for 
the entire switch or for each interface in the switch.

sysLBDCtrlEntry row .1.3.6.1.4.1.171.10.76.11.17.4.1

An entry appears in this table for each interface
in the system.

Indexes

sysLBDCtrlIndex

Column	Syntax	OID
sysLBDCtrlIndex The interface index of the port for which the configuration in this entry applies.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.76.11.17.4.1.1
sysLBDPortStatus Provides control to per port enable or disable the loopback detection function. Default is disabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.17.4.1.2
sysLBDPortLoopStatus The loop status for this port.	Enumeration Enumerated Values: 1 normal 2 disabled	.1.3.6.1.4.1.171.10.76.11.17.4.1.3

A table that contains Voice Vlan Port Control
configuration information.

voicevlanPortControlEntry row .1.3.6.1.4.1.171.10.76.11.21.1.6.1

A list of Voice Vlan Control configuration
parameters for each Port on this device.

Indexes

voicevlanPortControlIndex

Column	Syntax	OID
voicevlanPortControlIndex The voice vlan port index.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.76.11.21.1.6.1.1
voicevlanPortAutoDetection This object is for enabling or disabling Voice Vlan Auto Detection in the port. If the auto detection is enable, switch will add this port to the voice VLAN automatically if it detects the device OUI matches the Tele…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.76.11.21.1.6.1.2
voicevlanPortState This object indicates Voice vlan state to this Port. manual - this port is a static member of voice vlan. dynamic - this port is a dynamic member of voice vlan. none - this port is not a member of voice vlan.	Enumeration Enumerated Values: 1 manual 2 dynamic 3 none	.1.3.6.1.4.1.171.10.76.11.21.1.6.1.3

A voice vlan OUI entry containing the description and mac.

voicevlanOUIEntry row .1.3.6.1.4.1.171.10.76.11.21.2.1.1

A voice vlan OUI entry containing the description and mac.

Indexes

voicevlanOUITelephonyOUI

Column	Syntax	OID
voicevlanOUITelephonyOUI An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object ind…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.21.2.1.1.1
voicevlanOUIDescription The Description for the OUI.	OctetStringr/w	.1.3.6.1.4.1.171.10.76.11.21.2.1.1.2
voicevlanOUIMask Voice vlan OUI Mask. Always be FF:FF:FF:00:00:00.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.21.2.1.1.3
voicevlanOUIStatus This object indicates the status of this entry. To create a new entry, you must set the voicevlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.21.2.1.1.4

A Auto Surveillance vlan OUI entry containing the description and mac.

autoSurveillanceVlanOUIEntry row .1.3.6.1.4.1.171.10.76.11.26.2.1.1

A Auto Surveillance vlan OUI entry containing the description and mac.

Indexes

autoSurveillanceVlanOUISurveillanceOUI

Column	Syntax	OID
autoSurveillanceVlanOUISurveillanceOUI An Organizationally Unique Identifier (OUI) is a 24-bit number that is purchased from the IEEE Registration Authority. This identifier uniquely identifies a vendor, manufacturer, or other organization. This object ind…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.26.2.1.1.1
autoSurveillanceVlanOUIDescription The Description for the OUI.	OctetStringr/w	.1.3.6.1.4.1.171.10.76.11.26.2.1.1.2
autoSurveillanceVlanOUIMask Auto Surveillance vlan OUI Mask. In default OUI is FF:FF:FF:F0:00:00, in user define OUI is FF:FF:FF:FF:FF:FF.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.76.11.26.2.1.1.3
autoSurveillanceVlanOUIComponentType This object indicates the Component Type of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIComponentType to be CreateAndGo, then this entry will turn to be Active.	Enumerationr/w Enumerated Values: 0 video-Management-Server 1 vMS-Client 2 video-Encoder 3 network-Storage 4 other-IP-Surveillance-Devices 5 d-Link-Surveillance-Device	.1.3.6.1.4.1.171.10.76.11.26.2.1.1.4
autoSurveillanceVlanOUIStatus This object indicates the status of this entry. To create a new entry, you must set the autoSurveillanceVlanOUIStatus to be CreateAndGo, then this entry will turn to be Active.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.76.11.26.2.1.1.5