DES-1210-10AXME Table View

A table to control the port specific parameters of the device like speed,
duplex mode, etc.

sysPortCtrlEntry row .1.3.6.1.4.1.171.10.75.14.1.13.1

An entry appears in this table for each interface in the system.

Index to the table is the interface index of the port.

Indexes

sysPortCtrlIndex sysPortCtrlMediumType

Column	Syntax	OID
sysPortCtrlIndex Interface index of the port for the configuration in this entry applies.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.1.13.1.1
sysPortCtrlMediumType This object indicates the port type: fiber 1G/100M or copper.	Enumeration Enumerated Values: 100 copper 101 fiber1G 102 fiber100M	.1.3.6.1.4.1.171.10.75.14.1.13.1.2
sysPortCtrlSpeed Configures interface speed.	Enumerationr/w Enumerated Values: 1 rate1000M-Full 2 rate100M-Full 3 rate100M-Half 4 rate10M-Full 5 rate10M-Half 6 auto 7 disable	.1.3.6.1.4.1.171.10.75.14.1.13.1.3
sysPortCtrlOperStatus The port's operating speed state.	Enumeration Enumerated Values: 1 down 2 rate1000M-Full 3 rate100M-Full 4 rate100M-Half 5 rate10M-Full 6 rate10M-Half	.1.3.6.1.4.1.171.10.75.14.1.13.1.4
sysPortCtrlMDI Configures interface auto/mdi/mdix mode. The default setting is Auto.	Enumerationr/w Enumerated Values: 1 auto 2 mdi 3 mdix	.1.3.6.1.4.1.171.10.75.14.1.13.1.5
sysPortCtrlFlowControl Enables / disables flow control for the interface.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.171.10.75.14.1.13.1.6
sysPortCtrlFlowControlOper The link parner negotiate port's operating flow control state.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.1.13.1.7
sysPortCtrlType The port's media type.	Enumeration Enumerated Values: 1 fastethernet 2 gigabitethernet 3 fiberwith100BaseSFPModule 4 fiberwith1000BaseSFPModule	.1.3.6.1.4.1.171.10.75.14.1.13.1.8

The port description table.

sysPortDescriptionEntry row .1.3.6.1.4.1.171.10.75.14.1.14.1

The port description entry.

Indexes

sysPortDescIndex sysPortDescMediumType

Column	Syntax	OID
sysPortDescIndex This object indicates the port index.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.171.10.75.14.1.14.1.1
sysPortDescMediumType This object indicates the port type: fiber 1G/100M or copper.	Enumeration Enumerated Values: 100 copper 101 fiber1G 102 fiber100M	.1.3.6.1.4.1.171.10.75.14.1.14.1.2
sysPortDescString This object indicates the port description.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.75.14.1.14.1.3

The port error table.

sysPortErrEntry row .1.3.6.1.4.1.171.10.75.14.1.15.1

A list of information for the err port of the device.

Indexes

sysPortErrPortIndex

Column	Syntax	OID
sysPortErrPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.171.10.75.14.1.15.1.1
sysPortErrPortState This object decides whether the port state is enabled or disabled.	Enumeration Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.171.10.75.14.1.15.1.2
sysPortErrPortStatus This object decides whether the PortStatus is err-disabled.	Enumeration Enumerated Values: 1 other 2 err-disabled	.1.3.6.1.4.1.171.10.75.14.1.15.1.3
sysPortErrPortReason This object decides whether the PortStatus is LBD.	Enumeration Enumerated Values: 1 lbd	.1.3.6.1.4.1.171.10.75.14.1.15.1.4

A table that contains port-specific information
for the Spanning Tree Protocol.

stpPortEntry row .1.3.6.1.4.1.171.10.75.14.6.2.1

A list of information maintained by every port
about the Spanning Tree Protocol state for that
port.

Indexes

stpPort

Column	Syntax	OID
stpPort The Port number of the port for which this entry contains spanning tree information.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.6.2.1.1
stpPortStatus Current state of the Port which can be changed to either Disabled or Enabled for ALL spanning tree instances. Setting this object will override the port's status in any of the MSTI contexts	Enumerationr/w Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.171.10.75.14.6.2.1.2
stpPortPriority The four most significant bits of the Port Identifier of the Spanning Tree instance can be modified by setting the CistPortPriority value. The values that are set for Port Priority must be in steps of 16.	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.171.10.75.14.6.2.1.3
stpAdminPortPathCost The contribution of this port to the path cost of paths towards the spanning tree root which include this port. Writing a value of '0' assigns the automatically calculated default Path Cost value to the ohter object …	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.171.10.75.14.6.2.1.4
stpPortPathCost The contribution of this port to the path cost of paths towards the CIST Root which include this port.	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.171.10.75.14.6.2.1.5
stpPortProtocolMigration Indicates the Protocol migration state of this Port. When operating in RSTP/MSTP (version >= 2) mode, writing TRUE(1) to this object forces this port to transmit MSTP BPDUs without instance information. Any o…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.75.14.6.2.1.6
stpPortEdge This parameter when TRUE(1) indicates that detection of a port as Edge Port happens automatically and FALSE(2) indicates that this feature is disabled.	Enumerationr/w Enumerated Values: 0 false 1 true 2 auto	.1.3.6.1.4.1.171.10.75.14.6.2.1.7
stpPortAdminP2P The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.171.10.75.14.6.2.1.8
stpPortRestrictedRole A Boolean value set by management. If TRUE causes the Port not to be selected as Root Port for the CIST or any MSTI, even it has the best spanning tree priority vector. Such a Port will be selected as an Alternate Po…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.75.14.6.2.1.9
stpPortRestrictedTCN A Boolean value set by management. If TRUE causes the Port not to propagate received topology change notifications and topology changes to other Ports. This parameter should be FALSE by default. If set it can cause t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.10.75.14.6.2.1.10
stpPortHelloTime The amount of time between the transmission of Configuration bridge PDUs by this node in units of hundredths of a second.	Timeoutr/w Constraints: range: 100-1000 Description: A STP timer in units of 1/100 seconds To convert a Timeout value into a value in units of 1/256 seconds, the following algorithm should be used: b = floor( (n * 256) / 100) where: …	.1.3.6.1.4.1.171.10.75.14.6.2.1.11
stpPortState Current state of the Port as defined by the Common spanning tree protocol.	Enumeration Enumerated Values: 1 disabled 2 discarding 4 learning 5 forwarding	.1.3.6.1.4.1.171.10.75.14.6.2.1.12
stpPortFowardBPDU This object is for enabling or disabling forward BPDU.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.6.2.1.13

This table contains one entry for each instance of MSTP. 
This table maintains context ID as one more index to 
support Multiple Instances.

mstVlanMstiMappingEntry row .1.3.6.1.4.1.171.10.75.14.6.3.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceIndex

Column	Syntax	OID
mstInstanceIndex An arbitrary integer within the range from 1 to the value of Max Instance Number that uniquely identifies an instance.	Integer32 Constraints: range: 1-15	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.1
mstSetVlanList A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to …	OctetStringr/w Constraints: range: 0-512	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.2
mstResetVlanList A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to …	OctetStringr/w Constraints: range: 0-512	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.3
mstInstanceVlanMapped A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with VlanIndex values 1 through 8; the second octet to VLANs 9 through 16 etc. The most significant bit of each octet corresponds to …	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.4
mstInstanceVlanMapped2k A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.5
mstInstanceVlanMapped3k A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.6
mstInstanceVlanMapped4k A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.171.10.75.14.6.3.7.1.7

Table containing Bridge Information specific to Spanning 
Tree Instance. This table maintains context ID as one 
more index to support Multiple Instances.

mstMstiBridgeEntry row .1.3.6.1.4.1.171.10.75.14.6.4.3.1

Entry indicating the Bridge Information.

Indexes

mstMstiInstanceIndex

Column	Syntax	OID
mstMstiInstanceIndex Spanning Tree Instance to which the information belongs.	Integer32 Constraints: range: 1-15	.1.3.6.1.4.1.171.10.75.14.6.4.3.1.1
mstMstiBridgePriority The writable portion of the MSTI Bridge Identifier. comprising of the first two octets. The values that are set for Bridge Priority must be in steps of 4096.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.171.10.75.14.6.4.3.1.2
mstMstiStatus The administrative status requested by management for the MST feature. The value enabled(1) indicates that Mst should be enabled in the device on all ports. The value disabled(2) indicates that Mst should be disabl…	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.6.4.3.1.3

This table contains Common Spanning Tree Port
Information.

mstCistPortEntry row .1.3.6.1.4.1.171.10.75.14.6.5.1.1

A list of information maintained by every port for
Common Spanning tree.

Indexes

mstCistPort

Column	Syntax	OID
mstCistPort The Port number of the port for which this entry contains spanning tree information.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.1
mstCistPortDesignatedBridge The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.	BridgeId Type Constraints: range: 8 Description: The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to ref…	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.2
mstCistPortAdminPathCost The contribution of this port to the path cost of paths towards the MSTI Root which include this port.	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.3
mstCistPortPathCost The contribution of this port to the path cost of paths towards the MSTI Root which include this port.	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.4
mstCistPortPriority The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priori…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.5
mstCistForcePortState Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' fo…	Enumeration Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.6
mstCistCurrentPortRole Current Port Role of the port for this spanning tree instance.	Enumeration Enumerated Values: 0 disabled 1 alternate 2 backup 3 root 4 designated 5 master	.1.3.6.1.4.1.171.10.75.14.6.5.1.1.7

This table contains Spanning Tree Instance Specific Port
Information.

mstMstiPortEntry row .1.3.6.1.4.1.171.10.75.14.6.5.2.1

A list of information maintained by every port for each
and every spanning tree instance.

Indexes

mstMstiPort mstInstanceIndex

Column	Syntax	OID
mstMstiPort The Port number of the port for which this entry contains spanning tree information.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.1
mstMstiPortDesignatedBridge The unique Bridge Identifier of the bridge which this port considers to be the Designated Bridge for the port's segment.	BridgeId Type Constraints: range: 8 Description: The Bridge-Identifier as used in the Spanning Tree Protocol to uniquely identify a bridge. Its first two octets (in network byte order) contain a priority value and its last 6 octets contain the MAC address used to ref…	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.2
mstMstiPortAdminPathCost The contribution of this port to the path cost of paths towards the MSTI Root which include this port.	Integer32r/w Constraints: range: 0-200000000	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.3
mstMstiPortPathCost The contribution of this port to the path cost of paths towards the MSTI Root which include this port.	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.4
mstMstiPortPriority The four most significant bits of the Port Identifier for a given Spanning Tree instance can be modified independently for each Spanning Tree instance supported by the Bridge. The values that are set for Port Priori…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.5
mstMstiForcePortState Current state of the Port which can be changed to either Disabled or Enabled for the specific spanning tree instance. This object can be set to enabled only if the 'fsMIMstCistForcePortState' is set to 'enabled' fo…	Enumeration Enumerated Values: 0 disabled 1 enabled	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.6
mstMstiCurrentPortRole Current Port Role of the port for this spanning tree instance.	Enumeration Enumerated Values: 0 disabled 1 alternate 2 backup 3 root 4 designated 5 master	.1.3.6.1.4.1.171.10.75.14.6.5.2.1.7

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

dot1qVlanEntry row .1.3.6.1.4.1.171.10.75.14.7.6.1

Information for a VLAN configured into the
device by (local or network) management.

Indexes

dot1qVlanName

Column	Syntax	OID
dot1qVlanName An administratively assigned string, which may be used to identify the VLAN.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.171.10.75.14.7.6.1.1
dot1qVlanEgressPorts The set of ports which are permanently assigned to the egress list for this VLAN by management. Changes to a bit in this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVR…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.7.6.1.2
dot1qVlanForbiddenPorts The set of ports which are prohibited by management from being included in the egress list for this VLAN. Changes to this object that cause a port to be included or excluded affect the per-port per-VLAN Registrar contro…	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.7.6.1.3
dot1qVlanUntaggedPorts The set of ports which should transmit egress packets for this VLAN as untagged. The default value of this object for the default VLAN (dot1qVlanIndex = 1) is a string of appropriate length including all ports. There …	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.7.6.1.4
dot1qVlanAdvertisementStatus Enable/Disable Advertisement Status of the IEEE 802.1Q VLAN.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.7.6.1.5
dot1qVlanRowStatus The status of a row in dot1qVlanTable. By setting this object, new entries can be created in dot1qVlanTable and existing entries can be removed from dot1qVlanTable. It can be used as specified in the SNMP v2 standard.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.7.6.1.6

This table contains the list of ports through which 
a router, in a particular VLAN is reachable.

dot1qVlanUngisterMCFilterEntry row .1.3.6.1.4.1.171.10.75.14.7.8.1

A list of multicast filter mode information for each VLAN ID.

Indexes

dot1qVlanUngisterMCFilterVlanId

Column	Syntax	OID
dot1qVlanUngisterMCFilterVlanId Per Vlan to configure multicast filtering function.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.7.8.1.1
dot1qVlanUngisterMCFiltermode Filter unknown multicast frames or normal operation(i.e. forwarding)	Enumerationr/w Enumerated Values: 0 forward 1 filter	.1.3.6.1.4.1.171.10.75.14.7.8.1.2

A Port-channel is created through ifMain table.
After the creation of the port-channel, corresponding logical
interface will be created in the ifMain table. 
This Port-channel table is indexed through Key values and allows to 
configure link selection policy and the Mac address for 
the port-channel. All other objects in this table displays 
the details of the port-channel.

laPortChannelEntry row .1.3.6.1.4.1.171.10.75.14.8.1.3.1

There is one entry in this table for each created
port-channel port.

Indexes

laPortChannelIfIndex

Column	Syntax	OID
laPortChannelIfIndex The index of the port-channel(Aggregator's interface index).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.75.14.8.1.3.1.1
laPortChannelMemberList Member Port list of the port channel. Add the ports as a aggregation member associated of a port-channel.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.8.1.3.1.2
laPortChannelMode Current Operating Channel Mode of the port channel Lacp(1) - forcing the port to negotiate with the partner. manual(2) - force the port to enable channeling (Manual). disable(3) - channeling is disabled.	PortLaModer/w Type Values: 1 lacp 2 static 3 disable Description: Defines how a Port Channel does channeling. lacp(1) - place the port into passive negotiation state, in which the port waits for its peer to initiate negotiation. s…	.1.3.6.1.4.1.171.10.75.14.8.1.3.1.3
laPortChannelMasterPort The master port of the port-channel.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.75.14.8.1.3.1.4

A table that contains Link Aggregation Control
configuration information about every
Aggregation Port associated with this device.
A row appears in this table for each physical port.

laPortControlEntry row .1.3.6.1.4.1.171.10.75.14.8.2.1.1

A list of Link Aggregation Control configuration
parameters for each Aggregation Port on this device.

Indexes

laPortControlIndex

Column	Syntax	OID
laPortControlIndex The index of the port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.75.14.8.2.1.1.1
laPortActorPortPriority The priority value assigned to this Aggregation Port. This 16-bit value is read-write.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.10.75.14.8.2.1.1.2
laPortActorActivity This object indicates LACP-Activity to this Aggregation Port. LACP can be configured in one of two modes: active or passive. In active mode it will always send frames along the configured links. If the actor and part…	Enumerationr/w Enumerated Values: 1 active 2 passive	.1.3.6.1.4.1.171.10.75.14.8.2.1.1.3
laPortActorTimeout This object indicates LACP-Timeout to this Aggregation Port. short(1) - LACP Timeout 3 seconds. long (2) - LACP Timeout 90 seconds.	Enumerationr/w Enumerated Values: 1 short 2 long	.1.3.6.1.4.1.171.10.75.14.8.2.1.1.4

A list of the Static MACs

staticEntry row .1.3.6.1.4.1.171.10.75.14.9.3.1

A Static MAC entry containing the mac and forwarding port.

Indexes

staticVlanID staticMac staticPort

Column	Syntax	OID
staticVlanID The VLAN ID of the static MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.9.3.1.1
staticMac The MAC address associated of the static MAC entry.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.9.3.1.2
staticPort The forwarding port of the static MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.9.3.1.3
staticStatus The status of an entry in the Static MAC Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available. The trunk member port can not set up static MAC.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.9.3.1.4

This table contains the list of ports through which 
a router, in a particular VLAN is reachable.

igsVlanRouterEntry row .1.3.6.1.4.1.171.10.75.14.10.3.3.1

Contains the VLAN ID and list of ports on which
routers are present in the VLAN.

Indexes

igsVlanRouterVlanId

Column	Syntax	OID
igsVlanRouterVlanId VLAN ID of the ports through which router is reachable.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.10.3.3.1.1
igsVlanRouterPortList List of ports on which routers are present. These router ports are learnt through control messages received from routers, and can also be configured statically.	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.10.3.3.1.2

This table contains configuration of snooping
on specific Vlans. This Table is valid only when VLAN is  
enabled in the system.

igsVlanFilterEntry row .1.3.6.1.4.1.171.10.75.14.10.3.4.1

Contains snooping status , version and fast leave
configuration for a specific VLAN.

Indexes

igsVlanFilterVlanId

Column	Syntax	OID
igsVlanFilterVlanId Index of IgsVlanFilterEntry. This object indicates the VLAN ID for which the snooping configurations in IgsVlanFilterEntry is to be done.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.1
igsVlanSnoopStatus This object allows you to enable/disable IGS function on a specific VLAN.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.2
igsVlanQuerier Indicates whether the switch is configured as a querier in the VLAN	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.3
igsVlanCfgQuerier The snooping switch can be configured as a querier via this object to send out IGMP general queries when IGMP routers are not present in the VLAN. When set to 'enabled', the switch will generate general queries.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.4
igsVlanQueryInterval This is the interval (in seconds) for which the switch sends general queries when it is configured as a querier for the VLAN. A switch should be configured as a querier for a VLAN only when there is no queriers in th…	Integer32 Constraints: range: 60-600	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.5
igsVlanRtrPortList List of ports which are configured statically as router ports	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.6
igsVlanFbdRtrPortList List of ports which can be configured statically as forbidden router ports.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.7
igsVlanFastLeave Enables or disables fast leave for the VLAN. When it is 'disabled',on reception of a leave message, the switch checks if they are any interested receivers for the group by sending a group specific query before removin…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.10.3.4.1.8

This table contains MAC based multicast forwarding 
information.

igsVlanMulticastGroupEntry row .1.3.6.1.4.1.171.10.75.14.10.3.5.1

This table contains VLAN ID, multicast group MAC address and the
list of ports onto which the multicast data packets for group
should be forwarded.

Indexes

igsVlanMulticastGroupVlanId igsVlanMulticastGroupIpAddress

Column	Syntax	OID
igsVlanMulticastGroupVlanId VLAN ID pertaining to the Multicast forwarding entry	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.10.3.5.1.1
igsVlanMulticastGroupIpAddress Multicast group IP address. This object indicates that a multicast group address was learned in the switch and be represented as IP address format.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.171.10.75.14.10.3.5.1.2
igsVlanMulticastGroupMacAddress Multicast group MAC address. This object indicates that a multicast group address was learned in the switch and be represented as MAC address format.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.10.3.5.1.3
igsVlanMulticastGroupPortList List of ports onto which the multicast data packets destined for this group will be forwarded.	PortList Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.10.3.5.1.4

This table is used to manage the IGMP Authentication
function of the switch.

igsAccessAuthEntry row .1.3.6.1.4.1.171.10.75.14.10.5.1.1

Contains management entities for IGMP Authentication
function.

Indexes

igsAccessAuthPortIndex

Column	Syntax	OID
igsAccessAuthPortIndex The port index of igsAccessAuthTable which indicates the port to be configured.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.10.5.1.1.1
igsAccessAuthState This object can be configured to set IGMP Authentication state to enabled/disabled on each port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.10.5.1.1.2

A table containing static configuration information for
each GVRP configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

gvrpSettingsEntry row .1.3.6.1.4.1.171.10.75.14.11.5.1

Information for a GVRP configured into the
device by (local or network) management.

Indexes

gvrpSettingsPortControlIndex

Column	Syntax	OID
gvrpSettingsPortControlIndex The index of the port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.75.14.11.5.1.1
gvrpSettingsPVID The PVID value assigned to this Aggregation Port. This 16-bit value is read-write.	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.11.5.1.2
gvrpSettingsGVRPState Enable/Disable GVRP State to this Aggregation Port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.11.5.1.3
gvrpSettingsIngressChecking Enable/Disable Ingress Checking mechanism of GVRP to this Aggregation Port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.11.5.1.4
gvrpSettingsAcceptableFrameType Chose types All Frames/Tagged to this Aggregation Port.	Enumerationr/w Enumerated Values: 1 allFrames 2 taggedOnly	.1.3.6.1.4.1.171.10.75.14.11.5.1.5

A list of cosOutputSchedule.

cosClassEntry row .1.3.6.1.4.1.171.10.75.14.12.2.1.1

A list of cosOutputClass Weight.

Indexes

cosClassIndex

Column	Syntax	OID
cosClassIndex A index of class 0 ~ 3.	Integer32 Constraints: range: 0-3	.1.3.6.1.4.1.171.10.75.14.12.2.1.1.1
cosWeight cos weight	Integer32r/w Constraints: range: 1-55	.1.3.6.1.4.1.171.10.75.14.12.2.1.1.2

A list of port mapping priority Entries.

portMapPriEntry row .1.3.6.1.4.1.171.10.75.14.12.3.1.1

A list of 802.1p port mapping priority priorities.

Indexes

portMapPriPortIndex

Column	Syntax	OID
portMapPriPortIndex A port identifier that is in the range of 1 to ifNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.12.3.1.1.1
portMapPriClass For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization. For ingress tagged packets, if 802.1p not enabled D-Link Smar…	Enumerationr/w Enumerated Values: 0 low 1 medium 2 high 3 highest	.1.3.6.1.4.1.171.10.75.14.12.3.1.1.2

A list of 802.1p port default priority Entries.

qosDefaultUserPriEntry row .1.3.6.1.4.1.171.10.75.14.12.4.1.1

A list of 802.1p port default priority priorities.

Indexes

qosDefaultUserPriPortIndex

Column	Syntax	OID
qosDefaultUserPriPortIndex A port identifier that is in the range of 1 to ifNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.12.4.1.1.1
qosDefaultPriority For ingress untagged packets, the per port 'Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.	Enumerationr/w Enumerated Values: 0 priority0 1 priority1 2 priority2 3 priority3 4 priority4 5 priority5 6 priority6 7 priority7	.1.3.6.1.4.1.171.10.75.14.12.4.1.1.2
qosEffectiveDefaultPriority For ingress untagged packets, the per port 'Effective Default Priority' setting will be applied to packets of each port to provide port-based traffic prioritization when 802.1p is enabled.	Enumeration Enumerated Values: 0 priority0 1 priority1 2 priority2 3 priority3 4 priority4 5 priority5 6 priority6 7 priority7	.1.3.6.1.4.1.171.10.75.14.12.4.1.1.3

A table mapping evaluated User Priority to Traffic
Class, for forwarding by the bridge.  Traffic class is a
number in the range (0..3).

qosUserPriEntry row .1.3.6.1.4.1.171.10.75.14.12.5.1.1

User Priority to Traffic Class mapping.

Indexes

qosUserPriIndex

Column	Syntax	OID
qosUserPriIndex For ingress tagged packets, D-Link Smart Switches will refer to these information and prioritize them with 4 different priority queues. If 802.1p is enabled.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.10.75.14.12.5.1.1.1
qosUserPriClass The User Class the received frame is mapped to.	Enumerationr/w Enumerated Values: 0 low 1 medium 2 high 3 highest	.1.3.6.1.4.1.171.10.75.14.12.5.1.1.2

A list of port priority settings.

qosPriSettingsEntry row .1.3.6.1.4.1.171.10.75.14.12.7.1.1

A list of port priority settings Entries.

Indexes

qosPriSetPortIndex

Column	Syntax	OID
qosPriSetPortIndex A port identifier that is in the range of 1 to ifNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.12.7.1.1.1
qosPriSetPortType The port priority setting type. (ex. none = 0, port mapping = 1, 802.1p = 2, DSCP = 4. If you want enable 802.1p & DSCP, the value is 2 + 4 = 6.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.171.10.75.14.12.7.1.1.2

A list of priority by acl setting.

aclQosEntry row .1.3.6.1.4.1.171.10.75.14.12.8.1.1

A list of priority by acl setting entry.

Indexes

aclQosIndex

Column	Syntax	OID
aclQosIndex Index of priority by acl setting.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.1
aclQosType Type of priority by acl setting.	Enumerationr/w Enumerated Values: 0 mac 1 ip 2 tcp 3 udp 4 vlanid 5 protocol	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.2
aclQosMACAddr Dst MAC of priority by acl setting.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.3
aclQosIPAddr Dst IP of priority by acl setting	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.4
aclQosTCPUDPPort Dst TCP/UDP port of priority by acl setting	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.5
aclQosVlanID VLAN ID of priority by acl setting	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.6
aclQosProtocol Ip protocol number of priority by acl setting	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.7
aclQosAssignClass Be mapped class of priority by acl setting.	Enumerationr/w Enumerated Values: 0 class0 1 class1 2 class2 3 class3	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.8
aclQosStatus Status of priority by acl setting.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.12.8.1.1.9

A table to control the rate limiting parameters 
either for the entire switch or for each interface in the switch.

bandwidthCtrlEntry row .1.3.6.1.4.1.171.10.75.14.13.1.2.1

An entry appears in this table for each physical
interface in the switch.

Indexes

bandwidthCtrlIndex

Column	Syntax	OID
bandwidthCtrlIndex The interface index for which the configuration in this entry applies.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.13.1.2.1.1
bandwidthCtrlTxThreshold Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, th…	Integer32r/w Constraints: range: 0-0 range: 64-1024000	.1.3.6.1.4.1.171.10.75.14.13.1.2.1.2
bandwidthCtrlRxThreshold Allows to configure the limiting value for the maximum number of receive packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for receive packets…	Integer32r/w Constraints: range: 0-0 range: 64-1024000	.1.3.6.1.4.1.171.10.75.14.13.1.2.1.3

The traffic control table.

trafficCtrlEntry row .1.3.6.1.4.1.171.10.75.14.13.4.2.1

The traffic control entry.

Indexes

trafficCtrlIndex

Column	Syntax	OID
trafficCtrlIndex The traffic control index.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.1
trafficCtrlActionMode The action mode of traffic control.	Enumerationr/w Enumerated Values: 0 drop 1 shutdown	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.2
trafficCtrlType The control type of traffic control. (b: Broadcast, m: Multicast, u: Unknown Unicast)	Enumerationr/w Enumerated Values: 0 none 1 b 2 m 3 mb 4 u 5 ub 6 um 7 umb	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.3
trafficCtrlThreshold The threshold of traffic control.	Integer32r/w Constraints: range: 1-102400	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.4
trafficCtrlCountDown The count down value of traffic control.	Integer32r/w Constraints: range: 0-30	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.5
trafficCtrlTimeInterval The time interval of traffic control.	Integer32r/w Constraints: range: 5-30	.1.3.6.1.4.1.171.10.75.14.13.4.2.1.6

A table to configure trusted host in the system.

trustedHostEntry row .1.3.6.1.4.1.171.10.75.14.14.1.2.1

Each entry in this table represents rules for particular
trusted host.

Indexes

trustedHostIpAddr trustedHostIpMask

Column	Syntax	OID
trustedHostIpAddr The IP address of host you allow to access to D-Link Smart Switch. Your local host IP Addresses must be one of the IP Addresses to avoid disconnection.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.1.2.1.1
trustedHostIpMask Used to mask with IP address, it allow you set a subnet as a trusted host entry.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.1.2.1.2
trustedHostRowStatus The status of an entry in the Trusted Host Table. Only a subset of the rowstatus variables (active, createAndGo, destroy) are available.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.1.2.1.3

A table to control port security features of the device.

portSecEntry row .1.3.6.1.4.1.171.10.75.14.14.2.1.1

An entry appears in port security table for each interface
in the system.

Indexes

portSecIndex

Column	Syntax	OID
portSecIndex The interface index for which the configuration in this entry applies.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.2.1.1.1
portSecState Enable / disable port security admin state for the interface. A given ports' dynamic MAC address learning will be stopped such that the current source MAC addresses entered into the MAC address forwarding…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.10.75.14.14.2.1.1.2
portSecMLA Configures interface port security maximum learning address numbers. When given ports' admin state is enabled, allows forwarding table learning address number. The number can be set 0 to 6…	Integer32r/w Constraints: range: 0-64	.1.3.6.1.4.1.171.10.75.14.14.2.1.1.3
portSecLockAddrMode Configures port security lock address mode for the interface. deleteOnReset : The locked addresses will not age out until the Switch has been reset. deleteOnTimeout : The locked addresses will age out aft…	Enumerationr/w Enumerated Values: 1 deleteOnReset 2 deleteOnTimeout 3 permanent	.1.3.6.1.4.1.171.10.75.14.14.2.1.1.4

A table to control port security FDB Permanent of the device.

portSecFDBPermanentEntry row .1.3.6.1.4.1.171.10.75.14.14.2.2.1

An entry appears in port security table for each interface
in the system.

Indexes

portSecFDBPermPort portSecFDBPermIndex

Column	Syntax	OID
portSecFDBPermIndex The index of the port security MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.2.2.1.1
portSecFDBPermVlanID The VLAN ID of the port security MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.2.2.1.2
portSecFDBPermMac The MAC address associated of the port security MAC entry.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.14.2.2.1.3
portSecFDBPermPort The forwarding port of the port security MAC entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.2.2.1.4

A table to control ARP Spoofing prevention for the entire 
switch or for each interface in the switch.

aRPSpoofPreventEntry row .1.3.6.1.4.1.171.10.75.14.14.3.1.1

An entry appears in this table for each interface
in the system.

Indexes

aRPSpoofPreventIpAddr

Column	Syntax	OID
aRPSpoofPreventIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.3.1.1.1
aRPSpoofPreventMacAddress Ethernet Mac Address.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.14.3.1.1.2
aRPSpoofPreventPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.14.3.1.1.3
aRPSpoofPreventRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.3.1.1.4

A table to control IP-MAC-Port Binding features either for the entire 
switch or for each interface in the switch.
          
Parameters in this table are valid only when the 
'issIpMacPortStatus' for the switch is not 'disabled'.

ipMacPortBindingEntry row .1.3.6.1.4.1.171.10.75.14.14.4.5.1

An entry appears in this table for each interface
in the system.

Indexes

ipMacPortBindingIpAddr ipMacPortBindingMacAddress

Column	Syntax	OID
ipMacPortBindingIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.4.5.1.1
ipMacPortBindingMacAddress Ethernet Mac Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.14.4.5.1.2
ipMacPortBindingPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.14.4.5.1.3
ipMacPortBindingRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.4.5.1.5

An entry appears in this table for each interface 
in the system.

macBlockListEntry row .1.3.6.1.4.1.171.10.75.14.14.4.6.1

An entry appears in this table for each interface
in the system.

Indexes

macBlockListMacAddr macBlockListVLANID macBlockListPort

Column	Syntax	OID
macBlockListMacAddr Blocked Mac Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.14.4.6.1.1
macBlockListVLANID Blocked IP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.4.6.1.2
macBlockListPort Blocked port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.10.75.14.14.4.6.1.3
macBlockListRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.4.6.1.4

A table to control filter DHCP Server for the entire
switch or for each interface in the switch.

filterDHCPServerEntry row .1.3.6.1.4.1.171.10.75.14.14.7.2.1

An entry appears in this table for each interface
in the system.

Indexes

filterDHCPServerIpAddr filterDHCPServerClientMacAddr

Column	Syntax	OID
filterDHCPServerIpAddr Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.7.2.1.1
filterDHCPServerClientMacAddr Ethernet Mac Address.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.10.75.14.14.7.2.1.2
filterDHCPServerPortList Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of p…	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.14.7.2.1.3
filterDHCPServerRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.7.2.1.4

A table to configure SSH user auth in the system.

sshUserInfoEntry row .1.3.6.1.4.1.171.10.75.14.14.8.12.1

An entry to configure user auth in the system.

Indexes

sshUserInfoID

Column	Syntax	OID
sshUserInfoID The Schedule identifier. The maximum number of Schedule entry is the number of ports supported PoE function. The value must be between 1 and 8.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.171.10.75.14.14.8.12.1.1
sshUserInfoUserName The ssh user name associated with the SSH suer Info. entry (e.g., `admin, user').	SNMPv2-TCDisplayString Constraints: range: 1-20 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.75.14.14.8.12.1.2
sshUserInfoAuth The object indicates which auth used by the user.	Enumerationr/w Enumerated Values: 1 hostbased 2 password 4 publickey	.1.3.6.1.4.1.171.10.75.14.14.8.12.1.3
sshUserInfoHostName The ssh host name associated with the SSH suer Info. entry (e.g., `DUT1, DUT2').	SNMPv2-TCDisplayStringr/w Constraints: range: 1-20 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.10.75.14.14.8.12.1.4
sshUserInfoHostIp SSH HostBased IP Address of the system.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.8.12.1.5

A Port-channel is created through ifMain table.
After the creation of the port-channel, corresponding logical
interface will be created in the ifMain table. 
This Port-channel table is indexed through Key values and allows to 
configure link selection policy and the Mac address for 
the port-channel. All other objects in this table displays 
the details of the port-channel

trafficSegEntry row .1.3.6.1.4.1.171.10.75.14.14.9.1.1

There is one entry in this table for each created
port-channel port

Indexes

trafficSegIfIndex

Column	Syntax	OID
trafficSegIfIndex The ifIndex of the port-channel(Aggregator's interface index).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.171.10.75.14.14.9.1.1.1
trafficSegMemberList Port list of port channel.	PortListr/w Description: Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents…	.1.3.6.1.4.1.171.10.75.14.14.9.1.1.2

A table that contains informations about server group.

aacServerGroupEntry row .1.3.6.1.4.1.171.10.75.14.14.10.5.1

A list of the group including servers.

Indexes

aacServerGroupIndex

Column	Syntax	OID
aacServerGroupIndex A value that uniquely identifies this SwAACServerGroupEntry .	Integer32 Constraints: range: 2-9	.1.3.6.1.4.1.171.10.75.14.14.10.5.1.1
aacServerGroupName A human-readable text string of the method group. The name is writable only if Group is new created, which the value of aacServerGroupRowStatus is 'notReady'.	OctetStringr/w Constraints: range: 1-15	.1.3.6.1.4.1.171.10.75.14.14.10.5.1.2
aacServersInGroup The list of servers in the group, each bit indicates a specified server ID. The server must be created before including it.	Bitsr/w Enumerated Values: 0 id-1 1 id-2 2 id-3 3 id-4 4 id-5 5 id-6 6 id-7 7 id-8 8 id-9 9 id-10 10 id-11 11 id-12 12 id-13 13 id-14 14 id-15 15 id-16	.1.3.6.1.4.1.171.10.75.14.14.10.5.1.3
aacServerGroupRowStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.10.5.1.4

A table that contains information about severs.

aacServerInfoEntry row .1.3.6.1.4.1.171.10.75.14.14.10.6.1

A list of the information of server .

Indexes

aacServerIndex

Column	Syntax	OID
aacServerIndex A value that uniquely identifies this SwAACServerGroupEntry.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.1
aacServerIPAddr The IP address of Server	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.2
aacServerAuthProtocol The authentication protocol provided by the Server.	Enumerationr/w Enumerated Values: 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.3
aacServerAuthPort The TCP/IP port .	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.4
aacServerAuthKey The key used while authentication process.	OctetStringr/w Constraints: range: 1-254	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.5
aacServerTimeout Server response timeout .	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.6
aacServerRetryCount The client retry count .	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.7
aacServerRowStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.10.6.1.8

A table that contains information about Login authentication method 
lists.

aacLoginMethodListEntry row .1.3.6.1.4.1.171.10.75.14.14.10.7.1

A list of the Authentication methods.

Indexes

aacLoginMethodListIndex

Column	Syntax	OID
aacLoginMethodListIndex A value that identifies this method list.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.1
aacLoginMethodListName A human-readable text string of the method list.	OctetStringr/w Constraints: range: 1-15	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.2
aacLoginMethod1 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.3
aacLoginMethod2 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.4
aacLoginMethod3 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.5
aacLoginMethod4 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.6
aacLoginMethodListRowStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.10.7.1.7

A table that contains information about Enable authentication method 
lists.

aacEnableMethodListEntry row .1.3.6.1.4.1.171.10.75.14.14.10.8.1

A list of the Authentication methods.

Indexes

aacEnableMethodListIndex

Column	Syntax	OID
aacEnableMethodListIndex A value that identifies this method list.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.1
aacEnableMethodListName A human-readable text string of the method list.	OctetStringr/w Constraints: range: 1-15	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.2
aacEnableMethod1 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.3
aacEnableMethod2 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.4
aacEnableMethod3 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.5
aacEnableMethod4 The type of Login method list. Besides the pre-defined type, it also allow to be set user-defined group by aacServerGroupIndex.	Enumerationr/w Enumerated Values: -1 none 0 local 1 tacacs-plus 2 radius	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.6
aacEnableMethodListRowStatus This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.10.75.14.14.10.8.1.7