DC-ISIS-MIB Table View

The set of instances of the Integrated IS-IS
protocol existing on the system.

isisSysEntry row .1.3.6.1.4.1.629.10.10.1.1.1.1

Each row defines information specific to a single
instance of the IS-IS protocol existing on the system.

Indexes

isisSysInstance

Column	Syntax	OID
isisSysInstance The unique identifier of the Integrated IS-IS instance to which this row corresponds. This object follows the index behavior.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.1
isisSysVersion The version number of the IS-IS protocol that is implemented.	Enumeration Enumerated Values: 0 unknown 1 one	.1.3.6.1.4.1.629.10.10.1.1.1.1.2
isisSysType At which levels is the Intermediate System running? This object follows the replaceOnlyWhileDisabled behavior.	Enumerationr/w Enumerated Values: 0 reserved 1 level1IS 2 level2IS 3 level1L2IS	.1.3.6.1.4.1.629.10.10.1.1.1.1.3
isisSysID The ID for this instance of the Integrated IS-IS protocol. This value is appended to each of the area addresses to form the Network Entity Titles. The derivation of a value for this object is implementation-specific. …	SystemIDr/w Type Constraints: range: 6	.1.3.6.1.4.1.629.10.10.1.1.1.1.4
isisSysMaxPathSplits Maximum number of paths with equal routing metric value which it is permitted to split between. Note that, when IGP shortcut interfaces are in use, this maximum applies individually to IGP shortcut paths …	Integer32r/w Constraints: range: 1-32	.1.3.6.1.4.1.629.10.10.1.1.1.1.5
isisSysMaxLSPGenInt Maximum interval, in seconds, between generated LSPs by this instance of the protocol. This object follows the resettingTimer behavior. The value must be greater than any value configured for isisSysLevelMinLSPGenInt, …	secondsInteger32r/w Constraints: range: 1-65235	.1.3.6.1.4.1.629.10.10.1.1.1.1.6
isisSysPollESHelloRate The value, in seconds, to be used for the suggested ES configuration timer in ISH PDUs when soliciting the ES configuration.	secondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.1.1.1.7
isisSysWaitTime Number of seconds to delay in waiting state before entering on state. This object follows the resettingTimer behavior.	secondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.1.1.1.8
isisSysAdminState The administrative state of this instance of the Integrated IS-IS protocol. Setting this object to the value 'on' when its current value is 'off' enables operation of this instance of the Integrated IS-IS protocol.	AdminStater/w Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.1.1.1.9
isisSysL2toL1Leaking If true, allow the router to leak L2 routes into L1.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.10
isisSysMaxAge Value to place in RemainingLifeTime field of the LSPs we generate. This should be at least 300 seconds greater than isisSysMaxLSPGenInt.	secondsUnsigned32r/w Constraints: range: 350-65535	.1.3.6.1.4.1.629.10.10.1.1.1.1.11
isisSysReceiveLSPBufferSize Size of the largest Buffer we are designed or configured to store. This should be at least as big as the maximum isisSysOrigLSPBuffSize supported by the system. If resources allow, we will store and floo…	bytesUnsigned32r/w Constraints: range: 1492-16000	.1.3.6.1.4.1.629.10.10.1.1.1.1.12
isisSysExistState The state of the IS-IS router. Turning this to state 'destroy' forces the router to forget all the current configuration. Setting the state to 'notInService' stops protocol processing, but retains the configuration.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.1.1.1.13
isisSysOperStatus The current operational status of this instance of the Protocol Manager component of DC-ISIS. Note that DC-ISIS can only activate if there is at least one active entry in the isisManAreaAddrTable.	IsisOperStatus Type Values: 1 operStatusUp 2 operStatusDown 3 operStatusGoingUp 4 operStatusGoingDown 5 operStatusActFailed	.1.3.6.1.4.1.629.10.10.1.1.1.1.14
isisSysAllowAutoI3Config If 'true' then add IP addresses received from the I3 stub to the isisCircIPAddrTable with admin state 'on'. If 'false' then add them with admin state 'off'. This field follows the replaceOnlyWhileDisabled behavior.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.15
isisSysCalcMaxDelay The maximum delay before the Routing Table is recalculated following a change to the Link State Database. (Recalculation is delayed to reduce the frequency of recalculations of the Routing Table). This p…	millisecondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.16
isisSysCalcThrshUpdStart This parameter can be used to override the routing calculation delay indicated by the isisSysCalcMaxDelay parameter when the number of updates to the Link State Database reaches a threshold value. This pa…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.17
isisSysCalcThrshUpdRestart This parameter can be used to interrupt a full routing calculation when the number of pending updates to the Link State Database has reached a threshold value. This parameter specifies the threshold numbe…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.18
isisSysCalcThrshRestartLimit This parameter limits the number of consecutive times a routing calculation can be interrupted by new updates. This guarantees that the routing calculation will actually complete. - 1 indicates that once …	Unsigned32r/w Constraints: range: 1-4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.19
isisSysCalcPauseFreq This value determines how regularly a Routing Calculation is paused. It is measured in points. The points scale roughly maps to a time scale, so that the larger this value is, the longer the Routing Calculation runs b…	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.20
isisSysCheckChecksums This value determines how often the checksums of LSPs in the Link State Database are checked. If 0, no checksums in the database are checked.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.21
isisSysZeroAgeLifetime This is the minimum amount of time in seconds for which the header of an expired LSP shall be retained after it has been flooded with zero Remaining Lifetime. All that is required is that the header be retained until t…	secondsSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.22
isisSysNumUpdPending The number of updates that are pending addition to the Link State Database.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.23
isisSysNumUpdMerged The number of updates that have been merged into the Link State Database since the last routing calculation.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.24
isisSysNumCksumsPending The number of LSPs in the Link State Database which are now due to have their checksum checked.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.25
isisSysTEMetricPcntge The Traffic Engineering metric is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal percentage change of the TE metric that causes a…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.26
isisSysMaxBwidthPcntge The maximum bandwidth on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal percentage change of maximum bandwidth th…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.27
isisSysMaxResBwidthPcntge The maximum reservable bandwidth on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal percentage change of maximum r…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.28
isisSysUnresBwidthPcntge The unreserved bandwidth on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal percentage change of unreserved bandwi…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.29
isisSysMaxLSPBwidthPcntge The maximum LSP bandwidth for the various switching descriptors on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.30
isisSysMinLSPBwidthPcntge The minimum LSP bandwidth for the various switching descriptors on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines the minimal…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.31
isisSysMTUSizePcntge The Maximum Transmission Unit size for the various switching descriptors on an interface is updated in real-time by the I3 Stub. In order to increase performance and reduce network traffic, this parameter determines th…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.32
isisSysTERouterID The Local IPv4 TE Router ID. This is a single stable IPv4 address that can always be referenced in a path that will be reachable from multiple hops away, regardless of the state of the node's interfaces. …	OctetStringr/w Constraints: range: 4-4 range: 0-0	.1.3.6.1.4.1.629.10.10.1.1.1.1.33
isisSysIPv6TERouterID The Local IPv6 TE Router ID. This is a single stable IPv6 global address that can always be referenced in a path that will be reachable from multiple hops away, regardless of the state of the node's interfaces. …	OctetStringr/w Constraints: range: 16-16 range: 0-0	.1.3.6.1.4.1.629.10.10.1.1.1.1.34
isisSysMaxExternalRoutes The maximum number of static routes and routes redistributed from other protocols that DC-ISIS will accept. The action that DC-ISIS will take when the maximum is exceeded is controlled by isisSysMaxExtern…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.1.1.35
isisSysMaxExternalRoutesAction The action that DC-ISIS will take when the number of external routes exceeds isisSysMaxExternalRoutes. If set to 'log', DC-ISIS will alert the administrator by logging that the limit has been exceeded. …	Enumerationr/w Enumerated Values: 1 log 2 suppressExternal	.1.3.6.1.4.1.629.10.10.1.1.1.1.36
isisSysLspFullSuppress The set of routes (if any) that will be removed from the local LSP by DC-ISIS when the local LSP becomes full at either level. When set to 'external', all static routes and routes redistributed from other…	Enumerationr/w Enumerated Values: 1 external 2 none	.1.3.6.1.4.1.629.10.10.1.1.1.1.37
isisSysLspFullSetDBOL If set to 'true', DC-ISIS will set the database overload flag in the local LSP (at all active levels) when the local LSP becomes full (at either level). The administrator can clear the database overload f…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.38
isisSysRestartHelpPeer Indicates whether DC-ISIS implements the procedures defined in the IS-IS restart RFC (3847) for helping a peer to restart. Note that this object has no effect on the local restart behavior, and so may be …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.39
isisSysRestartActivationType This object is only used when DC-ISIS is manually activated or deactivated (in other words, enters or leaves the state with row status 'active' and admin status 'on'), and indicates which restart procedures (if any) are…	IsisSysRestartTyper/w Type Values: 0 none 1 start 2 restart	.1.3.6.1.4.1.629.10.10.1.1.1.1.40
isisSysRestartAutoResetType There are cases where the IS-IS protocol requires the local node to automatically deactivate and later reactivate. This object indicates which restart procedures (if any) are followed during such an automatic reset. …	IsisSysRestartTyper/w Type Values: 0 none 1 start 2 restart	.1.3.6.1.4.1.629.10.10.1.1.1.1.41
isisSysRestartAdjacencyWait This object is only used when DC-ISIS activates with the activation type (isisSysRestartActivationType or isisSysRestartAutoResetType) set to 'start' or 'restart'. It defines how long DC-ISIS will wait to…	secondsInteger32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.629.10.10.1.1.1.1.42
isisSysMaxRecoveryTime This object is only used when DC-ISIS activates with the activation type (isisSysRestartActivationType or isisSysRestartAutoResetType) set to 'restart'. It defines the maximum time that DC-ISIS will take …	secondsInteger32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.1.1.1.43
isisSysClearStats Set to 'true' to clear all system statistics, including the isisSystemCounter and isisPacketCounter tables. Note that isisSysStatsLSPCount is not reset by this object. Reading the value of …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.44
isisSysSetAttached If DC-ISIS is operating at both level 1 and level 2, this field indicates how DC-ISIS should decide whether to set the attached bit in its level 1 LSP. - 'attachNoOverlapOrRedist' indicates that the atta…	Enumerationr/w Enumerated Values: 1 attachNoOverlapOrRedist 2 attachNoOverlapOnly 3 attachSet 4 attachClear	.1.3.6.1.4.1.629.10.10.1.1.1.1.45
isisSysProtSupported This attribute contains the set of protocols supported by this Intermediate System.	IsisAddrTypeBitsr/w Type Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.629.10.10.1.1.1.1.46
isisSysRestrictLanAdjsToSubnet This object only affects IPv4 broadcast circuits. If this is set to 'true', DC-ISIS will only form adjacencies with intermediate systems that are on the same subnet as the local circuit. This object only has effect wh…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.47
isisSysHostName The string that this instance of IS-IS will use as the local hostname. This is advertised to other Intermediate Systems in the Dynamic Hostname TLV.	SNMP-FRAMEWORK-MIBSnmpAdminStringr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.1.1.1.48
isisSysCalcSoonAfterCircChange Set this object to 'true' to minimize the delay before triggering a routing calculation that includes any relevant circuit change. This means a change to the local neighbors (including pseudonodes), or to the reachable…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.49
isisSysSendNotifications This attribute contains the set of notifications generated by this Intermediate System. The notifications that may be enabled are the isisCircIndTable, isisDatabaseOverload, isisManualAddressDrops, isisID…	Bitsr/w Enumerated Values: 0 circuitIndication 1 databaseOverload 2 manualAreaAddressDrops 3 idLengthMismatch 4 maxAreaAddressMismatch 5 ownLspPurge 6 areaMismatch 7 rejectedAdjacency 8 adjacencyChange 9 lspErrorDetected 10 attemptToExceedMaxSequence 11 sequenceNumberSkip 12 extPassCircuitInd 13 operStateChange 14 disChange 15 lspAuthFailure 16 helloAuthFailure 17 attachStateChange	.1.3.6.1.4.1.629.10.10.1.1.1.1.50
isisSysEnableIgpShortcut Set isisSysEnableIgpShortcut to 'true' to enable IS-IS routing over IGP shortcut interfaces. Set isisSysEnableIgpShortcut to 'false' to disable IS-IS routing over IGP shortcut interfaces. IS-IS will igno…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.1.1.51
isisSysI3EntityIndex Identifies the I3 stub instance to which this IS-IS instance should join. The status of the join is given by the row in the isisPmMjTable with isisPmMjInterface equal to ifInterfaceInfo. No…	DC-MASTER-TCNumericIndexr/w Type Constraints: range: 1..2147483647	.1.3.6.1.4.1.629.10.10.1.1.1.1.52
isisSysRtmPurgeTime This object defines the maximum time that DC-ISIS will wait when a Routing Table Manager (such as DC-RTM) fails before purging routes. In some systems, the Routing Table Manager may restart independently …	secondsInteger32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.629.10.10.1.1.1.1.53

The set of manual area addresses configured on this
Intermediate System.

isisManAreaAddrEntry row .1.3.6.1.4.1.629.10.10.1.1.2.1

Each entry contains one area address manually configured
on this system

Indexes

isisSysInstance isisManAreaAddr

Column	Syntax	OID
isisManAreaAddr A manually configured area address for this system. This object follows the index behavior. Note: an index for the entry {1, {49.0001} active} in this table would be the ordered pair (1, (0x03 0x49 0x00 0…	OSINSAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.629.10.10.1.1.2.1.1
isisManAreaAddrExistState The state of the isisManAreaAddrEntry. This object follows the Row Status behavior. If the isisSysAdminState for this instance of the IS-IS protocol is 'on', and an attempt is made to set this object to the value 'destr…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.1.2.1.2

The union of the sets of area addresses reported in all
Level 1 LSPs with segment number zero received by this
instance of the protocol from Intermediate Systems which
are reachable via Level 1 routing.

isisAreaAddrEntry row .1.3.6.1.4.1.629.10.10.1.1.3.1

Each entry contains one area address reported in a
Level 1 LSP received by this instance of the IS-IS
protocol.

The DC-ISIS implementation ignores received area addresses
with a length of zero.

Indexes

isisSysInstance isisAreaAddr

Column	Syntax	OID
isisAreaAddr An area address reported in a Level 1 LSP received by this instance of the IS-IS protocol. The DC-ISIS implementation ignores received area addresses with a length of zero.	OSINSAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.629.10.10.1.1.3.1.1
isisAreaAddrInLSP Following ISO10589 section 7.1.5, we advertise the three numerically lowest level 1 area addresses in the level 2 LSP fragment zero. If 'true', then this area address is one of the three numerically lowes…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.3.1.2

The set of IP summary addresses to use in forming
summary TLVs originated by this Intermediate System.
          
An administrator may use a summary address to combine
and modify IP Reachability announcements.  If the
Intermediate system can reach any subset of the summary
address, the summary address will be announced instead,
at the configured metric.

isisSummAddrEntry row .1.3.6.1.4.1.629.10.10.1.1.5.1

Each entry contains one IP summary address.

Indexes

isisSysInstance isisSummAddrMtId isisSummAddressType isisSummAddress isisSummAddrPrefixLen

Column	Syntax	OID
isisSummAddressType The Type of IP address for this summary address. This object follows the index behavior.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.1.5.1.1
isisSummAddress The IP Address value for this summary address. This object follows the index behavior. The address must not contain any set host bits (bits set after the address prefix determined by isisSummAddrPrefixLen…	OctetString Constraints: range: 4-4 range: 16-16	.1.3.6.1.4.1.629.10.10.1.1.5.1.2
isisSummAddrPrefixLen The Length of the IP NetMask for this summary address.	Unsigned32 Constraints: range: 0-128	.1.3.6.1.4.1.629.10.10.1.1.5.1.3
isisSummAddrExistState The existence state of this summary address. This object follows the row status behavior.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.1.5.1.4
isisSummAddrMetric The metric value to announce this summary address with in LSPs generated by this system.	Integer32r/w Constraints: range: 1-63	.1.3.6.1.4.1.629.10.10.1.1.5.1.5
isisSummAddrFullMetric The wide metric value to announce this summary address with in LSPs generated by this system.	FullMetricr/w	.1.3.6.1.4.1.629.10.10.1.1.5.1.6
isisSummAddrMtId The topology that this summary address applies to. This should be set to zero if multi-topology IS-IS is not enabled. This object follows the index behavior.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.1.5.1.8

This table provides criteria to decide if a route should
be leaked from L2 to L1 when Domain Wide Prefix leaking is
enabled.
          
Addresses that match the summary mask in the table will
be announced at L1 by routers when isisSysL2toL1Leaking
is enabled.  Routes that fall into the ranges specified
are announced as is, without being summarized.  Routes
that do not match a summary mask are not announced.

isisRedistributeAddrEntry row .1.3.6.1.4.1.629.10.10.1.1.6.1

Each entry contains one IP summary address to
manage leaking L2 addresses into L1.

Indexes

isisSysInstance isisRedistributeAddrMtId isisRedistributeAddrType isisRedistributeAddrAddress isisRedistributeAddrPrefixLen

Column	Syntax	OID
isisRedistributeAddrType The Type of IP address for this summary address. This object follows the index behavior.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.1.6.1.1
isisRedistributeAddrAddress The IP Address value for this summary address. This object follows the index behavior. The address must not contain any set host bits (bits set after the address prefix determined by isisRedistributeAddrP…	OctetString Constraints: range: 16-16 range: 4-4	.1.3.6.1.4.1.629.10.10.1.1.6.1.2
isisRedistributeAddrPrefixLen The Length of the IP NetMask for this summary address.	Unsigned32 Constraints: range: 0-128	.1.3.6.1.4.1.629.10.10.1.1.6.1.3
isisRedistributeAddrExistState The existence state of this summary address. This object follows the row status behavior.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.1.6.1.4
isisRedistributeAddrMtId The topology that this redistribution address applies to. This should be set to zero if multi-topology IS-IS is not enabled. This object follows the index behavior.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.1.6.1.6

The set of hostnames and router ID.

isisRouterEntry row .1.3.6.1.4.1.629.10.10.1.1.7.1

Each entry tracks information about one peer at
one level.

Indexes

isisSysInstance isisRouterSysID isisRouterLevel

Column	Syntax	OID
isisRouterSysID The System ID of the Router Peer.	SystemID Type Constraints: range: 6	.1.3.6.1.4.1.629.10.10.1.1.7.1.1
isisRouterLevel The level of this Intermediate System.	ISLevel Type Values: 0 none 1 area 2 domain	.1.3.6.1.4.1.629.10.10.1.1.7.1.2
isisRouterHostName The hostname listed in LSP, or NULL if none.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.1.7.1.3
isisRouterID The Router ID of the Peer found in LSP, or NULL if none.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.1.7.1.4
isisRouterIPv6ID The IPv6 TE Router ID found in the LSP, if any.	INET-ADDRESS-MIBInetAddressIPv6 Type Constraints: range: 16	.1.3.6.1.4.1.629.10.10.1.1.7.1.5

A row in this table represents the level of support for a
topology on this instance of the Integrated IS-IS protocol.
          
This table is only used when multi-topology IS-IS is
supported.

isisMtSysEntry row .1.3.6.1.4.1.629.10.10.1.1.8.1

Each row defines information specific to a single topology on a
single instance of the IS-IS protocol existing on the system.

Indexes

isisSysInstance isisMtSysMtId

Column	Syntax	OID
isisMtSysMtId The topology that this row represents.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.1.8.1.2
isisMtSysExistState The state of the MIB row. Turning this to state 'destroy' forces the router to forget all the current topology configuration. Setting the state to 'notInService' stops protocol processing for this topology, but retain…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.1.8.1.3
isisMtSysAdminState The desired operational state of this topology on this instance of the Integrated IS-IS protocol. Setting this object to the value 'on' when its current value is 'off' enables operation of this topology for this instan…	AdminStater/w Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.1.8.1.4
isisMtSysOperState The current operational status of this topology on this instance of the Integrated IS-IS protocol. If this is 'down' then the topology is not supported.	IsisOperStatus Type Values: 1 operStatusUp 2 operStatusDown 3 operStatusGoingUp 4 operStatusGoingDown 5 operStatusActFailed	.1.3.6.1.4.1.629.10.10.1.1.8.1.5
isisMtSysProtSupported This attribute contains the set of protocols supported by this topology on this Intermediate System. Note that RFC 5120 assigns certain topologies to serve pre-determined purposes (MT IDs 0 - 5). This li…	IsisAddrTypeBitsr/w Type Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.629.10.10.1.1.8.1.6
isisMtSysDefaultActive When set to 'true', corresponding rows in the isisMtCircStatusTable have oper status 'up', unless a corresponding row exists in the isisMtCircManConfigTable. When set to 'false', corresponding rows in the…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.1.8.1.7

Level specific information about an instance of IS-IS.

isisSysLevelEntry row .1.3.6.1.4.1.629.10.10.1.2.1.1

Describe variables defined for Area or Domain.

Indexes

isisSysInstance isisSysLevelIndex

Column	Syntax	OID
isisSysLevelIndex The level that this entry describes.	Enumeration Enumerated Values: 0 none 1 level1IS 2 level2IS	.1.3.6.1.4.1.629.10.10.1.2.1.1.1
isisSysLevelOrigLSPBuffSize The maximum size of LSPs and SNPs originated by this Intermediate System at this level. This object follows the replaceOnlyWhileDisabled behavior.	LSPBuffSizer/w Type Constraints: range: 512..16000	.1.3.6.1.4.1.629.10.10.1.2.1.1.2
isisSysLevelMinLSPGenInt Minimum interval, in milliseconds, between successive generation of LSPs with the same LSPID at this level by this instance of the protocol. This object follows the resettingTimer behavior.	millisecondsUnsigned32r/w Constraints: range: 1-65535000	.1.3.6.1.4.1.629.10.10.1.2.1.1.3
isisSysLevelOverloadState The Overload state of the database at this level. The value 'overloaded' indicates a database that is low on an essential resource, such as memory. The administrator may indirectly force the state to 'waiting' when the …	LevelState Type Values: 1 off 2 on 3 waiting 4 overloaded	.1.3.6.1.4.1.629.10.10.1.2.1.1.4
isisSysLevelSetOverload Administratively set the overload bit for the level. The overload bit will continue to be set if the implementation runs out of memory, independent of this variable.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.2.1.1.5
isisSysLevelSetOverloadUntil If set, the overload bit should be set, and cleared after sysUpTime exceeds this value.	secondsSNMPv2-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.2.1.1.6
isisSysLevelMetricStyle Which style of Metric do we generate in our LSPs at this level?	MetricStyler/w Type Values: 1 narrow 2 wide 3 both	.1.3.6.1.4.1.629.10.10.1.2.1.1.7
isisSysLevelSPFConsiders Which style of Metric do we consider in our SPF computation at this level?	MetricStyler/w Type Values: 1 narrow 2 wide 3 both	.1.3.6.1.4.1.629.10.10.1.2.1.1.8
isisSysLevelTEEnabled Do we do Traffic Engineering for IPv4 at this level? If Traffic Engineering is enabled, isisSysLevelMetricStyle must be set to 'wide' or 'both' for this level, and a value must be configured for isisSysTE…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.2.1.1.9
isisSysLevelIPv6TEEnabled Do we do Traffic Engineering for IPv6 at this level? DC-ISIS only supports Traffic Engineering for IPv6 at level 1. If Traffic Engineering is enabled, a value must be configured for isisSys…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.2.1.1.10
isisSysLevelRestartT2Duration This object is only used when DC-ISIS activates with the activation type (isisSysRestartActivationType or isisSysRestartAutoResetType) set to 'start' or 'restart'. It defines how long DC-ISIS will wait to…	secondsInteger32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.629.10.10.1.2.1.1.11
isisSysLevelAuthUser Authentication user data for area/domain level authentication. This data is passed opaquely to the Metaswitch authentication interface where it can be used to assist with authentication decisions.	DC-MASTER-TCAuthUserDataStringr/w Type Constraints: range: 0..22	.1.3.6.1.4.1.629.10.10.1.2.1.1.12

The table of circuits used by each instance of
Integrated IS-IS on this system.

isisCircEntry row .1.3.6.1.4.1.629.10.10.1.3.2.1

An isisCircEntry exists for each circuit used by
Integrated IS-IS on this system.

Indexes

isisSysInstance isisCircIndex

Column	Syntax	OID
isisCircIndex The identifier of this circuit, unique within the instance of the IS-IS protocol. This object follows the index behavior. This is for SNMP Indexing purposes only and need not have any relation to any protocol value. …	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.629.10.10.1.3.2.1.1
isisCircIfIndex The value of ifIndex for the interface to which this circuit corresponds. This object cannot be modified after creation. In DC-ISIS this is also used as the 3-way circuit ID on point-to-point circuits, …	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.629.10.10.1.3.2.1.2
isisCircIfSubIndex A specifier for the part of the interface ifIndex to which this circuit corresponds, such as a DLCI or VPI/VCI. This object cannot be modified after creation. In DC-ISIS this field is ignored.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.629.10.10.1.3.2.1.3
isisCircAdminState The administrative state of the circuit. This object follows the AdminState behavior. In DC-ISIS the default admin state for a new automatic circuit is 'on' if the isisSysAllowAutoI3Config field is 'true'…	AdminStater/w Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.3.2.1.4
isisCircExistState The existence state of this circuit. This object follows the Row Status behavior. Setting the state to 'notInService' halts the generation and processing of IS-IS protocol PDUs on this circuit. Setting the state to de…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.3.2.1.5
isisCircType The type of the circuit. This object follows the replaceOnlyWhileDisabled behavior. The type specified must be compatible with the type of the interface defined by the value of isisCircIfIndex. In DC-ISIS…	Enumerationr/w Enumerated Values: 0 unknown 1 broadcast 2 ptToPt 3 staticIn 4 staticOut 5 dA	.1.3.6.1.4.1.629.10.10.1.3.2.1.6
isisCircExtDomain If true, suppress normal transmission of and interpretation of Intra-domain IS-IS PDUs on this circuit.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.7
isisCircLevel Indicates which type of packets will be sent and accepted on this circuit. The values used will be modified by the settings of isisSysType. This object follows the replaceOnlyWhileDisabled behavior.	Enumerationr/w Enumerated Values: 0 reserved 1 level1 2 level2 3 level1L2	.1.3.6.1.4.1.629.10.10.1.3.2.1.8
isisCircPassiveCircuit Should we include this interface in LSPs, even if it is not running the IS-IS Protocol? In DC-ISIS, circuits with isisCircExtDomain 'true' will only be included in LSPs if this field is also 'true', and t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.9
isisCircMeshGroupEnabled Is this port a member of a mesh group, or blocked? Circuits in the same mesh group act as a virtual multiaccess network. LSPs seen on one circuit in a mesh group will not be flooded to another circuit in the same mesh …	Enumerationr/w Enumerated Values: 1 inactive 2 blocked 3 set	.1.3.6.1.4.1.629.10.10.1.3.2.1.10
isisCircMeshGroup Circuits in the same mesh group act as a virtual multiaccess network. LSPs seen on one circuit in a mesh group will not be flooded to another circuit in the same mesh group. If isisCircMeshGroupEnabled is inactive or …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.11
isisCircSmallHellos Can we send unpadded hellos on LAN circuits? False means LAN Hellos must be padded. Implementations should allow the administrator to read this value. An implementation need not be able to support unpadded hellos to b…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.12
isisCircLastUpTime If the circuit is enabled, the value of sysUpTime when isisCircAdminState most recently entered the state on. If the circuit is not on, the value of sysUpTime when the circuit last entered state on, 0 if the circuit ha…	secondsSNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.13
isisCirc3WayEnabled Is this circuit enabled to run 3Way handshake? DC-ISIS will always run the 3-way handshake on point to point circuits, and so this object is read-only.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.14
isisCircExtendedCircID The value to be used as the extended circuit ID in 3Way handshake. This value is only used if isisCirc3WayEnabled is true, and must be unique across all circuits on this IS. DC-ISIS uses the value for is…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.15
isisCircOperState The operational state of this circuit.	IsisOperStatus Type Values: 1 operStatusUp 2 operStatusDown 3 operStatusGoingUp 4 operStatusGoingDown 5 operStatusActFailed	.1.3.6.1.4.1.629.10.10.1.3.2.1.16
isisCircSdEntityIndex Identifies the SDC entity which will handle this circuit. This object must be specified before the circuit can run the IS-IS protocol. It cannot be changed after it has been specified.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.629.10.10.1.3.2.1.17
isisCircDlBuffPoolSize Capacity of the buffer pool used by the DL stub to send data signals to the SDC. This object follows the replaceOnlyWhileDisabled behavior.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.18
isisCircSdPDUBuffPoolSize Capacity of the buffer pool into which SDC transfers data signals from the DL Stub. This object follows the replaceOnlyWhileDisabled behavior.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.19
isisCircSdIndBuffPoolSize Capacity of the buffer pool used by SDC to send indications to PM. This object follows the replaceOnlyWhileDisabled behavior.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.20
isisCircDataLinkBlockSize Maximum size of PDU that can be sent or received over this circuit (MTU). This object follows the replaceOnlyWhileDisabled behavior.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.3.2.1.21
isisCircPhysicalAddress The physical address of the network interface (for example a MAC address on an Ethernet card). This value is only relevant to a broadcast circuit and is ignored on a point-to-point circuit. It needs to be specified in…	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.629.10.10.1.3.2.1.22
isisCircManualOrAutomatic Has this circuit been configured by MIB (manual), I3 information (automatic) or both? MIB configuration overrides I3 configuration. Automatic circuits cannot be destroyed. Destroying a manual circuit re…	Enumeration Enumerated Values: 1 manual 2 automatic 3 both	.1.3.6.1.4.1.629.10.10.1.3.2.1.23
isisCircT1TimerRunning Is the T1 timer running on this circuit? This object is only valid on a circuit that is currently running the IS-IS protocol (isisCircExtDomain is 'false' and isisCircOperState is 'operStatusUp'). …	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.24
isisCircProtSupported Which protocols are supported on this circuit? Note that the configured value is used in conjunction with the value of isisSysProtSupported. In particular: - IPv4 is supported on the circ…	IsisAddrTypeBitsr/w Type Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.629.10.10.1.3.2.1.25
isisCircPtToPtOverLAN Allows a broadcast circuit to be configured to operate point-to-point over LAN procedures. This is used in conjunction with the isisCircType object as follows. - If isisCircType = 'ptToPt'…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.2.1.26
isisCircProtBfdDesired Indicates the protocols running on this circuit for which Bidirectional Forwarding Detection (BFD) is desired. If isisCircProtBfdDesired is clear for an address type, then BFD sessions are not established…	IsisAddrTypeBitsr/w Type Values: 1 ipv4 2 ipv6	.1.3.6.1.4.1.629.10.10.1.3.2.1.28
isisCircIfName The textual name of the interface. The value of this object should be the name of the interface as assigned by the local device and should be suitable for use in commands entered at the device's 'console'. This might …	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.629.10.10.1.3.2.1.29

This table contains the set of IP Addresses configured on
all circuits.

isisCircIPAddrEntry row .1.3.6.1.4.1.629.10.10.1.3.3.1

Each entry contains one IP Address configured on a
circuit.

Indexes

isisSysInstance isisCircIndex isisCircIPAddrManOrAuto isisCircIPAddrIndex

Column	Syntax	OID
isisCircIPAddrManOrAuto The type of IP address. Those of type manual are created by the network manager. Those of type automatic are created through propagation of interface information from the I3 stub. This object cannot be modified after …	Enumeration Enumerated Values: 1 manual 2 automatic 3 both	.1.3.6.1.4.1.629.10.10.1.3.3.1.1
isisCircIPAddrIndex An index to this table which identifies the IP addresss to which this entry belongs. This object follows the manualOrAutomatic behavior.	Integer32 Constraints: range: 1-2000000000	.1.3.6.1.4.1.629.10.10.1.3.3.1.2
isisCircIPAddrRowStatus The existence state of this IP address. This object follows the RowStatus and manualOrAutomatic behaviors.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.3.3.1.3
isisCircIPAddrAdminState Administrative state of this IP address. This object follows the AdminState and manualOrAutomatic behaviors. The system level isisSysAllowAutoI3Config field defines the initial administrative state for I…	AdminStater/w Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.3.3.1.4
isisCircIPAddrAddressType The Inet type of this IP Address. This object follows the manualOrAutomatic behavior.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.3.3.1.5
isisCircIPAddrAddress One IP Address configured on this circuit. This field must be present on row creation and cannot be modified after creation. This address must be unique among all manual IP addresses configured on this c…	OctetStringr/w Constraints: range: 16-16 range: 4-4	.1.3.6.1.4.1.629.10.10.1.3.3.1.6
isisCircIPAddrInLSP Is this IP address advertised in TLV 132 in LSPs sent out by this intermediate system? This object follows the manualOrAutomatic behavior.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.3.3.1.7

A row in this table represents the manual configuration of
support for a topology on this circuit.
          
Rows in this table are created and destroyed by an
administrator to provide per-circuit multi-topology
configuration.
          
Note that the presence of a row in this table overrides the
default multi-topology settings for the given circuit and
topology.

isisMtCircManConfigEntry row .1.3.6.1.4.1.629.10.10.1.3.4.1

An isisMtCircManConfigEntry is created to provide
multi-topology specifc circuit configuration.

Indexes

isisSysInstance isisCircIndex isisMtCircManMtId

Column	Syntax	OID
isisMtCircManMtId The topology that this row represents.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.3.4.1.3
isisMtCircManExistState The state of the MIB row. Turning this to state 'destroy' forces the router to forget the manually configured multi-topology configuration for this circuit. Setting the state to 'notInService' stops the manual multi-t…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.3.4.1.4
isisMtCircManAdminState The desired operational state for the manual configuration of this topology on this circuit. Setting this object to the value 'on' when its current value is 'off' enables use of the manual configuration for this topolo…	AdminStater/w Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.3.4.1.5
isisMtCircManOperState The current operational status of the manual configuration for this topology on this circuit.	IsisOperStatus Type Values: 1 operStatusUp 2 operStatusDown 3 operStatusGoingUp 4 operStatusGoingDown 5 operStatusActFailed	.1.3.6.1.4.1.629.10.10.1.3.4.1.6
isisMtCircManL1WideMetric The level 1 wide metric value of this circuit for this topology. Note that topologies other than MT ID 0 always use wide metrics. For multi-topology ID zero (the base topology), this field is read only. …	WideMetricr/w Type Constraints: range: 1..16777215	.1.3.6.1.4.1.629.10.10.1.3.4.1.7
isisMtCircManL2WideMetric The level 2 wide metric value of this circuit for this topology. Note that topologies other than MT ID 0 always use wide metrics. For multi-topology ID zero (the base topology), this field is read only. …	WideMetricr/w Type Constraints: range: 1..16777215	.1.3.6.1.4.1.629.10.10.1.3.4.1.8

A row in this table represents the current support for a
topology on this circuit.
          
A row exists in this table for every row in the
isisCircTable and every row in the isisMtSysTable.

isisMtCircStatusEntry row .1.3.6.1.4.1.629.10.10.1.3.5.1

An isisMtCircStatusEntry details the status of a topology
on a circuit.

Indexes

isisSysInstance isisCircIndex isisMtCircStatusMtId

Column	Syntax	OID
isisMtCircStatusMtId The topology that this row represents.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.3.5.1.3
isisMtCircStatusOperState The current operational state of this topology on this circuit. If no corresponding row exists in the isisMtCircManConfigTable then this is derived from the isisMtSysDefaultActive field in the isisMtSysTa…	IsisOperStatus Type Values: 1 operStatusUp 2 operStatusDown 3 operStatusGoingUp 4 operStatusGoingDown 5 operStatusActFailed	.1.3.6.1.4.1.629.10.10.1.3.5.1.4
isisMtCircStatusL1WideMetric The level 1 wide metric value of this circuit for this topology. Note that topologies other than MT ID 0 always use wide metrics. If no corresponding row exists in the isisMtCircManConfigTable then this …	WideMetric Type Constraints: range: 1..16777215	.1.3.6.1.4.1.629.10.10.1.3.5.1.5
isisMtCircStatusL2WideMetric The level 2 wide metric value of this circuit for this topology. Note that topologies other than MT ID 0 always use wide metrics. If no corresponding row exists in the isisMtCircManConfigTable then this …	WideMetric Type Constraints: range: 1..16777215	.1.3.6.1.4.1.629.10.10.1.3.5.1.6

Level specific information about circuits used by IS-IS.

isisCircLevelEntry row .1.3.6.1.4.1.629.10.10.1.4.1.1

An isisCircLevelEntry exists for each level on
each circuit used by Integrated IS-IS on this system.

Indexes

isisSysInstance isisCircIndex isisCircLevelIndex

Column	Syntax	OID
isisCircLevelIndex The level that this entry describes.	Enumeration Enumerated Values: 0 none 1 level1IS 2 level2IS	.1.3.6.1.4.1.629.10.10.1.4.1.1.1
isisCircLevelMetric The metric value of this circuit for this level.	Integer32r/w Constraints: range: 1-63	.1.3.6.1.4.1.629.10.10.1.4.1.1.2
isisCircLevelWideMetric The wide metric value of this circuit for this level.	WideMetricr/w Type Constraints: range: 1..16777215	.1.3.6.1.4.1.629.10.10.1.4.1.1.3
isisCircLevelISPriority The priority for becoming LAN Designated Intermediate System at this level.	ISPriorityr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.629.10.10.1.4.1.1.4
isisCircLevelIDOctet A one byte identifier for the circuit selected by the Intermediate System. On point-to-point circuits, the value is used as the Local Circuit ID in point-to-point IIH PDUs transmitted on this circuit. In…	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.629.10.10.1.4.1.1.5
isisCircLevelID On a point to point circuit with a fully initialized adjacency to a peer IS, the value of this object is the circuit ID negotiated during adjacency initialization. On a point to point circuit without such an adjacency, …	CircuitID Type Constraints: range: 0 range: 7	.1.3.6.1.4.1.629.10.10.1.4.1.1.6
isisCircLevelDesIS The ID of the LAN Designated Intermediate System on this circuit at this level. If, for any reason, this system is not partaking in the relevant Designated Intermediate System election process, then the value returned i…	CircuitID Type Constraints: range: 0 range: 7	.1.3.6.1.4.1.629.10.10.1.4.1.1.7
isisCircLevelHelloMultiplier This value is multiplied by the corresponding HelloTimer and the result in seconds (rounded up) is used as the holding time in transmitted hellos, to be used by receivers of hello packets from this IS.	Integer32r/w Constraints: range: 2-100	.1.3.6.1.4.1.629.10.10.1.4.1.1.8
isisCircLevelHelloTimer Maximum period, in milliseconds, between IIH PDUs on multiaccess networks at this level for LANs. The value at L1 is used as the period between Hellos on L1L2 point to point circuits. Setting this value at level 2 on a…	millisecondsInteger32r/w Constraints: range: 10-600000	.1.3.6.1.4.1.629.10.10.1.4.1.1.9
isisCircLevelDRHelloTimer Period, in milliseconds, between Hello PDUs on multiaccess networks when this IS is the Designated Intermediate System. This object follows the resettingTimer behavior.	millisecondsInteger32r/w Constraints: range: 10-120000	.1.3.6.1.4.1.629.10.10.1.4.1.1.10
isisCircLevelLSPThrottle Minimal interval of time, in milliseconds, between transmissions of LSPs on an interface at this level.	millisecondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.4.1.1.11
isisCircLevelMinLSPRetransInt Minimum interval, in milliseconds, between re-transmission of an LSP at this level. This object follows the resettingTimer behavior. Note that isisCircLevelLSPThrottle controls how fast we send back to ba…	millisecondsInteger32r/w Constraints: range: 1-300000	.1.3.6.1.4.1.629.10.10.1.4.1.1.12
isisCircLevelCSNPInterval Interval of time, in seconds, between periodic transmission of a complete set of CSNPs on multiaccess networks if this router is the designated router at this level. This object follows the resettingTimer behavior.	secondsInteger32r/w Constraints: range: 1-600	.1.3.6.1.4.1.629.10.10.1.4.1.1.13
isisCircLevelPartSNPInterval Minimum interval in seconds between sending Partial Sequence Number PDUs at this level. This object follows the resettingTimer behavior.	secondsInteger32r/w Constraints: range: 1-120	.1.3.6.1.4.1.629.10.10.1.4.1.1.14
isisCircLevelStickyDIS Boost to add to the priority of this router (up to the maximum permitted value) when it becomes DIS at this level to make it more likely to remain DIS.	Integer32r/w Constraints: range: 0-127	.1.3.6.1.4.1.629.10.10.1.4.1.1.15
isisCircLevelAuthUser Authentication user data for this level's authentication. This data is passed opaquely to the Metaswitch authentication interface where it can be used to assist with authentication decisions.	DC-MASTER-TCAuthUserDataStringr/w Type Constraints: range: 0..22	.1.3.6.1.4.1.629.10.10.1.4.1.1.16
isisCircLevelIDHostname The hostname corresponding to the system ID part of the isisCircLevelID object. This is the null string if the isisCircLevelID object is null, or if no hostname is known.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.4.1.1.17
isisCircLevelDesISHostname The hostname corresponding to the system ID part of the isisCircLevelDesIS object. This is the null string if the isisCircLevelDesIS object is null, or if no hostname is known.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.4.1.1.18
isisCircLevelMinLSPArrivalInt The minimum interval between reception of new instances of a particular LSP. LSP instances received at higher frequencies are discarded. If set to zero then no check is made on the frequency of LSP reception. …	millisecondsInteger32r/w Constraints: range: 0-60000	.1.3.6.1.4.1.629.10.10.1.4.1.1.19

System wide counters for one instance of the IS-IS
protocol on the system.

isisSystemCounterEntry row .1.3.6.1.4.1.629.10.10.1.5.1.1

System-wide IS-IS counters.

Indexes

isisSysInstance isisSysStatLevel

Column	Syntax	OID
isisSysStatLevel The level that this entry describes.	Enumeration Enumerated Values: 0 none 1 level1IS 2 level2IS	.1.3.6.1.4.1.629.10.10.1.5.1.1.1
isisSysStatCorrLSPs Number of corrupted in-memory LSPs detected. LSPs received from the wire with a bad checksum are silently dropped and not counted. LSPs received from the wire with parse errors are counted …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.2
isisSysStatAuthTypeFails The number of authentication type mismatches recognized by this instance of the protocol.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.3
isisSysStatAuthFails The number of authentication failures recognized by this instance of the protocol.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.4
isisSysStatLSPDbaseOloads Number of times the LSP database has become overloaded.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.5
isisSysStatManAddrDropFromAreas Number of times a manual address has been dropped from the area.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.6
isisSysStatAttmptToExMaxSeqNums Number of times the IS has attempted to exceed the maximum sequence number.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.7
isisSysStatSeqNumSkips Number of times a sequence number skip has occurred.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.8
isisSysStatOwnLSPPurges Number of times a zero-aged copy of the system's own LSP is received from some other node.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.9
isisSysStatIDFieldLenMismatches Number of times a PDU is received with a different value for ID field length to that of the receiving system.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.10
isisSysStatPartChanges Partition changes.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.11
isisSysStatSPFRuns Number of times we ran SPF at this level.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.12
isisSysStatLSPError The count of badly formed LSPs discarded by the PM component of DC-ISIS.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.13
isisSysStatCSNPError The count of badly formed CSNPs discarded by the PM component of DC-ISIS.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.14
isisSysStatPSNPError The count of badly formed PSNPs discarded by the PM component of DC-ISIS.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.15
isisSysStatLSPQueueLen The count of received LSPs that are queued internally in the PM component of DC-ISIS, awaiting processing.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.16
isisSysStatFragsRebuilt Number of LSP fragments that the local system has generated.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.17
isisSysStatLSPRexmits Number of LSPs that have been retransmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.18
isisSysStatLSPRegens Number of LSPs that have been regenerated. An LSP is regenerated when it is nearing the end of its lifetime and it has not changed.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.19
isisSysStatPurgesInitiated Number of LSP purges that have been initiated by this instance of IS-IS.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.20
isisSysStatLSPCount The number of LSPs in the database at this level.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.21
isisSysStatPurgesIniLocal Number of LSP purges initiated by this instance of IS-IS, of LSPs that were originated locally. This field behaves like an SNMP counter. It only increases, never decreases, and is subject to wrap. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.23
isisSysStatPurgesIniRemote Number of LSP purges initiated by this instance of IS-IS, of LSPs that were originated remotely. This field behaves like an SNMP counter. It only increases, never decreases, and is subject to wrap. …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.24
isisSysStatPurgesIniRemSNP Number of LSP purges initiated by this instance of IS-IS, of LSPs that were originated remotely, due to receiving a SNP. This field behaves like an SNMP counter. It only increases, never decreases, and i…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.25
isisSysStatPurgesIniRemExp Number of LSP purges initiated by this instance of IS-IS, of LSPs that were originated remotely, because they have expired. This field behaves like an SNMP counter. It only increases, never decreases, an…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.26
isisSysStatPurgesIniRemPrs Number of LSP purges initiated by this instance of IS-IS, of LSPs that were originated remotely, due to peer restart. This field behaves like an SNMP counter. It only increases, never decreases, and is s…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.1.1.27

Circuit specific counters for this
Intermediate System.

isisCircuitCounterEntry row .1.3.6.1.4.1.629.10.10.1.5.2.1

An isisCircuitCounterEntry exists for each circuit
used by Integrated IS-IS on this system.

Indexes

isisSysInstance isisCircIndex isisCircuitType

Column	Syntax	OID
isisCircuitType What type of circuit saw these counts? The point to point Hello PDU includes both L1 and L2, and ISs form a single adjacency on point to point links. Thus we combine counts on point to point links into on…	Enumeration Enumerated Values: 1 lanlevel1 2 lanlevel2 3 p2pcircuit	.1.3.6.1.4.1.629.10.10.1.5.2.1.1
isisCircAdjChanges The number of times an adjacency state change has occurred on this circuit.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.2
isisCircNumAdj The number of adjacencies on this circuit.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.3
isisCircInitFails The number of times initialization of this circuit has failed. This counts events such as PPP NCP failures. Failures to form an adjacency are counted by isisCircRejAdjs.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.4
isisCircRejAdjs The number of times an adjacency has been rejected on this circuit.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.5
isisCircIDFieldLenMismatches The number of times an IS-IS control PDU with an ID field length different to that for this system has been received.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.6
isisCircMaxAreaAddrMismatches The number of times an IS-IS control PDU with a max area address field different to that for this system has been received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.7
isisCircAuthTypeFails The number of times an IS-IS control PDU with an auth type field different to that for this system has been received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.8
isisCircAuthFails The number of times an IS-IS control PDU with the correct auth type has failed to pass authentication validation.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.9
isisCircLANDesISChanges The number of times the Designated IS has changed on this circuit at this level. If the circuit is point to point, this count is zero.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.2.1.10

Information about IS-IS protocol traffic at one level
on one circuit in one direction.

isisPacketCounterEntry row .1.3.6.1.4.1.629.10.10.1.5.3.1

Information about IS-IS protocol traffic at one level
on one circuit in one direction

Indexes

isisSysInstance isisCircIndex isisPacketCountLevel isisPacketCountDirection

Column	Syntax	OID
isisPacketCountLevel The level at which these PDU counts have been collected.	Enumeration Enumerated Values: 0 none 1 level1 2 level2	.1.3.6.1.4.1.629.10.10.1.5.3.1.1
isisPacketCountDirection Were we sending or receiving these PDUs?	Enumeration Enumerated Values: 1 sending 2 receiving	.1.3.6.1.4.1.629.10.10.1.5.3.1.2
isisPacketCountIIHello The number of IS-IS Hello PDUs seen in this direction at this level. Point-to-Point IIH PDUs are counted at the lowest enabled level: at L1 on L1 or L1L2 circuits, and at L2 otherwise.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.3
isisPacketCountISHello The number of ES-IS Hello PDUs seen in this direction. ISH PDUs are counted at the lowest enabled level: at L1 on L1 or L1L2 circuits, and at L2 otherwise.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.4
isisPacketCountESHello The number of ES Hello PDUs seen in this direction. ESH PDUs are counted at the lowest enabled level: at L1 on L1 or L1L2 circuits, and at L2 otherwise.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.5
isisPacketCountLSP The number of IS-IS LSPs seen in this direction at this level.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.6
isisPacketCountCSNP The number of IS-IS CSNPs seen in this direction at this level.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.7
isisPacketCountPSNP The number of IS-IS PSNPs seen in this direction at this level.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.8
isisPacketCountUnknown The number of unknown IS-IS PDUs seen at this level.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.9
isisPacketCountDiscardedIIH The number of IIH PDUs that have been discarded. This field is always zero for outgoing PDUs.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.10
isisPacketCountDiscardedLSP The number of LSP PDUs that have been discarded by the SDC component of DC-ISIS. This field is always zero for outgoing PDUs.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.11
isisPacketCountDiscardedCSNP The number of CSNP PDUs that have been discarded by the SDC component of DC-ISIS. This field is always zero for outgoing PDUs.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.12
isisPacketCountDiscardedPSNP The number of PSNP PDUs that have been discarded by the SDC component of DC-ISIS. This field is always zero for outgoing PDUs.	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.5.3.1.13

The table of adjacencies to Intermediate Systems.

isisISAdjEntry row .1.3.6.1.4.1.629.10.10.1.6.1.1

Each entry corresponds to one adjacency to an
Intermediate System on this system.

Indexes

isisSysInstance isisCircIndex isisISAdjIndex

Column	Syntax	OID
isisISAdjIndex A unique value identifying the IS adjacency from all other such adjacencies on this circuit. This value is automatically assigned by the system when the adjacency is created.	Integer32 Constraints: range: 1-2000000000	.1.3.6.1.4.1.629.10.10.1.6.1.1.1
isisISAdjState The state of the adjacency.	Enumeration Enumerated Values: 1 down 2 initializing 3 up 4 failed	.1.3.6.1.4.1.629.10.10.1.6.1.1.2
isisISAdj3WayState The 3Way state of the adjacency. These are picked to match the historical on-the-wire representation of the 3Way state, and are not intended to match isisISAdjState.	Enumeration Enumerated Values: 0 up 1 initializing 2 down 3 failed	.1.3.6.1.4.1.629.10.10.1.6.1.1.3
isisISAdjNeighSNPAAddress The SNPA address of the neighboring system.	OSINSAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.629.10.10.1.6.1.1.4
isisISAdjNeighSysType The type of the neighboring system.	Enumeration Enumerated Values: 1 l1IntermediateSystem 2 l2IntermediateSystem 3 l1L2IntermediateSystem 4 unknown	.1.3.6.1.4.1.629.10.10.1.6.1.1.5
isisISAdjNeighSysID The system ID of the neighboring Intermediate System.	SystemID Type Constraints: range: 6	.1.3.6.1.4.1.629.10.10.1.6.1.1.6
isisISAdjNbrExtendedCircID The 4 byte Extended Circuit ID learned from the Neighbor during 3-way handshake, or 0.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.6.1.1.7
isisISAdjUsage How is the adjacency used? On a point-to-point link, this might be level1and2, but on a LAN, the usage will be level1 on the adjacency between peers at L1, and level2 for the adjacency between peers at L2.	Enumeration Enumerated Values: 0 reserved 1 level1 2 level2 3 level1and2	.1.3.6.1.4.1.629.10.10.1.6.1.1.8
isisISAdjHoldTimer The holding time in seconds for this adjacency. This value is based on received IIH PDUs and the elapsed time since receipt.	secondsUnsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.6.1.1.9
isisISAdjNeighPriority Priority of the neighboring Intermediate System for becoming the Designated Intermediate System.	ISPriority Type Constraints: range: 0..127	.1.3.6.1.4.1.629.10.10.1.6.1.1.10
isisISAdjLastUpTime If the isisISAdjState is in state 'up', the value of sysUpTime when the adjacency most recently entered the state 'up', or 0 if it has never been in state 'up'.	secondsSNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.629.10.10.1.6.1.1.11
isisISAdjRestartCapable Does the neighbor support restart signalling? This object is set to 'true' if the peer includes the restart TLV in IIH PDUs.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.6.1.1.12
isisISAdjPeerRestartState Is the peer currently restarting? Set to 'notRestarting' if the neighbor is not restarting (is not including a restart TLV in the IIH, or is not setting the RR bit). Set to 'restartingNoHel…	Enumeration Enumerated Values: 1 notRestarting 2 restartingNoHelp 3 helpingRestart	.1.3.6.1.4.1.629.10.10.1.6.1.1.13
isisISAdjSuppressed Has the peer requested that the adjacency be suppressed? If set to 'true', the adjacency will not be added to the local LSP. This object is set to 'true' if the peer sets the SA bit in the restart TLV in …	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.6.1.1.14
isisISAdjNeighLanID On a broadcast circuit, the LAN ID reported by the neighbor for the Designated Intermediate System on this circuit at this level. For a non-broadcast circuit, or if, for any reason, the neighbor is not partaking in the…	OctetString Constraints: range: 0-7	.1.3.6.1.4.1.629.10.10.1.6.1.1.15
isisISAdjNeighHostname The hostname corresponding to isisISAdjNeighSysID. This is the null string if isisSdEntMapHostnames is 'false' or if no hostname is known.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.6.1.1.16
isisISAdjNeighLanIDHostname The hostname corresponding to the system ID part of the isisISAdjNeighLanID object. This is the null string if the isisISAdjNeighLanID object is null, if isisSdEntMapHostnames is 'false', or if no hostnam…	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.629.10.10.1.6.1.1.17

This table contains the set of Area Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs.

isisISAdjAreaAddrEntry row .1.3.6.1.4.1.629.10.10.1.6.2.1

Each entry contains one Area Address reported by a
neighboring Intermediate System in its IIH PDUs.

Indexes

isisSysInstance isisCircIndex isisISAdjIndex isisISAdjAreaAddrIndex

Column	Syntax	OID
isisISAdjAreaAddrIndex An index for the areas associated with one neighbor. This provides a simple way to walk the table.	Integer32 Constraints: range: 1-2000000000	.1.3.6.1.4.1.629.10.10.1.6.2.1.1
isisISAdjAreaAddress One Area Address as reported in IIH PDUs received from the neighbor.	OSINSAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.629.10.10.1.6.2.1.2

This table contains the set of IP Addresses of
neighboring Intermediate Systems as reported in received
IIH PDUs.
          
If the isisSysRestrictLanAdjsToSubnet object in isisSysTable
is set to 'true' then for an IPv4 broadcast circuit, only
IP addresses on the same subnet as the local circuit are
included in this table.

isisISAdjIPAddrEntry row .1.3.6.1.4.1.629.10.10.1.6.3.1

Each entry contains one IP Address reported by a
neighboring Intermediate System in its IIH PDUs.

Indexes

isisSysInstance isisCircIndex isisISAdjIndex isisISAdjIPAddrIndex

Column	Syntax	OID
isisISAdjIPAddrIndex An index to this table which identifies the IP addresss to which this entry belongs.	Integer32 Constraints: range: 1-2000000000	.1.3.6.1.4.1.629.10.10.1.6.3.1.1
isisISAdjIPAddrType The type of one IP Address as reported in IIH PDUs received from the neighbor.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.6.3.1.2
isisISAdjIPAddrAddress One IP Address as reported in IIH PDUs received from the neighbor.	OctetString Constraints: range: 16-16 range: 4-4	.1.3.6.1.4.1.629.10.10.1.6.3.1.3

This table contains the set of protocols supported by
neighboring Intermediate Systems as reported in received
IIH PDUs.

isisISAdjProtSuppEntry row .1.3.6.1.4.1.629.10.10.1.6.4.1

Each entry contains one protocol supported by a
neighboring Intermediate System as reported in its IIH
PDUs.

Indexes

isisSysInstance isisCircIndex isisISAdjIndex isisISAdjProtSuppProtocol

Column	Syntax	OID
isisISAdjProtSuppProtocol One supported protocol as reported in IIH PDUs received from the neighbor.	SupportedProtocol Type Values: 129 iso8473 142 ipV6 204 ip	.1.3.6.1.4.1.629.10.10.1.6.4.1.1
isisISAdjProtSuppLocalSupport Whether local configuration allows use of this protocol to this neighbor. The value 'false' indicates that the protocol is unusable.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.6.4.1.5
isisISAdjProtSuppBfdStatus BFD session state for this protocol. The state inactive(2) indicates that the protocol is unusable for forwarding because a BFD session cannot be established or has failed.	Enumeration Enumerated Values: 0 notRequired 1 active 2 inactive 3 adminDown 4 noContact	.1.3.6.1.4.1.629.10.10.1.6.4.1.6

This table contains the set of topologies supported by
neighboring Intermediate Systems as reported in received IIH
PDUs.

isisISAdjMtSupportedEntry row .1.3.6.1.4.1.629.10.10.1.6.5.1

Each entry contains one topology reported by a
neighboring Intermediate System in its IIH PDUs.

Indexes

isisSysInstance isisCircIndex isisISAdjIndex isisISAdjMtSuppMtId

Column	Syntax	OID
isisISAdjMtSuppMtId A topology that is supported on this adjacency.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.6.5.1.4
isisISAdjMtSuppLocalSupport Whether this topology is also supported locally on this circuit. The value is 'true' if there is a corresponding row in the isisMtCircStatusTable with isisMtCircStatusOperState set to 'operStatusUp'. In …	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.629.10.10.1.6.5.1.5

The table of IP Reachable Addresses to networks,
subnetworks or hosts, learned automatically.
          
DC-ISIS does not support the manual addition of entries
using this table.  This table is read-only.
          
In order to specify reachable addresses manually,
configure a static route in the Address Family Manager,
and configure the AFM to pass the static route into
DC-ISIS.
          
In DC-RTM, this can be done using the static routes
table (rtmStaticRtTable), and the redistribution table
(rtmRedistTable).

isisIPRAEntry row .1.3.6.1.4.1.629.10.10.1.8.1.1

Each entry defines an IP Reachable Address to a network,
subnetwork or host.

Each IP Reachable Address may have multiple entries in the
table, one for each equal cost path to the reachable address.

Indexes

isisSysInstance isisIPRADestType isisIPRADest isisIPRADestPrefixLen isisIPRANextHopIndex

Column	Syntax	OID
isisIPRADestType The type of this IP Reachable Address.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.8.1.1.1
isisIPRADest The destination of this IP Reachable Address. This is either a network address, subnetwork address or host address.	OctetString Constraints: range: 16-16 range: 4-4	.1.3.6.1.4.1.629.10.10.1.8.1.1.2
isisIPRADestPrefixLen The length of the IP Netmask for Reachability Address.	Unsigned32 Constraints: range: 0-128	.1.3.6.1.4.1.629.10.10.1.8.1.1.3
isisIPRANextHopIndex Index of next hop. Used when there are multiple Equal Cost Multipath alternatives for the same destination.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.629.10.10.1.8.1.1.4
isisIPRANextHopType The type of the IP next hop address. For the DC-ISIS implementation, this field is not stored and is therefore not returned in GETs for this MIB.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.629.10.10.1.8.1.1.5
isisIPRANextHop The IP next hop to this destination. For the DC-ISIS implementation, this field is not stored and is therefore not returned in GETs for this MIB.	OctetString Constraints: range: 16-16 range: 4-4	.1.3.6.1.4.1.629.10.10.1.8.1.1.6
isisIPRAType The type of this IP Reachable Address. Those of type manual are created by the network manager. Those of type automatic are created through propagation of routing information from another routing protocol. …	Enumeration Enumerated Values: 1 manual 2 automatic 3 both	.1.3.6.1.4.1.629.10.10.1.8.1.1.7
isisIPRAExistState The state of this IP Reachable Address. This object follows the ExistenceState behavior.	SNMPv2-TCRowStatus Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.629.10.10.1.8.1.1.8
isisIPRAAdminState The administrative state of the IP Reachable Address. This object follows the AdminState behavior.	AdminState Type Values: 1 on 2 off	.1.3.6.1.4.1.629.10.10.1.8.1.1.9
isisIPRAMetric The metric value for reaching the specified destination over this circuit.	DefaultMetric Type Constraints: range: 0..63	.1.3.6.1.4.1.629.10.10.1.8.1.1.10
isisIPRAMetricType Indicates whether the metric is internal or external.	MetricType Type Values: 1 internal 2 external	.1.3.6.1.4.1.629.10.10.1.8.1.1.11
isisIPRAFullMetric The wide metric value for reaching the specified destination over this circuit.	FullMetric	.1.3.6.1.4.1.629.10.10.1.8.1.1.12
isisIPRASNPAAddress The SNPA Address to which a PDU may be forwarded in order to reach a destination which matches this IP Reachable Address. DC-ISIS does not support this field.	OSINSAddress Type Constraints: range: 0..20	.1.3.6.1.4.1.629.10.10.1.8.1.1.13
isisIPRASourceType The origin of this route.	Enumeration Enumerated Values: 1 static 2 direct 3 ospfv2 4 ospfv3 5 isis 6 rip 7 igrp 8 eigrp 9 bgp 10 other	.1.3.6.1.4.1.629.10.10.1.8.1.1.14
isisIPRAMtId The topology that this reachable address is in.	Integer32 Constraints: range: 0-4095	.1.3.6.1.4.1.629.10.10.1.8.1.1.16