CTRON-ETHERNET-PARAMETERS-MIB Table View

Provides a list of definitions and control objects over any 10BASE-T,
100BASE-TX, or 1000BASE-X Cabletron interface that supports 
auto-negotiation as described by the aforementioned standards.

ctAutoNegCtlEntry row .1.3.6.1.4.1.52.4.1.2.4.2.1.1.1

Defines a particular entry containing objects pertaining to
definition and control over interfaces supporting Auto-Negotiation.

Indexes

CTIF-EXT-MIBctIfPortIfNumber CTIF-EXT-MIBctIfPortPortNumber

Column	Syntax	OID
ctAutoNegAdminStatusmandatory This object controls whether Auto-Negotiation is enabled for the specified port. If Auto-Negotiation is disabled the port will revert to the speed, duplex and flow control settings specified by their associated leaves…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.1
ctAutoNegRemoteSignallingmandatory This object indicates whether the remote end of the link is operating Auto-Negotiation signalling or not.	Enumeration Enumerated Values: 1 detected 2 notdetected	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.2
ctAutoNegAutoConfigmandatory This object indicates whether Auto-Negotiation signalling is in progress or has completed.	Enumeration Enumerated Values: 1 other 2 configuring 3 complete 4 disabled 5 paralleldetectfailed	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.3
ctAutoNegLocalTechnologyAbilitymandatory This indicates the technology ability of the local hardware. The value is a sum. This sum initially takes the value zero. Then, for each technology, T, that the port supports, 2 raised to (T - 1) is adde…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.4
ctAutoNegAdvertisedTechnologyAbilitymandatory Indicates the advertised ability of the local hardware, but only becomes active on ports that have auto-negotiation enabled. The value is a sum. This sum initially takes the value zero. Then, for each …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.5
ctAutoNegReceivedTechnologyAbilitymandatory Indicates the advertised ability of the remote hardware, or link partner. The value is a sum. This sum initially takes the value zero. Then, for each technology, T, that the link partner supports, 2 ra…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.52.4.1.2.4.2.1.1.1.6

Provides a list of statistic and control objects over 10BASE-X, 
100BASE-X and 1000BASE-X Cabletron interfaces that support flow 
control as described by IEEE Std 802.3, 1998 Edition.

ctFlowCtlEntry row .1.3.6.1.4.1.52.4.1.2.4.2.2.1.1

Defines a particular entry containing objects pertaining to
definition and control over Cabletron flow control capable interfaces.

Indexes

CTIF-EXT-MIBctIfPortIfNumber CTIF-EXT-MIBctIfPortPortNumber

Column	Syntax	OID
ctFlowCtlHalfDuplexAdminStatusmandatory The administrative status requested by management for back pressure on this port. Back pressure is a collision based flow control mechanism used in half duplex configurations. The value of enabled(1) indicates that …	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.1
ctFlowCtlHalfDuplexOperStatusmandatory The current operational status of back pressure on this port.	Enumeration Enumerated Values: 1 enabled 2 disabled 3 notsupported	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.2
ctEtherSupportedPauseModesmandatory This indicates the frame based modes of full duplex flow control for this port. The value is a sum. This sum initially takes the value zero. Then, for each mode, M, that the port supports, 2 raised to (M…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.3
ctFlowCtlPauseAdminStatusmandatory The administrative status requested by management for frame based flow control on this port. For 10 Mb and 100 Mb ports the value of symmetric(1) indicates that if Auto-Negotiation is supported for this port, that th…	Enumerationr/w Enumerated Values: 1 symmetric 2 asymmetricRx 3 asymmetricTx 4 disabled 5 autonegotiate	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.4
ctFlowCtlPauseOperStatusmandatory The current operational status of full duplex flow control on this port. A value of unknown(5) will be returned for any port which has a Pause Frame Admin Status of autonegotiate(5), as specified by ctFlowCtlPauseAdm…	Enumeration Enumerated Values: 1 symmetric 2 asymmetricRx 3 asymmetricTx 4 disabled 5 unknown 6 notsupported	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.5
ctFlowCtlPauseTimermandatory A 2 octet, unsigned integer containing the length of time for which the receiving station is requested to inhibit data frame transmission. The pause time is measured in units of pause_quanta, equal to 512 bit times of t…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.6
ctFlowCtlRxPauseFramesmandatory The number of pause frames received on this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.7
ctFlowCtlTxPauseFramesmandatory The number of pause frames transmitted from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.52.4.1.2.4.2.2.1.1.8

Provides a list of speed and duplex control objects over 10BASE-X, 
100BASE-X and 1000 BASE-X Cabletron Ethernet interfaces.

ctEtherManualConfigEntry row .1.3.6.1.4.1.52.4.1.2.4.2.3.1.1

Defines a particular entry containing objects pertaining to
definition and control over Cabletron Ethernet interfaces.

Indexes

CTIF-EXT-MIBctIfPortIfNumber CTIF-EXT-MIBctIfPortPortNumber

Column	Syntax	OID
ctEtherSupportedSpeedmandatory This indicates the supported speeds for the port. The value is a sum. This sum initially takes the value zero. Then, for each speed, S, that the port supports, 2 raised to (S - 1) is added to the sum. …	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.1
ctEtherSpeedAdminStatusmandatory The administrative status requested by management for the speed of this port. The value of tenmegabit(2) indicates that if Auto-Negotiation is disabled for this port, that the port will operate at a speed of 10 megab…	Enumerationr/w Enumerated Values: 2 tenmegabit 3 hundredmegabit 4 gigabit	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.2
ctEtherSpeedOperStatusmandatory This object indicates the current speed of the Ethernet port.	Enumeration Enumerated Values: 1 unknown 2 tenmegabit 3 hundredmegabit 4 gigabit	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.3
ctEtherSupportedDuplexmandatory This object indicates the duplex modes supported by this port. A value of halfduplex(1) indicates that the port only supports half duplex operation. A value of fullduplex(2) indicates that the port only supports full d…	Enumeration Enumerated Values: 1 halfduplex 2 fullduplex 3 halfandfullduplex	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.4
ctEtherDuplexAdminStatusmandatory The administrative status requested by management for the duplex of this port. The value of halfduplex(2) indicates that if Auto-Negotiation is disabled for this port, that the port will operate in half duplex, provi…	Enumerationr/w Enumerated Values: 2 halfduplex 3 fullduplex	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.5
ctEtherDuplexOperStatusmandatory This object indicates the current duplex of the Ethernet port.	Enumeration Enumerated Values: 1 unknown 2 halfduplex 3 fullduplex	.1.3.6.1.4.1.52.4.1.2.4.2.3.1.1.6