CISCO-WIRELESS-IF-MIB Table View

This table provides facilities to establish loopback points in the
radio hardware to exercise various sections of the hardware.

cwrLoopbackEntry row .1.3.6.1.4.1.9.9.136.1.1.1.1.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrLocalLoopbackPoint This object represents the point in the system where the data signal is looped back. none(0) - no loopback codec(1) - loopback at the Encoder/Decoder module. This exerci…	Enumerationr/w Enumerated Values: 0 none 1 codec 2 framer 3 fir 4 if 5 rf 6 rfDiversity 7 ifMain 8 ifDiversity	.1.3.6.1.4.1.9.9.136.1.1.1.1.1.1

This table provides facilities to redirect a portion of the signal
being processed by a DSP to a scope port on the radio. An
oscilloscope may be connected to the scope port to analyze the 
signal.

cwrScopePortEntry row .1.3.6.1.4.1.9.9.136.1.1.1.2.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrScopePortOn If set to true(1), then the DSP identified by cwrScopePortDsp, will redirect a portion of the output signal for the attribute identified by cwrScopeAttribute to the scope port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.1.1.2.1.1
cwrScopePortDsp This identifies the DSP that should redirect a portion of the signal data to the scope port.	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.9.9.136.1.1.1.2.1.2
cwrScopePortAttribute This represents the attribute to be redirected to the scope port. The attributes that may be redirected to scope port is the same as that identified in cwrSnapshotType.	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.1.1.2.1.3

This table contains information about the radio common to both 
the transmit and receive sides.

cwrRadioBaseEntry row .1.3.6.1.4.1.9.9.136.1.3.1.1

There exists one such entry for every interface in the
ifTable which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex as
defined in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrAcquisitionMode This object specifies whether the radio should act as the master or as the slave. The slave radio tracks the master's frequency.	Enumerationr/w Enumerated Values: 1 master 2 slave	.1.3.6.1.4.1.9.9.136.1.3.1.1.2
cwrSelfTest This object specifies the whether self test should be executed and if so whether to do it every time the radio link is started. Any changes made to this object will reflected the next time the radio link is started. …	Enumerationr/w Enumerated Values: 1 off 2 once 3 always	.1.3.6.1.4.1.9.9.136.1.3.1.1.3
cwrBasePrivacySupport This object specifies whether the Baseline Privacy feature is available for use on this radio interface. If true then privacy is supported.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.3.1.1.4
cwrTxRfIndex This object specifies the index into the cwrRfTable identifying the antenna used for transmission. This index will be 0 if the associated transmit antenna is not present.	CISCO-WIRELESS-TC-MIBCwrRFZeroIndex Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.3.1.1.5
cwrRx1RfIndex This object specifies the index of the first receive antenna identified by the cwrRfTable. This index will be 0 if the associated receive antenna is not present.	CISCO-WIRELESS-TC-MIBCwrRFZeroIndex Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.3.1.1.6
cwrRx2RfIndex This object specifies the index of the second receive antenna in the cwrRfTable. This index will be 0 if the associated receive antenna is not present.	CISCO-WIRELESS-TC-MIBCwrRFZeroIndex Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.3.1.1.7
cwrClockRefExt When this object is set to true(1), the wireless radio uses a 10MHz external reference clock.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.3.1.1.8
cwrAntAlignment For normal operation this should be set to false(2). If it set true(1), then the radio link is placed in antenna alignment mode. In this mode control signals are sent to the RF resource which enables the operator to mon…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.3.1.1.9

This table contains information about the currently configured
physical layer.  These configuration paramters must match the 
    corresponding configuration parameter at the remote end for
    the wireless link to be established.

cwrRadioPhyEntry row .1.3.6.1.4.1.9.9.136.1.3.2.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex
as defined in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrNumRxAntenna This object specifies the number of antennas to be used to receive the wireless transmissions.	Integer32r/w Constraints: range: 1-2	.1.3.6.1.4.1.9.9.136.1.3.2.1.1
cwrBandwidth This object specifies the bandwidth to use. Given bandwidth, the actual throughput of the radio link is determined by the cwrThroughput setting.	HzInteger32r/w Constraints: range: 0-500000000	.1.3.6.1.4.1.9.9.136.1.3.2.1.2
cwrThroughput This represents an throughput expected of the identified radio link. There are 3 possible settings. The settings provide a tradeoff between bandwidth and the reliability of the radio link. The settings are: high(…	Enumerationr/w Enumerated Values: 1 high 2 medium 3 low	.1.3.6.1.4.1.9.9.136.1.3.2.1.3
cwrOperatingBand This object represents the portion of the frequency spectrum in which the radio PHY will operate. bandUNII(1) - The U-NII (Unlicensed National Information Infrastructure) band re…	Enumerationr/w Enumerated Values: 1 bandUNII 2 bandMMDS 3 bandOther	.1.3.6.1.4.1.9.9.136.1.3.2.1.4
cwrTxFrequency This object represents the center frequency that will be used to transmit data over the radio PHY. The specified transmit frequency must match the operating band and the capability of the RF resource connected to the …	10KhzInteger32r/w Constraints: range: 0-6000000	.1.3.6.1.4.1.9.9.136.1.3.2.1.5
cwrRxFrequency This object represents the center frequency that will be used to receive transmissions over the radio PHY. The specified receive frequency must match the operating band and the capability of the RF resource connected to…	10KhzInteger32r/w Constraints: range: 0-6000000	.1.3.6.1.4.1.9.9.136.1.3.2.1.6
cwrTxPower This object represents the power that the antenna will transmit. The minimum average transmit power for the U-NII or MMDS band is 0.01 microwatts (-80 dBm). Maximum average transmit power: For the MMDS band is 2 Wat…	dBm - decibel milliwattsInteger32r/w Constraints: range: -80-50	.1.3.6.1.4.1.9.9.136.1.3.2.1.7
cwrCableLoss This object represents the measured loss in signal power in dB that is imposed by the cable connecting the radio to the antenna head. This value enables the hardware to compensate for the cable loss by adjusting the …	dB - decibelInteger32r/w Constraints: range: 0-50	.1.3.6.1.4.1.9.9.136.1.3.2.1.8
cwrOpStatus This represents the current state of a radio Link. notOperational(1): The link is not operational. selftest(2) : Power on self test in progress download(3): Image download is in progress. txOnly(4): The r…	Enumeration Enumerated Values: 1 notOperational 2 selftest 3 download 4 txOnly 5 acquiring 6 receiveUp 7 transmitUp 8 linkOperational	.1.3.6.1.4.1.9.9.136.1.3.2.1.9
cwrCableLossDiversity This object represents the measured loss in signal power in dB that is imposed by the cable connecting the radio to the antenna head. This value enables the hardware to compensate for the cable loss by adjusting the …	dB - decibelInteger32r/w Constraints: range: 0-50	.1.3.6.1.4.1.9.9.136.1.3.2.1.10
cwrBurstSize This object defines the time duration of the data burst sent over the air. The burst size is dependant on the capability of the ODU which is represented by the cwrBurstSizeGroup variable in the cwrRfTable. The user m…	Enumerationr/w Enumerated Values: 1 small 2 medium 3 large	.1.3.6.1.4.1.9.9.136.1.3.2.1.11

This table contains information about the radio PHY quality 
control parameters. Note that the parameters in this table are 
automatically determined by the parameters configured in the 
cwrRadioPhyTable. These parameters may further be used to tune 
the characteristics when needed.

cwrPhyQualityEntry row .1.3.6.1.4.1.9.9.136.1.4.1.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex as
defined in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrArqPctBw This object specifies the percentage of the total radio PHY bandwidth available to the ARQ engine. Some or all of this allocated bandwidth is used to when detected errors are corrected. The percentage will be approxi…	0.01 percentInteger32r/w Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.4.1.1.1
cwrArqVoiceLatency This object identifies the latency value for voice data.	millisecondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.4.1.1.2
cwrArqDataLatency This object specifies the expected latency values for data. Reducing the latency, provides the ARQ engine less time to correct codeword errors. So if latency is reduced sufficiently, the data throughput will get effecte…	millisecondsInteger32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.4.1.1.3
cwrArqBurstSize This object specifies the maximum number of consecutive ARQ codewords that will be transmitted. ARQ codewords are transmitted for error correction. When an ARQ codeword is transmitted, a data codeword cannot be trans…	Integer32r/w Constraints: range: 1-63	.1.3.6.1.4.1.9.9.136.1.4.1.1.4
cwrArqTypicalBitRate This object specifies the typical error free bit rate that is possible on this link given the current configuration as specified in the cwrRadioPhyTable. If the radio channel is excessively noisy then the bit rate wi…	bits/secInteger32 Constraints: range: 0-45000000	.1.3.6.1.4.1.9.9.136.1.4.1.1.5
cwrArqMinBitRate This object specifies the minimum error free bit rate that is supported on this link given the current configuration as specified in the cwrRadioPhyTable and the settings in this table.	bits/secInteger32 Constraints: range: 0-45000000	.1.3.6.1.4.1.9.9.136.1.4.1.1.6
cwrArqMaxLatencyJitter This object specifies the maximum latency jitter introduced by the ARQ engine, based on the settings defined in this table.	microsecondsInteger32 Constraints: range: 1-22000	.1.3.6.1.4.1.9.9.136.1.4.1.1.7
cwrArqReset This object when set to true will force the PHY quality parameters to be reset from the cwrRadioPhyTable. Reading this object will always return false. This is useful when arbitrary changes to the ARQ parameters have to…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.4.1.1.8
cwrArqOn This object when set to true will enable the Automatic Repeat Query subsystem. Disabling the ARQ subsystem disables a major error correction mechanism of the radio, due to which an operating radio PHY may suffer larg…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.4.1.1.9

This provides information on the number of byte
detected and corrected by the ARQ engine.
The ARQ engine can correct up to 9 consecutive byte errors.
This table keeps a count of the number of byte errors corrected
over time.
The values in this table are cumulated from link power up.

cwrPhyCorrectedBytesEntry row .1.3.6.1.4.1.9.9.136.1.4.2.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex as
defined in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrArq1ByteErrs This object identifies the number of 1 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.1
cwrArq2ByteErrs This object identifies the number of consecutive 2 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.2
cwrArq3ByteErrs This object identifies the number of consecutive 3 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.3
cwrArq4ByteErrs This object identifies the number of consecutive 4 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.4
cwrArq5ByteErrs This object identifies the number of consecutive 5 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.5
cwrArq6ByteErrs This object identifies the number of consecutive 6 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.6
cwrArq7ByteErrs This object identifies the number of consecutive 7 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.7
cwrArq8ByteErrs This object identifies the number of consecutive 8 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.8
cwrArq9ByteErrs This object identifies the number of consecutive 9 byte errors that were corrected since the the radio link reached linkOperational state.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.136.1.4.2.1.9

This table contains information about the state of the 
radio frequency resources used by the radio link.

cwrRfEntry row .1.3.6.1.4.1.9.9.136.1.5.1.1

This represents one entry in the cwrRfTable. This table is largely
a read only table which provides details on the state of radio
frequency resources available on the system.
Physically each RF resource may be realized…

Indexes

IF-MIBifIndex cwrRfIndex

Column	Syntax	OID
cwrRfIndex This object, along with ifIndex, represents the index of this entry in the cwrRfTable.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.9.9.136.1.5.1.1.1
cwrRfResIndex This object represents the index into CwrRfEntityTable. This index identifies the radio frequency resource.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.5.1.1.2
cwrRFOpMode This object indicates if this RF resource is being used to either receive, transmit, or both.	Enumeration Enumerated Values: 0 rxOnly 1 txOnly 2 rxAndTx	.1.3.6.1.4.1.9.9.136.1.5.1.1.3
cwrTxFreqRangeMin This object represents the minimum frequency at which this RF resource can transmit.	10 kHzInteger32 Constraints: range: 215000-582500	.1.3.6.1.4.1.9.9.136.1.5.1.1.4
cwrTxFreqRangeMax This object represents the maximum frequency at which this RF resource can transmit.	10 kHzInteger32 Constraints: range: 215000-582500	.1.3.6.1.4.1.9.9.136.1.5.1.1.5
cwrRxFreqRangeMin This object represents the lowest transmission frequency this RF resource can receive.	10 kHzInteger32 Constraints: range: 215000-582500	.1.3.6.1.4.1.9.9.136.1.5.1.1.6
cwrRxFreqRangeMax This object represents the highest transmission frequency that this RF resource can receive.	10 kHzInteger32 Constraints: range: 215000-582500	.1.3.6.1.4.1.9.9.136.1.5.1.1.7
cwrMinTxPower This object represents the minimum power that the RF subsystem can supply the antenna.	dBm Decibel milliwattsInteger32 Constraints: range: -80-33	.1.3.6.1.4.1.9.9.136.1.5.1.1.8
cwrMaxTxPower This object represents the maximum power that the RF subsystem can supply the antenna.	dBm Decibel milliwattsInteger32 Constraints: range: -80-33	.1.3.6.1.4.1.9.9.136.1.5.1.1.9
cwrRfTxOscState This object represents the state of the transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.136.1.5.1.1.10
cwrRfAntIndex This object represents the index into the cwrAntennaTable. This object may be 0 if the cwrAntennaTable is not available.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.136.1.5.1.1.11
cwrRfRxOscState This object represents the state of the receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.136.1.5.1.1.12
cwrRfTemperature This object represents the current temperature of the RF unit.	Degrees CentigradeInteger32 Constraints: range: -40-100	.1.3.6.1.4.1.9.9.136.1.5.1.1.13
cwrRfSupplyVoltageState This object specifies whether the voltage supply to the RF unit is within specifications or not.	Enumeration Enumerated Values: 1 withinSpecification 2 outsideSpecification	.1.3.6.1.4.1.9.9.136.1.5.1.1.14
cwrRfStatus This object specifies whether the RF resource is functioning properly or not. If it is functioning properly then it will be online(1), else offline(2).	Enumeration Enumerated Values: 1 online 2 offline	.1.3.6.1.4.1.9.9.136.1.5.1.1.15
cwrRfControlChannelStatus Each RF resource has an associated control channel. The control channel is used to send/receive control information to the RF resource. For the RF resouce to operate properly, the control channel must be established. …	Enumeration Enumerated Values: 1 ok 2 notOk	.1.3.6.1.4.1.9.9.136.1.5.1.1.16
cwrBurstSizeGroup This object indicates the range or burst sizes supported by the ODU. This information is read from the ODU EEPROM. The user may set the cwrBurstSize MIB object in the cwrRadioPhyTable based on the value of this obj…	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.9.9.136.1.5.1.1.17

This table contains information about the state of the 
intermediate frequency subsystem on the wireless radio.

cwrIntFreqEntry row .1.3.6.1.4.1.9.9.136.1.5.2.1

This represents one entry in the cwrIntFreqTable.
This table is largely a read only table which provides details
on the state of the intermediate frequency subsystem available on
the wireless radio.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrIfTxOscState This object represents the state of the IF transmit oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.136.1.5.2.1.1
cwrIfRxOscState This object represents the state of the IF receive oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.136.1.5.2.1.2
cwrIfRefOscState This object represents the state of the IF reference oscillator. The oscillator must be in oscillatorOk(1) state for the system to function properly.	CISCO-WIRELESS-TC-MIBCwrOscState Type Values: 1 oscillatorOk 2 osccillatorBad	.1.3.6.1.4.1.9.9.136.1.5.2.1.3
cwrIfResIndex This object represents the index into CwrIntFreqEntityTable. It identifies the intermediate frequency resource.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.5.2.1.4
cwrIfInpFreq This object represents the IF input frequency.	10 kHzInteger32 Constraints: range: 100-10000	.1.3.6.1.4.1.9.9.136.1.5.2.1.5
cwrIfOutFreq This object represents the IF output frequency.	10 kHzInteger32 Constraints: range: 20000-50000	.1.3.6.1.4.1.9.9.136.1.5.2.1.6

This table contains threshold values that are the trigger points 
for controlling the collection of the Link Metrics such as 
Codeword Errored Seconds and others.

cwrLinkMetricsThreshEntry row .1.3.6.1.4.1.9.9.136.1.6.1.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex as
defined in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrLinkCwESThresh If the number of Codeword Errors detected in a duration of 1 Operational second, is greater than this value then that second is counted as an Errored Second.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.1
cwrLinkLowCwDSThresh This object specifies low degraded second threshold. When the number of codeword errors detected are greater or equal than this value and less than cwrLinkHighCwDSThresh then that second is counted as a Codeword Degrad…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.2
cwrLinkHighCwDSThresh This object specifies high degraded second threshold. When then number of codeword errors detected are greater than this value then that second is counted as a Codeword Severely Errored Second.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.3
cwrLinkCSESThresh When the number of severely errored codewords detected consecutively in one second equals this threshold value, the second is counted as a Consecutively Severely Errored Second.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.4
cwrLink1HrESAlarmThresh This object specifies the one hour Codeword Error Second threshold. When the number of Codeword Error Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time measurem…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.5
cwrLink1HrSESAlarmThresh This object specifies the one hour Codeword Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.6
cwrLink1HrCSESAlarmThresh This object specifies the one hour Codeword Consecutively Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh …	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.7
cwrLink1HrDCMAlarmThresh This object specifies the one hour Degraded Codeword Minute threshold. When the number of Degraded Codeword Minutes in a 1 Operational Hour period exceeds this limit cwrTrapLink1HrThresh trap will be generated. Time me…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.8
cwrLink24HrESAlarmThresh This object specifies the 24 hour Codeword Error Second threshold. When the number of Codeword Error Seconds in a 24 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time measure…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.9
cwrLink24HrSESAlarmThresh This object specifies the one hour Codeword Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will b…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.10
cwrLink24HrCSESAlarmThresh This object specifies the one hour Codeword Consecutively Severely Errored Seconds threshold. When the number of Codeword Severely Errored Seconds in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.11
cwrLink24HrDCMAlarmThresh This object specifies the one hour Degraded Codeword Minute threshold. When the number of Degraded Codeword Minutes in a 1 Operational Hour period exceeds this limit cwrTrapLink24HrThresh trap will be generated. Time me…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.1.1.12

This table contains metrics used to measure the quality of the 
radio link identified by the ifIndex. The metrics in this table 
are cumulated since the last time the system powered up.

cwrCumulativeMetricsEntry row .1.3.6.1.4.1.9.9.136.1.6.2.1

There exists one such entry for every interface in the ifTable
which has an ifType of propWirelessP2P(157).

Each of these entries are indexed by the value of ifIndex as defined
in RFC2863.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrAvailableSeconds This object represents the number of Available Seconds cumulated since the link was powered up. It is equal to: Error Free Seconds + Errored Seconds - Severely Errored Seconds.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.1
cwrUnAvailableSeconds This object represents the number of seconds that the link was not available for use. It is equal to: Severely Errored Seconds + Sync Loss Seconds.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.2
cwrSyncLossSeconds This object represents the number of Link Admin Up Seconds during which the radio link was out of sync with the remote end.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.3
cwrPctErrorFreeSeconds This object represents the ratio of cumulative Codeword Error Free Seconds (EFS) to Link Admin Up seconds, expressed as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.4
cwrPctErroredSeconds This object represents the ratio of cumulative Codeword Errored Seconds (ES) to Link Admin Up seconds, expressed as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.5
cwrPctSeverelyErroredSeconds This object represents the ratio of cumulative Codeword Severely Errored Seconds (SES) to Link Admin Up seconds, expressed as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.6
cwrPctAvailSeconds This object represents the ratio of cumulative Available seconds to Link Admin Up seconds, expressed as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.7
cwrPctCwDegradedMinutes This object represents the ratio of cumulative Codeword Degraded Minutes to Link Admin Up seconds, expressed as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.8
cwrSyncSuccessCount This object represents number of times the radio link successfully synchronized with the far end.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.9
cwrSyncFailureCount This object represents number of times the link attempted to synchronize with the far end but failed to.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.10
cwrManagedSyncLoss This object represents number of times the radio link layer was shutdown by operator intervention or a higher layer protocol.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.11
cwrAutomaticSyncLoss This object represents number of times the radio link was synchronized but lost synchronization with the remote end without manual or higher layer protocol layer intervention.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.12
cwrLastSyncSuccessTime This object represents elapsed time since the radio link successfully synchronized with the remote end.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.136.1.6.2.1.13
cwrLastSyncFailTime This object represents elapsed time since the radio link lost synchronization with the remote end.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.136.1.6.2.1.14
cwrEffectivePhyDataRate This object represents the effective data throughput of this link while the link was synchronized.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.2.1.15
cwrPctEffectivePhyDataRate This object represents the ratio of total error free codewords received to the total codewords received as a percentage.	0.01 percentUnsigned32 Constraints: range: 1-10000	.1.3.6.1.4.1.9.9.136.1.6.2.1.16

This table contains metrics collected over the duration of 
24 hours.
This table is updated once every day for 32 days. Therefore, this
table will have a maximum of 32 entries that provide cumulative 
status of the link, identified by ifIndex.

cwr24HrMetricsEntry row .1.3.6.1.4.1.9.9.136.1.6.3.1

This represents one entry in the cwr24HrMetricsTable
indexed by ifIndex and cwr24HrMetricsIndex.

The first entry in the table (cwr24HrMetricsIndex = 1) represents
the chronologically oldest data available.

Indexes

IF-MIBifIndex cwr24HrMetricsIndex

Column	Syntax	OID
cwr24HrMetricsIndex Each entry represents the sum of the metrics from the previous 24 hour entry + the 24 hour period immdeiately prior to the most recent update.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.9.9.136.1.6.3.1.1
cwr24HrUpdateTime This object represents time in seconds since system power up at which time this entry was updated.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.6.3.1.2
cwr24HrErrorFreeSeconds This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErrorFreeSecond	.1.3.6.1.4.1.9.9.136.1.6.3.1.3
cwr24HrErroredSeconds This object represents the number of Codeword Error Seconds (ES) detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.3.1.4
cwr24HrSevErroredSeconds This object represents the number of Codeword Severely Error Seconds (SES) detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwSeverelyErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.3.1.5
cwr24HrConsecSvErrSeconds This object represents the number of Codeword Consecutively Severely Error Seconds (CSES) detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwConsecutiveSevErrSecond	.1.3.6.1.4.1.9.9.136.1.6.3.1.6
cwr24HrDegradedMinutes This object represents the number of Codeword Degraded Minutes (DM) detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwDegradedMinute	.1.3.6.1.4.1.9.9.136.1.6.3.1.7
cwr24HrTotalErroredCodewords This object represents the total number of errored codewords detected since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.3.1.8
cwr24HrTotalCodewords This object represents the total number of codewords received on this link since link power up, captured at cwr24HrUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.3.1.9

This table contains metrics collected over the duration of one 
hour.
This table will have a maximum of 24 entries providing cumulative 
status of the link, identified by ifIndex, over the past 24 hours.
This table is updated once every hour.

cwr1HrMetricsEntry row .1.3.6.1.4.1.9.9.136.1.6.4.1

This represents one entry in the cwr1HrMetricsTable indexed by
ifIndex and cwr1HrMetricsIndex.

The first entry in the table (cwr1HrMetricsIndex = 1) represents
the chronologically oldest data available.

Indexes

IF-MIBifIndex cwr1HrMetricsIndex

Column	Syntax	OID
cwr1HrMetricsIndex Each entry represents the sum of the metrics from the previous 1 hour entry + the 1 hour period immdeiately prior to the most recent update.	Integer32 Constraints: range: 1-24	.1.3.6.1.4.1.9.9.136.1.6.4.1.1
cwr1HrUpdateTime This object represents time in seconds since system power up at which time this entry was updated.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.6.4.1.2
cwr1HrErrorFreeSeconds This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErrorFreeSecond	.1.3.6.1.4.1.9.9.136.1.6.4.1.3
cwr1HrErroredSeconds This object represents the cumulative Codeword Errored Seconds (ES) detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.4.1.4
cwr1HrSevErroredSeconds This object represents the cumulative Codeword Severely Errored Seconds (SES) detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwSeverelyErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.4.1.5
cwr1HrConsecSvErrSeconds This object represents the cumulative Codeword Consecutive Severely Errored Seconds (CSES) detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwConsecutiveSevErrSecond	.1.3.6.1.4.1.9.9.136.1.6.4.1.6
cwr1HrDegradedMinutes This object represents the cumulative Codeword Degraded Minutes detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwDegradedMinute	.1.3.6.1.4.1.9.9.136.1.6.4.1.7
cwr1HrErroredCodewords This object represents the cumulative errored codewords detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.4.1.8
cwr1HrTotalCodewords This object represents the cumulative total received codewords detected since link power up, captured at cwr1HrUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.4.1.9

This table contains metrics collected over the duration of one 
minute.
This table will have a maximum of 60 entries providing cumulative 
status of the link, identified by ifIndex, over the past 60 minutes.
This table is updated once every minute.

cwr1MinMetricsEntry row .1.3.6.1.4.1.9.9.136.1.6.5.1

This represents one entry in the cwr1MinMetricsTable indexed by
ifIndex and cwr1MinMetricsIndex.

The first entry in the table (cwr1MinMetricsIndex = 1) represents
the chronologically oldest data available.

Indexes

IF-MIBifIndex cwr1MinMetricsIndex

Column	Syntax	OID
cwr1MinMetricsIndex Each entry represents the sum of the metrics from the previous 1 minute entry + the 1 minute period immdeiately prior to the most recent update.	Integer32 Constraints: range: 1-60	.1.3.6.1.4.1.9.9.136.1.6.5.1.1
cwr1MinUpdateTime This object represents time in seconds since system power up at which time this entry was updated.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.6.5.1.2
cwr1MinErrorFreeSeconds This object represents the cumulative Codeword Error Free Seconds (EFS) detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErrorFreeSecond	.1.3.6.1.4.1.9.9.136.1.6.5.1.3
cwr1MinErroredSeconds This object represents the cumulative Codeword Errored Seconds (ES) detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.5.1.4
cwr1MinSevErroredSeconds This object represents the cumulative Codeword Severely Errored Seconds (SES) detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwSeverelyErroredSecond	.1.3.6.1.4.1.9.9.136.1.6.5.1.5
cwr1MinConsecSvCwErrSeconds This object represents the cumulative Codeword Consecutively Severely Errored Seconds (CSES) detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwConsecutiveSevErrSecond	.1.3.6.1.4.1.9.9.136.1.6.5.1.6
cwr1MinDegradedSeconds This object represents the cumulative Codeword Degraded Seconds (DS) detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBCwrCwDegradedSecond	.1.3.6.1.4.1.9.9.136.1.6.5.1.7
cwr1MinErroredCodewords This object represents the cumulative errored codewords detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.5.1.8
cwr1MinCodewords This object represents the cumulative total received codewords detected since link power up, captured at cwr1MinUpdateTime.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.5.1.9

This table contains metrics collected over a duration of 1 second.
The data in this table is derived directly from the hardware.
          
This table will have a maximum of 60 entries providing cumulative 
status of the link, identified by ifIndex, over the past 60 seconds.
          
This table is updated once every second.

cwr1SecMetricsEntry row .1.3.6.1.4.1.9.9.136.1.6.6.1

This represents one entry in the cwr1SecMetricsTable indexed by
ifIndex and cwr1SecMetricsIndex.

The first entry in the table (cwr1SecIndex = 1) represents the
chronologically oldest data available.

Indexes

IF-MIBifIndex cwr1SecIndex

Column	Syntax	OID
cwr1SecIndex Each entry represents the sum of the metrics from the previous 1 second entry + the 1 second period immdeiately prior to the most recent update.	Integer32 Constraints: range: 1-60	.1.3.6.1.4.1.9.9.136.1.6.6.1.1
cwr1SecUpdateTime This object represents time in seconds since system power up at which time this entry was updated.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.6.6.1.2
cwr1SecRxCodewords This object represents the cumulative total number of codewords received by this radio link at the time this entry was updated.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.6.1.3
cwr1SecRSCodewordErrors This object represents the cumulative uncorrectable codewords emitted by the Reed-Solomon error correction engine at the time this entry was updated. This is also called Pre ARQ codeword error.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.6.1.4
cwr1SecArqCodewordErrors This object represents the cumulative number of uncorrectable codewords consumed by the Automatic Repeat Query error correction engine at the time this entry was updated. This is also called as Post ARQ codeword error.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.5
cwr1SecRxRrCount This represents the cumulative number of unique RR's (Retransmit Requests) received (from the remote end) at the time this entry was updated. The remote end issues a Retransmit Request if it receives an uncorrectable co…	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.6
cwr1SecRxRrEventCount This object represents the cumulative number of RRs (Retransmit Requests) that were serviced at the time this entry was updated.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.7
cwr1SecTxArqCount This object represents cumulative number of unique ARQ's that were received by the transmit side of the local end at the time this entry was updated. This provides an indication of how error free the tran…	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.8
cwr1SecTxArqEventCount This object represents cumulative number of ARQ's that were serviced at the time this entry was updated. A serviced ARQ results in a re-transmitted codeword.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.9
cwr1SecCorrectedSyncByteErrs This object represents the cumulative number of corrected sync byte errors, at the time this entry was updated.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.10
cwr1SecConsecutiveCwErrs This object represents the size of the larget block of consecutive codeword errors received since this entry was last updated.	SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.136.1.6.6.1.11
cwr1SecPostARQGoodCodewords This object represents the cumulative number of error free codewords emitted by the Automatic Repeat Query error correction engine at the time this entry was updated. Also called as Post ARQ good codewords.	CISCO-WIRELESS-TC-MIBWirelessGauge64	.1.3.6.1.4.1.9.9.136.1.6.6.1.12

This table contains information about histograms configured in
hardware. When data is collected it will be stored in histogram
bins as follows:
All values (X < cwrStartBinValue) will be kept in the first
histogram bin.
Subsequent values will be distributed in the bins based on the
cwrBinDelta. Last bin, will contain all values
(X > (cwrStartBinValue + (cwrNumBins - 2) * cwrBinDelta)),
i.e. any value that is greater than that may be stored in the
last bin.

cwrHistCtrlEntry row .1.3.6.1.4.1.9.9.136.1.7.1.1

This represents one entry in the cwrHistogramTable.
It is indexed by the ifIndex, cwrHistIndex.

Indexes

IF-MIBifIndex cwrHistIndex

Column	Syntax	OID
cwrHistIndex This object, along with ifIndex, is the index into this table and represents one entry in the table. The entry in this table for which cwrHistIndex = x is associated with the entry in cwrHistSummaryTable and the entry …	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.7.1.1.1
cwrHistClass This object represents the attribute that is being histogrammed.	CISCO-WIRELESS-TC-MIBCwrRadioSignalAttributer/w Type Values: 1 rsaIN 2 rsaINR 3 rsaConstellationVariance 4 rsaTimingOffset 5 rsaReceivedPower 6 rsaGainSettingsIF 7 rsaGainSettingsRF 8 rsaFreqOffset 9 rsaTotalGain 10 rsaSyncStatus	.1.3.6.1.4.1.9.9.136.1.7.1.1.2
cwrRfResourceId This object identifies the RF resource for which this histogram specification applies. If this is 0, the agent will automatically use the most logical value for the specified cwrHistClass. If 0 has been specified then o…	CISCO-WIRELESS-TC-MIBCwrRFZeroIndexr/w Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.7.1.1.3
cwrDspNumber This object identifies the DSP on which to create the histogram. If 0 is specified then the agent will automatically use the most logical DSP for the specified cwrHistClass parameter. If 0 has been specified then on rea…	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.9.9.136.1.7.1.1.4
cwrStartBinValue This object represents the maximum of the values that will be collected in the first bin of the histogram. All values < cwrStartBinValue will be kept in the first histogram bin.	Integer32r/w Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.9.9.136.1.7.1.1.5
cwrBinDelta This object represents the range of values of the sampled data that should be accounted for in one histogram bin. For example all data samples between x..y (where y = x + cwrBinDelta - 1), will be counted and placed in …	Powers of 2Integer32r/w Constraints: range: 2-2147483647	.1.3.6.1.4.1.9.9.136.1.7.1.1.6
cwrNumHistBins This object represents total number of bins to be created for the histogram.	Integer32r/w Constraints: range: 1-508	.1.3.6.1.4.1.9.9.136.1.7.1.1.7
cwrUpdateRate This object represents rate at which snapshots of the histogram will be available.	secondsInteger32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.7.1.1.8
cwrCollDuration This object specifies the duration for which this histogram must be accumulated. After successfully accumulating data for this amount of time the collection stops and the cwrHistStatus changes to statusCaptured.	secondsInteger32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.7.1.1.9
cwrOwnerId This object identifies management station that created this histogram specification.	RMON-MIBOwnerStringr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.9.9.136.1.7.1.1.10
cwrHistBitShift This object represents the number of bits by which the signal count is right shifted before it is stored in the histogram bin. This provides a mechanism to uniformly scale the collected histogram to account for overflow…	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.136.1.7.1.1.11
cwrHistToneSelection This object identifies which tone in a burst should be sampled for capturing the data. cwrCirculate(1): The successive tones will be used for every successive burst. cwrAverage(2): The value of every tone in a b…	Enumerationr/w Enumerated Values: 1 cwrCirculate 2 cwrAverage 3 cwrSpecific	.1.3.6.1.4.1.9.9.136.1.7.1.1.12
cwrHistToneValue If cwrHistToneSelection is cwrSpecificTone then this object identifies tone that should be used for sampling.	Integer32r/w Constraints: range: 0-216	.1.3.6.1.4.1.9.9.136.1.7.1.1.13
cwrHistAction This object represents the action to be carried out on this histogram specification. If a histogram has been successfully captured then it must be cleared before an other capture may be initiated.	CISCO-WIRELESS-TC-MIBCwrCollectionActionr/w Type Values: 1 actionStop 2 actionStart 3 actionClear 4 actionRestart	.1.3.6.1.4.1.9.9.136.1.7.1.1.14
cwrHistStatus This object represents the current state of this histogram collection. Once the histogram collection is complete the status changes statusCaptured and the data is available for use. None of the parameters of a histogra…	CISCO-WIRELESS-TC-MIBCwrCollectionStatus Type Values: 1 statusIdle 2 statusInProgress 3 statusStopped 4 statusCaptured	.1.3.6.1.4.1.9.9.136.1.7.1.1.15
cwrHistRowStatus This object may be used to create or delete a histogram control specification.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.136.1.7.1.1.16
cwrHistPeriodicSum The histogram data is updated every cwrUpdateRate seconds. When this object is set to true(1), the latest histogram data set is summed with the previous histogram data set and the cwrHistSummaryTable will reflect cumu…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.136.1.7.1.1.17

This table contains histogram Summary collected based on the
specifications in the cwrHistCtrlTable.

cwrHistSummaryEntry row .1.3.6.1.4.1.9.9.136.1.7.2.1

This represents one entry in the cwrHistSummaryTable.
It is indexed by the ifIndex and cwrHistIndex.

Indexes

IF-MIBifIndex cwrHistIndex

Column	Syntax	OID
cwrHistUpdateTime This object represents the time in seconds since power up when this histogram snapshot was retrieved from the hardware.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.7.2.1.1
cwrHistMin This object represents the minimum value of the data sample seen for this histogram.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.7.2.1.2
cwrHistMax This object represents the maximum value of the data sample seen for this histogram.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.7.2.1.3
cwrHistMean This object represents the arithemetic mean of the data sample values for this histogram.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.7.2.1.4

This table contains histogram values collected based on the
specifications in the cwrHistCtrlTable.

cwrHistDataEntry row .1.3.6.1.4.1.9.9.136.1.7.3.1

This represents one entry in the cwrHistDataTable. It is
indexed by the ifIndex and cwrHistIndex and cwrHistBinIndex.

Indexes

IF-MIBifIndex cwrHistIndex cwrHistBinIndex

Column	Syntax	OID
cwrHistBinIndex This object represents the histogram bin number for the value in cwrValue.	Integer32 Constraints: range: 1-508	.1.3.6.1.4.1.9.9.136.1.7.3.1.1
cwrValue This object represents the value in the histogram bin cwrHistBinIndex.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.136.1.7.3.1.2

This table provides facilities to establish thresholds for the 
radio signals analyzed on the radio interface. A threshold 
identified in this table may be used to trigger a timeline 
capture in the cwrTlTable.

cwrThresholdEntry row .1.3.6.1.4.1.9.9.136.1.8.1.1

This represents one entry in the cwrThresholdTable.

Indexes

IF-MIBifIndex cwrThreshIndex

Column	Syntax	OID
cwrThreshIndex This object, along with ifIndex, identifies this entry.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.1.1.1
cwrThreshAttribute This represents the attribute of a radio link which needs to be thresholded. For each of these attributes, the cwrThreshType identifies the type of change to monitor. When that threshold is exceeded a Trap with approp…	CISCO-WIRELESS-TC-MIBCwrRadioSignalAttributer/w Type Values: 1 rsaIN 2 rsaINR 3 rsaConstellationVariance 4 rsaTimingOffset 5 rsaReceivedPower 6 rsaGainSettingsIF 7 rsaGainSettingsRF 8 rsaFreqOffset 9 rsaTotalGain 10 rsaSyncStatus	.1.3.6.1.4.1.9.9.136.1.8.1.1.2
cwrThreshType This object represents the kind of change that needs to be monitored for the cwrThreshAttribute. An event is generated when the following condition is met.	CISCO-WIRELESS-TC-MIBCwrThreshLimitTyper/w Type Values: 1 upChange 2 downChange 3 highThresh 4 lowThresh 5 upLimit 6 lowLimit	.1.3.6.1.4.1.9.9.136.1.8.1.1.3
cwrThreshAntId This object identifies the RF resource for which this threshold should be defined.	CISCO-WIRELESS-TC-MIBCwrRFZeroIndexr/w Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.8.1.1.4
cwrThreshValue This object represents the value to be compared against. The cwrThreshType determines the way in which it is used. It is used as follows: if cwrThreshType is .. highThresh : Notify if data sample exceeds the cwrThreshVa…	Integer32r/w Constraints: range: -2147483647-2147483647	.1.3.6.1.4.1.9.9.136.1.8.1.1.5
cwrThreshHysteresisTime When radio signals oscillate around threshold values, they potentially flood the system with notifications. This object specifies the amount of time to wait before sending an identical notification if the oscillation…	SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.136.1.8.1.1.6
cwrThreshLimitTime This object specifies the amount of time for which the radio signal should stabilize before a trap is sent to indicate that the radio signal has stabilized.	SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.9.9.136.1.8.1.1.7
cwrThreshDspNum This object indicates the DSP used to monitor this threshold.	Integer32r/w Constraints: range: 1-8	.1.3.6.1.4.1.9.9.136.1.8.1.1.8
cwrThreshRowStatus This object represents the status of this threshold entry. It may be used to create a new threshold specification. For every cwrThreshAttrClass one threshold of cwrThreshType on one DSP may be created.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.136.1.8.1.1.9

This table contains information about timelines configured in
hardware. The number of data values captured for each timeline
is configured by setting the variable cwrTlNumDataValues. 
The captured data values can be retreived by reading the 
cwrTlDataTable.

cwrTlCtrlEntry row .1.3.6.1.4.1.9.9.136.1.8.2.1

This represents one entry in the cwrTlCtrlTable.
It is indexed by the ifIndex, cwrTlClass, cwrRfResourceId,
cwrTlDspNum.

Indexes

IF-MIBifIndex cwrTlIndex

Column	Syntax	OID
cwrTlIndex This object, along with ifIndex, is the index into this table and represents one entry in the table. The entry in this table for which cwrTlIndex = x is associated with the entry in cwrTlSummaryTable and the entry in c…	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.2.1.1
cwrTlClass This object represents the attribute for which a timline capture is requested. When a timeline is requested, cwrTlNumDataValues worth of data will be captured.	CISCO-WIRELESS-TC-MIBCwrRadioSignalAttributer/w Type Values: 1 rsaIN 2 rsaINR 3 rsaConstellationVariance 4 rsaTimingOffset 5 rsaReceivedPower 6 rsaGainSettingsIF 7 rsaGainSettingsRF 8 rsaFreqOffset 9 rsaTotalGain 10 rsaSyncStatus	.1.3.6.1.4.1.9.9.136.1.8.2.1.2
cwrTlRfResourceId This object identifies the RF resource for which this timeline specification applies. If this is 0 then the agent will automatically the most logical value for the specified cwrHistClass. If 0 has been specified then o…	CISCO-WIRELESS-TC-MIBCwrRFZeroIndexr/w Type Constraints: range: 0..2	.1.3.6.1.4.1.9.9.136.1.8.2.1.3
cwrTlDspNum This object identifies the DSP on which this timeline needs to be captures. If 0 is specified then the agent will automatically use the most logical DSP for the specified cwrTlClass parameter. If 0 has been specified on…	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.9.9.136.1.8.2.1.4
cwrTlNumDataValues This object indicates the number of data values to be captured for this timeline. The captured data can be viewed by reading the cwrTlDataTable.	number of data valuesInteger32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.2.1.5
cwrTlDecimationFactor This object represents the number of successive data samples to be added and returned. This enables larger data sets to be captured even with limited cwrTlNumDataValues.	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.136.1.8.2.1.6
cwrTlPreSumShift This object represents the number of bits by which the raw data data should be right shifted before applying cwrTlDecimationFactor. This provides a mechanims of controlling overflow due to summation.	Integer32r/w Constraints: range: 0-32	.1.3.6.1.4.1.9.9.136.1.8.2.1.7
cwrTlToneSelection This object identifies which tone in a burst should be used to sample data for the timeline. cwrCirculate(1): The successive tone will be used for every successive burst. cwrAverage(2): The value of every tone …	Enumerationr/w Enumerated Values: 1 cwrCirculate 2 cwrAverage 3 cwrSpecific	.1.3.6.1.4.1.9.9.136.1.8.2.1.8
cwrTlToneValue If cwrTlToneSelection is cwrSpecificTone then this object identifies the tone that should be used for sampling.	Integer32r/w Constraints: range: 0-216	.1.3.6.1.4.1.9.9.136.1.8.2.1.9
cwrTlThreshIndex This object specifies the index of the threshold that when triggered will start the data capture for this timeline. For a timeline data capture to be triggered by a threshold, the threshold must be defin…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.136.1.8.2.1.10
cwrTlAction This object represents the action to be carried out on this timeline specification. If a timeline has been successfully captured then it must be cleared before an other capture may be initiated.	CISCO-WIRELESS-TC-MIBCwrCollectionActionr/w Type Values: 1 actionStop 2 actionStart 3 actionClear 4 actionRestart	.1.3.6.1.4.1.9.9.136.1.8.2.1.11
cwrTlStatus This object represents the current state of this timeline collection. Once the timeline collection is complete the status changes statusCaptured and the data is available for use. None of the parameters of a timeline s…	CISCO-WIRELESS-TC-MIBCwrCollectionStatus Type Values: 1 statusIdle 2 statusInProgress 3 statusStopped 4 statusCaptured	.1.3.6.1.4.1.9.9.136.1.8.2.1.12
cwrTlPostTrigBufMgmt Once a trigger fires, this object determines which portion of the collected data to capture for use. If it is: preTrigger(1) : Then most of the data collected prior to trigger is captured. postTrigger(2): Then m…	Enumerationr/w Enumerated Values: 1 preTrigger 2 postTrigger	.1.3.6.1.4.1.9.9.136.1.8.2.1.13
cwrTlRowStatus This object may be used to create or delete a timeline control specification. Once created data sampling starts based on the value of cwrTlAction. The data capture depends on the value of cwrTlThreshInde…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.136.1.8.2.1.14

This table contains Timeline Summary collected based on the
specifications in the cwrTlCtrlTable.

cwrTlSummaryEntry row .1.3.6.1.4.1.9.9.136.1.8.3.1

This represents one entry in the cwrTlSummaryTable.
It is indexed by the ifIndex and cwrTlIndex.

Indexes

IF-MIBifIndex cwrTlIndex

Column	Syntax	OID
cwrTlUpdateTime This object represents the time in seconds since power up when this timeline capture was completed.	secondsInteger32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.3.1.1
cwrTlNumValues This object represents the number of values available in the timeline.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.136.1.8.3.1.2
cwrTlTriggerLoc This object contains the value of cwrTlValueIndex which represents the entry in the cwrTlDataTable that caused the stop trigger to fire, thereby resulting in this timeline to be collected.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.3.1.3

This table contains data values collected for the timelines
specified in the cwrTlCtrlTable.  The number of data values 
displayed for each timeline is determined by the value specified
for cwrTlNumDataValues in cwrTlCtrlTable.

cwrTlDataEntry row .1.3.6.1.4.1.9.9.136.1.8.4.1

This represents one entry in the cwrTlDataTable. It is indexed by
ifIndex, cwrTlIndex, and cwrTlValueIndex.

Indexes

IF-MIBifIndex cwrTlIndex cwrTlValueIndex

Column	Syntax	OID
cwrTlValueIndex This object, along with ifIndex and cwrTlIndex, is the index into the timeline data table.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.8.4.1.1
cwrTlValue This object represents the radio signal data sampled.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.8.4.1.2

This table contains information about the snapshots configured in
hardware. When data is collected it will be stored in
cwrSnapDataTable.

cwrSnapshotCtrlEntry row .1.3.6.1.4.1.9.9.136.1.9.1.1

This represents one entry in the cwrSnapshotCtrlTable
It is indexed by the ifIndex and cwrSnapshotDspNum.

Indexes

IF-MIBifIndex cwrSnapshotDspNum

Column	Syntax	OID
cwrSnapshotDspNum This object represents the DSP at which the snapshot needs to be collected.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.9.9.136.1.9.1.1.1
cwrSnapshotType This object represents the attribute that is being snapshoted by the hardware. When a snapshot request is issued up to 4 simultaneous radio signal attribute may be captured at once. The 4 attributes are specified by bi…	Integer32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.9.1.1.2
cwrSnapshotAction This object represents the action to be carried out on this snapshot specification. If a snapshot has been successfully captured then it must be cleared before an other capture may be initiated.	CISCO-WIRELESS-TC-MIBCwrCollectionActionr/w Type Values: 1 actionStop 2 actionStart 3 actionClear 4 actionRestart	.1.3.6.1.4.1.9.9.136.1.9.1.1.3
cwrSnapshotStatus This object represents the current status of this snapshot specification. When the status in statusInProgress none of the snapshot parameters can be configured. When the status is statusCaptured then data is available …	CISCO-WIRELESS-TC-MIBCwrCollectionStatus Type Values: 1 statusIdle 2 statusInProgress 3 statusStopped 4 statusCaptured	.1.3.6.1.4.1.9.9.136.1.9.1.1.4
cwrSnapshotRowStatus This object may be used to create or delete this snapshot specification.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.136.1.9.1.1.5

This table contains summary information for captured snapshots
defined in cwrSnapshotCtrlTable.

cwrSnapSummaryEntry row .1.3.6.1.4.1.9.9.136.1.9.2.1

This represents one entry in the cwrSnapSummaryTable. It is indexed
by the ifIndex and cwrSnapDspNum.

Indexes

IF-MIBifIndex cwrSnapshotDspNum

Column	Syntax	OID
cwrSnapAttr1Id This object represents the first snapshot attribute value.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.9.2.1.2
cwrSnapAttr1Size This object represents the number of values captured for the snapshot cwrSnapAttr1Id.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.9.9.136.1.9.2.1.3
cwrSnapAttr2Id This object represents the second snapshot attribute value.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.9.2.1.4
cwrSnapAttr2Size This object represents the number of values captured for the snapshot cwrSnapAttr2Id.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.9.9.136.1.9.2.1.5
cwrSnapAttr3Id This object represents the third snapshot attribute value.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.9.2.1.6
cwrSnapAttr3Size This object represents the number of values captured for the snapshot cwrSnapAttr3Id.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.9.9.136.1.9.2.1.7
cwrSnapAttr4Id This object represents the third snapshot attribute value.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.136.1.9.2.1.8
cwrSnapAttr4Size This object represents the number of values captured for the snapshot cwrSnapAttr4Id.	Integer32 Constraints: range: 0-4096	.1.3.6.1.4.1.9.9.136.1.9.2.1.9

This table contains snapshot values collected based on the
specifications in the cwrSnapshotCtrlTable.

cwrSnapDataEntry row .1.3.6.1.4.1.9.9.136.1.9.3.1

This represents one entry in the cwrSnapDataTable. It is indexed
by the ifIndex and cwrSnapValueIndex.

The values in this table represent real numbers or complex numbers.
If they are real numbers then cwr…

Indexes

IF-MIBifIndex cwrSnapshotDspNum cwrSnapValueIndex

Column	Syntax	OID
cwrSnapValueIndex This object represents the snapshot entry index number.	Integer32 Constraints: range: 1-4096	.1.3.6.1.4.1.9.9.136.1.9.3.1.1
cwrRealPart The data sample value. Real part.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.9.3.1.2
cwrImaginaryPart The data sample value. Imaginary part if the attribute is represented by a complex number.	Integer32 Constraints: range: -2147483648-2147483647	.1.3.6.1.4.1.9.9.136.1.9.3.1.3

This table contains information about the antenns available for
use.

cwrAntennaEntry row .1.3.6.1.4.1.9.9.136.1.10.1.1

This represents one entry in the cwrAntennaTable. This table
provides details on the antennas available for use on the local
system. It is indexed by cwrAntennaIndex.

Indexes

cwrAntennaIndex

Column	Syntax	OID
cwrAntennaIndex This object represents the index of this entry in the cwrAntennaTable.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.9.9.136.1.10.1.1.1
cwrAntennaXDim This object represents the dimension of the antenna in the X direction.	InchesInteger32r/w Constraints: range: 1-96	.1.3.6.1.4.1.9.9.136.1.10.1.1.2
cwrAntennaYDim This object represents the dimension of the antenna in the Y direction.	InchesInteger32r/w Constraints: range: 1-96	.1.3.6.1.4.1.9.9.136.1.10.1.1.3
cwrAntennaType This object represents antenna type for example 'dish-antenna'.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.9.9.136.1.10.1.1.4
cwrAntennaDescr This object describes the antenna.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.9.9.136.1.10.1.1.5
cwrAntennaGain This object represents the gain of this antenna.	dBi : decibel IsotropicInteger32r/w Constraints: range: 0-60	.1.3.6.1.4.1.9.9.136.1.10.1.1.6
cwrAntennaPolarization This object represents the electrirc polarization of the antanna.	Enumerationr/w Enumerated Values: 1 vertical 2 horizontal	.1.3.6.1.4.1.9.9.136.1.10.1.1.7

This table provides information about the last trap that was
generated on this interface.

cwrRadioTrapEntry row .1.3.6.1.4.1.9.9.136.2.1.1.1

This represents one entry in this table.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cwrTrapReason The explanation string for the event trap cwrEventId.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.9.9.136.2.1.1.1.1