CISCO-FC-ROUTE-MIB Table View

The local system's Fibre Channel Routing table.
This table lists all the routes that is configured/
calculated at the local system.
Traffic through the TL-Port (translation port) uses the
R-CTL field in the FC protocol header. During forwarding,
this R-CTL field is part of the the value looked-up in
the route table for matching.
The value of the object fcRoutePreference is used to
select one route over other when more than one route to
the same destination is learned from different protocols,
peers, or static routes from end-users.
Only the entries configured by the user, which are 
fcRouteProto of type netmgmt(3), can be deleted by the
user.

fcRouteEntry row .1.3.6.1.4.1.9.9.284.1.1.10.1

Each entry contains a route to a particular destination
in a particular VSAN via a particular output interface,
and learned in a particular manner.

Indexes

CISCO-VSAN-MIBvsanIndex fcRouteDestAddrId fcRouteDestMask fcRouteProto fcRouteInterface

Column	Syntax	OID
fcRouteDestAddrId The destination FC-ID of this route.	CISCO-ST-TCFcAddressId Type Constraints: range: 3	.1.3.6.1.4.1.9.9.284.1.1.10.1.1
fcRouteDestMask Indicate the mask to be logical-ANDed with the destination address Id before being compared to the value in the fcRouteDestAddrId field. This can only be 255.255.255 or 255.255.0 or 255.0.0 .	CISCO-ST-TCFcAddressId Type Constraints: range: 3	.1.3.6.1.4.1.9.9.284.1.1.10.1.2
fcRouteProto The routing mechanism via which this route was learned. other(1) - not specified local(2) - local interface netmgmt(3)- static route The following are all dynamic routing protocols fspf(4…	Enumeration Enumerated Values: 1 other 2 local 3 netmgmt 4 fspf 5 mpls 6 multicast	.1.3.6.1.4.1.9.9.284.1.1.10.1.3
fcRouteInterface The ifIndex value, which identifies the local interface through which the next hop of this route should be reached. If the interface type is TL-Port then R-CTL field in the FC protocol header is also used for look-up…	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.284.1.1.10.1.4
fcRouteDomainId The domain ID of next hop switch. However this object, when read, could have a value zero if value of fcRouteProto is 'local'.	Unsigned32r/w Constraints: range: 0-239	.1.3.6.1.4.1.9.9.284.1.1.10.1.5
fcRouteMetric The routing metric for this route. The use of this object is dependent on fcRouteProto used.	Unsigned32r/w Constraints: range: 0-65536	.1.3.6.1.4.1.9.9.284.1.1.10.1.6
fcRouteType The type of route. local(1): refers to a route for which the next hop is the final destination; remote(2): refers to a route for which the next hop is not the final destination. This object is not…	Enumerationr/w Enumerated Values: 1 local 2 remote	.1.3.6.1.4.1.9.9.284.1.1.10.1.7
fcRoutePermanent The value if true(1), indicates the route is not to be removed from the relevant Forwarding information base even if the port is operationally 'down'. If false(2), the route is removed from the relevant Forwarding inf…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.284.1.1.10.1.8
fcRouteRowStatus The status of this conceptual row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.284.1.1.10.1.9

The table to configure and show the ingress traffic 
counters on physical components (e.g., Linecards).
The user has the option of configuring counters 
depending on the bits selected for the object 
fcRouteFlowType.  If the user selects only vsanId(0)
bit for all the entries, then no more than 1024 entries
can be created. If the user selects all the 4 bits,
vsanId(0), destId(1), srcId(2), port(3), for some 
entries, then additional entries can be created, up to
a maximum of 2048 entries.
For statistics collection R-CTL is not part of the 
the value looked-up in the route table, so the counters
are updated immaterial of R-CTL field.

fcRouteFlowStatEntry row .1.3.6.1.4.1.9.9.284.1.2.1.1

Each entry provides information on the ingress traffic
counters at the physical component indicated by
entPhysicalIndex. Entries can only be created for
physical components, e.g.,line cards, which support
this type …

Indexes

ENTITY-MIBentPhysicalIndex fcRouteFlowIndex

Column	Syntax	OID
fcRouteFlowIndex The index of this entry.	Unsigned32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.9.9.284.1.2.1.1.1
fcRouteFlowType The matching criteria by which flows are selected to be included in the traffic which is instrumented by the ingress traffic counters. For each bit which is set, the corresponding object must be configured by the netwo…	Bitsr/w Enumerated Values: 0 vsanId 1 destId 2 srcId 3 port	.1.3.6.1.4.1.9.9.284.1.2.1.1.2
fcRouteFlowVsanId The id of VSAN. This object cannot be modified while the corresponding value of fcRouteFlowRowStatus is equal to 'active'.	Integer32r/w Constraints: range: 1-4093	.1.3.6.1.4.1.9.9.284.1.2.1.1.3
fcRouteFlowDestId The destination fibre channel address id. This object cannot be modified while the corresponding value of fcRouteFlowRowStatus is equal to 'active'.	CISCO-ST-TCFcAddressIdr/w Type Constraints: range: 3	.1.3.6.1.4.1.9.9.284.1.2.1.1.4
fcRouteFlowSrcId The source fibre channel address id. This object cannot be modified while the corresponding value of fcRouteFlowRowStatus is equal to 'active'.	CISCO-ST-TCFcAddressIdr/w Type Constraints: range: 3	.1.3.6.1.4.1.9.9.284.1.2.1.1.5
fcRouteFlowMask The mask for source and destination fibre channel address id. This object cannot be modified while the corresponding value of fcRouteFlowRowStatus is equal to 'active'.	CISCO-ST-TCFcAddressIdr/w Type Constraints: range: 3	.1.3.6.1.4.1.9.9.284.1.2.1.1.6
fcRouteFlowPort The physical ingress port to which this counter applies. This object cannot be modified while the corresponding value of fcRouteFlowRowStatus is equal to 'active'.	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.9.9.284.1.2.1.1.7
fcRouteFlowFrames The number of received frames for the flow created by the network manager.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.284.1.2.1.1.8
fcRouteFlowBytes The number of received frame bytes for the flow created by the network manager.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.9.9.284.1.2.1.1.9
fcRouteFlowCreationTime The timestamp indicating the time the row was created or modified.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.9.9.284.1.2.1.1.11
fcRouteFlowRowStatus The status of this conceptual row.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.9.9.284.1.2.1.1.12