CISCO-ALPS-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
12
Rows
12
Columns
153
.1.3.6.1.4.1.9.9.95.1.2.2
·
1 row entry
·
18 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsRemPeerTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsRemPeerTable'
A list of Remote peers that the local ALPS peer can communicate with.
Each entry represents an Remote ALPS Peer.
Indexes
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
alpsRemPeerIpAddrdeprecated The remote IP address for the TCP Connection. | SNMPv2-SMIIpAddress Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.2.2.1.1 | ||||||||||||
alpsRemPeerConnTypedeprecated Type of ALPS circuit established. Dynamic circuits areestablished only when there is data traffic that needs to be sent across and are closed when the alpsRemPeerIdleTimer expires. Permanent circuits stay up regardle… | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.2.1.2 | ||||||||||||
alpsRemPeerLocalPortdeprecated The port number used locally by the tcp connection for thecircuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number applicable to t… | Integer32 Constraints: range: 0-65535 | .1.3.6.1.4.1.9.9.95.1.2.2.1.3 | ||||||||||||
alpsRemPeerRemotePortdeprecated The port number used by the remote end of the tcp connectionfor the circuit. the initiator of a connection will dynamically assign a port number. the other end of the connection will have a well-known port number appli… | Integer32 Constraints: range: 0-65535 | .1.3.6.1.4.1.9.9.95.1.2.2.1.4 | ||||||||||||
alpsRemPeerStatedeprecated TCP Peer State. Initially the connection is in the closed state.For permanent connections, it starts opening the TCP connection immediately, but for dynamic ones, it waits till there is traffic addressed to the remote … | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.2.1.5 | ||||||||||||
alpsRemPeerUptimedeprecated Time elapsed since TCP connection was established. | SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.6 | ||||||||||||
alpsRemPeerNumActiveCktsdeprecated Number of active ALPS circuits in this TCP session. | SNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.7 | ||||||||||||
alpsRemPeerIdleTimerdeprecated The TCP session with the peer will be closed if there is noactivity for alpsInactiveTimer seconds. This is valid only for dynamic circuits | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.2.1.8 | ||||||||||||
alpsRemPeerAlarmsEnableddeprecated Specifies whether alarms are generated for this remote Peer | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.2.2.1.9 | ||||||||||||
alpsRemPeerTCPQlendeprecated Maximum TCP Queue size allowed for this TCP session. | packetsInteger32r/w Constraints: range: 1-200 | .1.3.6.1.4.1.9.9.95.1.2.2.1.10 | ||||||||||||
alpsRemPeerOutPacketsdeprecated Number of packets transmitted to the remote peer. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.11 | ||||||||||||
alpsRemPeerOutOctetsdeprecated Number of octets transmitted to the remote peer. | octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.12 | ||||||||||||
alpsRemPeerInPacketsdeprecated Number of packets received from the remote peer. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.13 | ||||||||||||
alpsRemPeerInOctetsdeprecated Number of octets received from the remote peer. | octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.14 | ||||||||||||
alpsRemPeerDropsGiantdeprecated Number of Packets dropped because they were larger than themaximum allowed packet size of 3840 bytes. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.15 | ||||||||||||
alpsRemPeerDropsQFulldeprecated Number of packets dropped because the TCP queue (ofsize alpsRemPeerTCPQlen) was full. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.16 | ||||||||||||
alpsRemPeerDropsPeerUnreachdeprecated Number of packets dropped because remote peer was unreachable. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.2.1.17 | ||||||||||||
alpsRemPeerRowStatusdeprecated This object is used to create a new row or modify ordelete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.2.2.1.18 |
alpsRemPeerCfgTable
table.1.3.6.1.4.1.9.9.95.1.2.3
·
1 row entry
·
10 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsRemPeerCfgTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsRemPeerCfgTable'
Table listing of all administered ALPS remote peer configuration entries on this node. Entries in this table can be created via a CLI command or via alpsRemPeerCfgRowStatus.
Each entry represents an ALPS remote peer
configuration entry on this node.
configuration entry on this node.
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsRemPeerCfgIpAddrThe configured IP address of an ALPS remote peer. | SNMPv2-SMIIpAddress Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.2.3.1.1 | ||||||||||||
| alpsRemPeerCfgProtocolThe configured ALPS protocol encapsulation. This protocol encapsulation is at the layer above TCP. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.3.1.2 | ||||||||||||
| alpsRemPeerCfgActivationThe configured type of ALPS peer activation. | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.3.1.3 | ||||||||||||
| alpsRemPeerCfgTCPQLenThe configured maximum TCP Queue size. | packetsInteger32r/w Constraints: range: 1-100 | .1.3.6.1.4.1.9.9.95.1.2.3.1.4 | ||||||||||||
| alpsRemPeerCfgIdleTimerThe configured idle timer for a dynamic activation peer. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.3.1.5 | ||||||||||||
| alpsRemPeerCfgNoCircTimerThe configured no-circuit timer for a dynamic activation peer. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.3.1.6 | ||||||||||||
| alpsRemPeerCfgAlarmsOnThe configured parameter which specifies whether alarms are generated for remote peer connections to the IP address in alpsRemPeerCfgIpAddr. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.2.3.1.7 | ||||||||||||
| alpsRemPeerCfgStatIntvlThe configured status interval timer. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.3.1.8 | ||||||||||||
| alpsRemPeerCfgStatRetryThe configured number of status retries. | Integer32r/w Constraints: range: 0-100 | .1.3.6.1.4.1.9.9.95.1.2.3.1.9 | ||||||||||||
| alpsRemPeerCfgRowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.2.3.1.10 |
alpsRemPeerConnTable
table.1.3.6.1.4.1.9.9.95.1.2.4
·
1 row entry
·
27 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsRemPeerConnTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsRemPeerConnTable'
Table listing of all ALPS remote peer connections on this node.
Each entry represents an ALPS remote peer
connection on this node.
connection on this node.
| Column | Syntax | OID | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsRemPeerConnIpAddrThe IP address of the ALPS remote peer. | SNMPv2-SMIIpAddress Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.2.4.1.1 | ||||||||||||||||
| alpsRemPeerConnIdStringA descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address. | OctetString Constraints: range: 1-20 | .1.3.6.1.4.1.9.9.95.1.2.4.1.2 | ||||||||||||||||
| alpsRemPeerConnLocalPortThe local TCP port number used by the underlying TCP connection to an ALPS remote peer. | Integer32 Constraints: range: 0-65535 | .1.3.6.1.4.1.9.9.95.1.2.4.1.3 | ||||||||||||||||
| alpsRemPeerConnForeignPortThe foreign (remote) TCP port number used by the underlying TCP connection to an ALPS remote peer. | Integer32 Constraints: range: 0-65535 | .1.3.6.1.4.1.9.9.95.1.2.4.1.4 | ||||||||||||||||
| alpsRemPeerConnStateThe state of the connection to an ALPS remote peer. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.4.1.5 | ||||||||||||||||
| alpsRemPeerConnProtocolThe ALPS protocol encapsulation used on the connection to the ALPS remote peer. This protocol encapsulation is a layer above TCP. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.4.1.6 | ||||||||||||||||
| alpsRemPeerConnCreationThe stimulus for creating the peer connection object. The peer connection object may be created solely due to configuration (admin) or due to a combination of configuration and protocol events (learned). | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.4.1.7 | ||||||||||||||||
| alpsRemPeerConnActivationBasis for activation a peer connection. A permanent activation peer connection will attempt to open immediately and stay open, regardless of the usage of the peer connection. A dynamic activation peer connection only… | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.4.1.8 | ||||||||||||||||
| alpsRemPeerConnUptimeElapsed time since the ALPS peer connection was successfully established. | SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.9 | ||||||||||||||||
| alpsRemPeerConnNumActCircThe number of ALPS virtual circuits using the connection to this ALPS remote peer. | Integer32 Constraints: range: 0-65535 | .1.3.6.1.4.1.9.9.95.1.2.4.1.10 | ||||||||||||||||
| alpsRemPeerConnLastTxRxThe value of sysUpTime when a peer data message was last transmitted or received across this ALPS remote peer connection. This timestamp is not update if the peer message is a peer status inquiry/response message. | SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t… | .1.3.6.1.4.1.9.9.95.1.2.4.1.11 | ||||||||||||||||
| alpsRemPeerConnLastRxAnyThe value of sysUpTime when a peer data or status message is last received across the ALPS remote peer connection. | SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t… | .1.3.6.1.4.1.9.9.95.1.2.4.1.12 | ||||||||||||||||
| alpsRemPeerConnIdleTimerA dynamic activation ALPS peer connection will be closed if zero peer data messages are sent or received for a length of time greater than or equal to this timer. | SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.4.1.13 | ||||||||||||||||
| alpsRemPeerConnNoCircTimerA dynamic activation ALPS peer connection will be closed if zero ALPS circuits are active or attempt to activate for a length of time greater than or equal to this timer. | SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.2.4.1.14 | ||||||||||||||||
| alpsRemPeerConnTCPQLenThe maximum number of ALPS peer messages that can be queued in a single TCP session. | Integer32 Constraints: range: 1-100 | .1.3.6.1.4.1.9.9.95.1.2.4.1.15 | ||||||||||||||||
| alpsRemPeerConnAlarmsOnThis parameter specifies whether ALPS alarms are generated for this ALPS remote peer connection. | SNMPv2-TCTruthValue Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.2.4.1.16 | ||||||||||||||||
| alpsRemPeerConnStatIntvlThe time interval (in seconds) between transmission of consecutive ALPS Peer Status messages. These messages are only transmitted if zero messages are received on the peer connection for a length of time greater than… | Integer32 Constraints: range: 0-300 | .1.3.6.1.4.1.9.9.95.1.2.4.1.17 | ||||||||||||||||
| alpsRemPeerConnStatRetryThe number of consecutive unanswered ALPS Peer Status messages transmitted before closing the conenction to the ALPS remote peer. | Integer32 Constraints: range: 0-100 | .1.3.6.1.4.1.9.9.95.1.2.4.1.18 | ||||||||||||||||
| alpsRemPeerConnDownReasonReason that an ALPS Peer connection failed to open sauccessfully. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.2.4.1.19 | ||||||||||||||||
| alpsRemPeerConnOutPacketsNumber of packets transmitted on this ALPS remote peer connection. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.20 | ||||||||||||||||
| alpsRemPeerConnOutOctetsNumber of octets transmitted on this ALPS remote peer connection. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.21 | ||||||||||||||||
| alpsRemPeerConnInPacketsNumber of packets received on this ALPS remote peer connection. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.22 | ||||||||||||||||
| alpsRemPeerConnInOctetsNumber of octets received on this ALPS remote peer connection. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.23 | ||||||||||||||||
| alpsRemPeerConnDropsGiantNumber of ALPS peer packets dropped due to exceeding the maximum allowed packet size of 3840 bytes. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.24 | ||||||||||||||||
| alpsRemPeerConnDropsQFullNumber of ALPS peer packets dropped because the TCP output queue is full. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.25 | ||||||||||||||||
| alpsRemPeerConnDropsUnreachNumber of ALPS peer packets dropped because the ALPS remote peer is unreachable. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.26 | ||||||||||||||||
| alpsRemPeerConnDropsVersionNumber of ALPS peer packets dropped because of a version mismatch in the ALPS encapsulation. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.2.4.1.27 |
alpsCktBaseTable
table.1.3.6.1.4.1.9.9.95.1.3.1
·
1 row entry
·
24 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsCktBaseTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsCktBaseTable'
A list of ALPS circuits. This table contains variables common to central & remote routers.
Details of ALPS Circuits.
Indexes
| Column | Syntax | OID | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsCktBaseNameSpecifies the ALPS Circuit Name. This is unique within the network. | AlpsCktName Type Constraints: range: 1..12 | .1.3.6.1.4.1.9.9.95.1.3.1.1.1 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseDlcTypeSpecifies what type of circuit this is. The X25 circuit is set up with the same name as the P1024 circuit so we need this variable to distinguish between the two, in case local switching is done. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.1.1.2 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBasePriPeerAddrThis is the IP address of the Primary Central peer. It is mandatory to configure a primary peer, but the backup peer is optional. | SNMPv2-SMIIpAddressr/w Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.3.1.1.3 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseAlarmsEnabledSpecifies whether alarms are generated for this ALPS circuit. Alarms can be syslog messages or SNMP traps - both are controlled using the same flags. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.3.1.1.4 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseConnTypeSpecifies the ALPS Circuit Connection Type. | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.1.1.5 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseStateIndicates the state of ALPS Circuit. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.1.1.6 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseNumActiveAscusReports the number of enabled ASCUs that are attached to this ALPS Circuit. Attachment of an ASCU to an ALPS circuit may occur due to configuration or due to information passed in a protocol message. | Integer32 Constraints: range: 0-64 | .1.3.6.1.4.1.9.9.95.1.3.1.1.7 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseCurrentPeerReports the IP address of the peer that this ALPS circuit is currently connected to. | SNMPv2-SMIIpAddress Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.3.1.1.8 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseLifeTimeTimerA data message that has been queued within the router for longer than this interval will be dropped. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.3.1.1.9 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseHostLinkNumberSpecifies host link number (on Central router) for this ALPS Circuit. The host link number is used to provide a degree of transparency to the remote router. A single host link may correspond to multiple physical links … | Integer32r/w Constraints: range: 1-255 | .1.3.6.1.4.1.9.9.95.1.3.1.1.10 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseHostLinkTypeSpecifies host link type(on Central router) for this ALPS Circuit. | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.1.1.11 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseRemHldSpecifies the HLD (High-level descriptor) of the AX.25/EMTOX host for this ALPS Circuit. This serves as an identifier for the host | Integer32r/w Constraints: range: 1-32639 | .1.3.6.1.4.1.9.9.95.1.3.1.1.12 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseLocalHldSpecifies the local HLD for this ALPS Circuit. HLDs are required at the host for both ends of the connection. | Integer32r/w Constraints: range: 1-32639 | .1.3.6.1.4.1.9.9.95.1.3.1.1.13 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseDownReasonReports the reason why this ALPS Circuit is down, if it is down. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.1.1.14 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseOutPacketsNumber of packets transmitted to remote peer over this circuit. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.15 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseOutOctetsNumber of octets transmitted to remote peer over this circuit. | octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.16 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseInPacketsNumber of packets received from remote peer over this circuit. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.17 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseInOctetsNumber of octets received from remote peer over this circuit. | octetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.18 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseDropsCktDisabledNumber of packets dropped because the circuit was disabled. This would typically be packets that were queueued before the circuit was disabled which are now left in the queue. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.19 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseDropsQOverflowNumber of packets dropped due to TCP Congestion. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.20 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseDropsLifeTimeExpdNumber of packets which were queued within the router for longer than alpsCktBaseLifeTimeTimer. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.1.1.21 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseEnabledThis specifies if the circuit has been enabled. After a circuit has been configured, it must be explicitly enabled in order for the circuit to be set up. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.3.1.1.22 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseRowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.3.1.1.23 | ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| alpsCktBaseCurrPeerConnIdA descriptive ASCII string that is used to distinguish among different peer connections to the same ALPS remote peer IP address. | OctetString Constraints: range: 1-20 | .1.3.6.1.4.1.9.9.95.1.3.1.1.24 |
alpsCktX25Table
table.1.3.6.1.4.1.9.9.95.1.3.2
·
1 row entry
·
6 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsCktX25Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsCktX25Table'
A list of ALPS X.25 circuits. These entries exist only for X.25 circuits. hence this table would probably be empty at the remote router
Details of ALPS Circuits.
Indexes
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
| alpsCktX25DlcTypeSpecifies what type of circuit this is. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.2.1.1 | ||||
| alpsCktX25IfIndexReports the interface the circuit is on. This is the interface which is connected to the host | IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must … | .1.3.6.1.4.1.9.9.95.1.3.2.1.2 | ||||
| alpsCktX25LCNThe Logical Channel Number being used on the X.25 VC for this ALPS Circuit. | Integer32 Constraints: range: 1-4096 | .1.3.6.1.4.1.9.9.95.1.3.2.1.3 | ||||
| alpsCktX25HostX121The X.121 address on the host side which the central router uses to connect to the host | RFC1382-MIBX121Address Type Constraints: range: 0..17 | .1.3.6.1.4.1.9.9.95.1.3.2.1.4 | ||||
| alpsCktX25RemoteX121X.121 address of the remote side. Remote here refers to the side that the ASCUS are connected to and is also referred to as the remote router. | RFC1382-MIBX121Address Type Constraints: range: 0..17 | .1.3.6.1.4.1.9.9.95.1.3.2.1.5 | ||||
| alpsCktX25DropsVcResetNumber of packets dropped due to the VC being reset. These are packets that were queued up for transmission on that VC when it was reset | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.2.1.6 |
alpsCktP1024Table
table.1.3.6.1.4.1.9.9.95.1.3.3
·
1 row entry
·
15 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsCktP1024Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsCktP1024Table'
A list of ALC or UTS Alps circuits.
Details of ALPS Circuits.
Indexes
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsCktP1024DlcTypeSpecifies what type of circuit this is. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.3.1.1 | ||||||||||||
| alpsCktP1024BackupPeerAddrThis is the IP address of the backup remote peer. This is optional and hence may not always exist. | SNMPv2-SMIIpAddressr/w Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.3.3.1.2 | ||||||||||||
| alpsCktP1024RetryTimerSpecifies the interval at which a permanent ALPS circuit will attempt to reestablish the circuit in case it wasn't able to come up. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.3.3.1.3 | ||||||||||||
| alpsCktP1024IdleTimerIf there is no traffic on a dynamic ALPS circuit for this interval, it will be cleared. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.3.3.1.4 | ||||||||||||
| alpsCktP1024EmtoxX121Specifies the X.121 address of the SVC established with EMTOX host. This field should be set to length zero in the case of PVCs (AX.25 host). | RFC1382-MIBX121Addressr/w Type Constraints: range: 0..17 | .1.3.6.1.4.1.9.9.95.1.3.3.1.5 | ||||||||||||
| alpsCktP1024Ax25LCNSpecifies the Logical Channel Number being used on the PVC established with AX.25 host. This field should be set to zero in the case of SVCs (EMTOX host). | Integer32r/w Constraints: range: 0-4096 | .1.3.6.1.4.1.9.9.95.1.3.3.1.6 | ||||||||||||
| alpsCktP1024WinOutSpecifies X.25 transmit Window size on the Logical Channel Number of this ALPS Circuit. | Integer32r/w Constraints: range: 1-7 | .1.3.6.1.4.1.9.9.95.1.3.3.1.7 | ||||||||||||
| alpsCktP1024WinInSpecifies the X.25 receive Window size on the Logical Channel Number of this ALPS Circuit. | Integer32r/w Constraints: range: 1-7 | .1.3.6.1.4.1.9.9.95.1.3.3.1.8 | ||||||||||||
| alpsCktP1024OutPktSizeSpecifies the X.25 maxiumum output Packet size on the Logical Channel Number of this ALPS Circuit. The default output Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX. | bytesInteger32r/w Constraints: range: 128-4096 | .1.3.6.1.4.1.9.9.95.1.3.3.1.9 | ||||||||||||
| alpsCktP1024InPktSizeSpecifies X.25 maximum input Packet size on the Logical Channel Number of this ALPS Circuit. The default input Packet size for AX.25 is 240 bytes and 128 bytes for EMTOX. | bytesInteger32r/w Constraints: range: 128-4096 | .1.3.6.1.4.1.9.9.95.1.3.3.1.10 | ||||||||||||
| alpsCktP1024SvcMsgListSpecifies the Service Message List Number to use on this ALPS Circuit. This allows custom service messages to be sent for ASCUs on a particular circuit. Service messages are sent out by the router to the ASCU when abno… | Integer32r/w Constraints: range: 0-8 | .1.3.6.1.4.1.9.9.95.1.3.3.1.11 | ||||||||||||
| alpsCktP1024SvcMsgIntvlSpecifies Service Message Time Interval for the Service messages to be sent this ALPS Circuit. This controls how frequently the messages are repeated when an error condition (e.g. network being down) persists. | SNMPv2-SMITimeTicksr/w Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.3.1.12 | ||||||||||||
| alpsCktP1024DropsUnkAscuNumber of packets that were found to be from an Unknown ASCU (i.e. an ASCU that had not been configured) and hence were dropped. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.3.3.1.13 | ||||||||||||
| alpsCktP1024RowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.3.3.1.14 | ||||||||||||
| alpsCktP1024MatipCloseDelaySpecifies the minumum delay between transmission of a MATIP Close and the transmission of a MATIP Session Open for this ALPS circuit. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.3.3.1.15 |
alpsCktAscuTable
table.1.3.6.1.4.1.9.9.95.1.3.4
·
1 row entry
·
7 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsCktAscuTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsCktAscuTable'
A list of ASCUs for each ALPS Circuit. This may not include all ASCUs which have this circuit configured as alpsAscuCktName because some ASCUs may be rejected by the host while setting up the circuit.
Details of ASCUs on ASCU Circuits.
| Column | Syntax | OID | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsCktAscuCktNameThe name of the ALPS circuit which this ASCU is on. The circuit may be always up (for permanent circuits) or get set up (dynamic circuits) when there is traffic on one of the ASCUs which are set up for that circuit. | AlpsCktName Type Constraints: range: 1..12 | .1.3.6.1.4.1.9.9.95.1.3.4.1.1 | ||||||||||
| alpsCktAscuCktDlcTypeSpecifies what type of circuit this is. The X.25 circuit is set up with the same name as the ALC circuit so we need this variable to distinguish between the two. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.4.1.2 | ||||||||||
| alpsCktAscuA1A1 value. This is used along with the alpsCktAscuA2 value to identify the ASCU within the circuit. | AlpsAscuA1A2Value Type Constraints: range: 0..255 | .1.3.6.1.4.1.9.9.95.1.3.4.1.3 | ||||||||||
| alpsCktAscuA2A2 value. This is used along with the alpsCktAscuA1 value to identify the ASCU within the circuit. | AlpsAscuA1A2Value Type Constraints: range: 0..255 | .1.3.6.1.4.1.9.9.95.1.3.4.1.4 | ||||||||||
| alpsCktAscuIfIndexReports the interface the ASCU is on. This field, along with alpsCktAscuId is provided so that it is possible to correlate this information with the configured ASCU information in alpsAscuTable | IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must … | .1.3.6.1.4.1.9.9.95.1.3.4.1.5 | ||||||||||
| alpsCktAscuIdReports the ASCU Identifier which uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. A value of 0 indicates that the ASCU id is ei… | Integer32 Constraints: range: 0-127 | .1.3.6.1.4.1.9.9.95.1.3.4.1.6 | ||||||||||
| alpsCktAscuStatusReports the ASCU status - ASCUs configured on the circuit can be rejected at the host and would then be marked REJECT. Also, ASCUs configured after the circuit has been established are not added dynamically to the circ… | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.3.4.1.7 |
alpsIfP1024Table
table.1.3.6.1.4.1.9.9.95.1.4.1
·
1 row entry
·
13 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsIfP1024Table
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsIfP1024Table'
A list of interfaces running the P1024B or P1024C protocols
Interface Details
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
| alpsIfP1024EncapTypeReports the encapsulation type for this Serial Interface. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.4.1.1.1 | ||||
| alpsIfP1024PollRespTimeoutSpecifies the Poll Response Time out value. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.4.1.1.2 | ||||
| alpsIfP1024GATimeoutSpecifies the time-out delay between receipt of first character of an input sequence solicited by a poll and receipt of GA sequence. | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.4.1.1.3 | ||||
| alpsIfP1024PollPauseTimeoutSpecifies the minimum delay between two poll cycles. Thus the poll pause interval is counted from the instant when the first ASCU in the poll list is polled. Note that this is the delay between two traversals of the en… | SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.4.1.1.4 | ||||
| alpsIfP1024MaxErrCntSpecifies a maximum error count for this interface. After an ASCU link comes up, if it experiences this number of errors the ASCU link will be shutdown. The default value of 0 results in the ASCU link never being shutdo… | Integer32r/w Constraints: range: 0-30 | .1.3.6.1.4.1.9.9.95.1.4.1.1.5 | ||||
| alpsIfP1024MaxRetransSpecifies the maximum number of times an output message will be retransmitted before it is discarded. This is relevant only for P1024C (UTS). For ALC, a value of 0 will be returned. Note that legal values for UTS are 1-… | Integer32r/w Constraints: range: 0-10 | .1.3.6.1.4.1.9.9.95.1.4.1.1.6 | ||||
| alpsIfP1024CurrErrCntReports the number of errors currently existing for this ASCU link. When this equals alpsIfP1024MaxErrCnt then the ASCU link will be shut down, unless alpsIfP1024MaxErrCnt equals 0 in which case the ascu link is never s… | Integer32 Constraints: range: 0-30 | .1.3.6.1.4.1.9.9.95.1.4.1.1.7 | ||||
| alpsIfP1024MinGoodPollRespSpecifies the number of good Poll Responses to be received from an ASCU before it can be declared up. | Integer32r/w Constraints: range: 1-30 | .1.3.6.1.4.1.9.9.95.1.4.1.1.8 | ||||
| alpsIfP1024PollingRatioSpecifies how many times ASCUs in UP state are polled before an ASCU in DOWN state is polled again. | Integer32r/w Constraints: range: 1-30 | .1.3.6.1.4.1.9.9.95.1.4.1.1.9 | ||||
| alpsIfP1024NumAscusReports the number of ASCUs configured on this Serial Port. | AscusSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.4.1.1.10 | ||||
| alpsIfP1024ServMsgFormatSpecifies the format of the service message sent to an ASCU on this interface. | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.4.1.1.11 | ||||
| alpsIfP1024ServMsgStatusChangeSpecifies whether service messages generated due to an ALPS circuit status change or an ASCU status change, will be forwarded to the ASCU. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.4.1.1.12 | ||||
| alpsIfP1024ServMsgDropTermAddrSpecifies whether the service message will be sent to the same terminal address of the dropped message or the configured value. | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.4.1.1.13 |
alpsIfHLinkTable
table.1.3.6.1.4.1.9.9.95.1.4.2
·
1 row entry
·
6 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsIfHLinkTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsIfHLinkTable'
A list of interfaces running AX.25/EMTOX host link protocols. These are on the central router
Details of AX.25/EMTOX host link protocols on an Interface.
| Column | Syntax | OID | ||||
|---|---|---|---|---|---|---|
| alpsIfHLinkHostHldSpecifies the HLD of the AX.25/EMTOX host connected on this Interface. The HLD(High-level descriptor) serves as an identifier along with the hostlink number and helps correlate the ALPS circuit to a host link. The hex … | Integer32 Constraints: range: 1-65535 | .1.3.6.1.4.1.9.9.95.1.4.2.1.1 | ||||
| alpsIfHLinkNumberSpecifies the configured Host Link Number on this Serial Interface. | Integer32 Constraints: range: 1-255 | .1.3.6.1.4.1.9.9.95.1.4.2.1.2 | ||||
| alpsIfHLinkX25ProtocolTypeReports the encapsulation type for this Serial Interface - AX.25 or EMTOX. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.4.2.1.3 | ||||
| alpsIfHLinkAx25PvcDampThe purpose of this object is to handle the link-damping for an AX.25 host. If the PVC goes inactive (i.e. link goes down, etc...) for PVCDampValue seconds, then PVC will be destroyed as well as the associated ALPS cir… | SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647Description: A period of time, measured in units of 0.01 seconds. | .1.3.6.1.4.1.9.9.95.1.4.2.1.4 | ||||
| alpsIfHLinkEmtoxHostX121Specfies the X.121 address of this EMTOX host. | RFC1382-MIBX121Address Type Constraints: range: 0..17 | .1.3.6.1.4.1.9.9.95.1.4.2.1.5 | ||||
| alpsIfHLinkActiveCktsReports the number of ALPS Ckts established with this host. | circuitsInteger32 Constraints: range: 0-4096 | .1.3.6.1.4.1.9.9.95.1.4.2.1.6 |
alpsAscuTable
table.1.3.6.1.4.1.9.9.95.1.5.1
·
1 row entry
·
20 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsAscuTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsAscuTable'
A list of ALPS ASCUs on an interface. This is defined only at the remote router.
Details of ASCU.
Indexes
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsAscuIdSpecifies the ASCU Identifier and uniquely identifies an ASCU on a given interface. This value is the Interface Address (IA) for ALC and the Remote Identifier (RID) for UTS. This uniquely identifies an ASCU on a given i… | Integer32 Constraints: range: 1-127 | .1.3.6.1.4.1.9.9.95.1.5.1.1.1 | ||||||||||||
| alpsAscuA1A1 value of the ASCU. | AlpsAscuA1A2Valuer/w Type Constraints: range: 0..255 | .1.3.6.1.4.1.9.9.95.1.5.1.1.2 | ||||||||||||
| alpsAscuA2A2 value of the ASCU. | AlpsAscuA1A2Valuer/w Type Constraints: range: 0..255 | .1.3.6.1.4.1.9.9.95.1.5.1.1.3 | ||||||||||||
| alpsAscuCktNameSpecifies the ALPS Circuit Name for the circuit that is to be used for this ASCU's data. Note that all ASCUs on a physical interface may not use the same ALPS circuit to connect to the central router | AlpsCktNamer/w Type Constraints: range: 1..12 | .1.3.6.1.4.1.9.9.95.1.5.1.1.4 | ||||||||||||
| alpsAscuAlarmsEnabledSpecifies whether alarms (syslog messages or SNMP traps) will be generated for this ASCU. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.5.1.1.5 | ||||||||||||
| alpsAscuRetryOptionSpecifies the retry option for this ASCU. This specifies the error message to be sent to the terminal when a message is dropped at the router. The terminal has three choices - either retransmit the last message (if the … | Enumerationr/w Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.5.1.1.6 | ||||||||||||
| alpsAscuMaxMsgLengthSpecifies Maximum length of Input Message that can be received from this ASCU. | bytesInteger32r/w Constraints: range: 1-3840 | .1.3.6.1.4.1.9.9.95.1.5.1.1.7 | ||||||||||||
| alpsAscuFwdStatusOptionIf this flag is set, status messages received from the ASCU are forwarded to the host. Otherwise they are discarded. Note that these are relevant only for P1024C (UTS). For ALC, a value of FALSE will be returned. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.5.1.1.8 | ||||||||||||
| alpsAscuStateReports the current ASCU Status. ASCUs are initially in disabled state. They are enabled from the parser if the operator wants to. This takes them to an UP state from which they go to a DOWN state if there are too many… | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.5.1.1.9 | ||||||||||||
| alpsAscuDownReasonReports the Down reason for this ASCU if it is down. | Enumeration Enumerated Values:
| .1.3.6.1.4.1.9.9.95.1.5.1.1.10 | ||||||||||||
| alpsAscuOutPacketsNumber of packets transmitted to this ASCU. | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.11 | ||||||||||||
| alpsAscuOutOctetsNumber of octets transmitted to this ASCU. | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.12 | ||||||||||||
| alpsAscuInPacketsNumber of packets received from this ASCU | packetsSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.13 | ||||||||||||
| alpsAscuInOctetsNumber of octets received from this ASCU. | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.14 | ||||||||||||
| alpsAscuDropsGarbledPktsThe number of packets dropped due to the inability to properly decode them. Examples of garbled packets include packets with bad CRCs or bad header information | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.15 | ||||||||||||
| alpsAscuDropsAscuDownThe number of packets dropped because the ASCU had previously been declared DOWN due to error thresholds being exceeded. | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.16 | ||||||||||||
| alpsAscuDropsAscuDisabledThe number of packets dropped because the ASCU had previously been declared to be in disabled state. | SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295 | .1.3.6.1.4.1.9.9.95.1.5.1.1.17 | ||||||||||||
| alpsAscuEnabledSpecifies whether the ASCU has been enabled or not. After the ASCU has been configured, it must be explicitly enabled to allow it to be polled. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.5.1.1.18 | ||||||||||||
| alpsAscuRowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.5.1.1.19 | ||||||||||||
| alpsAscuAutoResetSpecifies whether a reset command will be automatically issued to any non-responsive ALC ASCUs. | SNMPv2-TCTruthValuer/w Type Values:
Description: Represents a boolean value. | .1.3.6.1.4.1.9.9.95.1.5.1.1.20 |
alpsSvcMsgTable
table.1.3.6.1.4.1.9.9.95.1.6.1
·
1 row entry
·
4 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsSvcMsgTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsSvcMsgTable'
A list of service messages and its associated number. There is a default list of service messages (list 0) as well as user-configurable service messages. On a per-circuit basis, the service message list to use can be selected. The user-configured service message lists are defined in this table. Note that the default service messages are not part of this table.
Service Messages configured along with its List number and Service
Message Number in that list.
Message Number in that list.
Indexes
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsSvcMsgListNumSpecifies the Service Msg Number of this Service Msg. A maximum of 8 Service Message lists can be configured not including the one for Default/System (when alpsSvcMsgListNum = 0) Service messages. | Integer32 Constraints: range: 1-8 | .1.3.6.1.4.1.9.9.95.1.6.1.1.1 | ||||||||||||
| alpsSvcMsgNumSpecifies the Service Msg Number of this Service Msg. A Maximum of 8 messages can be present. | Integer32 Constraints: range: 1-8 | .1.3.6.1.4.1.9.9.95.1.6.1.1.2 | ||||||||||||
| alpsSvcMsgSpecifies the Service Message string . | OctetStringr/w Constraints: range: 1-50 | .1.3.6.1.4.1.9.9.95.1.6.1.1.3 | ||||||||||||
| alpsSvcMsgRowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.6.1.1.4 |
alpsX121ToIpTransTable
table.1.3.6.1.4.1.9.9.95.1.6.2
·
1 row entry
·
3 columns
Uses the cisco variant from
Command help
/opt/observium/mibs/cisco.
Walk alpsX121ToIpTransTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-ALPS-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-ALPS-MIB::alpsX121ToIpTransTable'
A Translation table between X.121 address and IP address. This is intended to allow a connection to be established to the appropriate remote router. The X121 address in the call packet is used to look up the IP address of the remote peer
A mapping table between X.121 address and IP address.
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| alpsX121Specfies the X.121 address of the VC established with EMTOX host. | RFC1382-MIBX121Address Type Constraints: range: 0..17 | .1.3.6.1.4.1.9.9.95.1.6.2.1.1 | ||||||||||||
| alpsIpAddressThis is the IP address of the remote peer which maps onto the X.121 address. | SNMPv2-SMIIpAddressr/w Type Constraints: range: 4 | .1.3.6.1.4.1.9.9.95.1.6.2.1.2 | ||||||||||||
| alpsX121ToIpTransRowStatusThis object is used to create a new row or modify or delete an existing row in this table. | SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … | .1.3.6.1.4.1.9.9.95.1.6.2.1.3 |