BRCM-80211-MGMT-MIB Table View

A table of entries in an MBSS system.

dot11BssEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1

An entry describing the characteristics of an individual BSS. An
entry exists in this table for each entry of type ieee80211 (71) in
the ifTable.

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot11BssId The physical address associated with this service set.	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.1
dot11BssEnable Enables or disables this service set.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.2
dot11BssSsid Controls and reflects the service set identifier for this BSS.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.3
dot11BssNetworkBridgedeprecated If set to lan(1), this service set will be authorized as a member of the local area network. If set to guest(2), this service set will have access to the wide area internet, but will have restricted access to the local…	Enumerationr/w Enumerated Values: 1 lan 2 guest	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.4
dot11BssSecurityMode Security mode may be chosen from Disable, WEP, WPA-PSK, WPA2-PSK, WPA-Enterprise, WPA2-Enterprise or RADIUS-WEP. All devices on the network must use the same security mode in order to communicate. If se…	Enumerationr/w Enumerated Values: 0 disabled 1 wep 2 wpaPsk 3 wpa2Psk 4 wpaEnterprise 5 wpa2Enterprise 6 radiusWep	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.5
dot11BssClosedNetwork Controls whether the device will operate in closed network mode. If set to true(1), then the network mode is closed and the SSID will not be broadcast in beacon packets. If set to false(2), then the network mode is op…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.6
dot11BssAccessMode Controls what stations will be given access to the device. If set to allowAny(1), then any station will be allowed to connect. If set to restrictToList(2), then only stations whose MAC address appears in the dot11BssA…	Enumerationr/w Enumerated Values: 1 allowAny 2 allowList 3 denyList	.1.3.6.1.4.1.4413.2.2.2.1.5.4.1.14.1.7

A table used to configure settings related to the WEP security modes.

dot11BssWepEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.2.1.1

An entry defining the WPA characteristics of an individual service set.
A row exists in this table for each row in the dot11BssTable for which
dot11BssSecurityMode is set to wep(1) or radiusWep(6).

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot11BssWepDefaultKey Controls and reflects the default key which will be used when 64 or 128 bit encryption is enabled. Indicates the entry from the dot11BssWep64BitKeyTable if dot11EncryptionMode is set to wep64(1), or the entry from the…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.1.1.1
dot11BssWepEncryptionMode Selects the WEP encryption method used by this service set. If set to wep64(1), then 64 bit WEP encryption will be used with the keys from the dot11BssWep64BitKeyTable. If set to wep128(2), then 128 bit WEP encryption…	Enumerationr/w Enumerated Values: 1 wep64 2 wep128	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.1.1.2
dot11BssWepPassPhrase The passphrase used for WEP security.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.1.1.3

A table of 40 bit key values used when operating in WEP 64 mode.

dot11BssWep64BitKeyEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.2.2.1

A key to be used by the row in the dot11BssTable identified by the
value of ifIndex in the row index.

Indexes

IF-MIBifIndex dot11BssWep64BitKeyIndex

Column	Syntax	OID
dot11BssWep64BitKeyIndex Identifies an instance of a key among those used by the service set identified by the value of ifIndex in the row index.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.2.1.1
dot11BssWep64BitKeyValue A 40 bit key to be used when the corresponding instance of dot11BssSecurityMode is set to wep(1) and the corresponding instance of dot11BssWepEncryptionMode is set to wep64(1).	OctetStringr/w Constraints: range: 5-5	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.2.1.2
dot11BssWep64BitKeyStatus The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.2.1.3

A table of 104 bit key values used when operating in WEP 128 mode.

dot11BssWep128BitKeyEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.2.3.1

A key to be used by the row in the dot11BssTable identified by the
value of ifIndex in the row index.

Indexes

IF-MIBifIndex dot11BssWep128BitKeyIndex

Column	Syntax	OID
dot11BssWep128BitKeyIndex Identifies an instance of a key among those used by the service set identified by the value of ifIndex in the row index.	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.3.1.1
dot11BssWep128BitKeyValue A 104 bit key to be used when the corresponding instance of dot11BssSecurityMode is set to wep(1) and the corresponding instance of dot11BssWepEncryptionMode is set to wep128(128).	OctetStringr/w Constraints: range: 13-13	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.3.1.2
dot11BssWep128BitKeyStatus The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.3.1.3

A table used to configure settings related to the WPA security modes.

dot11BssWpaEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.2.4.1

An entry defining the WPA characteristics of an individual service set.
A row exists in this table for each row in the dot11BssTable for which
dot11BssSecurityMode is set to wpaPsk(2), wpa2Psk(3), wpaEnterprise(4),
or …

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot11BssWpaAlgorithm Controls and reflects the WPA encryption mode used by the service set. The WPA algorithm for WPA-PSK and WPA-Enterprise security mode is either tkip(1) or aes(2). The WPA algorithm for WPA2-PSK and WPA2…	Enumerationr/w Enumerated Values: 1 tkip 2 aes 3 tkipPlusAes	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.4.1.1
dot11BssWpaPreSharedKey Sets the WPA Pre-Shared Key (PSK) used by this service set. This value MUST be either a 64 byte hexadecimal number, OR an 8 to 63 character ASCII string.	OctetStringr/w Constraints: range: 8-64	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.4.1.2
dot11BssWpaGroupRekeyInterval Sets the WPA Group Rekey Interval for this service set. If set to zero, periodic rekeying is disabled for this service set.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.4.1.3

A table used to configure settings related to the RADIUS security 
modes, including WPA-Enterprise, WPA2-Enterprise and RADIUS-WEP.

dot11BssRadiusEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1

An entry defining the RADIUS characteristics of an individual service
set. A row exists in this table for each row in the dot11BssTable
for which dot11BssSecurityMode is set to wpaEnterprise(4),
wpa2Enterprise(5), o…

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot11BssRadiusAddressType The type of internet address used for dot11BssRadiusAddress.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1.1
dot11BssRadiusAddress The internet address of the RADIUS server for this service set.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1.2
dot11BssRadiusPort The UDP port used to communicate with the RADIUS server for this service set.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1.3
dot11BssRadiusKey The RADIUS key.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1.4
dot11BssRadiusReAuthInterval The network re-authentication interval. If set to zero, no re-authentication will be performed.	secondsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4413.2.2.2.1.5.4.2.5.1.5

A table of MAC addresses which defines the MAC address based access 
restrictions for the system.

dot11BssAccessEntry row .1.3.6.1.4.1.4413.2.2.2.1.5.4.3.1.1

A row in the table which specifies a single MAC address for a given
service set.

Indexes

IF-MIBifIndex dot11BssAccessIndex

Column	Syntax	OID
dot11BssAccessIndex Indicates the instance of this table row.	Integer32 Constraints: range: 1-16	.1.3.6.1.4.1.4413.2.2.2.1.5.4.3.1.1.1
dot11BssAccessStation A MAC address of a station which will be allowed to connect to the service set if dot11BssAccessMode is set to restrictToList(2), or forbidden if dot11BssAccessMode is set to denyList(3).	SNMPv2-TCPhysAddressr/w Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.4413.2.2.2.1.5.4.3.1.1.2
dot11BssAccessStatus The status of this conceptual row. To create a row in this table, a manager must set this object to either createAndGo(4) or createAndWait(5). Until instances of all corresponding columns …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4413.2.2.2.1.5.4.3.1.1.3