BINTEC-MOBILE-MIB Table View

The mobileDevCfgTable configures the detected mobile device
identified by the IMEI (International Mobile Equipment Identity).

mobileDevCfgEntry row .0.4.1.20.1

A single mobileDevCfgTable entry.

Indexes

mobileDevCfgIMEI

Column	Syntax	OID
mobileDevCfgIMEI The IMEI (International Mobile Equipment Identity) of the mobile device to configure.	OctetStringr/w Constraints: range: 0-32	.0.4.1.20.1.1
mobileDevCfgInit Additional Modem hardware init sequence. This sequence will be send to the modem to initialize it. Normally this string should be empty (un-used).	OctetStringr/w Constraints: range: 0-80	.0.4.1.20.1.2
mobileDevCfgGPSEnable Enables or disables the creation and periodic update of a mobileGPSInfoTable entry. The UMTS Modem Hardware must support GPS functionality. This is indicated by the Object `mobileStatGpsSupport'.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled 3 delete	.0.4.1.20.1.3
mobileDevCfgModulation The Modulation to be used by the modem. With auto(1) the modulation will be automatically chosen. mdm_9600(2) sets the modulation to 9600 bps (V.32). mdm_14400(3) sets the modulation to 14400 bps (V.34). The values v110…	Enumerationr/w Enumerated Values: 1 auto 2 mdm-9600 3 mdm-14400 4 v110-9600 5 v110-14400 6 v120 7 gprs	.0.4.1.20.1.4

The mobileSimCfgTable configures each corresponding
SIM-Card identified by the cards unique ICC-ID.

mobileSimCfgEntry row .0.4.1.21.1

A single mobileSimCfgTable entry.

Indexes

mobileSimCfgIccId

Column	Syntax	OID
mobileSimCfgIccId The ICC-ID of the used SIM-Card to configure. Unfortunately some UMTS modem vendors offer no capability to read this ID before entering the valid PIN :-(	OctetStringr/w Constraints: range: 0-32	.0.4.1.21.1.1
mobileSimCfgPIN The PIN code of the SIM card. This is used to authorize the access to the SIM-Card.	OctetStringr/w Constraints: range: 0-8	.0.4.1.21.1.2
mobileSimCfgPUK The PUK code of the SIM card. Needed in case of wrong PIN input for three times in a row.	OctetStringr/w Constraints: range: 0-16	.0.4.1.21.1.3
mobileSimCfgAPN GPRS APN (Access Point Name) used by this SIM-Card.	OctetStringr/w Constraints: range: 0-80	.0.4.1.21.1.4
mobileSimCfgAccessMode The default Access Type to be used by the GPRS/UMTS/LTE Modem. This setting depends on local network availability and therefore it's bound to the network operator specific SIM-Card. Possible settings are: auto(1) …	Enumerationr/w Enumerated Values: 1 auto 2 gprs-only 3 umts-only 4 gprs-pref 5 umts-pref 6 delete 7 lte-only 8 lte-pref 9 lte-umts 10 lte-gprs 11 lte-gprs-umts 12 umts-lte 13 umts-gprs 14 umts-lte-gprs 15 gprs-lte 16 gprs-umts 17 gprs-lte-umts	.0.4.1.21.1.5
mobileSimCfgRoamingMode The Roaming configuration for this mobile interface. Possible values are: disabled - no roaming at all auto - roaming decision by modems factory defaults unrestricted - no restrictions for roa…	Enumerationr/w Enumerated Values: 1 disabled 2 auto 3 unrestricted 4 international 5 national 6 fixed 7 full-auto	.0.4.1.21.1.6
mobileSimCfgRoamingPLMN The PLMN (Public Land Mobile Netword) code used for Roaming. Used only if mobileDevCfgRoamingMode_fixed is selected.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.21.1.7
mobileSimCfgDispatch The dispatch service the Modem should be used for. The SIM-Card should support/enable basic functionality to use the service (eg access circuit switched networks to use V.110 and/or V.120). Routing tasks (IP, IPX, X.25,…	Enumerationr/w Enumerated Values: 1 ppp 2 isdnlogin 3 none 13 ppp-modem 15 ppp-v110-1200 16 ppp-v110-2400 17 ppp-v110-4800 18 ppp-v110-9600 19 ppp-v110-14400 20 ppp-v110-19200 21 ppp-v110-38400 23 ppp-v120 26 ppp-modem-profile-1 27 ppp-modem-profile-2 28 ppp-modem-profile-3 29 ppp-modem-profile-4 30 ppp-modem-profile-5 31 ppp-modem-profile-6 32 ppp-modem-profile-7 33 ppp-modem-profile-8 60 ipsec	.0.4.1.21.1.8
mobileSimCfgGsmFallback If the Router is called using the GsmFallback number the actual connection is dropped and the Access Type is switched back from UMTS to GSM.	OctetStringr/w Constraints: range: 0-32	.0.4.1.21.1.9
mobileSimCfgCugAddr The provider assigned IP-Address if any.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.0.4.1.21.1.15
mobileSimCfgCugAuth The authentication method to be used.	Enumerationr/w Enumerated Values: 1 none 2 pap 3 chap 4 pap-chap	.0.4.1.21.1.16
mobileSimCfgCugUser The provider assigned user name.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.4.1.21.1.17
mobileSimCfgCugPwd The provider assigned password.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.4.1.21.1.18
mobileSimCfgOperatorScan Handling of scanning available Providers (PLMN) never - use only home or fixed PLMN startup - scan on startup, only for information always - used for using roaming PLMN outside own country	Enumerationr/w Enumerated Values: 1 never 2 startup 3 always	.0.4.1.21.1.19
mobileSimCfgPinData Not accessible entry for storing the PIN permanently. This is a security feature (?) used by France Telecom.	OctetString Constraints: range: 0-16	.0.4.1.21.1.20
mobileSimCfgCugAPN Closed User Group authentication APN, may be different from registration APN.	OctetStringr/w Constraints: range: 0-80	.0.4.1.21.1.21

The mobileStatTable holds statistics about the actually
detected and/or used mobile device.

mobileStatEntry row .0.4.1.22.1

A single mobileStatTable entry.

Indexes

mobileStatIfIndex

Column	Syntax	OID
mobileStatIfIndex The interface index of the corresponding TTY interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.1
mobileStatOperStatus The operational status of the GSM modem. The following states can occur: - up(1) the device is up - initialization finished - down(2) the device is down - init(3) initialization state - cal…	Enumeration Enumerated Values: 1 up 2 down 3 init 4 called 5 calling 6 connect 7 simwait 8 pinwait 9 error 10 disconnected 11 pukwait 12 regwait 13 apnwait	.0.4.1.22.1.2
mobileStatErrorCode If an error occurs (OperStatus is set to error) this variable shows the reason for the error. Currently the following error codes are possible: - none(1) no error occured - unspecified(2) error can't be specified…	Enumeration Enumerated Values: 1 none 2 unspecified 3 pinerror 4 pukerror 5 apnerror 6 simerror 7 reg-denied	.0.4.1.22.1.3
mobileStatCommand The last command that was sent to the mobile device.	OctetString Constraints: range: 0-60	.0.4.1.22.1.4
mobileStatAnswer The last answer received from the mobile device.	OctetString Constraints: range: 0-60	.0.4.1.22.1.5
mobileStatInDiscards The number of frames which can't be enqueued upstream.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.6
mobileStatSelectedPLMN The PLMN (Public Land Mobile Network) code of the Network currently selected.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.7
mobileStatNetwork The name of the PLMN (Public Land Mobile Network) actually being used.	OctetString Constraints: range: 0-60	.0.4.1.22.1.8
mobileStatLocationAreaCode The actual Location Area Code the UMTS-Modem is registered.	OctetString Constraints: range: 0-16	.0.4.1.22.1.9
mobileStatCellId The actual Cell-ID the UMTS-Modem is registered.	OctetString Constraints: range: 0-16	.0.4.1.22.1.10
mobileStatAccessType The Access Type the modem actually registers on. Normally the `edge' or `hs*pa' Access Types aren't provided in detail by the network operator and/or modem. Possible Access Types are: unknown(1) gsm(2) -…	Enumeration Enumerated Values: 1 unknown 2 gsm 3 compact-gsm 4 umts 5 gsm-edge 6 umts-hsdpa 7 umts-hsupa 8 umts-hspa 9 lte 10 hspa-plus 11 cdma-rev0 12 cdma-revA 13 cdma-revB	.0.4.1.22.1.11
mobileStatCSQ The GSM receive signal level in decibel (db). A value below -100 signals a very low signal quality. A value between -100 and -80 means that signal quality is low. If the value is between -80 and -70 the quality is ok. T…	dBmSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.12
mobileStatIMEI The IMEI (International Mobile Equipment Identity) of the detected mobile device.	OctetString Constraints: range: 0-32	.0.4.1.22.1.13
mobileStatCtrlIfIndex If the UMTS card provides several channels and one could be used to control the card e.g. get status information from the card like the signal quality a dedicated daemon uses the mobileStatCtrlIfIndex for this purpose. …	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.14
mobileStatGpsSupport Signals for configuration software if the hardware is capable to deliver GPS information. - none(1) no GPS support - available(2) GPS support available	Enumeration Enumerated Values: 1 none 2 available	.0.4.1.22.1.15
mobileStatIccId The ICC-ID of the SIM-Card found in the mobile device which is actually enumerated with mobileStatIfIndex. Some UMTS modem vendors offer no capability to read this ID before entering a valid PIN :-( In th…	OctetString Constraints: range: 0-32	.0.4.1.22.1.16
mobileStatHomePLMN The PLMN (Public Land Mobile Network) code of the Home PLMN.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.22.1.17
mobileStatSubscriberNumber The Subscriber Number stored on the SIM card.	OctetString Constraints: range: 0-32	.0.4.1.22.1.18
mobileStatServiceCenterAddr The Service Center Address stored on the SIM card.	OctetString Constraints: range: 0-32	.0.4.1.22.1.19
mobileStatLteSupport Signals for configuration software if the hardware is capable to attach to LTE networks. - none(1) no LTE support - available(2) LTE support available	Enumeration Enumerated Values: 1 none 2 available	.0.4.1.22.1.20
mobileStatBand The Band Class currently used.	Enumeration Enumerated Values: 0 cdma-band-0 1 cdma-band-1 3 cdma-band-3 4 cdma-band-4 5 cdma-band-5 6 cdma-band-6 7 cdma-band-7 8 cdma-band-8 9 cdma-band-9 10 cdma-band-10 11 cdma-band-11 12 cdma-band-12 13 cdma-band-13 14 cdma-band-14 15 cdma-band-15 16 cdma-band-16 40 gsm-450 41 gsm-480 42 gsm-750 43 gsm-850 44 gsm-900-ext 45 gsm-900-pri 46 gsm-900-rway 47 gsm-1800 48 gsm-1900 80 wcdma-2100 81 wcdma-pcs-1900 82 wcdma-dcs-1800 83 wcdma-1700-us 84 wcdma-650 85 wcdma-800 86 wcdma-2600 87 wcdma-900 88 wcdma-1700-jp 120 e-utra-band-1 121 e-utra-band-2 122 e-utra-band-3 123 e-utra-band-4 124 e-utra-band-5 125 e-utra-band-6 126 e-utra-band-7 127 e-utra-band-8 128 e-utra-band-9 129 e-utra-band-10 130 e-utra-band-11 131 e-utra-band-12 132 e-utra-band-13 133 e-utra-band-14 134 e-utra-band-17 135 e-utra-band-33 136 e-utra-band-34 137 e-utra-band-35 138 e-utra-band-36 139 e-utra-band-47 140 e-utra-band-38 141 e-utra-band-39 142 e-utra-band-40 143 e-utra-band-18 144 e-utra-band-19 145 e-utra-band-20 146 e-utra-band-21 255 unknown	.0.4.1.22.1.21
mobileStatSmsStorageBits The SMS storage types supported by the modem hardware.	Bits Enumerated Values: 1 sm 2 me 3 mt 4 bm 5 ta 6 sr	.0.4.1.22.1.22
mobileStatAction Perform extern triggered Action on sierra wireless modems - idle no waiting Action - reset reset the modem - qmi switch modem into qmi mode - dip switch modem into direct IP mode - dhcpr…	Enumerationr/w Enumerated Values: 1 idle 2 reset 3 qmi 4 dip 5 dhcprelay	.0.4.1.22.1.23
mobileStatATexec Perform a User requested AT Command in idle state	OctetStringr/w Constraints: range: 0-255	.0.4.1.22.1.24

The mobileOperatorTable shows the actually available 
network provider and the registration status.

mobileOperatorEntry row .0.4.1.23.1

A single mobileOperatorTable entry.

Indexes

mobileOperatorIfIndex mobileOperatorCode mobileOperatorAcT

Column	Syntax	OID
mobileOperatorIfIndex The index of the corresponding TTY interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.23.1.1
mobileOperatorCode The PLMN code of the network operator.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.23.1.2
mobileOperatorAcT The Access Type the modem actually registers on. Normally the `edge' or `hs*pa' Access Types aren't provided in detail by the network operator and/or modem. Possible Access Types are: unknown(1) gsm(2) -…	Enumeration Enumerated Values: 1 unknown 2 gsm 3 compact-gsm 4 umts 5 gsm-edge 6 umts-hsdpa 7 umts-hsupa 8 umts-hspa 9 lte 10 hspa-plus 11 cdma-rev0 12 cdma-revA 13 cdma-revB	.0.4.1.23.1.3
mobileOperatorStatus The registration status depending on the network operator. The following states can occur: - unknown(1) -- no idea - available(2) -- registration possible - current(3) -- successfully registered - forbidden(4) -- no…	Enumeration Enumerated Values: 1 unknown 2 available 3 current 4 forbidden	.0.4.1.23.1.4
mobileOperatorName The name of the network operator.	OctetString Constraints: range: 0-60	.0.4.1.23.1.5
mobileOperatorPriority The Priority of the Operator to use in roaming mode. There are different priority value ranges for the following types of operator entries: - Home Operator (from SIM card) - Priviledged Operator (from SIM…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.23.1.6
mobileOperatorPreference The registration priority for the network operator. The following states can occur: - home(1) -- home operator - privileged(2) -- home operators best roaming partner - preferred(3) -- home operators roam…	Enumeration Enumerated Values: 1 home 2 privileged 3 preferred 4 practicable 5 banned 6 administrative	.0.4.1.23.1.7
mobileOperatorCurrentOrder The order of the entry in the currently used internal roaming list, the value '-1' indicates an unused (ignored) entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.23.1.8

The mobileSmsSendTable holds all information to send
a SMS (Short Message Service) via a GSM/UMTS modem.

mobileSmsSendEntry row .0.4.1.24.1

A single mobileSmsSendTable entry.
This entry is temporary until it's successfully sent.
After being successfully sent this entry is copied to
the mobileSmsTable. Since the GSM/UMTS modem stores
the SMS internally or on…

Indexes

mobileSmsSendId

Column	Syntax	OID
mobileSmsSendId A unique ID generated by the application which triggers the SMS send request.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.24.1.1
mobileSmsSendIfIndex The interface index of the mobile device which should transmit the SMS.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.24.1.2
mobileSmsSendMsgStorage This object specifies the storage which holds the SMS. Available storages are: sm(1) -- SIM card storage me(2) -- Mobile Equipment storage The default of this object is 'me' because mobile equipment offers more …	Enumerationr/w Enumerated Values: 1 sm 2 me	.0.4.1.24.1.3
mobileSmsSendMsgSlot The actual index to address the SMS in 'mobileSmsSendMsgStorage'. This index is returned by the mobile device after the store operation is successfully finished.	Integer32 Constraints: range: -1-65535	.0.4.1.24.1.4
mobileSmsSendMsgStatus The Status of the SMS. To start transmission of the SMS set Status to `transmit(1)'. On successful transmission the Status is set to `success(2)'. Afterwards the SMS is moved to the 'mobileSmsTable'. …	Enumerationr/w Enumerated Values: 1 transmit 2 success 3 error 5 delete	.0.4.1.24.1.5
mobileSmsSendDestAddr The destination address of this SMS.	OctetStringr/w Constraints: range: 0-64	.0.4.1.24.1.6
mobileSmsSendMsgFormat The message format of the SMS. Traditional SMS use plain `txt(2)' format. Special or Unicode SMS use `pdu(1)' format.	Enumerationr/w Enumerated Values: 1 pdu 2 txt	.0.4.1.24.1.7
mobileSmsSendMsgCoding This object specifies the coding of the SMS user data section.	Enumerationr/w Enumerated Values: 1 ira 2 gsm 3 ucs2 4 pc437 5 iso8859-1	.0.4.1.24.1.8
mobileSmsSendMsgData The raw text data of the SMS depending on the coding.	OctetStringr/w Constraints: range: 0-160	.0.4.1.24.1.9

The mobileSmsTable holds all SMS (Short Message Service)
which are stored in the GSM/UMTS modem and/or on the SIM-
Card used.

mobileSmsEntry row .0.4.1.25.1

A single mobileSmsTable entry.
Each entry is a copy of a SMS stored in the GSM/UMTS modem
and/or on the SIM-Card used.
Status information like 'received-unread', 'received-read',
'stored-unsent' and 'stored-sent' is add…

Indexes

mobileSmsIfIndex mobileSmsMsgStorage mobileSmsMsgSlot

Column	Syntax	OID
mobileSmsIfIndex The interface index of the mobile device which received the SMS or should transmit it.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.25.1.1
mobileSmsMsgStorage This object specifies the storage which holds the SMS. Available storages are: sm(1) -- SIM card storage me(2) -- Mobile Equipment storage mt(3) -- one of the ME associated storages bm(4) -- Broadcast Me…	Enumeration Enumerated Values: 1 sm 2 me 3 mt 4 bm 5 ta 6 sr	.0.4.1.25.1.2
mobileSmsMsgSlot The actual index to address the SMS in 'mobileSmsMsgStorage'.	Integer32 Constraints: range: 0-65535	.0.4.1.25.1.3
mobileSmsMsgStatus The status of the SMS. The first four states correspond with 3GPP TS27.005. For incoming SMS the Status is set to `rec-unread(1)'. After reading the SMS the Status is set to `rec-read(2)'. On storing …	Enumerationr/w Enumerated Values: 1 rec-unread 2 rec-read 3 sto-unsent 4 sto-sent 5 delete	.0.4.1.25.1.4
mobileSmsServiceCenterTimeStamp The date/time the SMS is sent or received.	OctetString Constraints: range: 0-64	.0.4.1.25.1.5
mobileSmsServiceCenterAddress The Service Center Address used to send or receive this SMS.	OctetString Constraints: range: 0-64	.0.4.1.25.1.6
mobileSmsPhoneNumber The origination or destination address of this SMS depending on the value of 'mobileSmsMsgStatus'.	OctetString Constraints: range: 0-64	.0.4.1.25.1.7
mobileSmsMsgFormat The message format of the SMS. Traditional SMS use plain `txt(2)' format. Special or Unicode SMS use `pdu(1)' format.	Enumeration Enumerated Values: 1 pdu 2 txt	.0.4.1.25.1.8
mobileSmsMsgCoding This object specifies the coding of the SMS user data section.	Enumeration Enumerated Values: 1 ira 2 gsm 3 ucs2 4 pc437 5 iso8859-1 6 uh-7bit 7 uh-8bit	.0.4.1.25.1.9
mobileSmsMsgData The raw data of the complete SMS.	OctetString Constraints: range: 0-160	.0.4.1.25.1.10

The mobileGPSInfoTable shows the actually available 
GPS information if supported by the Hardware.

mobileGPSInfoEntry row .0.4.1.26.1

A single mobileGPSInfoTable entry.

Indexes

mobileGPSInfoIfIndex

Column	Syntax	OID
mobileGPSInfoIfIndex The index of the corresponding TTY interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.26.1.1
mobileGPSInfoOperStatus The operation status of the UMTS modems internal GPS module. The following states can occur: - unknown(1) -- initialization failed - down(2) -- GPS module disabled - init(3) -- GPS module is looking for satelites …	Enumeration Enumerated Values: 1 unknown 2 down 3 init 4 up	.0.4.1.26.1.2
mobileGPSInfoDate The actual date calculated from GPS info.	OctetString Constraints: range: 0-16	.0.4.1.26.1.3
mobileGPSInfoTime The actual time calculated from GPS info.	OctetString Constraints: range: 0-16	.0.4.1.26.1.4
mobileGPSInfoLatitude The actual Latitude calculated from GPS info.	OctetString Constraints: range: 0-32	.0.4.1.26.1.5
mobileGPSInfoLongitude The actual Longitude calculated from GPS info.	OctetString Constraints: range: 0-32	.0.4.1.26.1.6
mobileGPSInfoSpeedOverGround The actually detected Speed over Ground.	Integer32 Constraints: range: 0-65535	.0.4.1.26.1.7
mobileGPSInfoNumberOfSatelites The number of satelites actually found by the GPS module.	Integer32 Constraints: range: 0-34	.0.4.1.26.1.8

The mobilePLMNTable holds the PLMN (Public Land
Mobile Network) codes known by the mobile device.
This table is used to translate PLMN code into name.

mobilePLMNEntry row .0.4.1.27.1

A single mobilePLMNTable entry.

Indexes

mobilePLMNCode

Column	Syntax	OID
mobilePLMNCode The PLMN (Public Land Mobile Network) code of the network operator. This code is merged from the MCC (Mobile Country Code) and MNC (Mobile Network Code) of the network operator.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.27.1.1
mobilePLMNName The name of the network operator.	OctetString Constraints: range: 0-20	.0.4.1.27.1.2

The mobileOperatorPLMNTable shows the Operator_controlled_PLMN
(Public Land Mobile Networks) codes accessible by the SIM-Card.

mobileOperatorPLMNEntry row .0.4.1.28.1

A single mobileOperatorPLMNTable entry.

Indexes

mobileOperatorPLMNIccId mobileOperatorPLMNCode

Column	Syntax	OID
mobileOperatorPLMNIccId The ICC-ID of the SIM-Card. The Operator PLMN List is copied from this SIM-Card.	OctetString Constraints: range: 0-20	.0.4.1.28.1.1
mobileOperatorPLMNCode The PLMN Code is built from a 3 digit MCC (Mobile Country Code) and 2 or 3 digit MNC (Mobile Network Code).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.28.1.2
mobileOperatorPLMNName The name of the network operator.	OctetString Constraints: range: 0-40	.0.4.1.28.1.3
mobileOperatorPLMNAllowGSM The Access Right to register to GSM Access Technology.	Enumeration Enumerated Values: 1 allowed 2 denied	.0.4.1.28.1.4
mobileOperatorPLMNAllowUMTS The Access Right to register to UMTS Access Technology.	Enumeration Enumerated Values: 1 allowed 2 denied	.0.4.1.28.1.5

The mobilePdpContextTable shows the PDP (Packet Data Protocol)
context stored in the detected mobile device. The mobile device
is identified by the unique IMEI (International Mobile Equipment
Identity).

mobilePdpContextEntry row .0.4.1.29.1

A single mobilePdpContextTable entry.

Indexes

mobilePdpContextIndex

Column	Syntax	OID
mobilePdpContextIndex A unique index for this entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.29.1.1
mobilePdpContextIfIndex The interface index of the corresponding TTY interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.4.1.29.1.2
mobilePdpContextPrimaryId The primary PDP context identifier.	Integer32 Constraints: range: 1-16	.0.4.1.29.1.3
mobilePdpContextSecondaryId Shows the secondary PDP context identifier (non-zero). In case of a primary PDP context this object is zero.	Integer32 Constraints: range: 0-16	.0.4.1.29.1.4
mobilePdpContextType The protocol type of the PDP context. This object is unused in case of a secondary PDP context.	Enumeration Enumerated Values: 1 ipv4 2 ppp 3 ipv6 4 ipv4v6	.0.4.1.29.1.5
mobilePdpContextAPN The APN (Access Point Name) used by the PDP context. This object is unused in case of a secondary PDP context.	OctetString Constraints: range: 0-128	.0.4.1.29.1.6
mobilePdpContextPreferredAddress The preferred (IP-)Address assigned to the PDP context.	OctetString Constraints: range: 0-64	.0.4.1.29.1.7
mobilePdpContextDataCompression The data compression used for data connections. This object is normally unused in 2G/3G/4G networks.	Enumeration Enumerated Values: 1 off 2 on 3 v42bis 4 v44	.0.4.1.29.1.8
mobilePdpContextHeaderCompression The header compression used for data connections. This object is normally unused in 2G/3G/4G networks.	Enumeration Enumerated Values: 1 off 2 on 3 rfc1144 4 rfc2507 5 rfc3095	.0.4.1.29.1.9

The mobileAdmOperatorTable shows the configured preferred PLMNs.

mobileAdmOperatorEntry row .0.4.1.30.1

A single mobileAdmOperatorTable entry.

Indexes

mobileAdmOperatorIccId mobileAdmOperatorCode

Column	Syntax	OID
mobileAdmOperatorIccId The ICC-ID of the SIM-Card. The operator is assigned to this SIM Id.	OctetStringr/w Constraints: range: 0-20	.0.4.1.30.1.1
mobileAdmOperatorCode The PLMN Code is built from a 3 digit MCC (Mobile Country Code) and 2 or 3 digit MNC (Mobile Network Code).	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.4.1.30.1.2
mobileAdmOperatorName The name of the network operator.	OctetStringr/w Constraints: range: 0-40	.0.4.1.30.1.3
mobileAdmOperatorAcT The AcT defines the Access technologies gsm - G2 connectivity umts - G3 connectivity lte - G4 connectivity	Bitsr/w Enumerated Values: 1 gsm 2 umts 3 lte	.0.4.1.30.1.4
mobileAdmOperatorPriority This value represents the relative priority of this entry. it is added to the admistrative base priority (see 'mobileOperatorPriority') to be used afterwards for the operator selection procedure. Under normal circumstan…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.4.1.30.1.5
mobileAdmOperatorStatus The operator's status. permit - the operator is allowed for roaming. deny - the operator is forbidden to use. delete - delete this entry	Enumerationr/w Enumerated Values: 1 permit 2 deny 8 delete	.0.4.1.30.1.6