BIANCA-ETH-PHY-MIB Table View

The ethPhyTable contains information relating to the 
interfaces available on the system. Each entry corresponds
to an available ethernet or switch port. Entries cannot be
added or deleted by the user. 
          
Creating entries: Entries are created by the system
automatically during ethernet interface hardware scan
and when a managable switch is detected.
          
Deleting entries: Entries can't be deleted.

ethPhyEntry row .0.1.1

The ethPhyEntry contains configuration and status information
of a physical interface associated to one ethernet interface.

Indexes

ethPhyPortIndex

Column	Syntax	OID
ethPhyPortIndex The unique ethernet PHY interface index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.0.1.1.1
ethPhyChipVendor The vendor name or identifier of the PHY or switch detected during hardware scan.	OctetString Constraints: range: 1-40	.0.1.1.2
ethPhyChipModel The chip modell/revision of the PHY or switch detected during hardware scan.	OctetString Constraints: range: 1-40	.0.1.1.3
ethPhyPortLinkStatus This variable indicates link status and autonegotiation results: down(1) -- link down or autonegotiation failed auto-neg-failed(2) -- autonegotiation failed auto-neg-unavail(3) -- autonegoti…	Enumeration Enumerated Values: 1 down 2 auto-neg-failed 3 auto-neg-unavail 4 auto-neg-running 5 auto-full-100 6 auto-half-100 7 auto-full-10 8 auto-half-10 9 full-100 10 half-100 11 full-10 12 half-10 13 admin-down 14 full-1000	.0.1.1.6
ethPhyPortMdixStatus This variable indicates the cables MDIX status if the link is established.	Enumeration Enumerated Values: 1 normal 2 crossover 3 unknown	.0.1.1.7
ethPhyPortCapabilities This bitfield describes what modes the port supports: half-10 : 10Mbit/s half duplex full-10 : 10Mbit/s full duplex half-100 : 100Mbit/s half duplex full-100 : 100Mbit/s full duplex half-1000 : 1000Mbit/s half duplex …	Bits Enumerated Values: 0 half-10 1 full-10 2 half-100 3 full-100 4 half-1000 5 full-1000 6 autoneg	.0.1.1.9
ethPhyPortMode The initial mode of the ethernet PHY or switch port: disable(1) -- disconnect from physical line auto(2) -- use default autonegotiation auto-100(3) -- use autonegotiation for …	Enumerationr/w Enumerated Values: 1 disable 2 auto 3 auto-100 4 auto-10 5 auto-full-100 6 auto-half-100 7 auto-full-10 8 auto-half-10 9 fixed-full-100 10 fixed-half-100 11 fixed-full-10 12 fixed-half-10 14 auto-1000 15 fixed-full-1000	.0.1.1.10
ethPhyEthAssignedIfIndexobsolete The Ethernet interface index the PHY or switch port is connected/assigned to. The system will create interfaces as needed, but there can't be more ethernet interfaces than switch ports.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.0.1.1.12
ethPhyExtendedDistance If the PHY supports different receive thresholds depending on the cable length (long-cable > 100 m) and speed (10BaseT) it could be configured by this variable.	Enumerationr/w Enumerated Values: 1 default 2 short-cable 3 long-cable	.0.1.1.13
ethPhyPortGroup The port group this phy is member of.	Integer32r/w Constraints: range: 0-99	.0.1.1.18
ethPhyPortDescr This object is available to the user for specifying a user-friendly name or tag.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.0.1.1.21
ethPhyPortFlowControl If the PHY supports flow control according to IEEE 802.3x flow control can be enabled on that port by setting variable to value 'auto'. This will cause 802.3x to be advertised via that port as well as enabled automatica…	Enumerationr/w Enumerated Values: 1 disable 2 enable 3 auto	.0.1.1.22
ethPhyPortFlowControlStatus This variable indicates whether flow control according to IEEE 802.3x is currently active on that port. Possible values are ... disabled(1) and enabled(2)	Enumeration Enumerated Values: 1 disabled 2 enabled	.0.1.1.23