BIANCA-BRICK-E3-MIB Table View

The e3IfTable contains information relating to the 
interfaces available on the system. Each entry corresponds to
an available e3 interface. Entries cannot be added or 
	deleted by the user. 
          
Creating entries: Entries are created by the system
automatically when a new e3 module is installed.
          
Deleting entries: Entries are removed by the system
after the appropriate e3 module is removed.

e3IfEntry row .1.3.6.1.4.1.272.4.42.1.1

Indexes

e3IfIndex

Column	Syntax	OID
e3IfIndexmandatory The unique interface index of the e3/ds3 interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.272.4.42.1.1.1
e3IfTypemandatory The e3 physical interface type off(1) interface is switched offline and the line interface unit is switched off. e3-unframed(2) Synchronous 34.368 MBit/s fullduplex, with HDB3 line coding. ds3-unframed(3) Synchron…	Enumerationr/w Enumerated Values: 1 off 2 e3-unframed 3 ds3-unframed 4 sts1-unframed	.1.3.6.1.4.1.272.4.42.1.1.2
e3IfClockmandatory The clock source of the E3/DS3 connection. intern(1) Your router provides the master clock of the E3/DS3 connection. extern(2) Your telephone company or the remote DSU provides the master clock of the E3/DS3 conn…	Enumerationr/w Enumerated Values: 1 intern 2 extern 3 extern-preferred	.1.3.6.1.4.1.272.4.42.1.1.5
e3IfL2Modemandatory The X.75 layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE the address in a command frame is 0x01, when configured as DCE it is 0x03. For response fram…	Enumerationr/w Enumerated Values: 1 dte 2 dce 3 auto	.1.3.6.1.4.1.272.4.42.1.1.10
e3IfTestPatternmandatory This variable configures which test pattern should be transmitted. normal(1) normal data, no test pattern is transmitted. ones(2) Transmit unframed all ones. alt-0-1(3) Transmit unframed 101010... pattern in E3 mode …	Enumerationr/w Enumerated Values: 1 normal 2 ones 3 alt-0-1 4 prbs	.1.3.6.1.4.1.272.4.42.1.1.11
e3IfLoopbackmandatory This variable represents the loopback configuration of the E3/DS3 interface. noloop(1) No loopback is configured, normal data is transmitted and received. remoteloop(2) The received data is transmitted again. Receiv…	Enumerationr/w Enumerated Values: 1 noloop 2 remoteloop 3 localloop	.1.3.6.1.4.1.272.4.42.1.1.12
e3IfBundlemandatory Index of the bundle to aggregate the interface and channels of other interfaces to one interface.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.272.4.42.1.1.14
e3IfCableLengthmandatory 'short' should be used for a cable lenght less then 225 feet. 'long' should be used otherwise. With 'short' the Tx signal is preattenutated similar to the attenuation of 225 feet coaxial cable. The setting has no effe…	Enumerationr/w Enumerated Values: 1 short 2 long	.1.3.6.1.4.1.272.4.42.1.1.15
e3IfCRCModemandatory The type of CRC checksum of the HDLC frames. crc16(1) 16 Bit CRC crc32(2) 32 Bit CRC	Enumerationr/w Enumerated Values: 1 crc16 2 crc32	.1.3.6.1.4.1.272.4.42.1.1.16
e3IfL1Statemandatory The e3 physical layer state down(1) physical layer is inactive up(2) physical layer is active prbs(3) physical layer is active, a PRBS signal is detected nolicense(4) a license must be configured to activate the i…	Enumeration Enumerated Values: 1 down 2 up 3 prbs 4 nolicense	.1.3.6.1.4.1.272.4.42.1.1.19
e3IfRxPacketsmandatory Count of received valid HDLC Frames.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.20
e3IfRxOctetsmandatory Count of received bytes.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.21
e3IfTxPacketsmandatory Count of transmitted valid HDLC Frames.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.22
e3IfTxOctetsmandatory Count of transmitted bytes.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.23
e3IfRxResetsmandatory Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.24
e3IfRxAbortsmandatory Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.25
e3IfRxOverrunsmandatory Count of receiver overruns. If the e3 port is unable to grant sufficiently soon/often the bus, the RxFIFO may fill up. This leads to loss of data.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.26
e3IfRxCRCErrorsmandatory Count of corrupted frames. Errors due to interference on the e3 cable.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.27
e3IfRxGiantFramesmandatory Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.28
e3IfTxResetsmandatory Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.29
e3IfTxAbortsmandatory Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as illegal.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.30
e3IfTxUnderrunsmandatory Count of transmitter underruns. The e3 data for the e3 port is supplied too slowly.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.31
e3IfTxGiantFramesmandatory Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.272.4.42.1.1.32