BAY-STACK-EAPOL-EXTENSION-MIB Table View

This table is used to control the EAP multihost configuration
for each port in the system.

bseePortConfigEntry row .1.3.6.1.4.1.45.5.3.3.1

The EAP multihost configuration for a port.

Indexes

bseePortConfigPortNumber

Column	Syntax	OID
bseePortConfigPortNumber The Port number associated with this Port.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.3.1.1
bseePortConfigGuestVlanId This object specifies the ID of the guest VLAN for this port. Access to the guest VLAN is allowed for MAC addresses before EAP authentication has been performed. If the value of this object is 0, then the…	Q-BRIDGE-MIBVlanIdOrNoner/w Type Constraints: range: 0..4094	.1.3.6.1.4.1.45.5.3.3.1.2
bseePortConfigMultiHostEnabled This object controls whether EAP multihost is enabled for a port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.3
bseePortConfigMultiHostEapMaxNumMacs This object specifies the maximum number of EAP-authentication MAC addresses allowed on this port. A value of 0 indicates that there is no port-specific limit.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.45.5.3.3.1.4
bseePortConfigMultiHostAllowNonEapClient This object controls whether non-EAP clients (MAC addresses) are allowed on the port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.5
bseePortConfigMultiHostNonEapMacSourcedeprecated This object controls the source for finding allowed non-EAP MAC addresses.	Enumerationr/w Enumerated Values: 1 autoLearn 2 userConfig 3 radius	.1.3.6.1.4.1.45.5.3.3.1.6
bseePortConfigMultiHostNonEapMaxNumMacs This object specifies the maximum number of non-EAP authenticated MAC addresses allowed on this port.	Integer32r/w Constraints: range: 1-100	.1.3.6.1.4.1.45.5.3.3.1.7
bseePortConfigGuestVlanEnabled This object controls whether access to the guest VLAN is allowed for a port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.8
bseePortConfigMultiHostRadiusAuthNonEapClient This object controls whether non-EAP clients (MAC addresses) may authenticated using RADIUS on the port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.9
bseePortConfigMultiHostSingleAuthEnabled This object controls whether non-EAP clients (MAC addresses) may be automatically authenticated on the port after an EAP client has been authenticated (known as MHSA).	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.10
bseePortConfigMultiHostAllowNonEapPhones This object indicates whether IP phones will be allowed access based on DHCP.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.11
bseePortConfigMultiHostAllowRadiusAssignedVlan This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.12
bseePortConfigMultiHostEapPacketMode This object indicates whether to use unicast or multicast packets for Eap-ReqId packets. Normally, multicast packets are used.	Enumerationr/w Enumerated Values: 1 multicast 2 unicast	.1.3.6.1.4.1.45.5.3.3.1.13
bseePortConfigMultiHostEapRadiusTimeoutMode This object indicates whether or not to fail authentication of EAP users on a RADIUS timeout.	Enumerationr/w Enumerated Values: 1 fail 2 doNotFail	.1.3.6.1.4.1.45.5.3.3.1.14
bseePortConfigMultiHostAllowNonEapRadiusAssignedVlan This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode for non-EAP clients.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.15
bseePortConfigProcessRadiusRequestsServerPackets This object indicates whether to process any RADIUS requests-server packets that are received on this port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.16
bseePortConfigEapProtocolEnabled This object controls whether EAP protocol packets are processed on this port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.17
bseePortConfigMultiHostUseMostRecentRadiusAssignedVlan Controls whether to use most recent RADIUS-assigned VLAN.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.18
bseePortConfigMultiHostClearNeap Setting this object will clear NEAP authenticated clients from the authentication list. If the value is set to 00:00:00:00:00:00, all clients will be cleared from this port. Otherwise, only a specific client will be c…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.3.1.19
bseePortConfigMultiHostBlockDifferentVlanAuth Controls whether to block authentication of clients which have an associated RADIUS assigned VLAN with an invalid value or different from first client authenticated on the same port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.20
bseePortConfigMultiHostAdacNonEapEnabled This object specifies whether the authentication of Non-EAP phones using ADAC is allowed on this port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.21
bseePortConfigDefaultEapAll This object specifies whether to default all EAP settings on this port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.22
bseePortConfigMultiHostMaxMacs This object specifies the maximum number of EAP and NEAP clients allowed on this port.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.45.5.3.3.1.23
bseePortConfigMultiHostSingleAuthNoLimit This object specifies if we limit the number of non-eap clients on a port authenticated in MHSA.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.24
bseePortConfigFailOpenVlanId This object specifies the ID of the fail-open VLAN for this port in the following format: -1 : Port PVID is used as Fail Open VLAN 0 : the global fail-open VLAN ID is used for this port, as specified in bseeM…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.45.5.3.3.1.25
bseePortConfigFailOpenVlanEnabled This object controls whether fail-open is enabled for a port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.3.1.26
bseePortConfigFailOpenVlanUBP This object represents the UBP filter name of the fail-open policy	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.45.5.3.3.1.27
bseePortConfigCloneSettingsAction This object starts the action of copying eap settings from current ifIndex to the list of ports specified in bseePortConfigCloneSettingsDestPortList. The default value will be returned by all read opperations. The write…	Enumerationr/w Enumerated Values: 1 none 2 start	.1.3.6.1.4.1.45.5.3.3.1.28
bseePortConfigCloneSettingsDestPortList This object represents the destination port list on which the EAP port configuration will be copied. The default value will be returned by all read opperations. The write operation must contain both bseePortConfigCloneS…	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.45.5.3.3.1.29

This table provides the EAP authentication status per-MAC address
per-port.

bseeMultiHostStatusEntry row .1.3.6.1.4.1.45.5.3.4.1

The status of EAP authentication of clients for a port.

Indexes

bseeMultiHostStatusPortNumber bseeMultiHostStatusClientMACAddr

Column	Syntax	OID
bseeMultiHostStatusPortNumber The Port number associated with this client.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.4.1.1
bseeMultiHostStatusClientMACAddr The MAC address of the client.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.4.1.2
bseeMultiHostStatusPaeState The current value of the Authenticator PAE state machine.	Enumeration Enumerated Values: 1 initialize 2 disconnected 3 connecting 4 authenticating 5 authenticated 6 aborting 7 held 8 forceAuth 9 forceUnauth	.1.3.6.1.4.1.45.5.3.4.1.3
bseeMultiHostStatusBackendAuthState The current state of the Backend Authentication state machine.	Enumeration Enumerated Values: 1 request 2 response 3 success 4 fail 5 timeout 6 idle 7 initialize	.1.3.6.1.4.1.45.5.3.4.1.4
bseeMultiHostStatusReauthenticate Setting this object to reauthenticate(2) will force the client to be reauthenticated. When retrieved, the value of this object is always other(1).	Enumerationr/w Enumerated Values: 1 other 2 reauthenticate	.1.3.6.1.4.1.45.5.3.4.1.5
bseeMultiHostStatusVid The Vlan ID associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 4095.	Q-BRIDGE-MIBVlanIdOrAny Type Constraints: range: 1..4095	.1.3.6.1.4.1.45.5.3.4.1.6
bseeMultiHostStatusPri The Vlan priority value associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 8.	Integer32 Constraints: range: 0-8	.1.3.6.1.4.1.45.5.3.4.1.7
bseeMultiHostStatusFaBindings The EAP vlan:isid bindings. Vlan is represented on 2 bytes. Isid is represented on 4 bytes. The output OctetString would be a continuous hexadecimal representation of VLAN followed by corresponding ISID. Example: L…	OctetString Constraints: range: 0-96	.1.3.6.1.4.1.45.5.3.4.1.8
bseeMultiHostStatusPacpState The current value of the Authenticator PACP state machine.	Enumeration Enumerated Values: 1 initialize 2 unauthenticated 3 authenticating 4 authenticated 5 held	.1.3.6.1.4.1.45.5.3.4.1.9

A table that contains the session statistics objects for the
Authenticator PAE associated with each EAP client on each Port.
An entry appears in this table for each client MAC address on each
port that may authenticate access to itself.

bseeMultiHostSessionStatsEntry row .1.3.6.1.4.1.45.5.3.5.1

The session statistics information for an Authenticator
PAE. This shows the current values being collected for
each session that is still in progress, or the final
values for the last valid session for each client where…

Indexes

bseeMultiHostSessionStatsPortNumber bseeMultiHostSessionStatsClientMACAddr

Column	Syntax	OID
bseeMultiHostSessionStatsPortNumber The Port number associated with this client.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.5.1.1
bseeMultiHostSessionStatsClientMACAddr The MAC address of this client.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.5.1.2
bseeMultiHostSessionId A unique identifier for the session, in the form of a printable ASCII string of at least three characters.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.45.5.3.5.1.3
bseeMultiHostSessionAuthenticMethod The authentication method used to establish the session.	Enumeration Enumerated Values: 1 remoteAuthServer 2 localAuthServer	.1.3.6.1.4.1.45.5.3.5.1.4
bseeMultiHostSessionTime The duration of the session in seconds.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.45.5.3.5.1.5
bseeMultiHostSessionTerminateCause The reason for the session termination.	Enumeration Enumerated Values: 1 supplicantLogoff 2 portFailure 3 supplicantRestart 4 reauthFailed 5 authControlForceUnauth 6 portReInit 7 portAdminDisabled 999 notTerminatedYet	.1.3.6.1.4.1.45.5.3.5.1.6
bseeMultiHostSessionUserName The User-Name representing the identity of the Supplicant PAE.	SNMP-FRAMEWORK-MIBSnmpAdminString Type Constraints: range: 0..255	.1.3.6.1.4.1.45.5.3.5.1.7

A table that contains the non-EAP MAC addresses that are
allowed access to EAP-enabled interfaces.

bseeMultiHostNonEapMacEntry row .1.3.6.1.4.1.45.5.3.6.1

An allowed non-EAP MAC address.

Indexes

bseeMultiHostNonEapMacPortNumber bseeMultiHostNonEapMacClientMACAddr

Column	Syntax	OID
bseeMultiHostNonEapMacPortNumber The Port number on which the MAC address is allowed.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.6.1.1
bseeMultiHostNonEapMacClientMACAddr The MAC address allowed on the port.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.6.1.2
bseeMultiHostNonEapMacRowStatus This is used to control creation/deletion of entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.45.5.3.6.1.3

This table provides the authentication status of non-EAP
clients per-MAC address per-port.

bseeMultiHostNonEapStatusEntry row .1.3.6.1.4.1.45.5.3.7.1

The status of authentication of a non-EAP client for a port.

Indexes

bseeMultiHostNonEapStatusPortNumber bseeMultiHostNonEapStatusClientMACAddr

Column	Syntax	OID
bseeMultiHostNonEapStatusPortNumber The Port number associated with this client.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.7.1.1
bseeMultiHostNonEapStatusClientMACAddr The MAC address of the client.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.7.1.2
bseeMultiHostNonEapStatusState The authentication status. Values are: rejected(1) - the MAC address could not be authenticated on this port locallyAuthenticated(2) - the MAC address was authenticated …	Enumeration Enumerated Values: 1 rejected 2 locallyAuthenticated 3 radiusPending 4 radiusAuthenticated 5 adacAuthenticated 6 mhsaAuthenticated 7 lldpAuthenticated 8 radiusHeld	.1.3.6.1.4.1.45.5.3.7.1.3
bseeMultiHostNonEapStatusReauthenticate Setting this object to reauthenticate(2) will force the MAC address to be reauthenticated. When retrieved, the value of this object is always other(1).	Enumerationr/w Enumerated Values: 1 other 2 reauthenticate	.1.3.6.1.4.1.45.5.3.7.1.4
bseeMultiHostNonEapStatusVid The Vlan ID associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 4095.	Q-BRIDGE-MIBVlanIdOrAny Type Constraints: range: 1..4095	.1.3.6.1.4.1.45.5.3.7.1.5
bseeMultiHostNonEapStatusPri The Vlan priority value associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 8.	Integer32 Constraints: range: 0-8	.1.3.6.1.4.1.45.5.3.7.1.6
bseeMultiHostNonEapStatusFaBindings The NEAP vlan:isid bindings. Vlan is represented on 2 bytes. Isid is represented on 4 bytes. The output OctetString would be a continuous hexadecimal representation of VLAN followed by corresponding ISID. Example: …	OctetString Constraints: range: 0-96	.1.3.6.1.4.1.45.5.3.7.1.7

A table that contains the user name and password for the
Supplicant PAE associated with each port.
An entry appears in this table for each port that may
authenticate itself when challenged by a remote system.

bseeSupplicantUserEntry row .1.3.6.1.4.1.45.5.3.9.1

The configuration information for a Supplicant PAE.

Indexes

bseeSupplicantPortNumber

Column	Syntax	OID
bseeSupplicantPortNumber A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system …	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.9.1.1
bseeSupplicantUserName The user name currently in use by the Supplicant PAE state machine.	OctetStringr/w Constraints: range: 0-15	.1.3.6.1.4.1.45.5.3.9.1.2
bseeSupplicantPassword The password currently in use by the Supplicant PAE state machine.	OctetStringr/w Constraints: range: 0-15	.1.3.6.1.4.1.45.5.3.9.1.3
bseeSupplicantUserState Input the user state to logoff.	Enumerationr/w Enumerated Values: 1 inactive 2 active 3 logoff	.1.3.6.1.4.1.45.5.3.9.1.4

A table that contains EAP VoIP Vlan settings.

bseeMultiHostVoipVlanEntry row .1.3.6.1.4.1.45.5.3.10.1

The configuration information for an EAP VoIP Vlan.

Indexes

bseeMultiHostVoipVlanIndex

Column	Syntax	OID
bseeMultiHostVoipVlanIndex A unique identifier for each entry.	Integer32 Constraints: range: 1-5	.1.3.6.1.4.1.45.5.3.10.1.1
bseeMultiHostVoipVlanId This object specifies the Vlan ID of the VoIP Vlan.	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.45.5.3.10.1.2
bseeMultiHostVoipVlanEnabled This object specifies whether to use this VoIP Vlan.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.5.3.10.1.3

This table provides the list of DHCP authenticated IP phones 
per-MAC address per-port.

bseeMultiHostDhcpAuthPhoneEntry row .1.3.6.1.4.1.45.5.3.11.1

The DHCP authenticated IP phone for a port.

Indexes

bseeMultiHostDhcpAuthPhonePortNumber bseeMultiHostDhcpAuthPhoneClientMACAddr

Column	Syntax	OID
bseeMultiHostDhcpAuthPhonePortNumber The port number associated with the DHCP authenticated IP phone.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.11.1.1
bseeMultiHostDhcpAuthPhoneClientMACAddr The MAC address of the DHCP authenticated IP phone.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.11.1.2
bseeMultiHostDhcpAuthPhoneUserName The user name currently in use by the DHCP authenticated IP phone.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.45.5.3.11.1.3

This table provides the session status per-MAC address
per-port for unauthenticated MACs.

bseeUnauthenticatedStatusEntry row .1.3.6.1.4.1.45.5.3.12.1

The status of authentication of clients for a port.

Indexes

bseeUnauthenticatedStatusPortNumber bseeUnauthenticatedStatusClientMACAddr

Column	Syntax	OID
bseeUnauthenticatedStatusPortNumber The Port number associated with this client.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.5.3.12.1.1
bseeUnauthenticatedStatusClientMACAddr The MAC address of the client.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.5.3.12.1.2
bseeUnauthenticatedStatusType The reason for unauthentication: intruder MAC (failed authentication), MAC is in guest VLAN, MAC is in fail-open VLAN or it is stored directly after a single authentication (MHSA).	Enumeration Enumerated Values: 1 intruders 2 guest 3 failOpen 4 mhsa	.1.3.6.1.4.1.45.5.3.12.1.3
bseeUnauthenticatedStatusRadiusStatus Status for clients who attempted authentication by a Radius server.	Enumeration Enumerated Values: 1 noRequest 2 pending 3 timeout 4 reject 5 delayed	.1.3.6.1.4.1.45.5.3.12.1.4